Recent computational and laboratory experiments have shown that the brittle-ductile transitions in metallic glasses such as Vitreloy1 are strongly sensitive to the initial effective disorder (or "fictive") temperature. Glasses with lower effective temperatures are weak and brittle; those with higher effective temperatures are strong and ductile. The analysis of this phenomenon presented here examines the onset of fracture at the tip of a slightly rounded notch as predicted by the shear-transformation-zone (STZ) theory of spatially varying plastic deformation. The central ingredient of this analysis is an approximation for the dynamics of the plastic zone formed by stress concentration at the notch tip. This zone first shields the tip but then breaks down suddenly producing a discontinuous transition between brittle and ductile failure, in agreement with the numerical and experimental observations.
In ordinary solids, material disorder is known to increase the size of the process zone in which stress concentrates at the crack tip, causing a transition from localized to diffuse failure. Here, we report experiments on disordered 2D lattices, derived from frictional particle packings, in which the mean coordination number $\langle z \rangle$ of the underlying network provides a similar control. Our experiments show that tuning the connectivity of the network provides access to a range of behaviors from brittle to ductile failure. We elucidate the cooperative origins of this transition using…
The fracture properties of as-cast TiVNbTa, a refractory high-entropy alloy (RHEA), were investigated using four-point bending tests from -139C to 20C under a strain-rate of 10-3 s-1. From those tests and fractography, the conditional fracture toughness values and the brittle-to-ductile transition temperature were obtained. The brittle-to-ductile transition temperature was between -47C to -27C, which gives an estimated activation energy value of 0.52+-0.09 eV for the alloy. This study provides a preliminary understanding of the nature of dislocation motion in a relatively ductile RHEA.
Molecular-dynamics simulations of fracture in metallic glass-like systems are observed to undergo embrittlement due to a small change in interatomic potential. This change in fracture toughness, however, is not accompanied by a corresponding change in flow stress. Theories of brittle fracture proposed by Freund and Hutchinson indicate that strain rate sensitivity is the controling physical parameter in these cases. A recent theory of viscoplasticity in this class of solids by Falk and Langer further suggests that the change in strain rate sensitivity corresponds to a change in the susceptibili…
We introduce a lattice model able to describe damage and yielding in heterogeneous materials ranging from brittle to ductile ones. Ductile fracture surfaces, obtained when the system breaks once the strain is completely localized, are shown to correspond to minimum energy surfaces. The similarity of the resulting fracture paths to the limits of brittle fracture or minimum energy surfaces is quantified. The model exhibits a smooth transition from brittleness to ductility. The dynamics of yielding exhibits avalanches with a power-law distribution.
Tearing a thin sheet by forcing a rigid object through it leads to complex crack morphologies; a single oscillatory crack arises when a tool is driven laterally through a brittle sheet, while two diverging cracks and a series of concertina-like folds forms when a tool is forced laterally through a ductile sheet. On the other hand, forcing an object perpendicularly through the sheet leads to radial petal-like tears in both ductile and brittle materials. To understand these different regimes we use a combination of experiments, simulations and simple theories. In particular, we describe the tran…
A continuum model of fracture that describes, in principle, the propagation and interaction of arbitrary distributions of cracks and voids with evolving topology without a fracture criterion is developed. It involves a 'law of motion' for crack-tips, primarily as a kinematical consequence coupled with thermodynamics. Fundamental kinematics endows the crack-tip with a topological charge. This allows the association of a kinematical conservation law for the charge, resulting in a fundamental evolution equation for the crack-tip field, and in turn the crack field. The vectorial crack field degrad…
The fracture behavior of brittle and ductile materials can be strongly influenced by thermal fluctuations, especially in micro- and nano-devices as well as in rubberlike and biological materials. However, temperature effects, in particular on the brittle-to-ductile transition, still require a deeper theoretical investigation. As a step in this direction we propose a theory, based on equilibrium statistical mechanics, able to describe the temperature dependent brittle fracture and brittle-to-ductile transition in prototypical discrete systems consisting in a lattice with breakable elements. Con…
When considering grinding of minerals, scaling effect induces competition between plastic deformation and fracture in brittle solids. The competition can be sketched by a critical size of the material, which characterizes the ductile-brittle transition. A first approach using Vickers indentation gives a good approximation of the critical size through an extrapolation from the macroscopic to the microscopic scales. Nanoindentation tests confirm this experimental value. According to the grain size compared to the indent size, it can reasonably be said that the mode of damage is deformation-induc…
Understanding the fracture toughness of glasses is of prime importance for science and technology. We study it here using extensive atomistic simulations in which the interaction potential, glass transition cooling rate and loading geometry are systematically varied, mimicking a broad range of experimentally accessible properties. Glasses' nonequilibrium mechanical disorder is quantified through $A_{\rm g}$, the dimensionless prefactor of the universal spectrum of nonphononic excitations, which measures the abundance of soft glassy defects that affect plastic deformability. We show that while …
Quantitative understanding of the fracture toughness of metallic glasses, including the associated ductile-to-brittle transitions, is not yet available. Here we use a simple model of plastic deformation in glasses, coupled to an advanced Eulerian level set formulation for solving complex free boundary problems, to calculate the fracture toughness of metallic glasses as a function of the degree of structural relaxation corresponding to different annealing times near the glass temperature. Our main result indicates the existence of an elasto-plastic crack tip instability for sufficiently relaxed…
We conisder the brittle versus ductile behavior of aluminum in the framework of the Peierls-model analysis of dislocation emission from a crack tip. To this end, we perform first-principles quantum mechanical calculations for the unstable stacking energy $γ_{us}$ of aluminum along the Shockley partial slip route. Our calculations are based on density functional theory and the local density approximation and include full atomic and volume relaxation. We find that in aluminum $γ_{us} = 0.224$ J/m$^2$. Within the Peierls-model analysis, this value would predict a brittle solid which poses an inte…
Understanding ductility or brittleness of monolithic bulk metallic glasses (BMGs) requires detailed knowledge of the amorphous structure. The medium range order (MRO) of ductile Pd$_{40}$Ni$_{40}$P$_{20}$ and brittle Zr$_{52.5}$Cu$_{17.9}$Ni$_{14.6}$Al$_{10}$Ti$_5$ (Vit105) was characterized prior to and after notched 3-point bending tests using variable-resolution fuctuation electron microscopy. Here we show the presence of a second larger MRO correlation length in the ductile material which is not present in the brittle material. A comparison with literature suggests that the larger correlat…
We perform a large-scale statistical analysis (> 2000 independent simulations) of the elongation and rupture of gold nanowires, probing the validity and scope of the recently proposed ductile-to-brittle transition that occurs with increasing nanowire length [Wu et. al., Nano Lett., 12, 910-914 (2012)]. To facilitate a high-throughput simulation approach, we implement the second-moment approximation to the tight-binding (TB-SMA) potential within HOOMD-Blue, a molecular dynamics package which runs on massively parallel graphics processing units (GPUs). In a statistical sense, we find that the na…
We study two closely related, nonlinear models of a viscoplastic solid. These models capture essential features of plasticity over a wide range of strain rates and applied stresses. They exhibit inelastic strain relaxation and steady flow above a well defined yield stress. In this paper, we describe a first step in exploring the implications of these models for theories of fracture and related phenomena. We consider a one dimensional problem of decohesion from a substrate of a membrane that obeys the viscoplastic constitutive equations that we have constructed. We find that, quite generally, w…
Fracture in aluminum alloys with precipitates involves at least two mechanisms, namely, ductile fracture of the aluminum-rich matrix and brittle fracture of the precipitates. In this work, a coupled crystal plasticity-phase field model for mixed ductile-brittle failure modes is formulated and used to investigate the effect of precipitate morphology and size distribution on damage evolution in aluminum alloys. A thermodynamically consistent framework for elastic and plastic work dissipation in the fracture process zone is used to formulate the coupled constitutive behavior for brittle and ducti…
Molecular dynamics simulations have been performed to understand the influence of temperature on the tensile deformation and fracture behavior of $<$111$>$ BCC Fe nanowires. The simulations have been carried out at different temperatures in the range 10-1000 K employing a constant strain rate of $1\times$ $10^8$ $s^{-1}$. The results indicate that at low temperatures (10-375 K), the nanowires yield through the nucleation of a sharp crack and fails in brittle manner. On the other hand, nucleation of multiple 1/2$<$111$>$ dislocations at yielding followed by significant plastic deformation leadi…
Temperature-activated dislocation avalanches signaling brittle-to-ductile transition in BCC micropillars
School of Mechanics & Engineering Science, Shanghai University（上海大学力学与工程科学学院）；Department of Mechanical & Aerospace Engineering, University of Miami（迈阿密大学机械与航空航天工程系）；School of Physics, Sun Yat-sen University（中山大学物理学院）；Department of Mechanical & Aerospace Engineering, University of California Los Angeles（加州大学洛杉矶分校机械与航空航天工程系）
A Mesoscale Model for Interface-Mediated Plasticity: Investigation of Ductile and Brittle Fracture
City University of Hong Kong（香港城市大学）；University of California, Los Angeles（加州大学洛杉矶分校）；The University of Hong Kong（香港大学）；University of Birmingham（伯明翰大学）
Magneto-plasticity occurs when a weak magnetic field alters material plasticity and offers a viable solution to enhance ductile-mode cutting of brittle materials. This study demonstrates the susceptibility of non-magnetic single-crystal calcium fluoride (CaF2) to the magneto-plastic effect. The influence of magneto-plasticity on CaF2 was confirmed in micro-deformation tests under a weak magnetic field of 20 mT. The surface pile-up effect was weakened by 10-15 nm along with an enlarged plastic zone and suppressed crack propagation under the influence of the magnetic field. Micro-cutting tests a…
Soft amorphous materials are viscoelastic solids ubiquitously found around us, from clays and cementitious pastes to emulsions and physical gels encountered in food or biomedical engineering. Under an external deformation, these materials undergo a noteworthy transition from a solid to a liquid state that reshapes the material microstructure. This yielding transition was the main theme of a workshop held from January 9 to 13, 2023 at the Lorentz Center in Leiden. The manuscript presented here offers a critical perspective on the subject, synthesizing insights from the various brainstorming ses…
The toughness of a polymer material can increase significantly if two networks are combined into one material. This toughening effect is a consequence of a transition from a brittle to a ductile failure response. Although this transition and the accompanying toughening effect have been demonstrated in hydrogels first, the concept has been proven effective in elastomers and in macroscopic composites as well. This suggests that the transition is not caused by a specific molecular architecture, but rather by a general physical principle related to the mechanical interplay between two interpenetra…
As a potential building block for the next generation of devices or multifunctional materials that are spreading almost every technology sector, one-dimensional (1D) carbon nanomaterial has received intensive research interests. Recently, a new ultra-thin diamond nanothread (DNT) has joined this palette, which is a 1D structure with poly-benzene sections connected by Stone-Wales (SW) transformation defects. Using large-scale molecular dynamics simulations, we found that this sp3 bonded DNT can transit from a brittle to a ductile characteristic by varying the length of the poly-benzene sections…
We present a model for the thermally activated propagation of cracks in elastic matrices. The propagation is considered as a subcritical phenomenon, the kinetics of which being described by an Arrhenius law. In this law, we take the thermal evolution of the crack front into account, assuming that a portion of the released mechanical energy is transformed into heat in a plastic process zone. We show that such a model leads to a two-phase crack propagation: a first phase at low velocity in which the temperature elevation is of little effect and the propagation is mainly governed by the mechanica…
Spatially heterogeneous relaxational dynamics and the evolution of recoverable strain following flow cessation of a ductile nanocolloidal glass
Johns Hopkins University（约翰斯·霍普金斯大学）；University of Illinois Urbana-Champaign（伊利诺伊大学厄巴纳-香槟分校）；Argonne National Laboratory（阿贡国家实验室）；University of Ottawa（渥太华大学）
This paper presents a framework for modeling failure in quasi-brittle geomaterials under different loading conditions. A micromechanics-based model is proposed in which the field variables are linked to physical mechanisms at the microcrack level: damage is related to the growth of microcracks, while plasticity is related to the frictional sliding of closed microcracks. Consequently, the hardening/softening functions and parameters entering the free energy follow from the definition of a single degradation function and the elastic material properties. The evolution of opening microcracks in te…
Amorphous solids display a ductile to brittle transition as the kinetic stability of the quiescent glass is increased, which leads to a material failure controlled by the sudden emergence of a macroscopic shear band in quasi-static protocols. We numerically study how finite deformation rates influence ductile and brittle yielding behaviors using model glasses in two and three spatial dimensions. We find that a finite shear rate systematically enhances the stress overshoot of poorly-annealed systems, without necessarily producing shear bands. For well-annealed systems, the non-equilibrium disco…
Understanding the strengthening and deformation mechanisms in refractory high-entropy alloys (HEAs), proposed as new high-temperature material, is required for improving their typically insufficient room-temperature ductility. Here, density-functional theory simulations and a continuum mechanics analysis were conducted to systematically investigate the competition between cleavage decohesion and dislocation emission from a crack tip in the body-centered cubic refractory HEAs HfNbTiZr, MoNbTaVW, MoNbTaW, MoNbTiV, and NbTiVZr. This crack-tip competition is evaluated for tensile loading and a tot…
Earthquakes are complex phenomena characterized by some fundamental seismic laws. However, under the framework of brittle fracture in disordered material, these universal scaling behaviors, especially for critical exponents, are still far from understood. In this Letter, we study avalanches in compression of a nonbrittle material, the ductile metallic glass foam. In addition to elasticity and disorder, more complex inelastic effects can be also introduced by strain localization in cellular structures. We show that different from brittle fracture, the additional shear-banding interactions resul…
Numerous measurements showed that the crack tip opening angle (CTOA) is nearly constant upon stable ductile fracture in Al alloys which widely used in modern transportation industry. The atomic structure of the very tip of a crack front has remained unknown, however. We have carried out a first-principles density functional theory study to reveal the precise alignment of atoms near the crack tip in single-crystalline Al. The calculations demonstrate that the CTOA increases with the opening displacement, thus the observed constant CTOA in millimeter scale is an entirely plastic effect during du…
Beijing Computational Science Research Center（北京计算科学研究中心）；Ningbo Institute of Materials Technology and Engineering, Chinese Academy of Sciences（中国科学院宁波材料技术与工程研究所）；State Key Laboratory of Advanced Marine Materials, Ningbo Institute of Materials Technology and Engineering, Chinese Academy of Sciences（中国科学院宁波材料技术与工程研究所先进海洋材料国家重点实验室）；College of Materials & Environmental Engineering, Hangzhou Dianzi University（杭州电子科技大学材料与环境工程学院）；State Key Laboratory of Nonlinear Mechanics, Institute of Mechanics, Chinese Academy of Sciences（中国科学院力学研究所非线性力学国家重点实验室）；School of Engineering Science, University of Chinese Academy of Sciences（中国科学院大学工程科学学院）
High strength and high toughness are usually mutually exclusive in engineering materials. Improving the toughness of strong but brittle materials like ceramics thus relies on the introduction of a metallic or polymeric ductile phase to dissipate energy, which conversely decreases the strength, stiffness, and the ability to operate at high temperature. In many natural materials, toughness is achieved through a combination of multiple mechanisms operating at different length scales but such structures have been extremely difficult to replicate. Building upon such biological structures, we demons…
Cracking the case: fluctuations enhance ductility in refractory alloys
École Polytechnique Fédérale de Lausanne (EPFL)（洛桑联邦理工学院）；Laboratory of materials design and simulation (MADES), Institute of Materials, École Polytechnique Fédérale de Lausanne (EPFL)（洛桑联邦理工学院材料研究所材料设计与模拟实验室）；National Centre for Computational Design and Discovery of Novel Materials (MARVEL), École Polytechnique Fédérale de Lausanne (EPFL)（洛桑联邦理工学院新型材料计算设计与发现国家中心）；EMPA - Swiss Federal Laboratories for Materials Science and Technology（瑞士联邦材料科学与技术研究院）；Laboratory for Multiscale Modeling in Mechanics (LAMMM), Institute of Mechanical Engineering, École Polytechnique Fédérale de Lausanne (EPFL)（洛桑联邦理工学院机械工程学院多尺度力学建模实验室）；School of Engineering, Brown University, Providence, RI 02906 USA（布朗大学工程学院）
Micro- or minor alloying of metallic glasses is of technological interest. An originally ductile Pd-based monolithic bulk metallic glass (Pd$_{40}$Ni$_{40}$P$_{20}$) was selectively manipulated by additions of Fe or Co. The alloying effects were extreme, showing either exceptional ductility upon Co addition or immediate catastrophic failure upon Fe addition when tested under uniaxial compression or 3-point bending. The amorphous structure was characterized prior to deformation with respect to its medium-range order (MRO) using variable resolution fluctuation electron microscopy (VR-FEM). We ob…
We report results of statistical and dynamic analysis of the serrated stress-time curves obtained from compressive constant strain-rate tests on two metallic glass samples with different ductility levels in an effort to extract hidden information in the seemingly irregular serrations. Two distinct types of dynamics are detected in these two alloy samples. The stress-strain curve corresponding to the less ductile $Zr_{65}Cu_{15}Ni_{10}Al_{10}$ alloy is shown to exhibit finite correlation dimension and a positive Lyapunov exponent, suggesting that the underlying dynamics is chaotic. In contrast,…
An atomistic understanding of annealing embrittlement is a longstanding issue for metallic glasses, which is still lacking due to the insurmountable gap between the thermal history of atomic models and laboratory-made samples. Here, based on a thermal-cycling annealing method that can vary the effective quenching rate over ten orders of magnitude, we perform an atomistic study of the ductile-brittle transition in a ternary model metallic glass, which can be keyed to the annealing embrittlement in bulk metallic glasses. We reveal that thermal annealing can effectively obliterate thermally activ…
New metallic glasses containing La or Ce have been introduced that have dynamic properties bordering on extremes of conventional metallic glasses. This provides opportunity to test trends or correlations established before in molecular and polymeric glass-formers if exist the same exist in the broader family of metallic glasses. Due to the drastically different chemical and physical structure of metallic glass-formers than soft matter, there is no guarantee that any correlation found in the latter will hold in the former. If found, the result brings metallic glasses closer to the much wider cl…
Amorphous silica deforms viscoplastically at elevated temperatures, as is common for brittle glasses. The key mechanism of viscoplastic deformation involves interatomic bond switching, which is known to be a thermally activated process. In this study, through systematic in-situ compression tests by scanning electron microscopy, the viscoplastic deformation of amorphous silica is observed without thermal activation. Furthermore, ductility does not increase monotonically with acceleration voltage and current density of the SEM e-beam but is maximized by a factor of three at a specific accelerati…
An empirical potential that has been widely used to perform molecular dynamics studies on the fracture behavior of FeP metallic glasses is shown to exhibit spinodal decomposition in the composition range commonly studied. The phosphorous segregation induces a transition from ductility to brittleness. During brittle fracture the atomically sharp crack tip propagates along a percolating path with higher P concentration. This embrittlement is observed to occur over a wide range of chemical compositions, and toughness decreases linearly with the degree of compositional segregation over the entire …
Ductility and Brittle Fracture of Tungsten by Disconnection Pile-up on Twin Boundaries
Lawrence Livermore National Laboratory（劳伦斯利弗莫尔国家实验室）；Los Alamos National Laboratory（洛斯阿拉莫斯国家实验室）；University of California Irvine（加州大学尔湾分校）；University of California Los Angeles（加州大学洛杉矶分校）；Lehigh University（理海大学）；Northwestern University（西北大学）
We numerically study yielding in two-dimensional glasses which are generated with a very wide range of stabilities by swap Monte-Carlo simulations and then slowly deformed at zero temperature. We provide strong numerical evidence that stable glasses yield via a nonequilibrium discontinuous transition in the thermodynamic limit. A critical point separates this brittle yielding from the ductile one observed in less stable glasses. We find that two-dimensional glasses yield similarly to their three-dimensional counterparts but display larger sample-to-sample disorder-induced fluctuations, stronge…
We report in situ Atomic Force Microscopy experiments which reveal the presence of nanoscale damage cavities ahead of a stress-corrosion crack tip in glass. Their presence might explain the departure from linear elasticity observed in the vicinity of a crack tip in glass. Such a ductile fracture mechanism, widely observed in the case of metallic materials at the micrometer scale, might be also at the origin of the striking similarity of the morphologies of fracture surfaces of glass and metallic alloys at different length scales.
We report atomistic simulation results which indicate that the location of shear banding in a metallic glass (MG) can be ascertained with reasonably high accuracy solely from the undeformed static structure. Correlation is observed between the location of the initiation of shear bands in a simulated MG and the initial distribution of the density of fertile sites (DFS) for stress-driven shear transformations identified a priori based on a deep learning model devised in our recent work [Fan and Ma, Nat. Commun. 12, 1506 (2021)]. In addition, we demonstrated that one can judge whether a glass is …
The influence of thermal processing on the potential energy, atomic structure, and mechanical properties of metallic glasses is examined using molecular dynamics simulations. We study the three-dimensional binary mixture, which was first relaxed near the glass transition temperature, and then rapidly cooled deep into the glass phase. It was found that glasses prepared at higher annealing temperatures are relocated to higher energy states and their average glass structure remains more disordered, as reflected in the shape of the pair correlation function. The results of mechanical testing demon…
Hybrid glasses connect emerging fields of metal-organic frameworks (MOFs) with the glass-formation, amorphization, and melting processes of these structurally diverse and chemically versatile systems. Most zeolites, including MOFs, amorphize around the glass transition, devitrifying and then melting at much higher temperatures. The relationship between the two processes has so far not been investigated. Herein we show how heating first results in a low density perfect glass, following an order-order transition, leading to a super-strong liquid of low fragility that dynamically controls MOF col…
