Mobility management is a major challenge for the wide-spread deployment of millimeter-wave (mmWave) cellular networks. In particular, directional beamforming in mmWave devices renders high-speed mobility support very complex. This complexity, however, is not limited to system design but also the performance estimation and evaluation. Hence, some have turned their attention to stochastic modeling of mmWave vehicular communication to derive closed-form expressions characterizing the coverage and rate behavior of the network. In this article, we model and analyze the beam management for mmWave vehicular networks. To the best of our knowledge, this is the first work that goes beyond coverage and rate analysis. Specifically, we focus on a multi-lane divided highway scenario in which base stations and vehicles are present on both sides of the highway. In addition to providing analytical expressions for the average number of beam switching and handover events, we provide design insights for the network operators to fine-tune their network within the flexibility provided by the standard in the choice of system parameters, including the number of resources dedicated to channel feedback and beam alignment operations.
Vehicular communications essentially support automotive applications for safety and infotainment. For this reason, industry leaders envision an enhanced role of vehicular communications in the fifth generation of mobile communications technology. Over the years, the number of vehicle-mounted sensors has increased steadily, which potentially leads to more volume of critical data communications in a short time. Also, emerging applications such as remote/autonomous driving and infotainment such as high-definition movie streaming require data-rates on the order of multiple Gbit/s. Such high data-r…
Autonomous Self-Trained Channel State Prediction Method for mmWave Vehicular Communications
Faculty of Technical Sciences, University of Novi Sad（诺维萨德大学技术科学学院）；The Institute for Artificial Intelligence Research and Development of Serbia（塞尔维亚人工智能研究与发展研究所）；African Center of Excellence in IoT, University of Rwanda（卢旺达大学非洲物联网卓越中心）
Millimeter-wave (mmwave) communication represents a potential solution to capacity shortage in vehicular networks. However, effective beam alignment between senders and receivers requires accurate knowledge of the vehicles' position for fast beam steering, which is often impractical to obtain in real time. We address this problem by leveraging the traffic signals regulating vehicular mobility: as an example, we may coordinate beams with red traffic lights, as they correspond to higher vehicle densities and lower speeds. To evaluate our intuition, we propose a tractable, yet accurate, mmwave co…
Millimeter wave (mmWave) communication is one viable solution to support Gbps sensor data sharing in vehicular networks. The use of large antenna arrays at mmWave and high mobility in vehicular communication make it challenging to design fast beam alignment solutions. In this paper, we propose a novel framework that learns the channel angle-of-departure (AoD) statistics at a base station (BS) and uses this information to efficiently acquire channel measurements. Our framework integrates online learning for compressive sensing (CS) codebook learning and the optimized codebook is used for CS-bas…
Millimeter wave channels exhibit structure that allows beam alignment with fewer channel measurements than exhaustive beam search. From a compressed sensing (CS) perspective, the received channel measurements are usually obtained by multiplying a CS matrix with a sparse representation of the channel matrix. Due to the constraints imposed by analog processing, designing CS matrices that efficiently exploit the channel structure is, however, challenging. In this paper, we propose an end-to-end deep learning technique to design a structured CS matrix that is well suited to the underlying channel …
Millimeter wave (MmWave) systems are vulnerable to blockages, which cause signal drop and link outage. One solution is to deploy reconfigurable intelligent surfaces (RISs) to add a strong non-line-of-sight path from the transmitter to receiver. To achieve the best performance, the location of the deployed RIS should be optimized for a given site, considering the distribution of potential users and possible blockers. In this paper, we find the optimal location, height and downtilt of RIS working in a realistic vehicular scenario. Because of the proximity between the RIS and the vehicles, and th…
Radio-based vehicular simultaneous localization and mapping (SLAM) aims to localize vehicles while mapping the landmarks in the environment. We propose a sequence of three Poisson multi-Bernoulli mixture (PMBM) based SLAM filters, which handle the entire SLAM problem in a theoretically optimal manner. The complexity of the three proposed SLAM filters is progressively reduced while sustaining high accuracy by deriving SLAM density approximation with the marginalization of nuisance parameters (either vehicle state or data association). Firstly, the PMBM SLAM filter serves as the foundation, for …
In intelligent transportation systems (ITS), vehicles are expected to feature with advanced applications and services which demand ultra-high data rates and low-latency communications. For that, the millimeter wave (mmWave) communication has been emerging as a very promising solution. However, incorporating the mmWave into ITS is particularly challenging due to the high mobility of vehicles and the inherent sensitivity of mmWave beams to dynamic blockages. This article addresses these problems by developing an optimal beam association framework for mmWave vehicular networks under high mobility…
5G new radio (NR) provides new opportunities for accurate positioning from a single reference station: large bandwidth combined with multiple antennas, at both the base station and user sides, allows for unparalleled angle and delay resolution. Nevertheless, positioning quality is affected by multipath and clock biases. We study, in terms of performance bounds and algorithms, the ability to localize a vehicle in the presence of multipath and unknown user clock bias. We find that when a sufficient number of paths is present, a vehicle can still be localized thanks to redundancy in the geometric…
Successive Pose Estimation and Beam Tracking for mmWave Vehicular Communication Systems
National University of Singapore（国立新加坡大学）；Shenzhen Research Institute of Big Data（深圳大数据研究院）；Southern University of Science and Technology（南方科技大学）；Queen Mary University of London（伦敦女王玛丽大学）；The University of Hong Kong（香港大学）
Millimeter wave (mmWave) has been claimed to be the only viable solution for high-bandwidth vehicular communications. However, frequent channel estimation and beamforming required to provide a satisfactory quality of service limits mmWave for vehicular communications. In this paper, we propose a novel channel estimation and beam tracking framework for mmWave communications in a vehicular network setting. For channel estimation, we propose an algorithm termed robust adaptive multi-feedback (RAF) that achieves comparable estimation performance as existing channel estimation algorithms, with a si…
In this paper, we study the performance of millimeter wave (mmWave) vehicular communications (VCs) using non-orthogonal multiple access scheme (NOMA) at road intersections, since there areas are more prone to accidents. We study the case when the intersection involves two perpendicular lanes, we then extend the study to an intersection with several lanes. The transmission occurs between a source, and two destinations. The transmission experiences interference originated from a set of vehicles that are distributed as a Poisson point process (PPP). Our analysis includes the effects of blockage f…
Vehicle-to-Everything (V2X) communications are revolutionizing the connectivity of transportation systems supporting safe and efficient road mobility. To meet the growing bandwidth eagerness of V2X services, millimeter-wave (e.g., 5G new radio over spectrum 26.50 - 48.20 GHz) and sub-THz (e.g., 120 GHz) frequencies are being investigated for the large available spectrum. Communication at these frequencies requires beam-type connectivity as a solution for the severe path loss attenuation. However, beams can be blocked, with negative consequences for communication reliability. Blockage predictio…
Autonomous vehicles will rely heavily on vehicle-to-everything (V2X) communications to obtain a large amount of information required for navigation and road safety purposes. This can be achieved through: (i) leveraging millimeter-wave (mmWave) frequencies to achieve multi- Gbps data rates, and (ii) exploiting the temporal and spatial correlation of vehicular contents to offload a portion of the traffic from the infrastructure via caching. Characterizing such a system under mmWave directional beamforming, high vehicular mobility, channel fluctuations, and different caching strategies is a compl…
Millimeter-wave radars are being increasingly integrated into commercial vehicles to support advanced driver-assistance system features. A key shortcoming for present-day vehicular radar imaging is poor azimuth resolution (for side-looking operation) due to the form factor limits on antenna size and placement. In this paper, we propose a solution via a new multiple-input and multiple-output synthetic aperture radar (MIMO-SAR) imaging technique, that applies coherent SAR principles to vehicular MIMO radar to improve the side-view (angular) resolution. The proposed 2-stage hierarchical MIMO-SAR …
Recently, millimeter wave (mmWave) bands have been investigated as a means to enhance automated driving and address the challenging data rate and latency demands of emerging automotive applications. For the development of those systems to operate in bands above 6 GHz, there is a need to have accurate channel models able to predict the peculiarities of the vehicular propagation at these bands, especially as far as Vehicle-to-Vehicle (V2V) communications are concerned. In this paper, we validate the channel model that the 3GPP has proposed for NR-V2X systems, which (i) supports deployment scenar…
Recently, intelligent reflecting surface (IRS) assisted mmWave networks are emerging, which bear the potential to address the blockage issue of the millimeter wave (mmWave) communication in a more cost-effective way. In particular, IRS is built by passive and programmable electromagnetic elements that can manipulate the mmWave propagation channel into a more favorable condition that is free of blockage via judicious joint BS-IRS transmission design. However, the coexistence of IRSs and mmWave BSs complicates the network architecture, and thus poses great challenges for efficient beam managemen…
Cooperative relays improve reliability and coverage in wireless networks by providing multiple paths for data transmission. Relaying will play an essential role in vehicular networks at higher frequency bands, where mobility and frequent signal blockages cause link outages. To ensure connectivity in a relay-aided vehicular network, the relay selection policy should be designed to efficiently find unblocked relays. Inspired by recent advances in beam management in mobile millimeter wave (mmWave) networks, this paper address the question: how can the best relay be selected with minimal overhead …
Vehicle electronic systems currently utilize wired networks for power delivery (from the main battery) and communication (e.g., LIN, CAN, FlexRay) between nodes. Wired networks cannot practically accommodate nodes in moving parts (e.g., tires) and with the increasing functional complexity in vehicles, they require kilometer-long harnesses, significantly increasing fuel consumption and manufacturing and design costs. As an alternative, energy harvesting intra-vehicular wireless sensor networks (IVWSN) can accommodate nodes in all locations and they obviate the need for wiring, significantly low…
Radar-Only Long-Term Beam Prediction in mmWave Vehicular Networks: An Empirical Study of Doppler Input and Cross-Modal Distillation
Hanyang University（汉阳大学）；University of Oulu（奥卢大学）；Electronics and Telecommunications Research Institute (ETRI)（电子通信研究所）；University of Science and Technology (UST)（科学技术大学）
5G applications have become increasingly popular in recent years as the spread of fifth-generation (5G) network deployment has grown. For vehicular networks, mmWave band signals have been well studied and used for communication and sensing. In this work, we propose a new dynamic ray tracing algorithm that exploits spatial and temporal coherence. We evaluate the performance by comparing the results on typical vehicular communication scenarios with GEMV^2, which uses a combination of deterministic and stochastic models, and WinProp, which utilizes the deterministic model for simulations with giv…
The connected vehicle paradigm empowers vehicles with the capability to communicate with neighboring vehicles and infrastructure, shifting the role of vehicles from a transportation tool to an intelligent service platform. Meanwhile, the transportation electrification pushes forward the electric vehicle (EV) commercialization to reduce the greenhouse gas emission by petroleum combustion. The unstoppable trends of connected vehicle and EVs transform the traditional vehicular system to an electric vehicular network (EVN), a clean, mobile, and safe system. However, due to the mobility and heterog…
Multi-Modal Sensing Residual-Corrected GNN for mmWave Path Loss Prediction via Synesthesia of Machines
Joint SDU-NTU Centre for Artificial Intelligence Research (C-FAIR), Shandong University（山东大学中德人工智能联合研究中心）；School of Software, Shandong University（山东大学软件学院）；State Key Laboratory of Photonics and Communications, School of Electronics, Peking University（北京大学电子工程学院光通信与光子学国家重点实验室）
This paper presents a novel spatially consistent approach for modeling line-of-sight (LOS) paths in vehicular networks. We use stochastic geometry to model transmitters, obstacles, and receivers located in three parallel lines, respectively. Their geometric interactions are leveraged to characterize the existence of LOS paths. Specifically, the proposed approach focuses on the role of obstacles in blocking one or more LOS paths, which has been overlooked in most statistical models for blockage. Under the proposed framework, we derive the probability that a typical vehicle is in LOS with respec…
Learning the covariance matrices of spatially-correlated wireless channels, in millimeter-wave (mmWave) vehicular communication, can be utilized in designing environmen-taware beamforming codebooks. Such channel covariance matrices can be represented on non-Euclidean Riemannian manifolds, thanks to their symmetric positive definite (SPD) characteristics. Consequently in this paper, we propose a Riemannian-Geometric machine learning (G-ML) approach for estimating the channel covariance matrices based on unsupervised K-Means model. The proposed K-means algorithm utilizes Log-Euclidean metric (LE…
Millimeter-wave (mmWave) communication is a promising technology to meet the ever-growing data traffic of vehicular communications. Unfortunately, more frequent channel estimations are required in this spectrum due to the narrow beams employed to compensate for the high path loss. Hence, the development of highly efficient beam tracking algorithms is essential to enable the technology, particularly for fast-changing environments in vehicular communications. In this paper, we propose an innovative scheme for beam tracking based on the Extended Kalman Filter (EKF), improving the mean square erro…
Vehicular congestion is directly impacting the efficiency of the transport sector. A wireless sensor network for vehicular clients is used in Internet of Vehicles based solutions for traffic management applications. It was found that vehicular congestion detection by using Internet of Vehicles based connected vehicles technology are practically feasible for congestion handling. It was found that by using Fog Computing based principles in the vehicular wireless sensor network, communication in the system can be improved to support larger number of nodes without impacting performance. In this pa…
Vision-aided wireless communication is motivated by the recent advances in deep learning and computer vision as well as the increasing dependence on line-of-sight links in millimeter wave (mmWave) and terahertz systems. By leveraging vision, this new research direction enables an interesting set of new capabilities such as vision-aided mmWave beam and blockage prediction, proactive hand-off, and resource allocation among others. These capabilities have the potential of reliably supporting highly-mobile applications such as vehicular/drone communications and wireless virtual/augmented reality i…
High resolution compressive channel estimation provides information for vehicle localization when a hybrid mmWave MIMO system is considered. Complexity and memory requirements can, however, become a bottleneck when high accuracy localization is required. An additional challenge is the need of path order information to apply the appropriate geometric relationships between the channel path parameters and the vehicle, RSU and scatterers position. In this paper, we propose a low complexity channel estimation strategy of the angle of departure and time difference of arrival based on multidimensiona…
Integrating Unmanned Aerial Vehicles (UAVs) into future Intelligent Transportation Systems (ITSs) allows to exploit their unique mobility potentials for improving the performance of services such as near-field parcel delivery, dynamic network provisioning, and aerial sensing. In order to provide a controllable environment for the methodological performance analysis, simulation frameworks need to support ground- and aerial-based mobility as well as the involved communication technologies. In this paper, we present the open source Lightweight ICT-centric Mobility Simulation (LIMoSim) framework f…
This paper presents an inertial sensor aided technique for beam alignment and tracking in massive multiple-input multiple-output (MIMO) vehicle-to-vehicle (V2V) communications based on millimeter waves (mmWave). Since directional communications in vehicular scenarios are severely hindered by beam pointing issues, a beam alignment procedure has to be periodically carried out to guarantee the communication reliability. When dealing with massive MIMO links, the beam sweeping approach is known to be time consuming and often unfeasible due to latency constraints. To speed up the process, we propose…
In this paper, we study the impact and the improvement of using cooperative non-orthogonal multiple access scheme (NOMA) on a millimeter wave (mmWave) vehicular network at intersection roads. The intersections consists of two perpendicular roads. The transmission occurs between a source, and two destinations nodes with a help of a relay. We assume that the interference comes from as set of vehicles that are distributed as a one dimensional homogeneous Poisson point process (PPP). We derive closed form outage probability expressions for cooperative NOMA, and compare them with cooperative orthog…
Millimeter wave (mmWave) bands have been utilized for the fifth generation (5G) communication systems and will no doubt continue to be deployed for beyond 5G (B5G). However, the underlying channels are not fully investigated at multifrequency bands and in multi-scenarios by using the same channel sounder, especially for the outdoor, multiple-input multiple-output (MIMO), and vehicle-to-vehicle (V2V) conditions. In this paper, we conduct multi-frequency multi-scenario mmWave MIMO channel measurements with 4*4 antennas at 28, 32, and 39 GHz bands for three cases, i.e., the human body and vehicle…
A BEV-Fusion Based Framework for Sequential Multi-Modal Beam Prediction in mmWave Systems
National Mobile Communications Research Laboratory, Southeast University（东南大学移动通信国家重点实验室）；Pervasive Communication Research Center, Purple Mountain Laboratories（紫金山实验室泛在通信研究中心）
Position-aided beam selection methods have been shown to be an effective approach to achieve high beamforming gain while limiting the overhead and latency of initial access in millimeter wave (mmWave) communications. Most research in the area, however, has focused on vehicular applications, where the orientation of the user terminal (UT) is mostly fixed at each position of the environment. This paper proposes a location- and orientation-based beam selection method to enable context information (CI)-based beam alignment in applications where the UT can take arbitrary orientation at each locatio…
As one of the most promising applications in future Internet of Things, Internet of Vehicles (IoV) has been acknowledged as a fundamental technology for developing the Intelligent Transportation Systems in smart cities. With the emergence of the sixth generation (6G) communications technologies, massive network infrastructures will be densely deployed and the number of network nodes will increase exponentially, leading to extremely high energy consumption. There has been an upsurge of interest to develop the green IoV towards sustainable vehicular communication and networking in the 6G era. In…
