In this paper, we reveal that artificial neural network (ANN) assisted multiple-input multiple-output (MIMO) signal detection can be modeled as ANN-assisted lossy vector quantization (VQ), named MIMO-VQ, which is basically a joint statistical channel quantization and signal quantization procedure. It is found that the quantization loss increases linearly with the number of transmit antennas, and thus MIMO-VQ scales poorly with the size of MIMO. Motivated by this finding, we propose a novel modular neural network based approach, termed MNNet, where the whole network is formed by a set of pre-defined ANN modules. The key of ANN module design lies in the integration of parallel interference cancellation in the MNNet, which linearly reduces the interference (or equivalently the number of transmit-antennas) along the feed-forward propagation; and so as the quantization loss. Our simulation results show that the MNNet approach largely improves the deep-learning capacity with near-optimal performance in various cases. Provided that MNNet is well modularized, the learning procedure does not need to be applied on the entire network as a whole, but rather at the modular level. Due to this reason, MNNet has the advantage of much lower learning complexity than other deep-learning based MIMO detection approaches.
We consider high-dimensional MIMO transmissions in frequency division duplexing (FDD) systems. For precoding, the frequency selective channel has to be measured, quantized and fed back to the base station by the users. When the number of antennas is very high this typically leads to prohibitively high quantization complexity and large feedback. In 5G New Radio (NR), a modular quantization approach has been applied for this, where first a low-dimensional subspace is identified for the whole frequency selective channel, and then subband channels are linearly mapped to this subspace and quantized…
8-OAM modes each carrying 10 wavelengths with 2.56-Tbit/s aggregated capacity and 10.24-bit/s/Hz spectral efficiency have been transmitted over 50-km specially designed ring-core fiber, using a compact OAM mode sorter and only modular 4x4 MIMO equalization.
In this work, a scalable and modular architecture for massive MIMO base stations with distributed processing is proposed. New antennas can readily be added by adding a new node as each node handles all the additional involved processing. The architecture supports conjugate beamforming, zero-forcing, and MMSE, where for the two latter cases a central matrix inversion is required. The impact of the time required for this matrix inversion is carefully analyzed along with a generic frame format. As part of the contribution, careful computational, memory, and communication analyses are presented. I…
This paper investigates the effect of oscillator phase noise on a multiuser millimeter wave (mmWave) massive MIMO uplink as we scale up the number of base station antennas, fixing the load factor, defined as the ratio of the number of simultaneous users to the number of base station antennas. We consider a modular approach in which the base station employs an array of subarrays, or "tiles." Each tile supports a fixed number of antennas, and can therefore be implemented using a separate radio frequency integrated circuit (RFIC), with synchronization across tiles accomplished by employing a phas…
In the past ten years, there have been tremendous research progresses on massive MIMO systems, most of which stand from the communications viewpoint. A new trend of investigating massive MIMO, especially for the sparse scenario like millimeter wave (mmWave) transmission, is to re-build the transceiver design from array signal processing viewpoint that could deeply exploit the half-wavelength array and provide enhanced performances in many aspects. For example, the high dimensional channel could be decomposed into small amount of physical parameters, e.g., angle of arrival (AoA), angle of depar…
Coarsely quantized MIMO signalling methods have gained popularity in the recent developments of massive MIMO as they open up opportunities for massive MIMO implementation using cheap and power-efficient radio-frequency front-ends. This paper presents a new one-bit MIMO precoding approach using spatial Sigma-Delta ($ΣΔ$) modulation. In previous one-bit MIMO precoding research, one mainly focuses on using optimization to tackle the difficult binary signal optimization problem that arises from the precoding design. Our approach attempts a different route. Assuming angular MIMO channels, we apply …
Motivated by emerging technologies for energy efficient analog computing and continuous-time processing, this paper proposes continuous-time minimum mean squared error estimation for multiple-input multiple-output (MIMO) systems based on an ordinary differential equation. Mean squared error (MSE) is a principal detection performance measure of estimation methods for MIMO systems. We derive an analytical MSE formula that indicates the MSE at any time. The MSE of the proposed method depends on a regularization parameter which affects the convergence property of the MSE. Furthermore, we extend th…
Southeast University（东南大学）；National Sun Yat-sen University（国立中山大学）；Georgia Institute of Technology（佐治亚理工学院）
In this paper, we investigate the model-driven deep learning (DL) for MIMO detection. In particular, the MIMO detector is specially designed by unfolding an iterative algorithm and adding some trainable parameters. Since the number of trainable parameters is much fewer than the data-driven DL based signal detector, the model-driven DL based MIMO detector can be rapidly trained with a much smaller data set. The proposed MIMO detector can be extended to soft-input soft-output detection easily. Furthermore, we investigate joint MIMO channel estimation and signal detection (JCESD), where the detec…
We present a cognitive prototype that demonstrates a colocated, frequency-division-multiplexed, multiple-input multiple-output (MIMO) radar which implements both temporal and spatial sub-Nyquist sampling. The signal is sampled and recovered via the Xampling framework. Cognition is due to the fact that the transmitter adapts its signal spectrum by emitting only those subbands that the receiver samples and processes. Real-time experiments demonstrate sub-Nyquist MIMO recovery of target scenes with 87.5% spatio-temporal bandwidth reduction and signal-to-noise-ratio of -10 dB.
In this paper, we study joint antenna activity detection, channel estimation, and multiuser detection for massive multiple-input multiple-output (MIMO) systems with general spatial modulation (GSM). We first establish a double-sparsity massive MIMO model by considering the channel sparsity of the massive MIMO channel and the signal sparsity of GSM. Based on the double-sparsity model, we formulate a blind detection problem. To solve the blind detection problem, we develop message-passing based blind channel-and-signal estimation (BCSE) algorithm. The BCSE algorithm basically follows the affine …
In this work, we propose the joint optimization of the automatic gain control (AGC), which works in the remote radio heads (RHHs), and a low-resolution aware (LRA) linear receive filter based on the minimum mean square error (MMSE), which works on the baseband unit (BBU) pool, for large-scale multi-user multiple-input multiple-output (MU-MIMO) systems with coarsely quantized signals in cloud radio access networks. We develop successive interference cancellation receivers based on the proposed joint AGC and LRA-MMSE (AGC-LRA-MMSE) approach. An analysis of the achievable sum rates is also carrie…
In this paper, we study the achievable rate region of 1-layer rate splitting (RS) in the presence of hardware impairment (HWI) and improper Gaussian signaling (IGS) for a single-cell reconfigurable intelligent surface (RIS) assisted broadcast channel (BC). We assume that the transceivers may suffer from an imbalance in in-band and quadrature signals, which is known as I/Q imbalance (IQI). The received signal and noise can be improper when there exists IQI. Therefore, we employ IGS to compensate for IQI as well as to manage interference. Our results show that RS and RIS can significantly enlarg…
The multiple-input multiple-output (MIMO) wiretap channel (WTC), which has a transmitter, a legitimate user and an eavesdropper, is a classic model for studying information theoretic secrecy. In this paper, the fundamental problem for the complex WTC is whether the proper signal is optimal has yet to be given explicit proof, though previous work implicitly assumed the complex signal was proper. Thus, a determinant inequality is proposed to prove that the secrecy rate of a complex Gaussian signal with a fixed covariance matrix in a degraded complex WTC is maximized if and only if the signal is …
Massive multiple-input multiple-out (MIMO) technology is vital in millimeter-wave (mmWave) bands to obtain large array gains. However, there are practical challenges, such as high hardware cost and power consumption in such systems. A promising solution to these problems is to adopt a hybrid beamforming architecture. This architecture has a much lower number of transceiver (TRx) chains than the total antenna number, resulting in cost- and energy-efficient systems. In this paper, we present a real-time mmWave (28 GHz) massive MIMO testbed with hybrid beamforming. This testbed has a 64-antenna/1…
With the capability of reconfiguring the wireless electromagnetic environment, intelligent reflecting surface (IRS) is a new paradigm for designing future wireless communication systems. In this paper, we consider optical IRS for improving the performance of visible light communication (VLC) under a multiple-input and multiple-output (MIMO) setting. Specifically, we focus on the downlink communication of an indoor MIMO VLC system and aim to minimize the mean square error (MSE) of demodulated signals at the receiver. To this end, the MIMO channel gain of the IRS-aided VLC is first derived under…
Massive multiple-input multiple-output (M-MIMO) architecture is the workhorse of modern communication systems. Currently, two fundamental bottlenecks, namely, power consumption and receiver saturation, limit the full potential achievement of this technology. These bottlenecks are intricately linked with the analog-to-digital converter (ADC) used in each radio frequency (RF) chain. The power consumption in MIMO systems grows exponentially with the ADC's bit budget while ADC saturation causes permanent loss of information. This motivates the need for a solution that can simultaneously tackle the…
This paper considers signal detection in massive multiple-input multiple-output (MIMO) systems with general additive hardware impairments and one-bit quantization. First, we present the quantization-unaware and Bussgang decomposition-based linear receivers by generalizing them for the considered hardware impairment model. We propose an optimization problem to estimate the uplink data signals by choosing a suitable cost function that treats the unquantized received signal at the base station as the variable. We exploit the additional structure of the one-bit quantization and signal modulation b…
Hangzhou Institute of Technology, Xidian University（西安电子科技大学杭州研究院）；Xidian University（西安电子科技大学）；University of Wollongong（伍伦贡大学）；Weizmann Institute of Science（魏茨曼科学研究所）；University of Sydney（悉尼大学）
In this paper, we investigate signal detection in multiple-input-multiple-output (MIMO) communication systems with hardware impairments, such as power amplifier nonlinearity and in-phase/quadrature imbalance. To deal with the complex combined effects of hardware imperfections, neural network (NN) techniques, in particular deep neural networks (DNNs), have been studied to directly compensate for the impact of hardware impairments. However, it is difficult to train a DNN with limited pilot signals, hindering its practical applications. In this work, we investigate how to achieve efficient Bayesi…
Subspace methods are essential to high-resolution environment sensing in the emerging unmanned systems, if further combined with the millimeter-wave (mm-Wave) massive multi-input multi-output (MIMO) technique. The estimation of signal/noise subspace, as one critical step, is yet computationally complex and presents a particular challenge when developing high-resolution yet low-complexity automotive radars. In this work, we develop a fast randomized-MUSIC (R-MUSIC) algorithm, which exploits the random matrix sketching to estimate the signal subspace via approximated computation. Our new approac…
In this paper, we propose an optimization framework for rate splitting (RS) techniques in multiple-input multiple-output (MIMO) reconfigurable intelligent surface (RIS)-assisted systems, possibly with I/Q imbalance (IQI). This framework can be applied to any optimization problem in which the objective and/or constraints are linear functions of the rates and/or transmit covariance matrices. Such problems include minimum-weighted and weighted-sum rate maximization, total power minimization for a target rate, minimum-weighted energy efficiency (EE) and global EE maximization. The framework may be…
Multiple-input multiple-output (MIMO) signaling is one of the key technologies of current mobile communication systems. However, the complex and expensive radio frequency (RF) chains have always limited the increase of MIMO scale. In this paper, we propose a MIMO transmission architecture based on a dual-polarized reconfigurable intelligent surface (RIS), which can directly achieve modulation and transmission of multichannel signals without the need for conventional RF chains. Compared with previous works, the proposed architecture can improve the integration of RIS-based transmission systems.…
In this paper, the Hermite polynomials are employed to study linear approximation models of narrowband multiantenna signal reception (i.e., MIMO) with low-resolution quantizations. This study results in a novel linear approximation using the second-order Hermite expansion (SOHE). The SOHE model is not based on those assumptions often used in existing linear approximations. Instead, the quantization distortion is characterized by the second-order Hermite kernel, and the signal term is characterized by the first-order Hermite kernel. It is shown that the SOHE model can explain almost all phenome…
In this paper, we adapt to cell-free Massive MIMO (multiple-input multiple-output) the finite-blocklength framework introduced by Östman et al. (2020) for the characterization of the packet error probability achievable with Massive MIMO, in the ultra-reliable low-latency communications (URLLC) regime. The framework considered in this paper encompasses a cell-free architecture with imperfect channel-state information, and arbitrary linear signal processing performed at a central-processing unit connected to the access points via fronthaul links. By means of numerical simulations, we show that, …
Phase Modulation on the Hypersphere (PMH) is a power efficient modulation scheme for the \textit{load-modulated} multiple-input multiple-output (MIMO) transmitters with central power amplifiers (CPA). However, it is difficult to obtain the precise channel state information (CSI), and the traditional optimal maximum likelihood (ML) detection scheme incurs high complexity which increases exponentially with the number of antennas and the number of bits carried per antenna in the PMH modulation. To detect the PMH signals without knowing the prior CSI, we first propose a signal detection scheme, te…
Reconfigurable intelligent surface (RIS) technique stands as a promising signal enhancement or signal cancellation technique for next generation networks. We design a novel passive beamforming weight at RISs in a multiple-input multiple-output (MIMO) non-orthogonal multiple access (NOMA) network for simultaneously serving paired users, where a signal cancellation based (SCB) design is employed. In order to implement the proposed SCB design, we first evaluate the minimal required number of RISs in both the diffuse scattering and anomalous reflector scenarios. Then, new channel statistics are de…
Multi input multi output (MIMO) systems\' capability of using seperate signals brings many advantages to radar signal processing and time frequency analysis. In this paper, a variety of properties of MIMO ambiguity functions related with representations of Heisenberg group are given. Some of the existing results for SIMO ambiguity functions are generalized to MIMO case. Combined effect of seperate signals is investigated.
Dealing with nonlinear effects of the radio-frequency(RF) chain is a key issue in the realization of very large-scale multi-antenna (MIMO) systems. Achieving the remarkable gains possible with massive MIMO requires that the signal processing algorithms systematically take into account these effects. Here, we present a computationally efficient linear precoding method satisfying the requirements for low peak-to-average power ratio (PAPR) and low-resolution D/A-converters (DACs). The method is based on a sparse regularization of the precoding matrix and offers advantages in terms of precoded sig…
To enable user diversity and multiplexing gains, a fully digital precoding multiple input multiple output (MIMO) architecture is typically applied. However, a large number of radio frequency (RF) chains make the system unrealistic to low-cost communications. Therefore, a practical three-stage hybrid analogue-digital precoding architecture, occupying fewer RF chains, is proposed aiming for a non-orthogonal IoT signal in low-cost multiuser MIMO systems. The non-orthogonal waveform can flexibly save spectral resources for massive devices connections or improve data rate without consuming extra sp…
In this letter, we consider the problem of channel estimation for large intelligent metasurface (LIM) assisted massive multiple-input multiple-output (MIMO) systems. The main challenge of this problem is that the LIM integrated with a large number of low-cost metamaterial antennas can only passively reflect the incident signal by a certain phase shift, and does not have any signal processing capability. To deal with this, we introduce a general framework for the estimation of the transmitter-LIM and LIM-receiver cascaded channel, and propose a two-stage algorithm that includes a sparse matrix …
Forecasting time series on graphs is a fundamental problem in graph signal processing. When each entity of the network carries a vector of values for each time stamp instead of a scalar one, existing approaches resort to the use of product graphs to combine this multidimensional information, at the expense of creating a larger graph. In this paper, we show the limitations of such approaches, and propose extensions to tackle them. Then, we propose a recursive multiple-input multiple-output graph filter which encompasses many already existing models in the literature while being more flexible. N…
Virginia Tech（弗吉尼亚理工大学）；Samsung Research America（三星美国研究院）
In this paper, we investigate learning-based MIMO-OFDM symbol detection strategies focusing on a special recurrent neural network (RNN) -- reservoir computing (RC). We first introduce the Time-Frequency RC to take advantage of the structural information inherent in OFDM signals. Using the time domain RC and the time-frequency RC as the building blocks, we provide two extensions of the shallow RC to RCNet: 1) Stacking multiple time domain RCs; 2) Stacking multiple time-frequency RCs into a deep structure. The combination of RNN dynamics, the time-frequency structure of MIMO-OFDM signals, and th…
In this paper, over-the-air experiments with external and internal interferences were performed using Chalmers millimeter-wave multiple-input-multiple-output testbed MATE. The resulting SINR for both interference experiments are compared and discussed.
Joint communication and sensing (JCAS) has the potential to improve the overall energy, cost and frequency efficiency of IoT systems. As a first effort, we propose to optimize the MIMO-OFDM data symbols carried by sub-carriers for better time- and spatial-domain signal orthogonality. This not only boosts the availability of usable signals for JCAS, but also significantly facilitates Internet-of-Things (IoT) devices to perform high-quality sensing. We establish an optimization problem that modifies data symbols on sub-carriers to enhance the above-mentioned signal orthogonality. We also develop…
In this paper, we investigate jointly sparse signal recovery and jointly sparse support recovery in Multiple Measurement Vector (MMV) models for complex signals, which arise in many applications in communications and signal processing. Recent key applications include channel estimation and device activity detection in MIMO-based grant-free random access which is proposed to support massive machine-type communications (mMTC) for Internet of Things (IoT). Utilizing techniques in compressive sensing, optimization and deep learning, we propose two model-driven approaches, based on the standard aut…
