Microresonator frequency combs based on the $χ^{(3)}$ nonlinearity are nowadays well understood and making their way into different applications. Recently, microresonator frequency combs based on the $χ^{(2)}$ nonlinearity are receiving increasing attention, as they promise certain benefits, but still require further study. Here, we demonstrate the generation of a $χ^{(2)}$ frequency comb, initiated via optical parametric oscillation (OPO) in a lithium niobate mm-sized microresonator. By pumping at 532 nm with 30 $μ$W of power, we observe 1-THz-wide comb spectra around 1064 nm with degenerate and non-degenerate states. We also show that comb generation requires signal and idler waves to be degenerate in mode numbers and how the fulfillment of this condition can be identified from the temperature tuning curves. The results demonstrate the potential to directly generate frequency combs via OPO beyond 3 $μ$m wavelengths in the mid-IR by puming in the near-IR region.
We demonstrate electro-optic tuning of an on-chip lithium niobate microresonator with integrated in-plane microelectrodes. First two metallic microelectrodes on the substrate were formed via femtosecond laser process. Then a high-Q lithium niobate microresonator located between the microelectrodes was fabricated by femtosecond laser direct writing accompanied by focused ion beam milling. Due to the efficient structure designing, high electro-optical tuning coefficient of 3.41 pm/V was observed.
We report on fabrication of high Q lithium niobate (LN) whispering-gallery-mode (WGM) microresonators suspended on silica pedestals by femtosecond laser microfabrication. The micrometer-scale (diameter ~82 μm) LN resonator possesses a Q factor of 2.5x10^5 around 1550 nm wavelength range. Moreover, second harmonic generation with a continuous-wave tunable single-longitudinal-mode pump laser in the on-chip LN microresonator is demonstrated in the on-chip LN microresonator. A fiber taper is employed to couple the pump laser into the microresonator, showing a normalized conversion efficiency of 1.…
We demonstrate integrating a high quality factor lithium niobate microdisk resonator with a free-standing membrane waveguide. Our technique is based on femtosecond laser direct writing which produces the pre-structure, followed by focused ion beam milling which reduces the surface roughness of sidewall of the fabricated structure to nanometer scale. Efficient light coupling between the integrated waveguide and microdisk was achieved, and the quality factor of the microresonator was measured as high as 1.67*10^5.
Nonlinear optical processes in whispering gallery mode (WGM) microresonators have attracted much attention. Owing to the strong confinement of light in a small volume, a WGM microresonator can dramatically boost the strength of light field, thereby promoting the nonlinear interaction between the light and the resonator material. However, realization of efficient nonlinear parametric process in microresonators is a challenging issue. The major difficulty is to simultaneously ensure the phase matching condition and a coherent multiple resonance condition for all the waves participating in the no…
We demonstrate efficient second harmonic generation in a quasi-phase-matched, high quality factor ($Q_0 \approx 5.3\times 10^5$) racetrack microresonator. The observed normalized conversion efficiency is about $3.8\%~mW^{-1}$.
Tunable light sources are a key enabling technology for many applications such as ranging, spectroscopy, optical coherence tomography, digital imaging and interferometry. For miniaturized laser devices, whispering gallery resonator lasers are a well-suited platform, offering low thresholds and small linewidths, however, many realizations suffer from the lack of reliable tuning. Rare-earth ion-doped lithium niobate offers a way to solve this issue. Here we present a single-frequency laser based on a neodymium-doped lithium niobate whispering gallery mode resonator that is tuned via the linear e…
The recent advancement in lithium niobate on insulator (LNOI) technology is revolutionizing the optoelectronic industry as devices of higher performance, lower power consumption, and smaller footprint can be realized due to the high optical confinement in the structures. The LNOI platform offers both large \c{hi}(2) and \c{hi}(3) nonlinearities along with the power of dispersion engineering, enabling brand new nonlinear photonic devices and applications towards the next generation of integrated photonic circuits. However, the Raman scattering, one of the most important nonlinear phenomena, hav…
Nonlinear optics in whispering-gallery-mode (WGM) microresonators have attracted much attention. Owing to strong confinement of the light in a small volume, a WGM microresonator can dramatically boost the strength of light field, giving rise to enhancement of the nonlinear interactions of light with the resonator material. Here, we demonstrate highly efficient second harmonic generation (SHG) and third harmonic generation (THG) in an on-chip monocrystalline lithium niobate (LN) microresonator. Benefitting from a cyclic phase matching scheme for the transverse-electric WGMs, nonlinear wavelengt…
Eigenfrequency tuning in microresonators is useful for a range of applications including frequency-agile optical filters and tunable optical frequency converters. In most of these applications, eigenfrequency tuning is achieved by thermal or mechanical means, while a few non-centrosymmetric crystals such as lithium niobate allow for such tuning using the linear electro-optic effect. Potassium tantalate-niobate ($\mathrm{KTa}_{1-x}\mathrm{Nb}_{x}\mathrm{O}_{3}$ with $0\leq x \leq1$, KTN) is a particularly attractive material for electro-optic tuning purposes. It has both non-centrosymmetric and…
We report on the experimental observation of internally-pumped parametric oscillation in a high-Q lithium niobate microresonator under conditions of natural phase-matching. Specifically, launching near-infrared pump light around 1060 nm into a $z$-cut congruent lithium niobate microresonator, we observe the generation of optical sidebands around the input pump under conditions where second-harmonic generation is close to natural phase-matching. We find that a wide range of different sideband frequency shifts can be generated by varying the experimental parameters. Under particular conditions, …
On-chip bright quantum sources with multiplexing ability are extremely high in demand for the integrated quantum networks with unprecedented scalability and complexity. Here, we demonstrate an ultrabright and broadband biphoton quantum source generated in a lithium niobate microresonator system.Without introducing the conventional domain poling, the on-chip microdisk produces entangled photon pairs covering a broad bandwidth promised by natural phase matching in spontaneous parametric down conversion.Experimentally, the multiplexed photon pairs are characterized by $30\ \rm nm$ bandwidth limit…
Adiabatic frequency conversion has some key advantages over nonlinear frequency conversion. No threshold and no phase-matching conditions need to be fulfilled. Moreover, it exhibits a conversion efficiency of $100\,\%$ down to the single-photon level. Adiabatic frequency conversion schemes in microresonators demonstrated so far suffer either from low quality factors of the employed resonators resulting in short photon lifetimes or small frequency shifts. Here, we present an adiabatic frequency conversion (AFC) scheme by employing the Pockels effect. We use a non-centrosymmetric ultrahigh-$Q$ m…
High quality lithium niobate thin film microresonators provide an ideal platform for on-chip nonlinear optics applications. However, the phase matching condition for efficient parametric process sets a high requirement for fabrication control. Here we demonstrate a photonic molecular structure composed of two strongly coupled lithium niobate microdisks of different diameters fabricated using femtosecond laser micromachining and focused ion beam milling. With a continuous wave excitation, rich nonlinear optical processes including cascaded four-wave mixing and stimulated Raman scattering were o…
Owing to the discrete frequency spectrum of whispering gallery resonators (WGRs), the resonance and phase-matching conditions for the interacting waves in the case of second-harmonic generation (SHG) cannot generally be fulfilled simultaneously. To account for this, we develop a model describing SHG in WGRs with non-zero frequency detunings at both the pump and second-harmonic frequencies. Our model predicts strong distortions of the line shape of pump and second-harmonic resonances for similar linewidths at both frequencies; for much larger linewidths at the second-harmonic frequency, this be…
We investigate the threshold of $χ^{(2)}$ frequency comb generation in lithium niobate whispering gallery microresonators theoretically and experimentally. When generating a frequency comb via second-harmonic generation, the threshold for the onset of cascaded second-order processes leading to a comb is found to be approximately 85 $μ$W. The second-harmonic generation efficiency up to this value is in excellent agreement with a previously known theoretical framework. This framework is extended here, showing that the onset of cascaded $χ^{(2)}$ processes and the maximum of the second-harmonic g…
Optical microresonators have recently attracted a growing attention in the photonics community. Their applications range from quantum electro-dynamics to sensors and filtering devices for optical telecommunication systems, where they are likely to become an essential building block. The integration of nonlinear and electro-optical properties in the resonators represents a very stimulating challenge, as it would incorporate new and more advanced functionality. Lithium niobate is an excellent candidate material, being an established choice for electro-optic and nonlinear optical applications. He…
We observe high optical quality factor (Q) polygonal and star coherent optical modes in a lithium niobate microdisk. In contrast to the previous polygon modes achieved by deformed microcavities at lower mechanical and optical Q, we adopted weak perturbation from a tapered fiber for the polygon mode formation. The resulting high intracavity optical power of the polygon modes triggers second harmonic generation at high efficiency. With the combined advantage of high mechanical Q cavity optomechanical oscillation was observed for the first time. Finally, we observe frequency microcomb generation …
We report on fabrication of crystalline lithium niobate microresonators with quality factors above 10^7 as measured around 770 nm wavelength. Our technique relies on femtosecond laser micromachining for patterning a mask coated on the lithium niobate on insulate (LNOI) into a microdisk, followed by a chemo-mechanical polishing process for transferring the disk-shaped pattern to the LNOI. Nonlinear processes including second harmonic generation and Raman scattering have been demonstrated in the fabricated microdisk.
We numerically study, by means of the single envelope equation, the generation of optical frequency combs ranging from the visible to the mid-infrared spectral regions in resonators with quadratic and cubic nonlinearities. Phase-matched quadratic wave-mixing processes among the comb lines can be activated by low-power continuous wave pumping in the near infrared of a radially poled lithium niobate whispering gallery resonator (WGR). We examine both separate and co-existing intra-cavity doubly resonant second-harmonic generation and parametric oscillation processes, and find that modulation ins…
Optical frequency combs are revolutionising modern time and frequency metrology. In the past years, their range of applications has increased substantially, driven by their miniaturisation through microresonator-based solutions. The combs in such devices are typically generated using the third-order $χ^{(3)}$-nonlinearity of the resonator material. An alternative approach is making use of second-order $χ^{(2)}$-nonlinearities. While the idea of generating combs this way has been around for almost two decades, so far only few demonstrations are known, based either on bulky bow-tie cavities or o…
Cavity optomechanics, the study of the interplay between light and mechanical properties of matter, has triggered a wide range of groundbreaking researches from cavity quantum electrodynamics, label free single molecule detection to the creation of phonon laser. Using femtosecond laser direct writing followed by chemo-mechanical polishing, here we report an ultrahigh quality (Q~10^7) factor lithium niobate (LN) whispering gallery microresonator monolithically integrated with in-plane microelectrodes. Coherent regenerative optomechanical oscillation with an effective mechanical quality (Qm) fac…
Multiple soliton regimes enabled by parametric down-conversion in $χ^{(2)}+χ^{(3)}$ microresonators
University of Bath（巴斯大学）；Centre for Photonics, University of Bath（巴斯大学光子学中心）；VTT Technical Research Centre of Finland（芬兰技术研究中心）；National Physical Laboratory（英国国家物理实验室）
Photolithography assisted chemo-mechanical etching (PLACE), a technique specifically developed for fabricating highquality large-scale photonic integrated circuits (PICs) on thin-film lithium niobate (TFLN), has enabled fabrication of a series of building blocks of PICs ranging from high-quality (high-Q) microresonators and low-loss waveguides to electrooptically (EO) tunable lasers and waveguide amplifiers. Aiming at high-throughput manufacturing of the PIC devices and systems, we have developed an ultra-high-speed high-resolution laser lithography fabrication system employing a high repetiti…
The absence of the single-photon nonlinearity has been a major roadblock in developing quantum photonic circuits at optical frequencies. In this paper, we demonstrate a periodically-poled thin film lithium niobate microring resonator (PPLNMR) that reaches 5,000,000%/W second harmonic conversion efficiency---almost 20-fold enhancement over the state-of-the-art---by accessing its largest $χ^{(2)}$ tensor component $d_{33}$ via quasi-phase matching. The corresponding single photon coupling rate $g/2π$ is estimated to be 1.2 MHz, which is an important milestone as it approaches the dissipation rat…
We investigate the effects of Raman and Kerr gain in crystalline microresonators and determine the conditions required to generate modelocked frequency combs. We show theoretically that strong, narrowband Raman gain determines a maximum microresonator size allowable to achieve comb formation. We verify this condition experimentally in diamond and silicon microresonators and show that there exists a competition between Raman and Kerr effects that leads to the existence of two different comb states.
We observe a transition to a coherent-comb state in a SiN-microresonator with anomalous dispersion. Although ~300 fs pulse trains are generated after line-by-line shaping, the intensity within the microring does not appear to be pulse-like.
Mid-infrared (mid-IR) frequency combs have broad applications in molecular spectroscopy and chemical/biological sensing. Recently developed microresonator-based combs in this wavelength regime could enable portable and robust devices using a single-frequency pump field. Here, we report the first demonstration of a modelocked microresonator-based frequency comb in the mid-IR spanning 2.4 μm to 4.3 μm. We observe high pump-to-comb conversion efficiency, in which 40% of the pump power is converted to the output comb power. Utilizing an integrated PIN structure allows for tuning the silicon micror…
We report the first demonstration of thermally controlled soliton modelocked frequency comb generation in microresonators. By controlling the electric current through heaters integrated with silicon nitride microresonators, we demonstrate a systematic and repeatable pathway to single- and multi-soliton modelocked states without adjusting the pump laser wavelength. Such an approach could greatly simplify the generation of modelocked frequency combs and facilitate applications such as chip-based dual-comb spectroscopy.
We demonstrate that flat-topped dissipative solitonic pulses, platicons, and corresponding frequency combs can be excited in optical microresonators with normal group velocity dispersion using either amplitude modulation of the pump or bichromatic pump. Soft excitation may occur in particular frequency range if modulation depth is large enough and modulation frequency is close to the free spectral range of the microresonator.
We theoretically and experimentally investigate the chaotic regime of optical frequency combs generated in nonlinear ring microresonators pumped with continuous wave light. We show that the chaotic regime reveals itself, in an apparently counter-intuitive way, by a flat top symmetric envelope of the frequency spectrum, when observed by means of an optical spectrum analyzer. The comb demodulated on a fast photodiode produces a noisy radio frequency signal with an spectral width significantly exceeding the linear bandwidth of the microresonator mode.
Kerr frequency combs generated from microresonators are the subject of intense study. Most research employs microresonators with anomalous dispersion, for which modulation instability is believed to play a key role in initiation of the comb. Comb generation in normal dispersion microresonators has also been reported but is less well understood. Here we report a detailed investigation of few-moded, normal dispersion silicon nitride microresonators, showing that mode coupling can strongly modify the local dispersion, even changing its sign. We demonstrate a link between mode coupling and initiat…
A shaped doublet pump pulse is proposed for simultaneous octave-spanning soliton Kerr frequency comb generation and second-harmonic conversion in a single microresonator. The temporal soliton in the cavity is trapped atop a doublet pulse pedestal, resulting in a greatly expanded soliton region compared to that with a general Gaussian pulse pump. The possibility of single-microresonator comb self-referencing in a single silicon nitride microring, which can facilitate compact on-chip optical clocks, is demonstrated via simulation.
We perform the first theoretical modeling of the spectral-temporal dynamics of parametric microresonator comb generation with octave-spanning bandwidths through use of the Lugiato-Lefever model extended to include higher-order dispersion and self-steepening. We show that three distinct stages are necessary to achieve single-pulse modelocking and ultrabroadband, stabilized combs. Our simulations agree well with previous experimental demonstrations and predict many of the observed features, including multi-pulse generation, dispersive wave generation, modelocking and comb stabilization.
We propose a new type of broadband and low repetition rate frequency comb generator which has the shape of an elongated and nanoscale-shallow optical bottle microresonator created at the surface of an optical fiber. The free spectral range (FSR) of the broadband azimuthal eigenfrequency series of this resonator is the exact multiple of the FSR of the dense and narrowband axial series. The effective radius variation of the microresonator is close to a parabola with a nanoscale height which is greater or equal to lambda/2pi*n0 (here lambda is the characteristic radiation wavelength and n0 is the…
We demonstrate control and stabilization of an optical frequency comb generated by four-wave mixing in a monolithic microresonator with a mode spacing in the microwave regime (86 GHz). The comb parameters (mode spacing and offset frequency) are controlled via the power and the frequency of the pump laser, which constitutes one of the comb modes. Furthermore, generation of a microwave beat note at the comb's mode spacing frequency is presented, enabling direct stabilization to a microwave frequency standard.
