With the development of wireless communication, higher requirements arise for train-ground wireless communications in high-speed railway (HSR) scenarios. The millimeter-wave (mm-wave) frequency band with rich spectrum resources can provide users in HSR scenarios with high performance broadband multimedia services, while the full-duplex (FD) technology has become mature. In this paper, we study train-ground communication system performance in HSR scenarios with mobile relays (MRs) mounted on rooftop of train and operating in the FD mode. We formulate a nonlinear programming problem to maximize network capacity by allocation of spectrum resources. Then, we develop a sequential quadratic programming (SQP) algorithm based on the Lagrange function to solve the bandwidth allocation optimization problem for track-side base station (BS) and MRs in this mm-wave train-ground communication system. Extensive simulation results demonstrate that the proposed SQP algorithm can effectively achieve high network capacity for trainground communication in HSR scenarios while being robust to the residual self-interference (SI).
To exploit richer spectrum resources for even better service quality, millimeter wave (mmWave) communication has been considered for high-speed railway (HSR) communication systems. In this paper, we focus on scheduling as many flows as possible while satisfying their QoS requirements. Due to interference, eavesdropping, or other problems, some flows may not be directly transmitted from the track-side BS. In this paper, we propose an UAV-assisted scheduling scheme which utilizes a UAV to serve as relay for such flows. The proposed scheme also utilize two mmWave bands, one for the BS links and t…
In the context of railway systems, the application performance can be very critical and the radio conditions not advantageous. Hence, the communication problem parameters include both a survival time stemming from the application layer and a channel error probability stemming from the PHY layer. This paper proposes to consider the framework of Markov Decision Process (MDP) to design a strategy for scheduling radio resources based on both application and PHY layer parameters. The MDP approach enables to obtain the optimal strategy via the value iteration algorithm. The performance of this algor…
With the rapid development of high-speed railway systems and railway wireless communication, the application of ultra-wideband millimeter wave band is an inevitable trend. However, the millimeter wave channel has large propagation loss and is easy to be blocked. Moreover, there are many problems such as eavesdropping between the base station (BS) and the train. As an emerging technology, reconfigurable intelligent surface (RIS) can achieve the effect of passive beamforming by controlling the propagation of the incident electromagnetic wave in the desired direction.We propose a RIS-assisted sch…
High speed railways (HSRs) have been deployed widely all over the world in recent years. Different from traditional cellular communication, its high mobility makes it essential to implement power allocation along the time. In the HSR case, the transmission rate depends greatly on the distance between the base station (BS) and the train. As a result, the train receives a time varying data rate service when passing by a BS. It is clear that the most efficient power allocation will spend all the power when the train is nearest from the BS, which will cause great unfairness along the time. On the …
In high-speed railway (HSR) communication systems, distributed antenna is usually employed to support frequent handover and enhance the signal to noise ratio to user equipments. In this case, dynamic time-domain power allocation and antenna selection (PAWAS) could be jointly optimized to improve the system performances. This paper consider this problem in such a simple way where dynamic switching between multiple-input-multiple-output (MIMO) and single-input-multiple-output (SIMO) is allowed and exclusively utilized, while the channel states and traffic demand are taken into account. The chann…
With the fast development of high-speed railways, a call for fulfilling the notion of communication at "anytime, anywhere" for high-speed train passengers in the Train Operating Control System is on the way. In order to make a realization of that, new railway wireless communication networks are needed. The most promising one is the Long Term Evolution for Railway which will provide broadband access, fast handover, and reliable communication for high mobility users. However, with the increase of speed, the system is subjected to high bit error rate, Doppler frequency shift and handover failure …
In high speed railways (HSRs) communication system, when a train travels along the railway with high velocity, the wireless channel between the train and base station varies strenuously, which makes it essential to implement appropriate power allocations to guarantee system performance. What's more, how to evaluate the performance limits in this new scenario is also needed to consider. To this end, this paper investigates the performance limits of wireless communication in HSRs scenario. Since the hybrid information transmitted between train and base station usually has diverse quality of serv…
In this letter, we investigate the energy efficiency (EE) problem in a millimeter wave (mmWave) massive MIMO (mMIMO) system with non-orthogonal multiple access (NOMA). Multiple two-user clusters are formulated according to their channel correlation and gain difference. Following this, we propose a hybrid analog/digital precoding scheme for the low radio frequency (RF) chains structure at the base station (BS). On this basis, we formulate a power allocation problem aiming to maximize the EE under users' quality of service (QoS) requirements and per-cluster power constraint. An iterative algorit…
The rapid development of high-speed railways (HSRs) puts forward high requirements on the corresponding communication system. Millimeter wave (mmWave) can be a promising solution due to its wide bandwidth, narrow beams, and rich spectrum resources. However, with the large number of antenna elements employed, energy-efficient solutions at mmWave frequencies are in great demand. Based on a mmWave HSR communication system with multiple mobile relays (MRs) on top of the train, a dynamic power-control scheme for train-ground communications is proposed. The scheme follows the regular movement charac…
High-speed railway (HSR) communications will become a key feature supported by intelligent transportation communication systems. The increasing demand for HSR communications leads to significant attention on the study of radio resource management (RRM), which enables efficient resource utilization and improved system performance. RRM design is a challenging problem due to heterogenous quality of service (QoS) requirements and dynamic characteristics of HSR wireless communications. The objective of this paper is to provide an overview on the key issues that arise in the RRM design for HSR wirel…
This paper investigates the application of non-orthogonal multiple access (NOMA) in millimeter wave (mmWave) communications by exploiting beamforming, user scheduling and power allocation. Random beamforming is invoked for reducing the feedback overhead of considered systems. A nonconvex optimization problem for maximizing the sum rate is formulated, which is proved to be NP-hard. The branch and bound (BB) approach is invoked to obtain the optimal power allocation policy, which is proved to converge to a global optimal solution. To elaborate further, low complexity suboptimal approach is devel…
Future railway is expected to accommodate both train operation services and passenger broadband services. The millimeter wave (mmWave) communication is a promising technology in providing multi-gigabit data rates to onboard users. However, mmWave communications suffer from severe propagation attenuation and vulnerability to blockage, which can be very challenging in high-speed railway (HSR) scenarios. In this paper, we investigate efficient hybrid beamforming (HBF) design for train-to-ground communications. First, we develop a two-stage HBF algorithm in blockage-free scenarios. In the first st…
In this paper, we consider the design of joint resource blocks (RBs) and power allocation for dual-mode base stations operating over millimeter wave (mmW) band and microwave ($μ$W) band. The resource allocation design aims to minimize the system energy consumption while taking into account the channel state information, maximum delay, load, and different types of user applications (UAs). To facilitate the design, we first propose a group-based algorithm to assign UAs to multiple groups. Within each group, low-power UAs, which often appear in short distance and experience less obstacles, are in…
Millimeter wave (mmWave) communication technologies have recently emerged as an attractive solution to meet the exponentially increasing demand on mobile data traffic. Moreover, ultra dense networks (UDNs) combined with mmWave technology are expected to increase both energy efficiency and spectral efficiency. In this paper, user association and power allocation in mmWave based UDNs is considered with attention to load balance constraints, energy harvesting by base stations, user quality of service requirements, energy efficiency, and cross-tier interference limits. The joint user association a…
Millimeter wave (mmWave) communication systems using adaptive-resolution analog-to-digital converters (RADCs) have recently drawn considerable interests from the research community as benefit of their high energy efficiency and low implementation cost. In this paper, we focus on the mmWave uplink using RADCs and investigate the joint user scheduling and resource allocation problem. Specifically, we seek to maximize the system throughput of the scheduled users by jointly optimizing their transmit power level and hybrid combiners as well as the number of quantization bits, subject to practical c…
In this paper we explore non-orthogonal multiple access (NOMA) in millimeter-wave (mmWave) communications (mmWave-NOMA). In particular, we consider a typical problem, i.e., maximization of the sum rate of a 2-user mmWave-NOMA system. In this problem, we need to find the beamforming vector to steer towards the two users simultaneously subject to an analog beamforming structure, while allocating appropriate power to them. As the problem is non-convex and may not be converted to a convex problem with simple manipulations, we propose a suboptimal solution to this problem. The basic idea is to deco…
In this paper, we consider an mmWave-based trainground communication system in the high-speed railway (HSR) scenario, where the computation tasks of users can be partially offloaded to the rail-side base station (BS) or the mobile relays (MRs) deployed on the roof of the train. The MRs operate in the full-duplex (FD) mode to achieve high spectrum utilization. We formulate the problem of minimizing the average task execution latency of all users, under local device and MRs energy consumption constraints. We propose a joint resource allocation and computation offloading scheme (JRACO) to solve t…
In this paper, we investigate the combination of non-orthogonal multiple access and millimeter-Wave communications (mmWave-NOMA). A downlink cellular system is considered, where an analog phased array is equipped at both the base station and users. A joint Tx-Rx beamforming and power allocation problem is formulated to maximize the achievable sum rate (ASR) subject to a minimum rate constraint for each user. As the problem is non-convex, we propose a sub-optimal solution with three stages. In the first stage, the optimal power allocation with a closed form is obtained for an arbitrary fixed Tx…
Ultra-dense (UD) wireless networks and cloud radio access networks (CRAN) are two promising network architectures for the emerging fifth-generation (5G) wireless communication systems. By jointly employing them, a new appealing network solution is proposed in this paper, termed UD-CRAN. In a UD-CRAN, millimeter-wave (mmWave) wireless fronthaul is preferred for information exchange between the central processor and the distributed remote radio heads (RRHs), due to its lower cost and higher flexibility in deployment, compared to fixed optical links. This motivates our study in this paper on the …
We investigate beam training and allocation for multiuser millimeter wave massive MIMO systems. An orthogonal pilot based beam training scheme is first developed to reduce the number of training times, where all users can simultaneously perform the beam training with the base station (BS). As the number of users increases, the same beam from the BS may point to different users, leading to beam conflict and multiuser interference. Therefore, a quality-of-service (QoS) constrained (QC) beam allocation scheme is proposed to maximize the equivalent channel gain of the QoS-satisfied users, under th…
In millimeter wave (mmWave) communication systems, narrow beam operations overcome severe channel attenuations, reduce multiuser interference, and thus introduce the new concept of noise-limited mmWave wireless networks. The regime of the network, whether noise-limited or interference-limited, heavily reflects on the medium access control (MAC) layer throughput and on proper resource allocation and interference management strategies. Yet, alternating presence of these regimes and, more importantly, their dependence on the mmWave design parameters are ignored in the current approaches to mmWave…
In this paper, a novel dual-mode scheduling framework is proposed that jointly performs user applications (UA) selection and scheduling over microwave ($μ$W) and millimeter wave (mmW) bands. The proposed scheduling framework utilizes a set of context information, including the channel state information, the delay tolerance and required load per UA, and the uncertainty of mmW channels, to maximize the quality-of-service (QoS) per UA. The scheduling problem is formulated as an optimization with minimum unsatisfied relations (min-UR) problem which is shown to be challenging to solve. Consequently…
In this paper, we propose a new beam allocation strategy aiming to maximize the average successful tracking probability (ASTP) of time-varying millimeter-wave MIMO systems. In contrast to most existing works that employ one transmitting-receiving (Tx-Rx) beam pair once only in each training period, we investigate a more general framework, where the Tx-Rx beam pairs are allowed to be used repeatedly to improve the received signal powers in specific directions. In the case of orthogonal Tx-Rx beam pairs, a power-based estimator is employed to track the time-varying AoA and AoD of the channel, an…
In mobile millimeter wave (mmWave) systems, energy is a scarce resource due to the large losses in the channel and high energy usage by analog-to-digital converters (ADC), which scales with bandwidth. In this paper, we consider a communication architecture that integrates the sub-6 GHz and mmWave technologies in 5G cellular systems. In order to mitigate the energy scarcity in mmWave systems, we investigate the rate-optimal and energy-efficient physical layer resource allocation jointly across the sub-6 GHz and mmWave interfaces. First, we formulate an optimization problem in which the objectiv…
With the explosive growth of mobile data, the demand of high-speed railway (HSR) passengers for broadband wireless access services urgently needs the support of ultra-highspeed scenario broadband wireless communication. Millimeterwave (mmWave) can achieve high data transmission rates, but it is accompanied by high propagation loss and vulnerability to blockage. To address this issue, developments of directional antennas and unmanned aerial vehicles (UAVs) enhance the robustness of the mmWave train-ground communication system. In this paper, we propose a UAV and MRs relay assistance (UMRA) algo…
As more and more people choose high-speed rail (HSR) as a means of transportation for short trips, there is ever growing demand of high quality of multimedia services. With its rich spectrum resources, millimeter wave (mm-wave) communications can satisfy the high network capacity requirements for HSR. Also, it is possible for receivers (RXs) to be equipped with antenna arrays in mm-wave communication systems due to its short wavelength. However, as HSRs run with high speed, the received signal power (RSP) varies rapidly over a cell and it is the lowest at the edge of the cell compared to other…
Use of low resolution analog to digital converters (ADCs) is an effective way to reduce the high power consumption of millimeter wave (mmWave) receivers. In this paper, a receiver with low resolution ADCs based on adaptive thresholds is considered in downlink mmWave communications in which the channel state information is not known a-priori and acquired through channel estimation. A performance comparison of low-complexity algorithms for power and ADC allocation among transmit and receive terminals, respectively, is provided. Through simulation of practical mmWave cellular networks, it is show…
With the emergence of integrated access and backhaul (IAB) in the fifth generation (5G) of cellular networks, backhaul is no longer just a passive capacity constraint in cellular network design. In fact, this tight integration of access and backhaul is one of the key ways in which 5G millimeter wave (mm-wave) heterogeneous cellular networks (HetNets) differ from traditional settings where the backhaul network was designed independently from the radio access network (RAN). With the goal of elucidating key design trends for this new paradigm, we develop an analytical framework for a two-tier Het…
The fog radio access network (Fog-RAN) has been considered a promising wireless access architecture to help shorten the communication delay and relieve the large data delivery burden over the backhaul links. However, limited by conventional inflexible communication design, Fog-RAN cannot be used in some complex communication scenarios. In this study, we focus on investigating a more intelligent Fog-RAN to assist the communication in a high-speed railway environment. Due to the train's continuously moving, the communication should be designed intelligently to adapt to channel variation. Specifi…
What does millimeter-wave (mmW) seek assistance for from micro-wave (μW) in a mmW overlaid 5G cellular network? This paper raises the question of whether to complement downlink (DL) or uplink (UL) transmissions, and concludes that μW should aid UL more. Such dedication to UL results from the low mmW UL rate due to high peak-to-average power ratio (PAPR) at mobile users. The DL/UL allocations are tractably provided based on a novel closed-form mm-μW spectral efficiency (SE) derivation via stochastic geometry. The findings explicitly indicate: (i) both DL/UL mmW (or μW) SEs coincidentally conver…
The integration of non-orthogonal multiple access in millimeter-Wave communications (mmWave-NOMA) can significantly improve the spectrum efficiency and increase the number of users in the fifth-generation (5G) mobile communication. In this paper we consider a downlink mmWave-NOMA cellular system, where the base station is mounted with an analog beamforming phased array, and multiple users are served in the same time-frequency resource block. To guarantee user fairness, we formulate a joint beamforming and power allocation problem to maximize the minimal achievable rate among the users, i.e., w…
This paper study the effect of interference management arising due to millimeter wave (mmWave) communication on the performance of multiple input multiple output (MIMO) based spectrum sharing cognitive systems. The highly directed mmWave signals have short wavelength property which enables to fabricate an increased number of antennas in a small confined space of the communication system. The large antenna elements are utilized to harvest high beamforming gains and to improve the signal to noise ratio (SNR) by analog processing at the cognitive base station (CBS) and secondary users. Analog pro…
Millimeter wave (mmWave) communication has attracted increasing attention as a promising technology for 5G networks. One of the key architectural features of mmWave is the use of massive antenna arrays at both the transmitter and the receiver sides. Therefore, by employing directional beamforming (BF), both mmWave base stations (MBSs) and mmWave users (MUEs) are capable of supporting multi-beam simultaneous transmissions. However, most researches have only considered a single beam, which means that they do not make full potential of mmWave. In this context, in order to improve the performance …
Fraunhofer Heinrich Hertz Institute（弗劳恩霍夫海因里希·赫兹研究所）；Technical University of Berlin（柏林工业大学）
We propose a method that combines fixed point algorithms with a neural network to optimize jointly discrete and continuous variables in millimeter-wave communication systems, so that the users' rates are allocated fairly in a well-defined sense. In more detail, the discrete variables include user-access point assignments and the beam configurations, while the continuous variables refer to the power allocation. The beam configuration is predicted from user-related information using a neural network. Given the predicted beam configuration, a fixed point algorithm allocates power and assigns user…
In this paper, we propose a hybrid analog-digital beamforming architecture with resolution-adaptive ADCs for millimeter wave (mmWave) receivers with large antenna arrays. We adopt array response vectors for the analog combiners and derive ADC bit-allocation (BA) solutions in closed form. The BA solutions reveal that the optimal number of ADC bits is logarithmically proportional to the RF chain's signal-to-noise ratio raised to the 1/3 power. Using the solutions, two proposed BA algorithms minimize the mean square quantization error of received analog signals under a total ADC power constraint.…
Increased density of wireless devices, ever growing demands for extremely high data rate, and spectrum scarcity at microwave bands make the millimeter wave (mmWave) frequencies an important player in future wireless networks. However, mmWave communication systems exhibit severe attenuation, blockage, deafness, and may need microwave networks for coordination and fall-back support. To compensate for high attenuation, mmWave systems exploit highly directional operation, which in turn substantially reduces the interference footprint. The significant differences between mmWave networks and legacy …
Hybrid precoding can significantly reduce the number of required radio frequency (RF) chains and relieve the huge energy consumption in mmWave massive MIMO systems, thus attracting much interests from academic and industry. However, most existing hybrid precoding schemes are based on singular value decomposition (SVD). Due to the very different sub-channel signal-to-noise ratios (SNRs) after SVD, complicated bit allocations is usually required to match the sub-channel SNRs. To solve this problem, we propose a geometric mean decomposition (GMD)-based hybrid precoding scheme to avoid the complic…
In this paper, a downlink intelligent reflecting surface (IRS) enhanced millimeter-wave (mmWave) non-orthogonal multiple access (NOMA) system is considered. A joint optimization problem over active beamforming, passive beamforming and power allocation is formulated. Due to the highly coupled variables, the formulated optimization problem is non-convex. To solve this problem, an alternative optimization and successive convex approximation based iterative algorithm is proposed. Numerical results illustrate that: 1) the proposed scheme offers significant sum-rate gains, which confirms the effecti…
By allowing a large number of links to be simultaneously transmitted, directional antenna arrays with beamforming have been envisioned as a promising candidate to reach unprecedented levels of spatial isolation. To achieve the high efficiency of spatial reuse in improving system performance, an optimization problem that maximizes the achievable data rate of a multihop heterogeneous network, which incorporates the concept of integrated access and backhaul and supports both downlink and uplink transmissions on access and backhaul links, is formulated. The optimization problem is then systematica…
Millimeter wave offers a sensible solution to the capacity crunch faced by 5G wireless communications. This paper comprehensively studies physical layer security in a multi-input single-output (MISO) millimeter wave system where multiple single-antenna eavesdroppers are randomly located. Concerning the specific propagation characteristics of millimeter wave, we investigate two secure transmission schemes, namely maximum ratio transmitting (MRT) beamforming and artificial noise (AN) beamforming. Specifically, we first derive closed-form expressions of the connection probability for both schemes…
This paper studies the maximum throughput achievable with optimal scheduling in multi-hop mmWave picocellular networks with Multi-user Multiple-Input Multiple-Output (MU-MIMO) radios. MU-MIMO enables simultaneous transmission to multiple receivers (Space Division Multiplexing) and simultaneous reception from multiple transmitters (Space Division Multiple Access). The main contribution is the extension to MU-MIMO of the Network Utility Maximization (NUM) scheduling framework for multi-hop networks. We generalize to MU-MIMO the classic proof that Maximum Back Pressure (MBP) scheduling is NUM opt…
The small cells in millimeter wave (mmWave) have been utilized extensively for the fifth generation (5G) mobile networks. And full-duplex (FD) communications become possible with the development of self-interference (SI) cancellation technology. In this paper, we focus on the optimal allocation of the sub-channels in the small cells deployed densely underlying the mmWave networks. In order to improve the resource utilization and network capacity, device-to-device (D2D) communications are adopted in networks. For maximizing the system throughput, we propose a cooperative sub-channel allocation …
For future networks (i.e., the fifth generation (5G) wireless networks and beyond), millimeter-wave (mmWave) communication with large available unlicensed spectrum is a promising technology that enables gigabit multimedia applications. Thanks to the short wavelength of mmWave radio, massive antenna arrays can be packed into the limited dimensions of mmWave transceivers. Therefore, with directional beamforming (BF), both mmWave transmitters (MTXs) and mmWave receivers (MRXs) are capable of supporting multiple beams in 5G networks. However, for the transmission between an MTX and an MRX, most wo…
Full Duplex (FD) communication can revolutionize wireless communications as it avoids using independent channels for bi-directional communications. This work generalizes the point-to-point FD communication in millimeter wave (mmWave) band consisting of K-pairs of massive MIMO FD nodes operating simultaneously. We present a novel joint hybrid beamforming (HYBF) and combining scheme for weighted sum-rate (WSR) maximization to enable the coexistence of massive MIMO FD links cost-efficiently. The proposed algorithm relies on alternative optimization based on the minorization-maximization method. M…
We propose an effective interference management and beamforming mechanism for uplink communication systems that yields fair allocation of rates. In particular, we consider a hotspot area of a millimeter-wave (mmWave) access network consisting of multiple user equipment (UE) in the uplink and multiple access points (APs) with directional antennas and adjustable beam widths and directions (beam configurations). This network suffers tremendously from multi-beam multi-user interference, and, to improve the uplink transmission performance, we propose a centralized scheme that optimizes the power, t…
This paper proposes a new multiple access technique based on the millimeter wave lens-based reconfigurable antenna systems. In particular, to support a large number of groups of users with different angles of departures (AoDs), we integrate recently proposed reconfigurable antenna multiple access (RAMA) into non-orthogonal multiple access (NOMA). The proposed technique, named reconfigurable antenna NOMA (RA-NOMA), divides the users with respect to their AoDs and channel gains. Users with different AoDs and comparable channel gains are served via RAMA while users with the same AoDs but differen…
In this paper, a novel framework is proposed for optimizing the operation and performance of a large-scale, multi-hop millimeter wave (mmW) backhaul within a wireless small cell network (SCN) that encompasses multiple mobile network operators (MNOs). The proposed framework enables the small base stations (SBSs) to jointly decide on forming the multi-hop, mmW links over backhaul infrastructure that belongs to multiple, independent MNOs, while properly allocating resources across those links. In this regard, the problem is addressed using a novel framework based on matching theory that is compos…
The recent concept of beamspace multiple input multiple output (MIMO) can significantly reduce the number of required radio-frequency (RF) chains in millimeter-wave (mmWave) massive MIMO systems without obvious performance loss. However, the fundamental limit of existing beamspace MIMO is that, the number of supported users cannot be larger than the number of RF chains at the same time-frequency resources. To break this fundamental limit, in this paper we propose a new spectrum and energy efficient mmWave transmission scheme that integrates the concept of non-orthogonal multiple access (NOMA) …
Mobility and blockage are two critical challenges in wireless transmission over millimeter-wave (mmWave) and Terahertz (THz) bands. In this paper, we investigate network massive multiple-input multiple-output (MIMO) transmission for mmWave/THz downlink in the presence of mobility and blockage. Considering the mmWave/THz propagation characteristics, we first propose to apply per-beam synchronization for network massive MIMO to mitigate the channel Doppler and delay dispersion effects. Accordingly, we establish a transmission model. We then investigate network massive MIMO downlink transmission …
Recent researches show that millimeter wave (mmWave) communications can offer orders of magnitude increases in the cellular capacity. However, the secrecy performance of a mmWave cellular network has not been investigated so far. Leveraging the new path-loss and blockage models for mmWave channels, which are significantly different from the conventional microwave channel, this paper comprehensively studies the network-wide physical layer security performance of the downlink transmission in a mmWave cellular network under a stochastic geometry framework. We first study the secure connectivity p…
Millimeter wave (mmWave) communication systems use large number of antenna elements that can potentially overcome severe channel attenuation by narrow beamforming. Narrow-beam operation in mmWave networks also reduces multiuser interference, introducing the concept of noise-limited wireless networks as opposed to interference-limited ones. The noise-limited or interference-limited regime heavily reflects on the medium access control (MAC) layer throughput and on proper resource allocation and interference management strategies. Yet, these regimes are ignored in current approaches to mmWave MAC…
Millimeter wave (mmWave) systems operating over a wide bandwidth and using a large number of antennas impose a heavy burden on power consumption. In a massive multiple-input multiple-output (MIMO) uplink, analog-to-digital con- verters (ADCs) would be the primary consumer of power in the base station receiver. This paper proposes a bit allocation (BA) method for mmWave multi-user (MU) massive MIMO systems under a power constraint. We apply ADCs to the outputs of an analog phased array for beamspace projection to exploit mmWave channel sparsity. We relax a mean square quantization error (MSQE) …
Reconfigurable intelligent surface (RIS) has attracted extensive attention in recent years. However, most research focuses on the scenario of the narrowband and/or instantaneous channel state information (CSI), while wide bandwidth with the use of millimeter-wave (mmWave) (including sub-Terahertz) spectrum is a major trend in next-generation wireless communications, and statistical CSI is more practical to obtain in realistic systems. Thus, we {consider} the ergodic achievable rate of RIS-assisted mmWave multiple-input multiple-output orthogonal frequency division multiplexing communication sy…
Millimeter-wave (mm-wave) communications incur a high beam alignment cost in mobile scenarios such as vehicular networks. Therefore, an efficient beam alignment mechanism is required to mitigate the resulting overhead. In this paper, a one-dimensional mobility model is proposed where a mobile user (MU), such as a vehicle, moves along a straight road with time-varying and random speed, and communicates with base stations (BSs) located on the roadside over the mm-wave band. To compensate for location uncertainty, the BS widens its transmission beam and, when a critical beamwidth is achieved, it …
