Millimeter-wave (mmWave) frequency bands are expected to be used for future 5G networks due to the availability of large unused spectrum. However, the attenuation at mmWave frequencies is high. To resolve this issue, the utilization of high gain antennas and beamforming mechanisms are widely investigated in the literature. In this work, we considered mmWave end-to-end propagation modeled by individual ray sources, and explored the effects of the number of rays in the model and radiation patterns of the deployed antennas on the received power. It is shown that taking the dominant two rays is sufficient to model the channel for outdoor open areas as opposed to the indoor corridor which needs five dominant rays to have a good fit for the measurement and simulation results. It is observed that the radiation pattern of the antenna affects the slope of the path loss. Multi-path components increase the received power, thus, for indoor corridor scenarios, path loss according to the link distance is smaller for lower gain antennas due to increased reception of reflected components. For an outdoor open area, the slope of the path loss is found to be very close to that of the free space.
The availability of large unused spectrum at millimeter wave (mmWave) frequency bands has steered the future 5G research towards these bands. However, mmWave signals are attenuated severely in the non-lineof-sight (NLOS) scenarios, thereby leaving the strong link quality by a large margin to line-of-sight (LOS) links. In this paper, a passive metallic reflector is used to enhance the coverage for mmWave signals in an outdoor, NLOS propagation scenarios. The received power from different azimuth and elevation angles are measured at 28 GHz in a parking lot setting. Our results show that using a …
In the upcoming 5G communication, the millimeter-wave (mmWave) technology will play an important role due to its large bandwidth and high data rate. However, mmWave frequencies have higher free-space path loss (FSPL) in line-of-sight (LOS) propagation compared to the currently used sub-6 GHz frequencies. What is more, in non-line-of-sight (NLOS) propagation, the attenuation of mmWave is larger compared to the lower frequencies, which can seriously degrade the performance. It is therefore necessary to investigate mmWave propagation characteristics for a given deployment scenario to understand c…
This paper presents the design, implementation and evaluation of milliMap, a single-chip millimetre wave (mmWave) radar based indoor mapping system targetted towards low-visibility environments to assist in emergency response. A unique feature of milliMap is that it only leverages a low-cost, off-the-shelf mmWave radar, but can reconstruct a dense grid map with accuracy comparable to lidar, as well as providing semantic annotations of objects on the map. milliMap makes two key technical contributions. First, it autonomously overcomes the sparsity and multi-path noise of mmWave signals by combi…
Base station (BS) placement in mobile networks is critical to the efficient use of resources in any communication system and one of the main factors that determines the quality of communication. Although there is ample literature on the optimum placement of BSs for sub-6 GHz bands, channel propagation characteristics, such as penetration loss, are notably different in millimeter-wave (mmWave) bands than in sub-6 GHz bands. Therefore, designated solutions are needed for mmWave systems to have reliable quality of service (QoS) assessment. This article proposes a multi-armed bandit (MAB) learning…
In this paper, we investigate an outdoor and indoor wireless communication network with the assistance of a novel relay-aided double-sided reconfigurable intelligent surface (RIS). A scheduling problem is considered at the outdoor access point (AP) to minimize the sum of age of information (AoI). To serve the indoor users and further enhance the wireless link quality, a novel double-sided RIS with relay is utilized. Since the formulated problem is non-convex with highly-coupled variables, a successive convex approximation (SCA) based alternating optimization (AO) algorithm is proposed to solve…
In the US, people spend 87% of their time indoors and have an average of four connected devices per person (in 2020). As such, providing indoor coverage has always been a challenge but becomes even more difficult as carrier frequencies increase to mmWave and beyond. This paper investigates the outdoor and outdoor-indoor coverage of an urban network comparing globally standardized building penetration models and implementing models to corresponding scenarios. The glass used in windows of buildings in the grid plays a pivotal role in determining the outdoor-to-indoor propagation loss. For 28 GHz…
Substantial growth of demand for mobile data and rapidly increasing spread of personal communication devices such as smart phones and tablets is the major challenge faced by the mobile service providers in recent years. The allotted spectrum for the currently operating mobile communication systems have been saturated in the last few years by such a considerable rate that the future fifth generation network would not be able to operate without applying new frequencies. In accordance with the concept of 5G, millimeter wave frequency band will also be used along with the currently used frequency …
With the increasing adoption of millimeter-waves (mmWave) over cellular networks, outdoor-to-indoor (O2I) communication has been one of the challenging research problems due to high penetration loss of buildings. To address this, we investigate the practicability of utilizing reconfigurable intelligent surfaces (RISs) for assisting such O2I communication. We propose a new notion of prefabricated RIS-empowered wall consisting of a large number of chipless radio frequency identification (RFID) sensors. Each sensor maintains its own bank of delay lines. These sensors which are built within the bu…
In this paper, two large-scale fading path loss models are presented based on indoor and outdoor channel measurements at 73 GHz. The line-of-sight millimeter-wave propagation measurement campaigns were uniquely conducted within the indoor and outdoor environments at an airport setting, i.e., the Boise Airport. The channel measurements were made with directional transmit and receive antennas with a 24 dBi gain at different receive antenna heights. From the measured data, we obtained the parameters of two path loss models, i.e., the close-in reference distance model (CIM) and the floating-interc…
In this paper, we consider a heterogeneous 5G cellular architecture that separates the outdoor and indoor scenarios and in particular study the trade-off between the spectrum efficiency (SE), energy efficiency (EE), economy efficiency (ECE). Mathematical expressions for the system capacity, EE, SE, and ECE respectively are derived using a proposed realistic power consumption model. The comparison of system performance in terms of SE, EE, and ECE, results in the observation that the proposed network architecture, which separates the outdoor and indoor scenarios, offers a promising solution for …
In this paper, we present millimeter-wave (mmWave) penetration loss measurements and analysis at E-bands-73 GHz and 81 GHz. Penetration loss was measured for common building materials such as clear glass, metal, tinted glass, wood, and drywall on the campus of Boise State University in the city of Boise. A horn antenna with a gain of 24 dBi was used at the transmitter and receiver at both bands, and both antennas were boresight-aligned with respect to the test material. A total of twelve locations were selected to test five materials. We tested two indoor materials (clear glass and wood) in at…
Simultaneously transmitting (refracting) and reflecting reconfigurable intelligent surfaces (STAR-RISs) have been recently identified to improve the spectrum/energy efficiency and extend the communication range. However, their potential for enhanced concurrent indoor and outdoor localization has not yet been explored. In this paper, we study the fundamental limits, i.e., the Cramér Rao lower bounds (CRLBs) via Fisher information analyses, on the three-dimensional (3D) localization performance with a STAR-RIS at millimeter wave frequencies. The effect of the power splitting between refraction a…
Millimeter-wave (mmWave) and terahertz (THz) spectrum can support significantly higher data rates compared to lower frequency bands and hence are being actively considered for 5G wireless networks and beyond. These bands have high free-space path loss (FSPL) in line-of-sight (LOS) propagation due to their shorter wavelength. Moreover, in non-line-of-sight (NLOS) scenario, these two bands suffer higher penetration loss than lower frequency bands which could seriously affect the network coverage. It is therefore critical to study the NLOS penetration loss introduced by different building materia…
The high attenuation of millimeter-wave (mmWave) would significantly reduce the coverage areas, and hence it is critical to study the propagation characteristics of mmWave in multiple deployment scenarios. In this work, we investigated the propagation and scattering behavior of 60 GHz mmWave signals in outdoor environments at a travel distance of 98 m for an aerial link (rooftop to rooftop), and 147 m for a ground link (light-pole to light-pole). Measurements were carried out using Facebook Terragraph (TG) radios. Results include received power, path loss, signal-to-noise ratio (SNR), and root…
The future 5G networks are expected to use millimeter wave (mmWave) frequency bands, mainly due to the availability of large unused spectrum. However, due to high path loss at mmWave frequencies, coverage of mmWave signals can get severely reduced, especially for non-line-of-sight (NLOS) scenarios. In this work, we study the use of passive metallic reflectors of different shapes/sizes to improve mmWave signal coverage for indoor NLOS scenarios. Software defined radio based mmWave transceiver platforms operating at 28 GHz are used for indoor measurements. Subsequently, ray tracing (RT) simulati…
Recent research and development interests deal with metasurfaces for wireless systems beyond their consideration as intelligent tunable reflectors. Among the latest proposals is the simultaneously transmitting (a.k.a. refracting) and reflecting reconfigurable intelligent surface (STAR-RIS) which intends to enable bidirectional indoor-to-outdoor, and vice versa, communications thanks to its additional refraction capability. This double functionality provides increased flexibility in concurrently satisfying the quality-of-service requirements of users located at both sides of the metasurfaces, f…
Indoor areas, such as offices and shopping malls, are a natural environment for initial millimeter-wave (mmWave) deployments. While we already have the technology that enables us to realize indoor mmWave deployments, there are many remaining challenges associated with system-level design and planning for such. The objective of this article is to bring together multiple strands of research to provide a comprehensive and integrated framework for the design and performance evaluation of indoor mmWave systems. The paper introduces the framework with a status update on mmWave technology, including …
An indoor layout sensing and localization system in 60GHz millimeter wave (mmWave) band, named mmReality, is elaborated in this paper. The mmReality system consists of one transmitter and one mobile receiver, each with a phased array and a single radio frequency (RF) chain. To reconstruct the room layout, the pilot signal is delivered from the transmitter to the receiver via different pairs of transmission and receiving beams, so that the signals at all antenna elements can be resolved. Then, the spatial smoothing and two-dimensional multiple signal classification (MUSIC) algorithm is applied …
Millimeter wave (mmWave) bands have been utilized for the fifth generation (5G) communication systems and will no doubt continue to be deployed for beyond 5G (B5G). However, the underlying channels are not fully investigated at multifrequency bands and in multi-scenarios by using the same channel sounder, especially for the outdoor, multiple-input multiple-output (MIMO), and vehicle-to-vehicle (V2V) conditions. In this paper, we conduct multi-frequency multi-scenario mmWave MIMO channel measurements with 4*4 antennas at 28, 32, and 39 GHz bands for three cases, i.e., the human body and vehicle…
Outdoor-to-indoor communications in millimeter-wave (mmWave) cellular networks have been one challenging research problem due to the severe attenuation and the high penetration loss caused by the propagation characteristics of mmWave signals. We propose a viable solution to implement the outdoor-to-indoor mmWave communication system with the aid of an active intelligent transmitting surface (active-ITS), where the active-ITS allows the incoming signal from an outdoor base station (BS) to pass through the surface and be received by the indoor user-equipments (UEs) after shifting its phase and m…
Today, a large portion of the mobile data traffic is consumed behind the shielding walls of buildings or in the Faraday cage of trains. This renders cellular network coverage from outdoor cell sites difficult. Indoor small cells and distributed antennas along train tracks are often considered as a solution, but the cost and the need for optical fiber backhaul are often prohibitive. To alleviate this issue, we describe an out-of-band repeater that converts a sub-6 GHz cell signal from a small cell installed at a cell tower to a mmWave frequency for the fronthaul to buildings or distributed ante…
Reconfigurable intelligent surface (RIS)-assisted communication appears as one of the potential enablers for sixth generation (6G) wireless networks by providing a new degree of freedom in the system design to telecom operators. Particularly, RIS-empowered millimeter wave (mmWave) communication systems can be a remedy to provide broadband and ubiquitous connectivity. This paper aims to fill an important gap in the open literature by providing a physical, accurate, open-source, and widely applicable RIS channel model for mmWave frequencies. Our model is not only applicable in various indoor and…
Localization is important for a large number of Internet of Things (IoT) endpoint devices connected by LoRaWAN. Due to the bandwidth limitations of LoRaWAN, existing localization methods without specialized hardware (e.g., GPS) produce poor performance. To increase the localization accuracy, we propose a super-resolution localization method, called Seirios, which features a novel algorithm to synchronize multiple non-overlapped communication channels by exploiting the unique features of the radio physical layer to increase the overall bandwidth. By exploiting both the original and the conjugat…
In this work, we consider the deployment of reconfigurable intelligent surfaces (RISs) to extend the coverage of a millimeter-wave (mmWave) network in indoor dense spaces. We first integrate RIS into ray-tracing simulations to realistically capture the propagation characteristics, then formulate a non-convex optimization problem that minimizes the number of RISs under rate constraints. We propose a feasible point pursuit and successive convex approximation-based algorithm, which solves the problem by jointly selecting the RIS locations, optimizing the RIS phase-shifts, and allocating time reso…
Millimeter wave (mmWave) access networks have the potential to meet the high-throughput and low-latency needs of immersive applications. However, due to the highly directional nature of the mmWave beams and their susceptibility to beam misalignment and blockage resulting from user movements and rotations, the associated mmWave links are vulnerable to large channel fluctuations. These fluctuations result in disproportionately adverse effects on performance of transport layer protocols such as Transmission Control Protocol (TCP). To overcome this challenge, we propose a network layer solution, C…
This paper presents a method for continuous indoor-outdoor environment detection on mobile devices based solely on WiFi fingerprints. Detection of indoor outdoor switching is an important part of identifying a user's context, and it provides important information for upper layer context aware mobile applications such as recommender systems, navigation tools, etc. Moreover, future indoor positioning systems are likely to use Wi-Fi fingerprints, and therefore Wi-Fi receivers will be on most of the time. In contrast to existing research, we believe that these fingerprints should be leveraged, and…
Energy efficiency (EE) is a major performance metric for fifth generation (5G) and beyond 5G (B5G) wireless communication systems, especially for ultra dense networks. This paper proposes an end-to-end (e2e) power consumption model and studies the energy efficiency for a heterogeneous B5G cellular architecture that separates the indoor and outdoor communication scenarios in ultra dense networks. In this work, massive multiple-input-multiple-output (MIMO) technologies at conventional sub-6 GHz frequencies are used for long-distance outdoor communications. Light-Fidelity (LiFi) and millimeter wa…
Indoor millimeter-wave (mmWave) environment channels are typically sparsely-scattered and dominated by a strong line-of-sight (LOS) path. Therefore, communication over such channels is in general extremely difficult when the LOS path is not present. However, the recent introduction of reconfigurable intelligent surfaces (RISs), which have the potential to influence the propagation environment in a controlled manner, has the potential to change the previous paradigm. Motivated by this, we study the channel capacity optimization utilizing RISs in indoor mmWave environments where no LOS path is p…
Reconfigurable intelligent surface (RIS)-empowered communication is one of the promising 6G technologies that allows the conversion of the wireless channel into an intelligent transmit entity by manipulating the impinging waves using man-made surfaces. In this paper, the potential benefits of using RISs are investigated for indoor/outdoor setups and various frequency bands (from sub 6 GHz to millimeter-waves). First, a general system model with a single RIS is considered and the effect of the total number of reflecting elements on the probabilistic distribution of the received signal-to-noise …
The 6th generation of wireless communication (6G) is envisioned to give rise to various technologies for improving the end-to-end communication performance, where the communication is envisioned to utilize wireless signals in the millimeter wave (mmWave) frequencies and above. Among others, these technologies comprise Intelligent Reflective Surfaces (IRSs) and Mobile Relays (MRs), whose envisaged roles include mitigating the negative effects of Non-Line-of-Sight (NLoS) connectivity, in particular at mmWave and higher frequencies. The core idea behind these technologies is to use cooperative ne…
The objective of the Enhanced Mobile Broadband use case in 5G networks is to deliver high capacity access to densely populated areas, like city centres, transportation hubs or convention centres. Millimetre-wave communications are the go-to technology to realise that objective, yet due to weak outdoor-to-indoor penetration, outdoor deployments will not suffice and dedicated indoor deployments will be necessary. In this article, we study dense deployments of millimetre-wave access points mounted on the ceiling, with directional antennas pointing downwards to illuminate selected spots on the gro…
University of Trento（特伦托大学）；Lund University（隆德大学）；University of Padova（帕多瓦大学）
The commercial availability of low-cost millimeter wave (mmWave) communication and radar devices is starting to improve the penetration of such technologies in consumer markets, paving the way for large-scale and dense deployments in fifth-generation (5G)-and-beyond as well as 6G networks. At the same time, pervasive mmWave access will enable device localization and device-free sensing with unprecedented accuracy, especially with respect to sub-6 GHz commercial-grade devices. This paper surveys the state of the art in device-based localization and device-free sensing using mmWave communication…
Outdoor-to-indoor (OtI) signal propagation further challenges the already tight link budgets at millimeter-wave (mmWave). To gain insight into OtI mmWave scenarios at 28 GHz, we conducted an extensive measurement campaign consisting of over 2,200 link measurements. In total, 43 OtI scenarios were measured in West Harlem, New York City, covering seven highly diverse buildings. The measured OtI path gain can vary by up to 40 dB for a given link distance, and the empirical path gain model for all data shows an average of 30 dB excess loss over free space at distances beyond 50 m, with an RMS fitt…
