The millimeter wave (mmWave) has received considerable interest due to its expansive bandwidth and high frequency. However, a noteworthy challenge arises from its vulnerability to blockages, leading to reduced coverage and achievable rates. To address these limitations, a potential solution is to deploy distributed reconfigurable intelligent surfaces (RISs), which comprise many low-cost and passively reflected elements, and can facilitate the establishment of extra communication links. In this paper, we leverage stochastic geometry to investigate the ergodic coverage probability and the achievable rate in both distributed RISs-assisted single-cell and multi-cell mmWave wireless communication systems. Specifically, we first establish the system model considering the stochastically distributed blockages, RISs and users by the Poisson point process. Then we give the association criterion and derive the association probabilities, the distance distributions, and the conditional coverage probabilities for two cases of associations between base stations and users without or with RISs. Finally, we use Campbell's theorem and the total probability theorem to obtain the closed-form expressions of the ergodic coverage probability and the achievable rate. Simulation results verify the effectiveness of our analysis method, and demonstrate that by deploying distributed RISs, the ergodic coverage probability is significantly improved by approximately 50%, and the achievable rate is increased by more than 1.5 times.
In millimeter wave (mmWave) systems, it is challenging to ensure the reliable connectivity of communications due to its sensitivity to the presence of blockages. In order to improve the robustness of the mmWave system under the presence of the random blockages, multiple reconfigurable intelligent surfaces (RISs) are deployed to enhance the spatial diversity gain, and robust beamforming is then designed based on a stochastic optimization for minimizing the maximum outage probability among multiple users to ensure the fairness. Under the stochastic optimization framework, we adopt the stochastic…
In this work, we consider the deployment of reconfigurable intelligent surfaces (RISs) to extend the coverage of a millimeter-wave (mmWave) network in indoor dense spaces. We first integrate RIS into ray-tracing simulations to realistically capture the propagation characteristics, then formulate a non-convex optimization problem that minimizes the number of RISs under rate constraints. We propose a feasible point pursuit and successive convex approximation-based algorithm, which solves the problem by jointly selecting the RIS locations, optimizing the RIS phase-shifts, and allocating time reso…
Reconfigurable intelligent surface (RIS) emerges as a promising technology for the next generation networks. In this paper, we utilize the tools from stochastic geometry to study the performance of a RIS-assisted millimeter wave (mmWave) cellular network. Specifically, the locations of the base stations (BSs) and the midpoints of the blockages are modeled as two independent Poisson point processes (PPP) where the blockages are modeled by line boolean model and a fraction of the blockages are coated with RISs. The distinguish characteristics of mmWave communications, i.e., the directional beamf…
Reconfigurable intelligent surface (RIS)-assisted communication appears as one of the potential enablers for sixth generation (6G) wireless networks by providing a new degree of freedom in the system design to telecom operators. Particularly, RIS-empowered millimeter wave (mmWave) communication systems can be a remedy to provide broadband and ubiquitous connectivity. This paper aims to fill an important gap in the open literature by providing a physical, accurate, open-source, and widely applicable RIS channel model for mmWave frequencies. Our model is not only applicable in various indoor and…
In this letter, we optimize the channel estimator of the cascaded channel in an intelligent reflecting surface (IRS)-assisted millimeter wave (mmWave) multi-antenna system. In this system, the receiver is equipped with a hybrid architecture adopting quantized beamforming. Different from traditional multiple-input multiple-output (MIMO) systems, the design of channel estimation is challenging since the IRS is usually a passive array with limited signal processing capability. We derive the optimized channel estimator in a closed form by reformulating the problem of cascaded channel estimation in…
Different from traditional reflection-only reconfigurable intelligent surfaces (RISs), simultaneously transmitting and reflecting RISs (STAR-RISs) represent a novel technology, which extends the half-space coverage to full-space coverage by simultaneously transmitting and reflecting incident signals. STAR-RISs provide new degrees-of-freedom (DoF) for manipulating signal propagation. Motivated by the above, a novel STAR-RIS assisted non-orthogonal multiple access (NOMA) (STAR-RIS-NOMA) system is proposed in this paper. Our objective is to maximize the achievable sum rate by jointly optimizing t…
Reconfigurable intelligent surface (RIS) can be employed in a cell-free system to create favorable propagation conditions from base stations (BSs) to users via configurable elements. However, prior works on RIS-aided cell-free system designs mainly rely on the instantaneous channel state information (CSI), which may incur substantial overhead due to extremely high dimensions of estimated channels. To mitigate this issue, a low-complexity algorithm via the two-timescale transmission protocol is proposed in this paper, where the joint beamforming at BSs and RISs is facilitated via alternating op…
Reconfigurable intelligent surface (RIS) is considered as an extraordinarily promising technology to solve the blockage problem of millimeter wave (mmWave) communications owing to its capable of establishing a reconfigurable wireless propagation. In this paper, we focus on a RIS-assisted mmWave communication network consisting of multiple base stations (BSs) serving a set of user equipments (UEs). Considering the BS-RIS-UE association problem which determines that the RIS should assist which BS and UEs, we joint optimize BS-RIS-UE association and passive beamforming at RIS to maximize the sum-…
This letter focuses on the non-convex joint optimization with a dynamic resource of multi-user for an intelligent reflecting surface-enhanced mmWave system, where all users are concentrated on the unique cluster beam. Firstly, the objective function of the above non-linear problem is converted into a quadratic programming form under the quality of service constraints. Further, a multi-blocks alternating optimization framework with dynamic power allocation is proposed to obtain the maximum sum-rate, where the relaxed ADMM algorithm is adopted to tackle the optimal fulldigital precoder and the c…
Dual Target-Mounted RISs-Assisted ISAC Against Eavesdropping and Malicious Interference
Artificial Intelligence and 6G Laboratory (6GEN. LAB.), Turkcell Iletisim Hizmetleri Inc.（Turkcell通信服务公司人工智能与6G实验室）；Communications and Signal Processing Research (HİSAR) Lab., TÜBİTAK-BİLGEM（TÜBİTAK-BİLGEM通信与信号处理研究实验室）；Department of Electrical and Electronics Engineering, Koc University（罗切斯特大学电气与电子工程系）；Department of Electrical Engineering, Tampere University（坦佩雷大学电气工程系）；Electronics and Communication Department, Istanbul Technical University（伊斯坦布尔理工大学电子与通信系）
The performance characterization of communication systems assisted by large reconfigurable intelligent surfaces (RISs) significantly depends on the adopted models for the underlying channels. Under unrealistic channel models, the system performance may be over- or under-estimated which yields inaccurate conclusions for the system design. In this paper, we review five channel models that are chosen to progressively improve the modeling accuracy for large RISs. For each channel model, we highlight the underlying assumptions, its advantages, and its limitations. We compare the system performance …
This letter focuses on the secure transmission for an intelligent reflecting surface (IRS)-assisted millimeter-wave (mmWave) and terahertz (THz) systems, in which a base station (BS) communicates with its destination via an IRS, in the presence of a passive eavesdropper. To maximize the system secrecy rate, the transmit beamforming at the BS and the reflecting matrix at the IRS are jointly optimized with transmit power and discrete phase-shift constraints. It is first proved that the beamforming design is independent of the phase shift design under the rank-one channel assumption. The formulat…
Reconfigurable intelligent surface (RIS) provides a promising way to build programmable wireless transmission environments. Owing to the massive number of controllable reflecting elements on the surface, RIS is capable of providing considerable passive beamforming gains. At present, most related works mainly consider the modeling, design, performance analysis and optimization of single-RIS-assisted systems. Although there are a few of works that investigate multiple RISs individually serving their associated users, the cooperation among multiple RISs is not well considered as yet. To fill the …
We study the performance of a phase-noise impaired double reconfigurable intelligent surface (RIS)-aided multiuser (MU) multiple-input single-output (MISO) system under spatial correlation at both RISs and base-station (BS). The downlink achievable rate is derived in closed-form under maximum ratio transmission (MRT) precoding. In addition, we obtain the optimal phase-shift design at both RISs in closed-form for the considered channel and phase-noise models. Numerical results validate the analytical expressions, and highlight the effects of different system parameters on the achievable rate. O…
This paper proposes a novel approach to improve the performance of a heterogeneous network (HetNet) supported by dual connectivity (DC) by adopting multiple unmanned aerial vehicles (UAVs) as passive relays that carry reconfigurable intelligent surfaces (RISs). More specifically, RISs are deployed under the UAVs termed as UAVs-RISs that operate over the micro-wave ($μ$W) channel in the sky to sustain a strong line-of-sight (LoS) connection with the ground users. The macro-cell operates over the $μ$W channel based on orthogonal multiple access (OMA), while small base stations (SBSs) operate ove…
We investigate a multi-user multiple-input multiple-output interference network in the presence of multiple reconfigurable intelligent surfaces (RISs). The entire system is described by using a circuit-based model for the transmitters, receivers, and RISs. This is obtained by leveraging the electromagnetic tool of mutual impedances, which accounts for the signal propagation and the mutual coupling among closely-spaced scattering elements. An iterative and provably convergent optimization algorithm that maximizes the sum-rate of RIS-assisted multi-user interference channels is introduced. Numer…
In this paper, we investigate network-assisted full-duplex (NAFD) cell-free millimeter-wave (mmWave) massive multiple-input multiple-output (MIMO) systems with digital-to-analog converter (DAC) quantization and fronthaul compression. We propose to maximize the weighted uplink and downlink sum rate by jointly optimizing the power allocation of both the transmitting remote antenna units (T-RAUs) and uplink users and the variances of the downlink and uplink fronthaul compression noises. To deal with this challenging problem, we further apply a successive convex approximation (SCA) method to handl…
We consider a system that integrates positioning and single-user millimeter wave (mmWave) communication, where the communication part adopts wavelength division multiplexing (WDM) and orbital angular momentum (OAM). This paper addresses the multi-dimensional constellation design in shortrange line-of-sight (LOS) environment, with stable communication links. We propose a map-assisted method to quantify the system parameters based on positions and reduce real-time computing overhead. We explore the possibility of using a few patterns in the maps, and investigate its performance loss. We first in…
Channel reciprocity greatly facilitates downlink precoding in time-division duplexing (TDD) multiple-input multiple-output (MIMO) communications without the need for channel state information (CSI) feedback. Recently, reconfigurable intelligent surfaces (RISs) emerge as a promising technology to enhance the performance of future wireless networks. However, since the artificial electromagnetic characteristics of RISs do not strictly follow the normal laws of nature, it brings up a question: does the channel reciprocity hold in RIS-assisted TDD wireless networks? After briefly reviewing the reci…
Reconfigurable intelligent surfaces (RISs) have attracted great attention as a potential beyond 5G technology. These surfaces consist of many passive elements of metamaterials whose impedance can be controllable to change the phase, amplitude, or other characteristics of wireless signals impinging on them. Channel estimation is a critical task when it comes to the control of a large RIS when having a channel with a large number of multipath components. In this paper, we propose a novel channel estimation scheme that exploits spatial correlation characteristics at both the massive multiple-inpu…
This paper proposes to deploy multiple reconfigurable intelligent surfaces (RISs) in device-to-device (D2D)-underlaid cellular systems. The uplink sum-rate of the system is maximized by jointly optimizing the transmit powers of the users, the pairing of the cellular users (CUs) and D2D links, the receive beamforming of the base station (BS), and the configuration of the RISs, subject to the power limits and quality-of-service (QoS) of the users. To address the non-convexity of this problem, we develop a new block coordinate descent (BCD) framework which decouples the D2D-CU pairing, power allo…
Queen Mary University of London（伦敦玛丽女王大学）；Ireland Research Center, Huawei Technologies（华为技术有限公司爱尔兰研究中心）
Coverage and capacity are the important metrics for performance evaluation in wireless networks, while the coverage and capacity have several conflicting relationships, e.g. high transmit power contributes to large coverage but high inter-cell interference reduces the capacity performance. Therefore, in order to strike a balance between the coverage and capacity, a novel model is proposed for the coverage and capacity optimization of simultaneously transmitting and reflecting reconfigurable intelligent surfaces (STAR-RISs) assisted networks. To solve the coverage and capacity optimization (CCO…
Reconfigurable intelligent surfaces (RISs), with the potential to realize a smart radio environment, have emerged as an energy-efficient and a cost-effective technology to support the services and demands foreseen for coming decades. By leveraging a large number of low-cost passive reflecting elements, RISs introduce a phase-shift in the impinging signal to create a favorable propagation channel between the transmitter and the receiver.~\textcolor{black}{In this article, we provide a tutorial overview of RISs for sixth-generation (6G) wireless networks. Specifically, we present a comprehensive…
Unmanned aerial vehicles (UAVs) have brought a lot of flexibility in the network deployment. However, UAVs suffer from the high mobility and instability. To improve the capacity and reliability of the UAV networks, millimeter-wave (mmWave) and reconfigurable intelligent surfaces (RISs) can be used in the system. In this paper, we consider an RIS-assisted mmWave UAV wireless cellular network, where UAVs serve several users with the help of multiple RISs. We jointly optimize the deployment, user scheduling, beamforming vector, and RIS phases to maximize the sum-rate, with the constraints of the …
This work investigates the effect of double intelligent reflecting surface (IRS) in improving the spectrum efficient of multi-user multiple-input multiple-output (MIMO) network operating in the millimeter wave (mmWave) band. Specifically, we aim to solve a weighted sum rate maximization problem by jointly optimizing the digital precoding at the transmitter and the analog phase shifters at the IRS, subject to the minimum achievable rate constraint. To facilitate the design of an efficient solution, we first reformulate the original problem into a tractable one by exploiting the majorization-min…
Reconfigurable intelligent surfaces (RISs) can establish favorable wireless environments to combat the severe attenuation and blockages in millimeter-wave (mmWave) bands. However, to achieve the optimal enhancement of performance, the instantaneous channel state information (CSI) needs to be estimated at the cost of a large overhead that scales with the number of RIS elements and the number of users. In this paper, we design a quasi-static broad coverage at the RIS with the reduced overhead based on the statistical CSI. We propose a design framework to synthesize the power pattern reflected by…
Beijing Institute of Technology（北京理工大学）；CNRS（法国国家科学研究中心）；CentraleSupélec（中央理工-高等电力学院）；Université Paris-Saclay（巴黎-萨克雷大学）；King Abdullah University of Science and Technology（阿卜杜拉国王科技大学）
Integrating large intelligent reflecting surfaces (IRS) into millimeter-wave (mmWave) massive multi-input-multi-ouput (MIMO) has been a promising approach for improved coverage and throughput. Most existing work assumes the ideal channel estimation, which can be challenging due to the high-dimensional cascaded MIMO channels and passive reflecting elements. Therefore, this paper proposes a deep denoising neural network assisted compressive channel estimation for mmWave IRS systems to reduce the training overhead. Specifically, we first introduce a hybrid passive/active IRS architecture, where v…
A Stochastic Geometry Framework for Performance Analysis of RIS-assisted OFDM Cellular Networks
Institut national de recherche en sciences et technologies du numérique (INRIA)（法国国家数字研究学院）；Ecole Normale Supérieure（巴黎高等师范学院）；Nokia Networks France（诺基亚法国网络）
This paper investigates two performance metrics, namely ergodic capacity and symbol error rate, of mmWave communication system assisted by a reconfigurable intelligent surface (RIS). We assume independent and identically distributed (i.i.d.) Rician fadings between user-RIS-Access Point (AP), with RIS surface consisting of passive reflecting elements. First, we derive a new unified closed-form formula for the average symbol error probability of generalised M-QAM/M-PSK signalling over this mmWave link. We then obtain new closed-form expressions for the ergodic capacity with and without channel s…
In this paper, the optimization of deploying unmanned aerial vehicles (UAVs) over a reconfigurable intelligent surfaces (RISs)-assisted visible light communication (VLC) system is studied. In the considered model, UAVs are required to simultaneously provide wireless services as well as illumination for ground users. To meet the traffic and illumination demands of the ground users while minimizing the energy consumption of the UAVs, one must optimize UAV deployment, phase shift of RISs, user association and RIS association. This problem is formulated as an optimization problem whose goal is to …
Reconfigurable intelligent surfaces (RISs) comprised of tunable unit cells have recently drawn significant attention due to their superior capability in manipulating electromagnetic waves. In particular, RIS-assisted wireless communications have the great potential to achieve significant performance improvement and coverage enhancement in a cost-effective and energy-efficient manner, by properly programming the reflection coefficients of the unit cells of RISs. In this paper, free-space path loss models for RIS-assisted wireless communications are developed for different scenarios by studying …
Cognitive radio networks (CRNs) and millimeter wave (mmWave) communications are two major technologies to enhance the spectrum efficiency (SE). Considering that the SE improvement in the CRNs is limited due to the interference temperature imposed on the primary user (PU), and the severe path loss and high directivity in mmWave communications make it vulnerable to blockage events, we introduce an intelligent reflecting surface (IRS) into mmWave CRNs. Due to the estimation mismatch and the passivity of Eavesdroppers (Eves), perfect channel state information (CSI) of wiretap links is challenging …
