Electrolyte stability against oxidation is one of the important factors limiting the development of high energy density batteries. HOMO level of solvent molecules has been successfully used for understanding trends in their oxidative stability but assumes a non-interacting environment. However, solvent HOMO levels are renormalized due to molecules in their solvation shells. In this work, we first demonstrate an inexpensive and accurate method to determine the HOMO level of solvent followed by simple descriptors for renormalization of HOMO level due to different electrolyte components. The descriptors are based on Gutmann Donor and Acceptor numbers of solvent and other components. The method uses fast GGA-level DFT calculations compared to previously used expensive, experimental data dependent methods. This method can be used to screen for unexplored stable solvents among the large number of known organic compounds to design novel high voltage stable electrolytes.
Rechargeable redox flow batteries with serpentine flow field designs have been demonstrated to deliver higher current density and power density in medium and large-scale stationary energy storage applications. Nevertheless, the fundamental mechanisms involved with improved current density in flow batteries with flow field designs have not been understood. Here we report a maximum current density concept associated with stoichiometric availability of electrolyte reactant flow penetration through the porous electrode that can be achieved in a flow battery system with a "zero-gap"serpentine flow …
This paper presents a combined theoretical and experimental investigation of aqueous near-neutral electrolytes based on chloride salts for rechargeable zinc-air batteries (ZABs). The resilience of near-neutral chloride electrolytes in air could extend ZAB lifetime, but theory-based simulations predict that such electrolytes are vulnerable to other challenges including pH instability and the unwanted precipitation of mixed zinc hydroxide chloride products. In this work, we combine theory-based simulations with experimental methods such as full cell cycling, operando pH measurements, ex-situ XRD…
Recently, dinitriles (NC(CH2)nCN) and especially adiponitrile (ADN, n=4) have attracted the attention as secure electrolyte solvents due to their chemical stability, high boiling points, high flash points and low vapor pressure. The good solvating properties of ADN toward lithium salts and its high electrochemical stability (~ 6V vs. Li/Li+) make it suitable for safer Li-ions cells without performances loss. In this study, ADN is used as a single electrolyte solvent with lithium bis(trimethylsulfonyl)imide (LiTFSI). This electrolyte allows the use of aluminum collectors as almost no corrosion …
Several active areas of research in novel energy storage technologies, including three-dimensional solid state batteries and passivation coatings for reactive battery electrode components, require conformal solid state electrolytes. We describe an atomic layer deposition (ALD) process for a member of the lithium phosphorus oxynitride (LiPON) family, which is employed as a thin film lithium-conducting solid electrolyte. The reaction between lithium tert-butoxide (LiO$^t$Bu) and diethyl phosphoramidate (DEPA) produces conformal, ionically conductive thin films with a stoichiometry close to Li$_2…
All-solid-state Li-ion batteries promise safer electrochemical energy storage with larger volumetric and gravimetric energy densities. A major concern is the limited electrochemical stability of solid electrolytes and related detrimental electrochemical reactions, especially because of our restricted understanding. Here we demonstrate for the argyrodite, garnet and NASICON type solid electrolytes, that the favourable decomposition pathway is indirect rather than direct, via (de)lithiated states of the solid electrolyte, into the thermodynamically stable decomposition products. The consequence …
Electrolyte reduction products form the solid-electrolyte interphase (SEI) on negative electrodes of lithium-ion batteries. Even though this process practically stabilizes the electrode-electrolyte interface, it results in continued capacity-fade limiting lifetime and safety of lithium-ion batteries. Recent atomistic and continuum theories give new insights into the growth of structures and the transport of ions in the SEI. The diffusion of neutral radicals has emerged as a prominent candidate for the long-term growth mechanism, because it predicts the observed potential dependence of SEI grow…
A precise understanding of solvation is essential for rational search and design of electrolytes that can meet performance demands in Li-ion and beyond Li-ion batteries. In the context of Li-O$_2$ batteries, ion pairing is decisive in determining battery capacity via the solution mediated discharge mechanism without compromising heavily on electrolyte stability. We argue that models based on coordination numbers of the counterion in the first solvation shell are inadequate at describing the extent of ion pairing, especially at higher salt concentrations, and are often not consistent with exper…
Redox flow batteries (RFBs) have gained popularity as large-scale energy storage systems for wind and solar powered grids. Modern RFB systems are based on highly corrosive and/or flammable electrolytes. Organic redox active species for RFBs are gaining commercial traction, but there is a trade-off in choosing aqueous or non-aqueous electrolytes in terms of rate capabilities, energy density, safety and cost. While modification of organic redox molecules to mitigate these issues is prevalent in the literature, the search for novel electrolyte systems is scarce. Here we present microemulsion-base…
The electrolytes used in Lithium Ion Batteries (LIBs) such as LiBF4, LiPF6 etc. are Li-salts of some complex anions, BF4-, PF6- etc. The investigation shows that the vertical detachment energy (VDE) of these anions exceeds to that of halogen, and therefore they behave as superhalogen anions. Consequently, it might be possible to design new electrolytic salts using other superhalogen anions. We have explored this possibility using Li-salts of various superhalogen anions such as BO2-, AlH4-, TiH5- and VH6- as well as hyperhalogen anions, BH4-y(BH4)y-(y = 1 to 4). Our density functional calculati…
In lithium ion batteries, Li+ intercalation and processes associated with passivation of electrodes are governed by applied voltages, which are in turn associated with free energy changes of Li+ transfer (Delta G_t) between the solid and liquid phases. Using ab initio molecular dynamics (AIMD) and thermodynamic integration techniques, we compute Delta G_t for the virtual transfer of a Li+ from a LiC(6) anode slab, with pristine basal planes exposed, to liquid ethylene carbonate confined in a nanogap. The onset of delithiation, at Delta G_t=0, is found to occur on LiC(6) anodes with negatively …
Aqueous zinc-air batteries (ZABs) are a low-cost, safe, and sustainable technology for stationary energy storage. ZABs with pH-buffered near-neutral electrolytes have the potential for longer lifetime compared to traditional alkaline ZABs due to the slower absorption of carbonates at non-alkaline pH values. However, existing near-neutral electrolytes often contain halide salts, which are corrosive and threaten the precipitation of ZnO as the dominant discharge product. This paper presents a method for designing halide-free aqueous ZAB electrolytes using thermodynamic descriptors to computation…
Nonaqueous aluminum-ion batteries are an interesting emerging energy storage technology, offering a plethora of advantages over existing grid energy storage solutions. Carbonaceous and graphitic materials are an appealing cathode material in this system, thanks to their low cost and excellent rate capabilities. The phenomenon of poor Coulombic efficiency in the first cycle, however, is a known issue among some types of carbons, the reasons for which are yet to be fully understood. In this work, we propose that such processes are caused by the formation of a solid-electrolyte interphase, in a s…
Dendrite free electrodeposition of lithium metal is necessary for the adoption of high energy density rechargeable lithium metal batteries. Here, we demonstrate a new mechanism of using a liquid crystalline electrolyte to suppress dendrite growth with a lithium metal anode. A nematic liquid crystalline electrolyte modifies the kinetics of electrodeposition by introducing additional overpotential due to its bulk distortion and anchoring free energy. By extending the phase-field model, we simulate the morphological evolution of the metal anode and explore the role of bulk distortion and anchorin…
Lithium-metal batteries employing concentrated glyme-based electrolytes and different cathode chemistries are herein evaluated in view of a safe use of the highly energetic alkali-metal anode. Indeed, diethylene-glycol dimethyl-ether (DEGDME) and triethylene-glycol dimethyl-ether (TREGDME) dissolving lithium bis(trifluoromethanesulfonyl)imide (LiTFSI) and lithium nitrate (LiNO3) in concentration approaching the solvents saturation limit are used in lithium batteries employing either a conversion sulfur-tin composite (S:Sn 80:20 w/w) or a Li+ (de-)insertion LiFePO4 cathode. Cyclic voltammetry (…
The lithium metal-solid-state electrolyte interface plays a critical role in the performance of solid-state batteries. However, operando characterization of the buried interface morphology in solid-state cells is particularly difficult because of the lack of direct optical access. Destructive techniques that require isolating the interface inadvertently modify the interface and cannot be used for operando monitoring. In this work, we introduce the concept of thermal wave sensing using modified 3-omega sensors that is attached to the outside of the lithium metal-solid state cells to non-invasiv…
The concept of green in a battery involves the chemical nature of electrodes and electrolytes as well as the economic sustainability of the cell. Although these aspects are typically discussed separately, they are deeply interconnected: indeed, a new electrolyte can allow the use of different cathodes with higher energy, lower cost or more pronounced environmental compatibility. We focus on alternative class of electrolyte solutions for lithium batteries formed by dissolving LiX salts in glyme solvents, i.e., organic ethers with the molecular formula CH3O[CH2CH2O]nCH3 differing by chain length…
The existence of passivating layers at the interfaces is a major factor enabling modern lithium-ion (Li-ion) batteries. Their properties determine the cycle life, performance, and safety of batteries. A special case is the solid electrolyte interphase (SEI), a heterogeneous multi-component film formed due to the instability and subsequent decomposition of the electrolyte at the surface of the anode. The SEI acts as a passivating layer that hinders further electrolyte disintegration, which is detrimental to the Coulombic efficiency. In this work, we use first-principles simulations to investiga…
The quest for safe high-energy batteries with "5V-class" cathodes and lithium metal anodes drives research into solid electrolytes. However, reasons for the large charge transfer resistances -- the major bottleneck of all-solid-state batteries -- are still debated. In this article, we explore the processes in incompressible solid electrolytes between blocking electrodes by theory-based continuum modeling and numerical simulations. We investigate the experimentally observed wide space-charge-zones in solid electrolytes, which are a possible cause for the high interfacial resistances. On time sc…
The performance of modern lithium-sulfur (Li/S) battery systems critically depends on the electrolyte and solvent compositions. For fundamental molecular insights and rational guidance of experimental developments, efficient and sufficiently accurate molecular simulations are thus in urgent need. Here, we construct a molecular dynamics (MD) computer simulation model of representative state-of-the art electrolyte-solvent systems for Li/S batteries constituted by lithium-bis(trifluoromethane)sulfonimide (LiTFSI) and LiNO3 electrolytes in mixtures of the organic solvents 1,2-dimethoxyethane (DME)…
Lithium fluorinated carbon is one of the most promising chemistries for high-energy-density primary energy storage systems in applications where rechargeability is not required. Though Li/CFx demonstrates high energy density under ambient conditions, achieving such a high energy density when exposed to subzero temperatures remains a challenge, particularly under high current density. Here, we report a liquefied gas electrolyte with an anion-pair solvation structure based on dimethyl ether with a low melting point and low viscosity, leading to high ionic conductivity between a wide temperature …
In this article the Butler-Volmer equation used in describing Lithium-ion (Li-ion) batteries is discussed. First, a complete mathematical model based on a macro-homogeneous approach developed by Neuman is presented. Two common mistakes found in the literature regarding a sign in a boundary conditions and the use of the transfer coefficient are mentioned. The paper focuses on the form of the Butler-Volmer equation in the model. It is shown how practical problems can be avoided by taking care in the form used, particularly to avoid difficulties when the solid particle in the electrodes approache…
Metal-air batteries are among the most promising next-generation energy storage devices. Relying on abundant materials and offering high energy densities, potential applications lie in the fields of electro-mobility, portable electronics, and stationary grid applications. Now, research on secondary zinc-air batteries is revived, which are commercialized as primary hearing aid batteries. One of the main obstacles for making zinc-air batteries rechargeable is their poor lifetime due to the degradation of alkaline electrolyte in contact with atmospheric carbon dioxide. In this article, we present…
A diffuse-interface model for predicting the evolution of metallic negative electrodes and interfacial voids in solid-state batteries with homogeneous and polycrystalline solid electrolyte separators
In this article, we derive and discuss a physics-based model for impedance spectroscopy of lithium batteries. Our model for electrochemical cells with planar electrodes takes into account the solid-electrolyte interphase (SEI) as porous surface film. We present two improvements over standard impedance models. Firstly, our model is based on a consistent description of lithium transport through electrolyte and SEI. We use well-defined transport parameters, e.g., transference numbers, and consider convection of the center-of-mass. Secondly, we solve our model equations analytically and state the …
Aprotic alkali metal-oxygen batteries are widely considered to be promising high specific energy alternatives to Li-ion batteries. The growth and dissolution of alkali metal oxides such as Li2O2 in Li-O2 batteries and NaO2 and KO2 in Na- and K-O2 batteries, respectively, is central to the discharge and charge processes in these batteries. However, crystal growth and dissolution of the discharge products, especially in aprotic electrolytes, is poorly understood. In this work, we chose the growth of NaO2 in Na-O2 batteries as a model system and show that there is a strong correlation between the…
Solid-state batteries (SSBs) can offer a paradigm shift in battery safety and energy density. Yet, the promise hinges on the ability to integrate high-performance electrodes with state-of-the-art solid electrolytes. For example, lithium (Li) metal, the most energy-dense anode candidate, suffers from severe interfacial chemomechanical issues that lead to cell failure. Li alloys of In/Sn are attractive alternatives, but their exploration has mostly been limited to the low capacity(low Li content)and In rich Li$_x$In (x$\leq$0.5). Here, the fundamental electro-chemo-mechanical behavior of Li-In a…
Oxidative decomposition of organic-solvent-based liquid electrolytes at cathode material interfaces has been identified as a main reason for rapid capacity fade in high-voltage lithium ion batteries. The evolution of "cathode electrolyte interphase: (CEI) films, partly or completely consisting of electrolyte decomposition products, has also recently been demonstrated to be correlated with battery cycling behavior at high potentials. Using Density Functional Theory (DFT) calculations, the hybrid PBE0 functional, and the (001) surfaces of spinel oxides as models, we examine these two interrelate…
The penetration of dendrites in ceramic lithium conductors severely constrains the development of solid-state batteries (SSBs) while its nanoscopic origin remain unelucidated. We develop an in-situ nanoscale electrochemical characterization technique to reveal the nanoscopic lithium dendrite growth kinetics and use it as a guiding tool to unlock the design of interfaces for dendrite-proof SSBs. Using Li7La3Zr2O12 (LLZO) as a model system, in-situ nanoscopic dendrite triggering measurements, ex-situ electro-mechanical characterizations, and finite element simulations are carried out which revea…
Lithium--sulfur (Li/S) batteries are regarded as one of the most promising energy storage devices beyond lithium-ion batteries because of their high energy density of 2600 Wh/kg and an affordable cost of sulfur. Meanwhile, some challenges inherent to Li/S batteries remain to be tackled, for instance, the polysulfide (PS) shuttle effect, the irreversible solidification of Li$_2$S, and the volume expansion of the cathode material during discharge. On the molecular level, these issues originate from the structural and solubility behavior of the PS species in bulk and in the electrode confinement.…
The world is at the cusp of a new era where pivotal importance is being attached to the development of sustainable and high-performance energy storage systems. Potassium-ion batteries are deemed not only as cheap battery candidates, but also as the penultimate high-voltage energy storage systems within the monovalent-cation chemistries. However, their performance and sustainability are undermined by the lack of suitable electrolytes for high-voltage operation particularly due to the limited availability of cathode materials. Here, the potential of ionic liquids based on potassium bis(trifluoro…
We present a mechanistic theory for predicting void evolution in the Li metal electrode during the charge and discharge of all-solid-state battery cells. A phase field formulation is developed to model vacancy annihilation and nucleation, and to enable the tracking of the void-Li metal interface. This is coupled with a viscoplastic description of Li deformation, to capture creep effects, and a mass transfer formulation accounting for substitutional (bulk and surface) Li diffusion and current-driven flux. Moreover, we incorporate the interaction between the electrode and the solid electrolyte, …
Lithium-air batteries have been considered as ultimate solutions for the power source of long-range electrified transportation, but state-of-the-art prototypes still suffer from short cycle life, low efficiency and poor power output. Here, a lithium-bromine rechargeable fuel cell using highly concentrated bromine catholytes is demonstrated with comparable specific energy, improved power density, and higher efficiency. The cell is similar in structure to a hybrid-electrolyte Li-air battery, where a lithium metal anode in nonaqueous electrolyte is separated from aqueous bromine catholytes by a l…
Differentiable OPLS Force Field Parameterization for Ionic Electrolytes and High-Throughput Application to Lithium-ion Batteries
Tsinghua Shenzhen International Graduate School, Tsinghua University（清华大学深圳国际研究生院）；CATL 21C Innovation Laboratory, Contemporary Amperex Technology Ltd.（宁德时代21世纪创新实验室）；Department of Physics, Institute of Quantum Science and Technology, Shanghai University（上海大学量子科学与技术研究院物理系）；Shenzhen All-Solid-State Lithium Battery Electrolyte Engineering Research Center, Institute of Materials Research (IMR), Tsinghua Shenzhen International Graduate School, Tsinghua University（清华大学深圳国际研究生院材料研究院深圳全固态锂电池电解质工程研究中心）
As one of the most promising next-generation energy storage device, lithium metal batteries have been extensively investigated. However, the poor safety issue and undesired lithium dendrites growth hinder the development of lithium metal batteries. The application of solid state electrolytes has attracted increasing attention as they can solve the safety issue and partly inhibit the growth of lithium dendrites. Polyethylene oxide (PEO)-based electrolytes are very promising due to their enhanced safety and excellent flexibility. However, PEO-based electrolytes suffer from low ionic conductivity…
In this work we address Li-ion diffusion in thio-LISICON materials and in their oxide counterparts, exploring both the orthorhombic and tetragonal phases of Li10GeP2S12(LGPS) and Li10GeP2O12(LGPO) through extended Car-Parrinello molecular dynamics in the canonical and isobaric-isothermal ensemble. The (quasi-)orthorhombic and tetragonal phases are studied both for the oxide and for the sulfide, with the aim of comparing their conductivity with the same approach; out of these four case studies, tetragonal LGPO has not been reported and, while dynamically stable, it sits (0.04 Ha/formula unit) a…
Li+ transport within a solid electrolyte interphase (SEI) in lithium ion batteries has challenged molecular dynamics (MD) studies due to limited compositional control of that layer. In recent years, experiments and ab initio simulations have identified dilithium ethylene dicarbonate (Li2EDC) as the dominant component of SEI layers. Here, we adopt a parameterized, non-polarizable MD force field for Li2EDC to study transport characteristics of Li+ in this model SEI layer at moderate temperatures. The observed correlations are consistent with recent MD results using a polarizable force field, sug…
Among the 'beyond Li-ion' battery chemistries, nonaqueous Li-O$_2$ batteries have the highest theoretical specific energy and as a result have attracted significant research attention over the past decade. A critical scientific challenge facing nonaqueous Li-O$_2$ batteries is the electronically insulating nature of the primary discharge product, lithium peroxide, which passivates the battery cathode as it is formed, leading to low ultimate cell capacities. Recently, strategies to enhance solubility to circumvent this issue have been reported, but rely upon electrolyte formulations that furthe…
We present theoretical analysis on why and how rechargeable metal-air type batteries can be made significantly safer and more practical by utilizing CO2/oxalate conversions instead of O2/peroxide or O2/hydroxide ones, in the positive electrode. Metal-air batteries, such as the Li-air one, may have very large energy densities, comparable to that of gasoline, theoretically allowing for long range all-electric vehicles. There are, however, still significant challenges, especially related to the safety of their underlying chemistries, the robustness of their recharging and the need of supplying hi…
Next-generation high-energy-density batteries require ideally stable metal anodes, for which smooth metal deposits during battery recharging are considered a sign of interfacial stability that can ensure high efficiency and long cycle life. With the recent successes, whether the absolute morphological stability guarantees absolute electrochemical stability and safety emerges as a critical question to be investigated in systematic experiments under practical conditions. Here, we use the ideally stable ingot-type sodium metal anode as a model system to identify the fast-charging limits, i.e. hig…
Fluoroethylene carbonate (FEC) shows promise as an electrolyte additive for improving passivating solid-electrolyte interphase (SEI) films on silicon anodes used in lithium ion batteries (LIB). We apply density functional theory (DFT), ab initio molecular dynamics (AIMD), and quantum chemistry techniques to examine excess-electron-induced FEC molecular decomposition mechanisms that lead to FEC-modified SEI. We consider one- and two-electron reactions using cluster models and explicit interfaces between liquid electrolyte and model Li(x)Si(y) surfaces, respectively. FEC is found to exhibit more…
The lithium-air (Li-O$_2$) battery has received enormous attention as a possible alternative to current state-of-the-art rechargeable Li-ion batteries given their high theoretical specific energy. However, the maximum discharge capacity in nonaqueous Li-O$_2$ batteries is limited to a small fraction of its theoretical value due to the insulating nature of lithium peroxide, Li$_2$O$_2$, the battery$'$s primary discharge product. In this work, we show that the inclusion of trace amounts of electrolyte additives, such as H$_2$O, significantly improve the capacity of the Li-O$_2$ battery. These ad…
A major bottleneck for the development of Mg batteries is the identification of liquid electrolytes that are simultaneously compatible with the Mg-metal anode and high-voltage cathodes. One strategy to widen the stability windows of current non-aqueous electrolytes is to introduce protective coating materials at the electrodes, where coating materials are required to exhibit swift Mg transport. In this work, we use a combination of first-principles calculations and ion-transport theory to evaluate the migration barriers for nearly 27 Mg-containing binary, ternary, and quaternary compounds span…
This paper presents the current state of mathematical modelling of the electrochemical behaviour of lithium-ion batteries as they are charged and discharged. It reviews the models developed by Newman and co-workers, both in the cases of dilute and moderately-concentrated electrolytes and indicates the modelling assumptions required for their development. Particular attention is paid to the interface conditions imposed between the electrolyte and the active electrode material; necessary conditions are derived for one of these, the Butler-Volmer relation, in order to ensure physically realistic …
A new nanofibrous material, consisting of a conductive carbon core and an external layer made of vanadium oxide, has been studied as a cathode for aluminium-ion batteries. The material enables a mixed-ion intercalation mechanism, resulting in the alternating insertion of $\text{Al}^{3+}$ and $\text{AlCl}_4^-$ in the $\text{V}_2\text{O}_5$ and carbon layers, respectively. This is a highly desirable feature for cathode materials which may increase the energy density of future batteries by optimising the utilisation of the electrolyte.
