Earlier RDDS (Rounded Damped Detuned Structures) [1,2], designed, fabricated and tested at SLAC, in collaboration with KEK, have been shown to damp wakefields successfully. However, electrical breakdown has been found to occur in these structures and this makes them inoperable at the desired gradient. Recent results [3] indicate that lowering the group velocity of the accelerating mode reduces electrical breakdown events. In order to preserve the filling time of each structure a high synchronous phase advance (150 degrees as opposed to 120 used in previous NLC designs) has been chosen. Here, damping of the wakefield is analyzed. Manifold damping and interleaving of structure cell frequencies is discussed. These wakefields impose alignment tolerances on the cells and on the structure as a whole. Tolerance calculations are performed and these are compared with analytic estimations.
We explore the NLC linac optics compatible with a low energy scenario where initially only part of the full linac is installed. Optics modification suitable for a low energy beam running and upgrade to the nominal energy is discussed. Linac parameters and beam tolerances in the modified lattice are compared to the nominal design.
The injector linacs of the JLC/NLC project include the prelinac, the e+ drive linac, the $e- booster, and the $e+ booster. The first three will be S-band machines, the last one, an L-band machine. We have demonstrated that by using detuning alone in the accelerator structure design of these linacs we will have acceptable tolerances for emittance growth due to both injection jitter and structure misalignments, for both the nominal (2.8ns) and alternate (1.4ns) bunch spacings.
The vibration of components of the NLC linac, such as accelerating structures and girders, is being studied both experimentally and analytically. Various effects are being considered including structural resonances and vibration caused by cooling water in the accelerating structure. This paper reports the status of ongoing work.
Vertical vibration of linac components (accelerating structures, girders and quadrupoles) in the NLC has been studied experimentally and analytically. Effects such as structural resonances and vibration caused by cooling water both in accelerating structures and quadrupoles have been considered. Experimental data has been compared with analytical predictions and simulations using ANSYS. A design, incorporating the proper decoupling of structure vibrations from the linac quadrupoles, is being pursued.
Vertical vibration of linac components (accelerating structures, girders and quadrupoles) in the NLC has been studied experimentally and analytically. Effects such as structural resonances and vibration caused by cooling water both in accelerating structures and quadrupoles have been considered. Experimental data has been compared with analytical predictions and simulations using ANSYS. A design, incorporating the proper decoupling of structure vibrations from the linac quadrupoles, is being pursued.
The proposed Next Linear Collider (NLC) contains linac systems operating at L,S,C, and X band. This paper describes a wideband modular low-level RF (LLRF) system applicable for all NLC pulsed RF systems. High speed digital IF techniques are used for both arbitrary klystron drive modulation and accurate RF vector detection. Measurement of relative beam to RF phase, beam loading compensation, and structure dipole modes for automated alignment are all handled by the system. Modern signal processing techniques are also described.
An alternative being considered for the Next Linear Collider (NLC) is not to tunnel in a straight line but to bend the Main Linac into an arc so as to follow an equipotential. We begin here an examination of the effects that this would have on vertical dispersion, with its attendant consequences on synchrotron radiation and emittance growth by looking at two scenarios: a gentle continuous bending of the beam to follow an equipotential surface, and an introduction of sharp bends at a few sites in the linac so as to reduce the maximum sagitta produced.
The vibration stability requirements for the Next Linear Collider (NLC) are far more stringent than for the previous generation of Colliders. To meet these goals, it is imperative that the effects of vibration on NLC Linac components from near-field sources (e.g. compressors, high vacuum equipment, klystrons, modulators, pumps, fans, etc) be well understood. The civil construction method, whether cut-and-cover or parallel bored tunnels, can determine the proximity and possible isolation of noise sources. This paper presents a brief summary and analysis of recently completed and planned studies…
Extensive beam-based feedback systems are planned as an integral part of the Next Linear Collider (NLC) control system. Wakefield effects are a significant influence on the feedback design, imposing both architectural and algorithmic constraints. Studies are in progress to assure the optimal selection of devices and to refine and confirm the algorithms for the system design. We show the results of initial simulations, along with evaluations of system response for various conditions of ground motion and other operational disturbances.
In order to mitigate the effects of electrical breakdown (which have been found to occur in SLAC X-band traveling wave structures) standing wave structures are being considered for the NLC linac. At SLAC, structures consisting of 15 cells operating in the p accelerating mode are being tested for their electrical breakdown characteristics. In this paper the tuning requirement on the cavities is elucidated by utilizing a circuit model of the structure. The sensitivity of the field to both random and systematic errors is also discussed.
In the NLC (Next Linear Collider) small misalignments in each of the individual accelerator structures (or the accelerator cells) will give rise to wakefields which kick the beam from its electrical axis. This wakefield can cause BBU (Beam Break Up) or at the very least it will dilute the emittance of the beam. Several Gaussian detuned structures have been designed and tested [1] at SLAC and in this paper we explore new distributions with possibly better damping properties. The progress of the beam through approximately 5,000 structures is monitored in phase space and results on this are prese…
The injector linacs of the JLC/NLC comprise the e+ booster, the e- drive linac, the e+ booster, and the two prelinacs. These four systems together transport the two types of beams from the 80 MeV point at the end of their respective bunchers up to the storage rings, and then from the storage rings to the 10 GeV point at the beginning of the bunch compressors. Nominally, the e+ booster structure will be L-band and the others S-band. In transport through these linacs it is important that the emittances and particle losses stay within specified tolerances. In particular, the effects of the dipole…
The main linacs of the Next Linear Collider (NLC) will contain several thousand X-band RDDS (Rounded Damped Detuned Structures). The transverse wakefield in the structures is reduced by detuning the modal frequencies such that they destructively interfere and by four damping manifolds per structure which provide weak damping. Errors in the fabrication of the individual cells and in the alignment of the cells will reduce the cancellation of the modes. Here, we calculate the tolerances on random errors in the synchronous frequencies of the cells and the cell-to-cell alignment.
Dipole wakefields in NLC (Next Linear Collider) structures have been measured with ASSET [1] and well predicted by a circuit model [2]. However, the experimental technique is both time-consuming and expensive. Here, we report on kick factor and synchronous frequency determination for 1st and higher order dipole bands for TW (Traveling Wave) accelerators via a wire measurement technique. This stand-alone technique is relatively inexpensive and may lead to an efficient determination of wakefield parameters. The perturbative effect of the wire on the dipole band is pointed out and a two-wire sche…
The effects on beam dynamics from long-range and short-range wakefields from TESLA-type cavities are considered in regard to a proposed FEL oscillator (FE-LO) operating at 120 nm. This would be driven by the Fermilab Accelerator Science and Technology (FAST) linac at 300 MeV with a 3-MHz micropulse repetition rate. Our wakefield studies showed measurable effects on submacropulse centroid stability and on submicropulse head-tail kicks that can lead to emittance degradation. In the case of the former, we use MINERVA/OPC to simulate the ~100-$μ$m centroid slew effects on the saturated output powe…
We report on suppression of long-range wakefields in CLIC accelerating structures. Strong detuning and moderate damping is employed. In these initial design studies we focus on the CLIC_G structure and enforce a moderate Q of 300 and 500. We maintain a dipole bandwidth of approximately 1 GHz as specified from breakdown constraints in a modified structure, CLIC_DDS. The circuit model, which facilitates a rapid design of manifolds slot-coupled to the main accelerating cells, is described.
The progress of a multiple bunches of electrons through several thousand accelerator structures results in a wakefield which if left unchecked will kick successive bunches off the axis of the accelerator and can at the very least dilute the final luminosity of the final colliding beams, or at worst can lead to a BBU (Beam Break Up) instability. In order to damp the wakefields to acceptable levels for travelling wave structures we detune the frequencies of the cells and we couple out the field to four adjacent manifolds. Optimizing the manifold-cell coupling for several hundred cells and changi…
A Damped Detuned Structure (DDS) for CLIC main linac has been proposed as an alternative to the present baseline design which is based on heavy damping. A first prototype, CLIC_DDS_A, for high power tests has been already designed and is under construction. It is also foreseen to design a further prototype, CLIC_DDS_B, to test both the wakefield suppression and high power performances. Wakefield calculations for DDS are, in the early design stage, based on single infinitely periodic cells. Though cell-to-cell interaction is taken into account to calculate the wakefields, it is important to stu…
In the NLC project multiple bunches of electrons and positrons will be accelerated initially to a centre of mass of 500 GeV and later to 1 TeV or more. In the process of accelerating 192 bunches within a pulse train, wakefields are excited which kick the trailing bunches off axis and can cause luminosity dilution and BBU (Beam Break Up). Several structures to damp the wakefield have been designed and tested at SLAC and KEK and these have been found to successfully damp the wakefield [1]. However, these 2pi/3 structures suffered from electrical breakdown and this has prompted us to explore lowe…
The present design of the main accelerating structure for CLIC is based on heavy damping (WDS) with a Q of ~10. The wakefield suppression in this case entails locating the damping materials in relatively close proximity to the accelerating cells. Herein we present an alternate design for the main accelerating structures. We detune the lowest dipole band by prescribing a Gaussian distribution to the cell parameters and consider moderate damping Q~500 to prevent the recoherence of the modes; in this case the damping materials can be located at an extended distance from the accelerating structure…
The shape of an RF pulse is distorted upon propagating through an X-band accelerator structure due to dispersive effects. This distortion together with beam loading introduce energy spread between 192 bunches. In order to minimize this energy spread we modify the input RF pulse shape. The pulse propagation, energy gain, and beam loading are modelled with a mode-matching computer code and a circuit model. A 2D model and a circuit model of a complete 60 cm structure, consisting of 55 cells and input and output couplers is analyzed. This structure operates with a 5pi/6 phase advance per cell. Dis…
The proposed Next Linear Collider contains a large number of linac RF systems with new requirements for wideband klystron modulation and accurate RF vector detection. The system will be capable of automatically phasing each klystron and compensating for beam loading effects. Accelerator structure alignment is determined by detection of the beam induced dipole modes with a receiver similar to that used for measuring the accelerator RF and is incorporated into the RF system topology. This paper describes the proposed system design, signal processing techniques and includes preliminary test resul…
The number of cells in a $π$-mode standing wave (SW) accelerating structure for the Compact linear Collider (CLIC) project is limited by mode overlap with nearby modes. The distributed coupling scheme avoids mode overlap by treating each cell as independent. Designs of cells suitable for distributed coupling with strong wakefield damping have not previously been studied. In this paper we develop a SW cell to be used in a distributed coupling structure that can satisfy the CLIC transverse wakepotential limit. From the middle cell of the CLIC-G* travelling wave (TW) structure, a SW cell is desig…
In damping the wakefield generated by an electron beam traversing several thousand X-band linacs in the NLC we utilise a Gaussian frequency distribution of dipole modes to force the modes to deconstructively interfere, supplemented with moderate damping achieved by coupling these modes to four attached manifolds. Most of these modes are adequately damped by the manifolds. However, the modes towards the high frequency end of the lower dipole band are not adequately damped because the last few cells are, due to mechanical fabrication requirements, not coupled to the manifolds. To mitigate this p…
Recent experiments at SLAC [1,2] and CERN [3] have revealed evidence of significant deformation in the form of "pitting" of the cells of the 1.8m series of structures DDS/RDDS (Damped Detuned Structure/Rounded Damped Detuned Structure). This pitting occurs in the high group velocity (vg /c = 0.012) end of the accelerating structure and little evidence of breakdown has been found in the lower group velocity end of the structure. Additional, albeit preliminary experimental evidence, suggests that shorter and lower group velocity structures have reduced breakdown events with increasing accelerati…
In designing linear accelerator structures for multi-bunch applications we are often interested in estimating the effect of relatively weak multi-bunch beam break-up (BBU), due to the somewhat complicated wakefields of detuned structures. This, for example, is the case for the injector linacs of the JLC/NLC linear collider project. Deriving an analytical formula for such a problem is the subject of this report.
The implications of long-range wakefields on the beam quality are investigated through a detailed beam dynamics study. Injection offsets are considered and the resulting emittance dilution recorded, including systematic sources of error. These simulations have been conducted for damped and detuned structures (DDS) and for waveguide damped structures-both for the CLIC collider.
During the initial phase of operation, the linacs of the Next Linear Collider (NLC) will contain roughly 5000 X-Band accelerator structures that will accelerate beams of electrons and positrons to 250 GeV. These structures will nominally operate at an unloaded gradient of 72 MV/m. As part of the NLC R&D program, several prototype structures have been built and operated at the Next Linear Collider Test Accelerator (NLCTA) at SLAC. Here, the effect of high gradient operation on the structure performance has been studied. Significant progress was made during the past year after the NLCTA power so…
A linear accelerator structure, such as will be used in the linacs of the JLC/NLC collider, is composed of on the order of 100 cells. The cells are constructed as individual cups that are brazed together to form a structure. Fabrication error will result in slight cell-to-cell misalignments along the finished structure. In this report we derive an approximation to the transverse wakefield of a structure with cell-to-cell misalignments in terms of the eigenfunctions and eigenvalues of the error-free structure.
We show that scattering matrix calculations for dipole modes between 23-43 GHz for the 206 cell detuned structure (DS) are consistent with finite element calculations and results of the uncoupled model. In particular, the rms sum wake for these bands is comparable to that of the first dipole band. We also show that for RDDS1 uncoupled wakefield calculations for higher bands are consistent with measurements. In particular, a clear 26 GHz signal in the short range wake is found in both results.
During the course of the last decade, traveling wave accelerating structures for a future Linear Collider have been the object of intense R&D efforts. An important problem is the efficient computation of the long range wakefield with the ability to include small alignment and tuning errors. To that end, SLAC has developed an RF circuit model with a demonstrated ability to reproduce experimentally measured wakefields. The wakefield computation involves the repeated solution of a deterministic system of equations over a range of frequencies. By taking maximum advantage of the sparsity of the equ…
This paper outlines the RF design of the CLIC (Compact Linear Collider) 30 GHz main linac accelerating structure and gives the resulting longitudinal and transverse mode properties. The critical requirement for multibunch operation, that transverse wakefields be suppressed by two orders of magnitude within 0.7 ns (twenty fundamental mode cycles), has been demonstrated in a recent ASSET experiment. The feasibility of operating the structure at an accelerating gradient of 150 MV/m for 130 ns has yet to be demonstrated. Damage of the internal copper surfaces due to high electric fields or resulti…
The RadiaBeam/SLAC dechirper, a structure consisting of pairs of flat, metallic, corrugated plates, %a corrugated structure in flat geometry, has been installed just upstream of the undulators in the Linac Coherent Light Source (LCLS). As a dechirper, with the beam passing between the plates on axis, longitudinal wakefields are induced that can remove unwanted energy chirp in the beam. However, with the beam passing off axis, strong transverse wakes are also induced. This mode of operation has already been used for the production of intense, multi-color photon beams using the Fresh-Slice techn…
Operating the SLAC/KEK DDS (Damped Detuned Structure) X-band linacs at high gradients (in excess of 70MV/m) has recently been found to be limited by the accelerator structures breaking down and as a consequence severe damage occurs to the cells which makes the structures inoperable. A series of recent experiments at SLAC indicates that arcing in the structures is significantly reduced if the group velocity of the accelerating mode is reduced and additionally it has been discovered that reducing the length of the accelerating structure also limits the number and intensity of breakdown events [1…
Interaction between the bunches in the NLC main linac via long range wakefields can cause a beam breakup instability. Although the magnitude of the long range wakefields for an ideal NLC structure is below the instability threshold, the wake increases when structure manufacturing errors are taken into account. In case of large errors, the developing instability can result in the projected emittance dilution of the bunch train. To suppress the instability, we propose to introduce an energy spread between the bunches, similar to the BNS energy spread for damping of the beam breakup within a sing…
In the JLC/NLC X-band linear collider, it is essential to reduce the long-range dipole wakefields in the accelerator structure to prevent beam break up (BBU) and emittance degradation. The two methods of reducing the long-range wakefields are detuning and damping. Detuning reduces the wakefields rapidly as the dipole modes de-cohere but, with a finite number of modes, the wakefield will grow again as the modes re-cohere. In contrast, damping suppresses the wakefields at a longer distance. There are two principal damping schemes: synchronous damping using HOM manifolds such as that used in the …
The complexity of the Round Damped Detuned Structue (RDDS) for the JLC/NLC main linac is driven by the considerations of rf efficiency and dipole wakefield suppression. As a time and cost saving measure for the JLC/NLC, the dimensions of the 3D RDDS cell are being determined through computer modeling to within fabrication precision so that no tuning may be needed once the structures are assembled. The tolerances on the frequency errors for the RDDS structure are about one MHz for the fundamental mode and a few MHz for the dipole modes. At the X-band frequency, these correspond to errors of a m…
Electron beams of linear induction accelerators experience deflective forces caused by RF fields building up as a result of accelerating cavities of finite size. These forces can significantly effect the beam when a long linac composed of identical cells is assembled. Recent techniques in computational modeling, simulation, and experiments for 20 MeV DARHT-II (Dual Axis Radiographic Hydrodynamic Test) accelerator cells were found to reduce the wakefield impedance of the cells from 800 ohms/meter to 350 ohms/meter and experimental results confirm the results of the modeling efforts. Increased p…
Higher order modes (HOMs) are simulated with finite element and finite difference computer codes for the ILC superconducting cavities. In particular, HOMs in KEK's Ichiro type of cavity and Cornell University's Reentrant design are focused on in this work. The aim, at these universities and laboratories, is to achieve an accelerating gradient in excess of 50 MV/m in 9-cell superconducting cavities whilst maintaining a high quality and stable electron beam. At these gradients, electrical breakdown is an important cause for concern and the wakefields excited by the energetic electron beams are a…
In previous work [1] general expressions, valid for arbitrary bunch lengths, were derived for the wakefields of corrugated structures with flat geometry, such as is used in the RadiaBeam/LCLS dechirper. However, the bunch at the end of linac-based X-ray FELs--like the LCLS--is extremely short, and for short bunches the wakes can be considerably simplified. In this work, we first derive analytical approximations to the short-range wakes. These are generalized wakes, in the sense that their validity is not limited to a small neighborhood of the symmetry axis, but rather extends to arbitrary tran…
A unique facility for laser plasma physics and advanced accelerator research has been built recently at Tsinghua Universtiy. This system is based on Tsinghua Thomson scattering X-ray source (TTX), which combining an ultrafast TW laser with a synchronized 45MeV high brightness linac. In our recent laser wakefield acceleration experiments, we have obtained 10~40MeV high quality monoenergetic electron beams by running the laser at 5TW peak power. Under certain conditions, very low relative energy spread of a few percent can be achieved. Absolute charge calibration for three different scintillatin…
Collinear high-gradient ${\cal O} (GV/m)$ beam-driven wakefield methods for charged-particle acceleration could be critical to the realization of compact, cost-efficient, accelerators, e.g., in support of TeV-scale lepton colliders or multiple-user free-electron laser facilities. To make these options viable, the high accelerating fields need to be complemented with large transformer ratios $>2$, a parameter characterizing the efficiency of the energy transfer between a wakefield-exciting "drive" bunch to an accelerated "witness" bunch. While several potential current distributions have been d…
Particle-in-cell simulations were performed by using PARMELA to characterise an electron injector with a booster linac for the AWAKE project in order to provide the baseline specifications required by the plasma wakefield experiments. Tolerances and errors were investigated. A 3 GHz travelling wave structure designed by using CST code. Particles were tracked by using the field maps acquired from these electromagnetic simulations. These results are pre- sented in comparison with the generic accelerating structure model within PARMELA.
Early tests of short low group velocity and standing wave structures indicated the viability of operating X-band linacs with accelerating gradients in excess of 100 MeV/m. Conventional scaling of traveling wave traveling wave linacs with frequency scales the cell dimensions with l. Because Q scales as l1/2, the length of the structures scale not linearly but as l3/2 in order to preserve the attenuation through each structure. For NLC we chose not to follow this scaling from the SLAC S-band linac to its fourth harmonic at X-band. We wanted to increase the length of the structures to reduce the …
As a joint effort in the JLC/NLC research program, we have developed a new type of damped detuned accelerator structure with optimized round-shaped cavities (RDDS). This paper discusses some important R&D aspects of the first structure in this series (RDDS1). The design aspects covered are the cell design with sub-MHz precision, HOM detuning, coupling and damping technique and wakefield simulation. The fabrication issues covered are ultra-precision cell machining with micron accuracy, assembly and diffusion bonding technologies to satisfactorily meet bookshelf, straightness and cell rotational…
The FLASHForward experimental facility is a high-performance test-bed for precision plasma-wakefield research, aiming to accelerate high-quality electron beams to GeV-levels in a few centimetres of ionised gas. The plasma is created by ionising gas in a gas cell either by a high-voltage discharge or a high-intensity laser pulse. The electrons to be accelerated will either be injected internally from the plasma background or externally from the FLASH superconducting RF front end. In both cases the wakefield will be driven by electron beams provided by the FLASH gun and linac modules operating w…
Plasma-based accelerators (PBAs) driven by either intense lasers (laser wakefield accelerators, LWFAs) or particle beams (plasma wakefield accelerators, PWFAs), can accelerate charged particles at extremely high gradients compared to conventional radio-frequency (RF) accelerators. In the past two decades, great strides have been made in this field, making PBA a candidate for next-generation light sources and colliders. However, these challenging applications necessarily require beams with good stability, high quality, controllable polarization and excellent reproducibility. To date, such beams…
Plasma-based accelerators have made impressive progress in recent years. However, the beam energy spread obtained in these accelerators is still at ~ 1 % level, nearly one order of magnitude larger than what is needed for challenging applications like coherent light sources or colliders. In plasma accelerators, the beam energy spread is mainly dominated by its energy chirp (longitudinally correlated energy spread). Here we demonstrate that when an initially chirped electron beam from a linac with a proper current profile is sent through a low-density plasma structure, the self wake of the beam…
The demands on performance of advanced linear accelerator based facilities strongly depend on the quality of the particle beams produced by such machines. Indeed, state-of-the-art applications in photon production and high-energy physics colliders require to use very high brightness electron beams, implying the coexistence of high peak currents and small transverse emittances. In such systems, the nominal phase-space density may be diluted by the presence of self-induced electromagnetic fields, causing interaction among charged particles through space charge forces and the excitation of wakefi…
