Exploring the nanoscale origin of performance enhancement in Li$_{1.1}$Ni$_{0.35}$Mn$_{0.55}$O$_2$ batteries due to chemical doping
Thomas Thersleff, Jordi Jacas Biendicho, Kunkanadu Prakasha, Elias Martinez Moreno, Leif Olav Jøsang, Jekabs Grins, Aleksander Jaworski, Gunnar Svensson
Despite significant potential as energy storage materials for electric vehicles due to their combination of high energy density per unit cost and reduced environmental and ethical concerns, Co-free lithium ion batteries based off layered Mn oxides presently lack the longevity and stability of their Co-containing counterparts. Here, we demonstrate a reduction in this performance gap via chemical doping, with Li$_{1.1}$Ni$_{0.35}$Mn$_{0.55}$O$_2$ achieving an initial discharge capacity of 159 mAhg$^{-1}$ at C/3 rate and a corresponding capacity retention of 94.3% after 150 cycles. We subsequently explore the nanoscale origins of this improvement through a combination of advanced diffraction, spectroscopy, and electron microscopy techniques, finding that optimized doping profiles lead to an improved structural and chemical compatibility between the two constituent sub-phases that characterize the layered Mn oxide system, resulting in the formation of unobstructed lithium ion pathways between them. We also directly observe a structural stabilization effect of the host compound near the surface using aberration corrected scanning transmission electron microscopy and integrated differential phase contrast imaging.
Finding proper electrocatalysts capable of efficient catalyzing both ORR and OER is of great importance for metal-air batteries. With increasing inclination towards structural and flexible devices, developing a high-performance self-standing air-cathode is highly demanded and challenging, as most of oxygen catalysts are powder and need to be further processed. Here, we construct highly bifunctional air catalyst from macroscopic CNT fibers (CNTf) through direct CVD spinning followed by hydrothermal method. The electrocatalytic properties of the samples were tuned by altering nitrogen-doping and…
Interfaces are ubiquitous in Li-ion battery electrodes, occurring across compositional gradients, regions of multiphase intergrowths, and between electrodes and solid electrolyte interphases or protective coatings. However, the impact of these interfaces on Li energetics remains largely unknown. In this work, we calculated Li intercalation-site energetics across cathode interfaces and demonstrated the physics governing these energetics on both sides of the interface. We studied the olivine/olivine-structured LixFePO4/LixMPO4 (x=0 and 1, M=Co, Ti, Mn) and layered/layered-structured LiNiO2/TiO2 …
Nanoscale imaging reveals critical plating and stripping mechanisms in anode-free lithium and sodium solid-state batteries
Autonomous University of Madrid (UAM)（马德里自治大学）；Nicolás Cabrera University Institute of Materials Science (INC), UAM（尼古拉斯·卡布雷拉大学材料科学研究院（INC））；ALBA Synchrotron Light Facility（阿尔巴同步辐射光源设施）；Norwegian University of Science and Technology (NTNU)（挪威科技大学）；Fraunhofer Institute for Ceramic Technologies and Systems (IKTS)（弗劳恩霍夫陶瓷技术和系统研究所）；Instituto de Ciencia de Materiales de Madrid, Consejo Superior de Investigaciones Científicas (CSIC)（马德里材料科学研究所，西班牙国家研究委员会）；National Institute of Advanced Industrial Science and Technology (AIST), Research Institute for Energy Efficient Technologies（国立先进工业科学技术研究院，能源效率技术研究所）；Condensed Matter Physics Center (IFIMAC), UAM（凝聚态物理中心（IFIMAC））
All-solid-state lithium batteries promise significant improvements in energy density and safety over traditional liquid electrolyte batteries. The Al-doped AlxLi7-3xLa3Zr2O12 (LLZO) solid-state electrolyte shows excellent potential given its high ionic conductivity and good thermal, chemical, and electrochemical stability. Nevertheless, further improvements on LLZOs electrochemical and mechanical properties call for an incisive understanding of its local microstructure. Here, we employ Bragg Coherent Diffractive Imaging to investigate the atomic displacements inside single grains of LLZO with …
Using field-emission resonance spectroscopy with an ultrahigh vacuum scanning tunneling microscope, we reveal Stark-shifted image-potential states of the v_1/6 and v_1/5 borophene polymorphs on Ag(111) with long lifetimes, suggesting high borophene lattice and interface quality. These image-potential states allow the local work function and interfacial charge transfer of borophene to be probed at the nanoscale and test the widely employed self-doping model of borophene. Supported by apparent barrier height measurements and density functional theory calculations, electron transfer doping occurs…
We use confocal Raman microscopy and modified vector analysis methods to investigate the nanoscale origin of strain and carrier concentration in exfoliated graphene-hexagonal boron nitride (hBN) heterostructures on silicon dioxide (SiO2). Two types of heterostructures are studied: graphene on SiO2 partially coved by hBN, and graphene fully encapsulated between two hBN flakes. We extend the vector analysis methods to produce spatial maps of the strain and doping variation across the heterostructures. This allows us to visualise and directly quantify the much-speculated effect of the environment…
All electronic, optoelectronic or photovoltaic applications of silicon depend on controlling majority charge carriers via doping with impurity atoms. Nanoscale silicon is omnipresent in fundamental research (quantum dots, nanowires) but also approached in future technology nodes of the microelectronics industry. In general, silicon nanovolumes, irrespective of their intended purpose, suffer from effects that impede conventional doping due to fundamental physical principles such as out-diffusion, statistics of small numbers, quantum- or dielectric confinement. In analogy to the concept of modul…
The highest temperature superconductors are electronically inhomogeneous at the nanoscale, suggesting the existence of a local variable which could be harnessed to enhance the superconducting pairing. Here we report the relationship between local doping and local strain in the cuprate superconductor Bi$_2$Sr$_2$CaCu$_2$O$_{8+x}$. We use scanning tunneling microscopy to discover that the crucial oxygen dopants are periodically distributed, in correlation with local strain. Our picoscale investigation of the intra-unit-cell positions of all oxygen dopants provides essential structural input for …
Doping inhomogeneities in solids are not uncommon, but their microscopic observation and understanding are limited due to the lack of bulk-sensitive experimental techniques with high-enough spatial and spectral resolution. Here, we demonstrate nanoscale imaging of both dopants and free charge carriers in La-doped BaSnO3 (BLSO) using high-resolution electron energy-loss spectroscopy (EELS). By analyzing both high- and low-energy excitations in EELS, we reveal chemical and electronic inhomogeneities within a single BLSO nanocrystal. The inhomogeneous doping leads to distinctive localized infrare…
New electrode materials for alkaline-ion batteries are a timely topic. Among many promising candidates, V2O5 is one of the most interesting cathode materials. While having very high theoretical capacity, in practice, its performance is hindered by low stability and poor conductivity. As regards theoretical descriptions of V2O5, common DFT-GGA calculations fail to reproduce both the electronic and crystal structure. While the band gap is underestimated, the interlayer spacing is overestimated as weak dispersion interactions are not properly described within GGA. Here we show that the combinatio…
Here, we correlate the nanoscale morphology and chemical composition of solid electrolyte interphases (SEI) with the electrochemical property of graphite-based composite electrodes. Using electrochemical strain microscopy (ESM) and X-ray photoelectron spectroscopy (XPS), changes of chemical composition and morphology (Li and F distribution) in SEI layers on the electrodes as a function of solid electrolyte contents are analyzed. As a result, we find a strong correlation between morphological variations on the electrode, Li and F distribution in SEI layer, and Coulomb efficiency. This correlati…
Improved Electrochemical Performance and Diffusion kinetics by Boron-doping in Na$_{0.66}$Mn$_{0.8}$Fe$_{0.2}$O$_{2}$ Layered Cathodes for Sodium-Ion Batteries
Indian Institute of Technology Delhi（印度德里理工学院）；Hindu College, University of Delhi（德里大学印度教学院）；Indian Institute of Technology Delhi-Abu Dhabi（印度德里理工学院阿布扎比分校）
We propose a unique way to control both bandgap and the magnetic properties of nanoscale graphene, which might prove highly beneficial for application in nanoelectronic and spintronic devices. We have shown that chemical doping by nitrogen along a single zigzag edge breaks the sublattice symmetry of graphene. This leads to the opening of a gap and a shift of the molecular orbitals localized on the doped edge in such a way that the spin gap asymmetry, which can lead to half-metallicity under certain conditions, is obtained. The spin-selective behavior of graphene and tunable spin gaps help us t…
We report on \textit{ab initio} electronic structure simulations of Li$_2$O$_2$, where 1.6% of lithium atoms are substituted by silicon. It is demonstrated that this leads to the formation of conducting impurity states in the band gap of Li$_2$O$_2$. We show that these states originate from the antibonding orbitals of the oxygen pairs and are remarkably stable against possible polaron formation (upon electron injection). Through this polaron preemption mechanism, the proposed compound is expected to show significantly higher electronic mobility than stoichiometric Li$_2$O$_2$, which could have…
While Si is an effective insertion type anode for Li-ion batteries, crystalline Si has been shown to be unsuitable for Na and Mg storage due, in particular, to insufficient binding strength. It has recently been reported that Si nanowires could be synthesized with high-concentration (several atomic %) and dispersed Al doping. Here we show based on density functional theory calculations that Al doping significantly improves the energetics for Na and Mg insertion, specifically, making it thermodynamically favored versus vacuum reference states. For high Al concentrations, the energy of Mg in Al-…
Several effective methods have been developed recently to demonstrate simultaneous high energy and high power density in Li - carbon fluoride (CF$_x$) batteries. These methods can achieve as high as 1000 Wh/kg energy density at 60-70 kW/kg power density (40-50 C rate) in coin cells and 750 Wh/kg energy density at 12.5 kW/kg power density (20 C rate) in pouch cells. This performance is made possible by ingenious nano-architecture design, controlled porosity, boron doping and electrolyte additives. In the present study, we show that a similarly great performance, 931 Wh/kg energy density at 59 k…
Strong correlated manganites are still under intense research owing to their complex phase diagrams in terms of the Sr-doping and their sensitivity to intrinsic and extrinsic structural deformations. Here, we performed x-ray absorption spectroscopy measurements of manganites bilayers to explore the effects that a local Sr-doping gradient produce on the charge and antiferromagnetic anisotropies. In order to gradually tune the Sr-doping level along the axis perpendicular to the samples we have grown a series of bilayers with different thicknesses of low-doped manganites (from 0 nm to 6 nm) depos…
Compact solid discharge products enable energy storage devices with high gravimetric and volumetric energy densities, but solid deposits on active surfaces can disturb charge transport and induce mechanical stress. In this Letter we develop a nanoscale continuum model for the growth of Li2O2 crystals in lithium-oxygen batteries with organic electrolytes, based on a theory of electrochemical non-equilibrium thermodynamics originally applied to Li-ion batteries. As in the case of lithium insertion in phase-separating LiFePO4 nanoparticles, the theory predicts a transition from complex to uniform…
Effective passivation of lithium metal surfaces, and prevention of battery-shorting lithium dendrite growth, are critical for implementing lithium-metal-anodes for batteries with increased power densities. Nanoscale surface heterogeneities can be "hot spots" where anode passivation breaks down. Motivated by the observation of lithium dendrites in pores and grain boundaries in all-solid batteries, we examine lithium metal surfaces covered with Li(2)O and/or LiF thin films with grain boundaries in them. Electronic structure calculations show that, at >0.25 V computed equilibrium overpotential, L…
Supercapacitors have recently gained popularity as possible energy storage systems due to their high cycling ability and increased power density. However, one of the major drawbacks of supercapacitors is that they have a low energy density, which makes them less effective than batteries. Herein, we explore different methods of increasing the supercapacitor performance of the perovskite SrCoO3. We carry out first-principles calculations to systematically study how SrCoO3/graphene interface, oxygen vacancies, and doping improve the performance of strontium cobaltite as an anion-intercalation-typ…
We demonstrate single dopant implantation into the channel of a silicon nanoscale metal-oxide-semiconductor field-effect-transistor. This is achieved by monitoring the drain current modulation during ion irradiation. Deterministic doping is crucial for overcoming dopant number variability in present nanoscale devices and for exploiting single atom degrees of freedom. The two main ion stopping processes that induce drain current modulation are examined. We employ 500~keV He ions, in which electronic stopping is dominant, leading to discrete increases in drain current and 14~keV P dopants for wh…
"Secondary doping" in poly(3,4-ethylenedioxy-thiophene):poly(styrenesulfonate) (PEDOT:PSS) is quite effective and a frequently used method for the conductivity enhancement. This simple approach, the addition of co-solvents to the PEDOT:PSS solution before film fabrication, is an essential way to derive the high electrical performance of PEDOT:PSS, but the mechanism still remains unclear. In this study, nanoscale structural changes synchronized with the conductivity enhancement via secondary doping in PEDOT:PSS films were investigated. During secondary doping with ethylene glycol near the criti…
Natural abundance, impressive chemical characteristics and economic feasibility have rekindled the appeal for rechargeable sodium (Na) batteries as a practical solution for the growing energy demand, environmental sustainability and energy independence. However, the scarcity of viable positive electrode materials remains a huge impediment to the actualization of this technology. In this paper, we explore honeycomb layered oxides adopting the composition Na$_2$Ni$_{2-x}$Co$_x$TeO$_6$ ($x = 0, 0.25$ and $0.50$) as feasible positive electrode (cathode) materials for rechargeable sodium batteries …
Fullerene-based materials including C60 and doped C60 have previously been proposed as anodes for lithium ion batteries. It was also shown earlier that n- and p-doping of small molecules can substantially increase voltages and specific capacities. Here, we study ab initio the attachment of multiple lithium atoms to C60, nitrogen-doped C60 (n-type), and boron doped C60 (p-type). We relate the observed attachment energies (which determine the voltage) to changes in the electronic structure induced by Li attachment and by doping. We compare results with a GGA functional and a hybrid functional an…
Endowed with a multitude of exquisite properties such as rich electrochemistry, superb topology and eccentric electromagnetic phenomena, honeycomb layered oxides have risen to the top echelons of science with applications in diverse fields ranging from condensed matter physics, solid-state chemistry, materials science, solid-state ionics to electrochemistry. However, these oxides are vastly underutilised as their underlying atomistic mechanisms remain unexplored. Therefore, in this study, atomic-resolution imaging on pristine $\rm K_2Ni_2TeO_6$ along multiple zone axes was conducted using sphe…
Synergetic Enhancement on Bulk and Grain Boundary Ionic Conduction of Mg Doped High-Entropy NASICON-Type Solid Electrolyte for Solid-State Na+ Batteries by Spray Flame Synthesis
The diversified essential properties of the stage-n graphite alkali-intercalation compounds are thoroughly explored by the first-principles calculations. According to their main features, the lithium and non-lithium materials might be quite different from each other in stacking configurations, the intercalated alkali-atom concentrations, the free conduction electron densities, and the atom-dominated & (carbon, alkali)-co-dominated energy bands. The close relations between the alkali-doped metallic behaviors and the geometric symmetries will be clarified through the interlayer atomic interactio…
$Ab$ $initio$ Study of Substitutional Defects in Li$_{3}$OCl Solid Electrolyte for Li-ion Batteries
University of Missouri Research Reactor, University of Missouri（密苏里大学研究反应堆，密苏里大学）；Department of Physics and Astronomy, University of Missouri（密苏里大学物理与天文学系）；Materials Science and Engineering Institute, University of Missouri（密苏里大学材料科学与工程研究所）；Department of Chemical and Biomedical Engineering, University of Missouri（密苏里大学化学与生物医学工程系）
V$_{2}$O$_{5}$ in its $ω$ phase (Li$_{3}$V$_{2}$O$_{5}$) with excess lithium is a potential alternative to the graphite anode for lithium-ion batteries at low temperature and fast charging conditions due to its safer voltage (0.6 V vs Li$^{+}$/Li(s)) and high lithium transport rate. In-operando cationic disorder, as observed in most ordered materials, can produce significant changes in charge compensation mechanisms, anionic activity, lithium diffusion and operational voltages. In this work, we report the variation in structural distortion, electronic structure and migration barrier accompanie…
Downsizing well-established materials to the nanoscale is a key route to novel functionalities, in particular if different functionalities are merged in hybrid nanomaterials. Hybrid carbon-based hierarchical nanostructures are particularly promising for electrochemical energy storage since they combine benefits of nanosize effects, enhanced electrical conductivity and integrity of bulk materials. We show that endohedral multiwalled carbon nanotubes (CNT) encapsulating high-capacity (here: conversion and alloying) electrode materials have a high potential for use in anode materials for lithium-…
Oxide materials offer a wide range of interesting physical and chemical properties. Even more versatile behavior of oxides is seen at the nanoscale, qualifying these materials for a number of applications. In this study we used DFT calculations to investigate the physical and chemical properties of small hexagonal MgO nanotubes of different length. We analyzed the effect of Li, B, C, N, and F doping on the properties of the nanotubes. We find that all dopants favor the edge positions when, incorporated into the nanotubes. Doping results in the net magnetization whose value depends on the type …
The ferroelectric properties of nanoscale silicon doped HfO$_2$ promise a multitude of applications ranging from ferroelectric memory to energy-related applications. The reason for the unexpected behavior has not been clearly proven and presumably include contributions from size effects and doping effects. Silicon incorporation in HfO$_2$ is investigated computationally by first-principles using different density functional theory (DFT) methods. Formation energies of interstitial and substitutional silicon in HfO$_2$ paired with and without an oxygen vacancy prove the substitutional defect as …
Attaining low resistivity AlGaN layers is the keystone to improve the efficiency of light emitting devices in the ultraviolet spectral range. Here, we present a microstructural analysis of Ge-doped AlGaN samples with Al mole fraction from x=0 to 1, and nominal doping level in the range of 1E20 cm-3, together with the measurement of Ge concentration and its spatial distribution down to the nm scale. AlGaN:Ge samples with x smaller or equal to 0.2 do not present any sign of inhomogeneity. However, samples with x > 0.4 display micrometer-size Ge crystallites at the surface. Ge segregation is not …
Doping of substrates at desired locations is a key technology for spin-based quantum memory devices. Focused ion beam implantation is well-suited for this task due to its high spacial resolution. In this work, we investigate ion-beam implanted erbium ensembles in Yttrium Orthosilicate crystals by means of confocal photoluminescence spectroscopy. The sample temperature and the post-implantation annealing step strongly reverberate in the properties of the implanted ions. We find that hot implantation leads to a higher activation rate of the ions. At high enough fluences, the relation between the…
Pristine graphene interacts relatively weakly with Al, which is a specie of importance for novel generations of metal-ion batteries. We employ DFT calculations to explore the possibility of enhancing Al interaction with graphene. We investigate non-doped and N-doped graphene nanoribbons, address the impact of the edge sites, which are always present to some extent in real samples, and N-containing defects on the material's reactivity towards Al. The results are compared to that of pristine graphene. We show that introduction of edges does not affect the energetics of Al adsorption significantl…
We report the electrochemical investigation of 5% Al doped MoS$_2$@rGO composite as a high-performance anode for sodium (Na)-ion batteries. The x-ray diffraction (XRD), Raman spectroscopy and high-resolution transmission electron microscopy characterizations reveal that the Al doping increase the interlayer spacing of (002) plane of MoS$_2$ nanosheets and form a stable 1T phase. The galvanostatic charge-discharge measurements show the specific capacity stable around 450, 400, 350, 300 and 200 mAhg$^{-1}$ at current densities of 0.05, 0.1, 0.3, 0.5 and 1~Ag$^{-1}$, respectively. Also, we observ…
Unraveling the storage mechanism of Na$_{3}$V$_{2-x}$Ni$_x$(PO$_4$)$_2$F$_3$/C cathodes for sodium-ion batteries through electrochemical, {\it operando} X-ray diffraction and microscopy studies
本研究结合 EIS、GITT、CV、operando XRD 与原位同步辐射 TXM，揭示 Ni 掺杂 Na₃V₂(PO₄)₂F₃/C 正极的储钠机制、扩散动力学及长循环稳定性。
Inspired by a recent experimental and theoretical study [Yang et al., 2017], wherein protrusions in graphene have been proposed as an effective strategy to enhance the performance of sodium ion batteries, a comprehensive study of the effects of phosphorus doping in graphene on adsorption and diffusion behaviour of Li is carried out by using density functional theory. We find that protrusion introduced by P-dopant in graphene enhances the adsorption of a single Li atom onto the anode due to an additional partial covalent bonding character between Li and carbon atoms of the substrate. However, w…
Bismuth chalcogenides and lead telluride/selenide alloys exhibit exceptional thermoelectric properties which could be harnessed for power generation and device applications. Since phonons play a significant role in achieving these desired properties, quantifying the interaction between phonons and electrons, which is encoded in the Eliashberg function of a material, is of immense importance. However, its precise extraction has in part been limited due to the lack of local experimental probes. Here we construct a method to directly extract the Eliashberg function using Landau level spectroscopy…
Nanoscale resistive switching in electrodeposited MOF Prussian blue analogs driven by K-ion intercalation probed by C-AFM
Université catholique de Louvain (UCLouvain)（天主教鲁汶大学）；University of Applied Sciences Zwickau（茨维考应用技术大学）；Universidad de Granada（格拉纳达大学）；Universitat de Valencia（瓦伦西亚大学）
We report on the electrical characterisation of a series of thin chromium oxide films, grown by dc sputtering, to evaluate their suitability for use as on-chip resistors in nanoelectronics. By increasing the level of oxygen doping, the room-temperature sheet resistance of the chromium oxide films was varied from 28$Ω/ \square$ to 32.6k$Ω/ \square$. The variation in resistance with cooling to 4.2K in liquid helium was investigated; the sheet resistance at 4.2K varied with composition from 65$Ω/ \square$ to above 20G$Ω/ \square$. All of the films measured displayed ohmic behaviour at all measure…
