In the small-cell networks (SCNs) with multiple small-cell base stations (ScBSs), the joint design of beamforming vectors, user scheduling and ScBS sleeping is investigated with the constraints on proportional rate. A long-term grid-energy expenditure minimization problem is formulated for the considered SCNs, which are powered by the smart grid and natural renewable energy. Since the scheduled user indicators are coupled with the beamforming vectors, the formulated problem is challenging to handle. In order to decouple the beamforming vectors from the scheduled user indicators, the Lyapunov optimization technique is used. As a result, a practical two-scale algorithm is proposed to allocate the user scheduling indicators and ScBS sleeping variables at the coarse-grained granularity (frame) as well as obtain the beamforming vectors at the fine-grained granularity (slot). Numerical results are used to verify the performance of the proposed two-scale algorithm.
In this paper, a novel intelligent reflecting surface (IRS)-assisted wireless powered communication network (WPCN) architecture is proposed for power-constrained Internet-of-Things (IoT) smart devices, where IRS is exploited to improve the performance of WPCN under imperfect channel state information (CSI). We formulate a hybrid access point (HAP) transmit energy minimization problem by jointly optimizing time allocation, HAP energy beamforming, receiving beamforming, user transmit power allocation, IRS energy reflection coefficient and information reflection coefficient under the imperfect CS…
In this correspondence, we consider an amplify-and-forward relay network in which relayed information is overheard by an eavesdropper. In order to confound the eavesdropper, a wireless-powered jammer is also considered which harvests energy from a multiple-antenna source. We proposed a new secure beamforming scheme in which beamforming vector is a linear combination of the energy beamforming (EB) and information beamforming (IB) vectors. We also present a new closed-form solution for the proposed beamforming vector which is shown to achieve a higher secrecy rate as compared to the trivial EB a…
This paper investigates Cell-Free massive MIMO networks, where each access point (AP) is equipped with a hybrid transceiver, reducing the complexity and cost compared to a fully digital transceiver. Asymptotic approximations for the spectral efficiency are derived for uplink and downlink. Capitalizing on these expressions, a max-min problem is formulated to optimize the (i) analog beamformer at the APs and (ii) pilot assignment. Simulations show that the optimization of these variables substantially increases the network performance.
This letter deals with the opportunistic beamforming (OBF) scheme for multi-antenna downlink with spatial randomness. In contrast to conventional OBF, the terminals return only 1-bit feedback, which is powered by wireless power transfer through a rectenna array. We study two fundamental topologies for the combination of the rectenna elements; the direct-current combiner and the radio-frequency combiner. The beam outage probability is derived in closed form for both combination schemes, by using high order statistics and stochastic geometry.
This paper considers an active intelligent reflecting surface (IRS)-aided wireless powered communication network (WPCN), where devices first harvest energy and then transmit information to a hybrid access point (HAP). Different from the existing works on passive IRS-aided WPCNs, this is the first work that introduces the active IRS in WPCNs. To guarantee fairness, the problem is formulated as an amplifying power-limited weighted sum throughput (WST) maximization problem, which is solved by successive convex approximation technique and fractional programming alternatively. To balance the perfor…
User scheduling, beamforming and energy coordination are investigated in smart-grid powered cellular networks (SGPCNs), where the base stations are powered by a smart grid and natural renewable energy sources. Heterogeneous energy coordination is considered in SGPCNs, namely energy merchandizing with the smart grid and energy exchanging among the base stations. A long-term grid-energy expenditure minimization problem with proportional-rate constraints is formulated for SGPCNs. Since user scheduling is coupled with the beamforming vectors, the formulated problem is challenging to handle via sta…
In this work, we maximize the secrecy rate of the wireless-powered untrusted relay network by jointly designing power splitting (PS) ratio and relay beamforming with the proposed global optimal algorithm (GOA) and local optimal algorithm (LOA). Different from the literature, artificial noise (AN) sent by the destination not only degrades the channel condition of the eavesdropper to improve the secrecy rate, but also becomes a new source of energy powering the untrusted relay based on PS. Hence, it is of high economic benefits and efficiency to take advantage of AN compared with the literature.…
In this paper, we study the performance of blind adaptive beamforming algorithms for smart antennas in realistic environments. A constrained constant modulus (CCM) design criterion is described and used for deriving a recursive least squares (RLS) type optimization algorithm. Furthermore, two kinds of scenarios are considered in the paper for analyzing its performance. Simulations are performed to compare the performance of the proposed method to other well-known methods for blind adaptive beamforming. Results indicate that the proposed method has a significant faster convergence rate, better …
The new paradigm of wirelessly powered two-tier heterogeneous networks (HetNets) is considered in this paper. Specifically, the femtocell base station (FBS) is powered by a power beacon (PB) and transmits confidential information to a legitimate femtocell user (FU) in the presence of a potential eavesdropper (EVE) and a macro base station (MBS). In this scenario, we investigate the secrecy beamforming design under three different levels of FBS-EVE channel state information (CSI), namely, the perfect, imperfect and completely unknown FBS-EVE CSI. Firstly, given the perfect global CSI at the FBS…
The physical-layer security issue in the multiple non-regenerative wireless-powered relay (WPR) networks is investigated in this letter, where the idle relay is treated as a potential eavesdropper. To guarantee secure communication, the destination-based artificial noise is sent to degrade the receptions of eavesdroppers, and it also becomes a new source of energy powering relays to forward the information with power splitting (PS) technique. We propose an efficient algorithm ground on block-wise penalty function method to jointly optimize PS ratio and beamforming to maximize the secrecy rate.…
In this paper, we study the average throughput performance of energy beamforming in a multi-antenna wireless-powered communication network (WPCN). The considered network consists of one hybrid access-point (AP) with multiple antennas and a single antenna user. The user does not have constant power supply and thus needs to harvest energy from the signals broadcast by the AP in the downlink (DL), before sending its data back to the AP with the harvested energy in the uplink (UL). We derive closed-form expressions of the average throughput and their asymptotic expressions at high SNR for both del…
This paper studies a system where a set of $N$ relay nodes harvest energy from the signal received from a source to later utilize it when forwarding the source's data to a destination node via distributed beamforming. To this end, we derive (approximate) analytical expressions for the mean SNR at destination node when relays employ: i) time-switching based energy harvesting policy, ii) power-splitting based energy harvesting policy. The obtained results facilitate the study of the interplay between the energy harvesting parameters and the synchronization error, and their combined impact on mea…
This paper investigates a multi-input single-output (MISO) wireless powered communication network (WPCN) under the protocol of harvest-then-transmit. The power station (PS) with reliable power supply can replenish the passive user nodes by wireless power transfer (WPT) in the downlink (DL), then each user node transmits independent information to the sink by a time division multiple access (TDMA) scheme in the uplink (UL). We consider the joint time allocation and beamforming design to maximize the system sum-throughput. The semidefinite relaxation (SDR) technique is applied to solve the nonco…
Wireless powered sensor networks (WPSNs) have emerged as a key development towards the future self-sustainable Internet of Things (IoT) networks. To achieve a good balance between self-sustainability and reliability, partially WPSNs with a mixed power solution are desirable for practical applications. Specifically, most of the sensor nodes are wireless powered but the key sensor node adopts traditional wire/battery power for reliability. As a result, this paper mainly investigates optimal design for the partially WPSNs in which simultaneous wireless information and power transfer (SWIPT) is ad…
The newly emerging wireless powered communication networks (WPCNs) have recently drawn significant attention, where radio signals are used to power wireless terminals for information transmission. In this paper, we study a WPCN where one multi-antenna access point (AP) coordinates energy transfer and information transfer to/from a set of single-antenna users. A harvest-then-transmit protocol is assumed where the AP first broadcasts wireless power to all users via energy beamforming in the downlink (DL), and then the users send their independent information to the AP simultaneously in the uplin…
The application of renewable energy is a promising solution to realize the Green Communications. However, if the cellular systems are solely powered by the renewable energy, the weather dependence of the renewable energy arrival makes the systems unstable. On the other hand, the proliferation of the smart grid facilitates the loads with two-way energy trading capability. Hence, a hybrid powered cellular system, which combines the smart grid with the base stations, can reduce the grid energy expenditure and improve the utilization efficiency of the renewable energy. In this paper, the long-term…
We propose techniques for optimizing transmit beamforming in a full-duplex multiple-input-multiple-output (MIMO) wireless-powered communication system, which consists of two phases. In the first phase, the wireless-powered mobile station (MS) harvests energy using signals from the base station (BS), whereas in the second phase, both MS and BS communicate to each other in a full-duplex mode. When complete instantaneous channel state information (CSI) is available, the BS beamformer and the time-splitting (TS) parameter of energy harvesting are jointly optimized in order to obtain the BS-MS rate…
In this paper, we consider a three-node cooperative wireless powered communication system consisting of a multi-antenna hybrid access point (H-AP) and a single-antenna relay and a single-antenna user. The energy constrained relay and user first harvest energy in the downlink and then the relay assists the user using the harvested power for information transmission in the uplink. The optimal energy beamforming vector and the time split between harvest and cooperation are investigated. To reduce the computational complexity, suboptimal designs are also studied, where closed-form expressions are …
This letter studies a multi-antenna wireless powered communication (WPC) system with co-channel energy and information transfer, where a wireless device (WD), powered up by wireless energy transfer (WET) from an energy transmitter (ET), communicates to an information receiver (IR) over the same frequency band. We maximize the achievable data rate from the WD to the IR by jointly optimizing the energy beamforming at the ET and the information beamforming at the WD, subject to their individual transmit power constraints. We obtain the optimal solution to this problem in closed-form, where the op…
In this article, we present a real-time three dimensional (3D) hybrid beamforming for fifth generation (5G) wireless networks. One of the key concepts in 5G cellular systems is the small cell network, which settles the high mobile traffic demand and provides uniform user-experienced data rates. The overall capacity of the small cell network can be enhanced with the enabling technology of 3D hybrid beamforming. This study validates the feasibility of the 3D hybrid beamforming, mostly for link-level performances, through the implementation of a realtime testbed using a software-defined radio (SD…
As a revolution in networking, Internet of Things (IoT) aims at automating the operations of our societies by connecting and leveraging an enormous number of distributed devices (e.g., sensors and actuators). One design challenge is efficient wireless data aggregation (WDA) over tremendous IoT devices. This can enable a series of IoT applications ranging from latency-sensitive high-mobility sensing to data-intensive distributed machine learning. Over-the-air (functional) computation (AirComp) has emerged to be a promising solution that merges computing and communication by exploiting analogwav…
The high reflect beamforming gain of the intelligent reflecting surface (IRS) makes it appealing not only for wireless information transmission but also for wireless power transfer. In this letter, we consider an IRS-assisted wireless powered communication network, where a base station (BS) transmits energy to multiple users grouped into multiple clusters in the downlink, and the clustered users transmit information to the BS in the manner of hybrid non-orthogonal multiple access and time division multiple access in the uplink. We investigate optimizing the reflect beamforming of the IRS and t…
For a self-sustaining wireless communication system in Internet-of-Things (IoT) networks, energy harvesting (EH) can be implemented at each user node as a constant renewable power supply source. Hence, an investigation into the use of wireless powered communication network (WPCN) protocols to facilitate communication between an access point (AP) and multiple mobile users (MUs) is presented in this paper. The AP has multiple antennas and operates in the full-duplex (FD) mode. The MUs, on the other hand, have single antennas and works in the half-duplex (HD) mode. Each MU communicating with the …
In this paper, we investigate a multi-node multi-antenna wireless-powered sensor networks (WPSN) comprised of one power beacon and multiple sensor nodes. We have implemented a real-life multi-node multi-antenna WPSN testbed that operates in real time. We propose a beam-splitting beamforming technique that enables a power beacon to split microwave energy beams towards multiple nodes for simultaneous charging. We experimentally demonstrate that the beam-splitting beamforming technique achieves the Pareto optimality. For a perpetual operation of the sensor nodes, we adopt an energy neutral contro…
This paper considers a two-way data exchanging system with a constant powered access point and an energy-harvesting powered smart device. The access point simultaneously transmits information and energy to the smart device with fixed powers $\barρ P_\text{t}$ and $ρP_\text{t}$, respectively. Upon collecting enough energy, the smart device performs one block of transmission immediately. We investigate the timeless of the two-way data exchange in terms of age of information (AoI). Specifically, we investigate the trade-off between downlink timeliness and uplink timeliness by optimizing the weigh…
In this paper, we investigate the worst-case robust beamforming design and resource block (RB) assignment problem for total transmit power minimization of the central controller while guaranteeing each robot's transmission with target number of data bits and within required ultra-low latency and extremely high reliability. By using the property of the independence of each robot's beamformer design, we can obtain the equivalent power control design form of the original beamforming design. The binary RB mapping indicators are transformed into continuous ones with additional $\ell_0$-norm constra…
This paper studies the energy management in the coordinated multi-point (CoMP) systems powered by smart grids, where each base station (BS) with local renewable energy generation is allowed to implement the two-way energy trading with the grid. Due to the uneven renewable energy supply and communication energy demand over distributed BSs as well as the difference in the prices for their buying/selling energy from/to the gird, it is beneficial for the cooperative BSs to jointly manage their energy trading with the grid and energy consumption in CoMP based communication for reducing the total en…
In this paper, we consider a wireless powered multi-relay network in which a multi-antenna hybrid access point underlaying a cellular system transmits information to distant receivers. Multiple relays capable of energy harvesting are deployed in the network to assist the information transmission. The hybrid access point can wirelessly supply energy to the relays, achieving multi-user gains from signal and energy cooperation. We propose a joint optimization for signal beamforming of the hybrid access point as well as wireless energy harvesting and collaborative beamforming strategies of the rel…
This paper studies a wireless powered mobile edge computing (MEC) system with device-to-device (D2D)-enabled task offloading. In this system, a set of distributed multi-antenna energy transmitters (ETs) use collaborative energy beamforming to wirelessly charge multiple users. By using the harvested energy, the actively computing user nodes can offload their computation tasks to nearby idle users (as helper nodes) via D2D communication links for self-sustainable remote computing. We consider the frequency division multiple access (FDMA) protocol, such that the D2D communications of different us…
Intelligent reflecting surface (IRS) is a proposing technology in 6G to enhance the performance of wireless networks by smartly reconfiguring the propagation environment with a large number of passive reflecting elements. However, current works mainly focus on single IRS-empowered wireless networks, where the channel rank deficiency problem has emerged. In this paper, we propose a distributed IRS-empowered communication network architecture, where multiple source-destination pairs communicate through multiple distributed IRSs. We further contribute to maximize the achievable sum-rates in this …
In this paper, we study a multi-cluster Wireless Powered Communication Network (WPCN) where each cluster of users cooperate with a Cluster Head (CH) and a Hybrid Access Point (HAP). All users are equipped with multiple antennas. This HAP employs beamforming to deliver energy to the users in the downlink phase. The users of each cluster transmit their signals to the HAP and to their CHs in the uplink phase. In the next step the CHs first relay the signals of their cluster users and then transmit their own information to the HAP. We design the Energy Beamforming (EB) matrix, transmit covariance …
In this paper, a two-hop decode-and-forward cognitive radio system with deployed interference alignment is considered. The relay node is energy-constrained and scavenges the energy from the interference signals. In the literature, there are two main energy harvesting protocols, namely, time-switching relaying and power-splitting relaying. We first demonstrate how to design the beamforming matrices for the considered primary and secondary networks. Then, the system capacity under perfect and imperfect channel state information scenarios, considering different portions of time-switching and powe…
Wirelessly powered backscatter communication (WPBC) has been identified as a promising technology for low-power communication systems, which can reap the benefits of energy beamforming to improve energy transfer efficiency. However, existing studies on energy beamforming fail to simultaneously take energy supply and information transfer in WPBC into account. This paper takes the first step to fill this gap, by considering the restrictive relationship between the energy harvesting rate and achievable rate with estimated backscatter channel state information (BS-CSI). To ensure reliable communic…
This paper studies a two-hop decode-and-forward underlay cognitive radio system with interference alignment technique. An energy-constrained relay node harvests the energy from the interference signals through a power-splitting (PS) relaying protocol. Firstly, the beamforming matrices design for the primary and secondary networks is demonstrated. Then, a bit error rate (BER) performance of the system under perfect and imperfect channel state information (CSI) scenarios for PS protocol is calculated. Finally, the impact of the CSI mismatch parameters on the BER performance is simulated.
Visibility-Region Coupling in XL-MIMO AGV Fleets: Triple-Role Modeling and Masked Beamforming
King Abdullah University of Science and Technology (KAUST)（阿卜杜拉国王科技大学）；Institute of Advanced Intelligence and Computing, Agency for Science, Technology and Research (A*STAR IAIC)（新加坡科技研究局先进智能与计算研究所）
Wireless powered backscatter communications (WPBC) is capable of implementing ultra-low-power communication, thus promising in the Internet of Things (IoT) networks. In practice, however, it is challenging to apply WPBC in large-scale IoT networks because of its short communication range. To address this challenge, this paper exploits an unmanned ground vehicle (UGV) to assist WPBC in large-scale IoT networks. In particular, we investigate the joint design of network planning and dynamic resource allocation of the access point (AP), tag reader, and UGV to minimize the total energy consumption.…
Intelligent reflecting surface (IRS) is a promising technology to improve the performance of wireless powered communication networks (WPCNs) due to its capability to reconfigure signal propagation environments via smart reflection. In particular, the high passive beamforming gain promised by IRS can significantly enhance the efficiency of both downlink wireless power transfer (DL WPT) and uplink wireless information transmission (UL WIT) in WPCNs. Although adopting different IRS phase shifts for DL WPT and UL WIT, i.e., dynamic IRS beamforming, is in principle possible but incurs additional si…
With the explosive growth of smart devices and mobile data traffic, limited fronthaul capacity has become a notable bottleneck of green communication access networks, such as cloud radio access networks(C-RANs). In this paper, we proposed a joint user association and downlink beamforming scheme for green C-RANs to minimize the network power consumption with the limited fronthaul links. We first formulate the design problem as a mixed integer nonlinear programming (MINLP), and then transformed the MINLP problem into a mixed integer second-order cone program (MI-SOCP) which is a convex program w…
We study two-user multiple-input single-output (MISO) wireless powered communication networks (WPCNs), where the user devices are equipped with non-linear energy harvesting (EH) circuits. We consider time-division duplex (TDD) transmission, where the users harvest power from the signal received in the downlink phase, and then, utilize this harvested power for information transmission in the uplink phase. In contrast to existing works, we adopt a non-linear model of the harvested power based on a precise analysis of the employed EH circuit. We jointly optimize the beamforming vectors in the dow…
In this paper, we design a new smart software-defined radio access network architecture which is flexible and traffic and density aware for the fifth generation (5G) of cellular wireless networks and beyond. The proposed architecture, based on network parameters such as density of users and system traffic, performs five important tasks namely, dynamic radio resource management (RRM), dynamic BS type selection, dynamic functionality splitting, dynamic transmission technology selection, and dynamic framing. In this regard, we first elaborate the structure of the proposed smart soft-RAN model and…
Wireless technologies can support a broad range of smart grid applications including advanced metering infrastructure (AMI) and demand response (DR). However, there are many formidable challenges when wireless technologies are applied to the smart gird, e.g., the tradeoffs between wireless coverage and capacity, the high reliability requirement for communication, and limited spectral resources. Relaying has emerged as one of the most promising candidate solutions for addressing these issues. In this article, an introduction to various relaying strategies is presented, together with a discussio…
Intelligent reflecting surface (IRS) has recently been emerged as an effective way for improving the performance of wireless networks by reconfiguring the propagation environment through a large number of passive reflecting elements. This game-changing technology is especially important for stepping into the Internet of Everything (IoE) era, where high performance is demanded with very limited available resources. In this paper, we study a backscatter-assisted wireless powered communication network (BS-WPCN), in which a number of energy-constrained users, powered by a power station (PS), trans…
This paper considers a wireless powered communication network (WPCN) with group cooperation, where two communication groups cooperate with each other via wireless power transfer and time sharing to fulfill their expected information delivering and achieve "win-win" collaboration. To explore the system performance limits, we formulate optimization problems to respectively maximize the weighted sum-rate and minimize the total consumed power. The time assignment, beamforming vector and power allocation are jointly optimized under available power and quality of service requirement constraints of b…
Intelligent reflecting surface (IRS) has emerged as an enabling technology to achieve smart and reconfigurable wireless communication environment cost-effectively. Prior works on IRS mainly consider its passive beamforming design and performance optimization without the inter-IRS signal reflection, which thus do not unveil the full potential of multi-IRS assisted wireless networks. In this paper, we study a double-IRS assisted multi-user communication system with the \emph{cooperative} passive beamforming design that captures the multiplicative beamforming gain from the inter-IRS channel. Unde…
Smart multiantenna wireless power transmission can enable perpetual operation of energy harvesting (EH) nodes in the internet-of-things. Moreover, to overcome the increased hardware cost and space constraints associated with having large antenna arrays at the radio frequency (RF) energy source, the hybrid energy beamforming (EBF) architecture with single RF chain can be adopted. Using the recently proposed hybrid EBF architecture modeling the practical analog phase shifter impairments (API), we derive the optimal least-squares estimator for the energy source to EH user channel. Next, the avera…
This paper studies secrecy transmission with the aid of a group of wireless energy harvesting (WEH)-enabled amplify-and-forward (AF) relays performing cooperative jamming (CJ) and relaying. The source node in the network does simultaneous wireless information and power transfer (SWIPT) with each relay employing a power splitting (PS) receiver in the first phase; each relay further divides its harvested power for forwarding the received signal and generating artificial noise (AN) for jamming the eavesdroppers in the second transmission phase. In the centralized case with global channel state in…
In this paper, we consider a frequency-division duplexing (FDD) multiple-user multiple-input-single-output (MU-MISO) wireless-powered communication network (WPCN) consisting of one hybrid data-and-energy access point (HAP) with multiple antennas which coordinates energy/information transfer to/from several single-antenna wireless devices (WD). Typically, in such a system, wireless energy transfer (WET) requires such techniques as energy beamforming (EB) for efficient transfer of energy to the WDs. Yet, efficient EB can only be accomplished if channel state information (CSI) is available to the…
Intelligent reflecting surface (IRS) is envisioned to have abundant applications in future wireless networks by smartly reconfiguring the signal propagation for performance enhancement. Specifically, an IRS consists of a large number of low-cost passive elements each reflecting the incident signal with a certain phase shift to collaboratively achieve beamforming and suppress interference at one or more designated receivers. In this paper, we study an IRS-enhanced point-to-point multiple-input single-output (MISO) wireless system where one IRS is deployed to assist in the communication from a m…
