We consider minimum mean square error (MMSE) joint precoder and combiner design for single and multi carrier distributed beamforming systems with nonuniform per-antenna transmit power constraints. We show that, similar to the maximum-gain problem, an iterative Gauss-Seidel algorithm can be used for minimizing MSE which alternately optimizes the transmitter and receiver coefficients. In a single carrier system the optimum transmit coefficients are obtained by a simple projection of the effective MISO channel. In the multicarrier case with a sum-MSE objective, the Gauss-Seidel approach is once again applicable, but the transmit coefficients must be found by solving a quadratically constrained quadratic problem for which we apply a dual gradient algorithm. A numerical example is presented which shows improvement of 0.7 dB in carrier signal-to-noise ratio (SNR) relative to a projected eigenvector method for a multicarrier DBF system with Rayleigh-faded multipath channels.
In this letter, we aim to design a robust hybrid precoder and combiner against beam misalignment in millimeter-wave (mmWave) communication systems. We consider the inclusion of the `error statistics' into the precoder and combiner design, where the array response that incorporates the distribution of the misalignment error is first derived. An iterative algorithm is then proposed to design the robust hybrid precoder and combiner to maximize the array gain in the presence of beam misalignment. To further enhance the spectral efficiency, a second-stage digital precoder and combiner are included …
We propose four hybrid combiner/precoder for downlink mmWave massive MU-MIMO systems. The design of a hybrid combiner/precoder is divided in two parts, analog and digital. The system baseband model shows that the signal processed by the mobile station can be interpreted as a received signal in the presence of colored Gaussian noise, therefore, since the digital part of the combiner and precoder do not have constraints for their generation, their designs can be based on any traditional signal processing that takes into account this kind of noise. To the best of our knowledge, this was not consi…
In this paper, we aim to design highly energy efficient end-to-end communication for millimeter wave multiple-input multiple-output systems. This is done by jointly optimizing the digital-to-analog converter (DAC)/analog-to-digital converter (ADC) bit resolutions and hybrid beamforming matrices. The novel decomposition of the hybrid precoder and the hybrid combiner to three parts is introduced at the transmitter (TX) and the receiver (RX), respectively, representing the analog precoder/combiner matrix, the DAC/ADC bit resolution matrix and the baseband precoder/combiner matrix. The unknown mat…
Configuring hybrid precoders and combiners is a major challenge to deploy practical mmWave communication systems. Prior work addresses the problem of designing hybrid precoders and combiner, yet focusing on finding solutions under a total transmit power constraint. The design of hybrid precoders and combiners in practical system, is constrained, however, by a per antenna transmit power, since each antenna element in the array is connected to a power amplifier (PA) that has to operate within its linear region. In this paper, we focus on the problem of hybrid precoding and combining with per-ant…
Hybrid beamforming has evolved as a promising technology that offers the balance between system performance and design complexity in mmWave MIMO systems. Existing hybrid beamforming methods either impose unit-modulus constraints or a codebook constraint on the analog precoders/combiners, which in turn results in a performance-overhead tradeoff. This paper puts forth a tensor framework to handle the wideband hybrid beamforming problem, with Vandermonde constraints on the analog precoders/combiners. The proposed method strikes the balance between performance, overhead and complexity. Numerical r…
Hybrid analog-digital precoding is challenging for broadband millimeter-wave (mmWave) massive MIMO systems, since the analog precoder is frequency-flat but the mmWave channels are frequency-selective. In this paper, we propose a principal component analysis (PCA)-based broadband hybrid precoder/combiner design, where both the fully-connected array and partially-connected subarray (including the fixed and adaptive subarrays) are investigated. Specifically, we first design the hybrid precoder/combiner for fully-connected array and fixed subarray based on PCA, whereby a low-dimensional frequency-…
This paper investigates the joint design of hybrid transmit precoder and analog receive combiners for single-group multicasting in millimeter-wave systems. We propose LB-GDM, a low-complexity learning-based approach that leverages gradient descent with momentum and alternating optimization to design (i) the digital and analog constituents of a hybrid transmitter and (ii) the analog combiners of each receiver. In addition, we also extend our proposed approach to design fully-digital precoders. We show through numerical evaluation that, implementing LB-GDM in either hybrid or digital precoders a…
By processing in the frequency domain (FD), massive MIMO systems can approach the theoretical per-user capacity using a single carrier modulation (SCM) waveform with a cyclic prefix. Minimum mean squared error (MMSE) detection and zero forcing (ZF) precoding have been shown to effectively cancel multi-user interference while compensating for inter-symbol interference. In this paper, we present a modified downlink precoding approach in the FD based on regularized zero forcing (RZF), which reuses the matrix inverses calculated as part of the FD MMSE uplink detection. By reusing these calculation…
In this paper, a downlink multiple input multiple output (MIMO) non-orthogonal multiple access (NOMA) wireless communication system is considered. In NOMA systems, the base station has unicast data for all users, and multiple users in a group share the same resources. The objective is to design transmit precoders and power allocation coefficients jointly that provide max-min fairness (MMF) among the strongest users in each group, while maintaining minimum target rates for all the other users. The problem is solved via two main iterative approaches. The first method is based on semi-definite re…
In this paper, we consider the amplify-and-forward relay networks in mmWave systems and propose a hybrid precoder/combiner design approach. The phase-only RF precoding/combining matrices are first designed to support multi-stream transmission, where we compensate the phase for the eigenmodes of the channel. Then, the baseband precoders/combiners are performed to achieve the maximum mutual information. Based on the data processing inequality for the mutual information, we first jointly design the baseband source and relay nodes to maximize the mutual information before the destination baseband …
Multicast beamforming is known to improve spectral efficiency. However, its benefits and challenges for hybrid precoders design in millimeter-wave (mmWave) systems remain understudied. To this end, this paper investigates the first joint design of hybrid transmit precoders (with an arbitrary number of finite-resolution phase shifts) and receive combiners for mmWave multi-group multicasting. Our proposed design leverages semidefinite relaxation (SDR), alternating optimization and Cholesky matrix factorization to sequentially optimize the digital/analog precoders at the transmitter and the combi…
Hybrid precoders and combiners are designed for cooperative cell-free multi-user millimeter wave (mmWave) multiple-input multiple-output (MIMO) cellular networks for low complexity interference mitigation. Initially, we derive an optimal hybrid transmit beamformer (HTBF) for a broadcast scenario considering both total and per access point (AP) power constraints. Next, an optimal successive hybrid beamformer technique is proposed for unicast and multicast scenarios which relies on the optimal minimum variance distortionless response (MVDR). We demonstrate that it mitigates both the interuser an…
We consider the vector perturbation (VP) precoder design for multiuser multiple-input single output (MU-MISO) broadcast channel systems which is robust to power scaling factor errors. VP precoding has so far been developed and analyzed under the assumption that receivers could have known the power scaling factor in advance of tranmission perfectly, which is hard to obtain due to the large dynamic range and limited feedforward. However, as demonstrated in our results the performance of VP precoding is quite sensitive to the accuracy of power scaling factor and always encounter an error floor at…
In this paper, we derive a closed-form expression for the combiner of a multiple-input-multiple-output (MIMO) receiver equipped with a minimum-mean-square-error (MMSE) estimator. We propose using variable-bit-resolution analog-to- digital converters (ADC) across radio frequency (RF) paths. The combiner designed is a function of the quantization errors across each RF path. Using very low bit resolution ADCs (1-2bits) is a popular approach with massive MIMO receiver architectures to mitigate large power demands. We show that for certain channel conditions, adopting unequal bit resolution ADCs (e…
We present distributed methods for jointly optimizing Intelligent Reflecting Surface (IRS) phase-shifts and beamformers in a cellular network. The proposed schemes require knowledge of only the intra-cell training sequences and corresponding received signals without explicit channel estimation. Instead, an SINR objective is estimated via sample means and maximized directly. This automatically includes and mitigates both intra- and inter-cell interference provided that the uplink training is synchronized across cells. Different schemes are considered that limit the set of known training sequenc…
This paper proposes a reconfigurable intelligent surface (RIS)-aided and angular-based hybrid beamforming (AB-HBF) technique for the millimeter wave (mmWave) massive multiple-input multiple-output (MIMO) systems. The proposed RIS-AB-HBF architecture consists of three stages: (i) RF beamformer, (ii) baseband (BB) precoder/combiner, and (iii) RIS phase shift design. First, in order to reduce the number of RF chains and the channel estimation overhead, RF beamformers are designed based on the 3D geometry-based mmWave channel model using slow time-varying angular parameters of the channel. Second,…
Precoding design exploiting deep learning methods has been widely studied for multiuser multiple-input multiple-output (MU-MIMO) systems. However, conventional neural precoding design applies black-box-based neural networks which are less interpretable. In this paper, we propose a deep learning-based precoding method based on an interpretable design of a neural precoding network, namely iPNet. In particular, the iPNet mimics the classic minimum mean-squared error (MMSE) precoding and approximates the matrix inversion in the design of the neural network architecture. Specifically, the proposed …
We derive an expression for the capacity of massive multiple-input multiple-output Millimeter wave (mmWave) channel where the receiver is equipped with a variable-resolution Analog to Digital Converter (ADC) and a hybrid combiner. The capacity is shown to be a function of Cramer-Rao Lower Bound (CRLB) for a given bit-allocation matrix and hybrid combiner. The condition for optimal ADC bit-allocation under a receiver power constraint is derived. This is derived based on the maximization of capacity with respect to bit-allocation matrix for a given channel, hybrid precoder, and hybrid combiner. …
Linear hybrid beamformer designs are conceived for the decentralized estimation of a vector parameter in a millimeter wave (mmWave) multiple-input multiple-output (MIMO) Internet of Things network (IoTNe). The proposed designs incorporate both total IoTNe and individual IoTNo power constraints, while also eliminating the need for a baseband receiver combiner at the fusion center (FC). To circumvent the non-convexity of the hybrid beamformer design problem, the proposed approach initially determines the minimum mean square error (MMSE) digital transmit precoder (TPC) weights followed by a simul…
Department of Electrical Engineering, National Tsing Hua University（国立清华大学电机工程学系）；Research Center for Information Technology Innovation, Academia Sinica（中央研究院资讯科技创新研究中心）
Millimeter wave (mmWave) is a key technology for fifth-generation (5G) and beyond communications. Hybrid beamforming has been proposed for large-scale antenna systems in mmWave communications. Existing hybrid beamforming designs based on infinite-resolution phase shifters (PSs) are impractical due to hardware cost and power consumption. In this paper, we propose an unsupervised-learning-based scheme to jointly design the analog precoder and combiner with low-resolution PSs for multiuser multiple-input multiple-output (MU-MIMO) systems. We transform the analog precoder and combiner design probl…
Intelligent reflecting surface (IRS) has emerged as a promising solution to enhance wireless information transmissions by adaptively controlling prorogation environment. Recently, the brand-new concept of utilizing IRS to implement a passive transmitter attracts researchers' attention since it potentially realizes low-complexity and hardware-efficient transmitters of multiple-input single/multiple-output (MISO/MIMO) systems. In this paper we investigate the problem of precoder design for a low-resolution IRS-based transmitter to implement multi-user MISO/MIMO wireless communications. Particula…
Millimeter wave (mmWave) is a practical solution to provide high data rate for the vehicle-to-everything (V2X) communications. This enables the future autonomous vehicles to exchange big data with the base stations (BSs) such as the velocity and the location to improve the awareness of the advanced driving assistance system (ADAS). In this context, we consider a single-cell multiuser doubly-selective system wherein the BS simultaneously serves multiple vehicles. To accomplish this requirement, the BS is implemented in hybrid architecture to support multiple spatial streams while the vehicles h…
In this work, we present a solution for coordinated beamforming and power allocation when base stations employ a massive number of antennas equipped with low-resolution analog-to-digital and digital-to-analog converters. We address total power minimization problems of the coarsely quantized uplink (UL) and downlink (DL) communication systems with target signal-to-interference-plus-noise ratio (SINR) constraints. By combining the UL problem with minimum mean square error combiners and deriving the Lagrangian dual of the DL problem, we prove UL-DL duality and show there is no duality gap even wi…
In this paper, we study the channel estimation problem in correlated massive multiple-input-multiple-output (MIMO) systems with a reduced number of radio-frequency (RF) chains. Importantly, other than the knowledge of channel correlation matrices, we make no assumption as to the structure of the channel. To address the limitation in the number of RF chains, we employ hybrid beamforming, comprising a low dimensional digital beamformer followed by an analog beamformer implemented using phase shifters. Since there is no dedicated RF chain per transmitter/receiver antenna, the conventional channel…
Recently, full duplex (FD) has been studied in 5G LTE millimeter wave (mmWave) cellular communications for New Radio in 3GPP releases 15-17. FD allows bidirectional transmission over the same resources and has the potential to reduce latency and double spectral efficiency. Self-interference (SI) is the primary drawback. SI can be several orders of magnitude greater than the received signal power, saturate the analog-to-digital converters (ADCs) and degrade communication performance severely. Massive mmWave antenna arrays may provide enough degrees of freedom for spatial multiplexing and SI sup…
Owing to the unique advantages of low cost and controllability, reconfigurable intelligent surface (RIS) is a promising candidate to address the blockage issue in millimeter wave (mmWave) communication systems, consequently has captured widespread attention in recent years. However, the joint active beamforming and passive beamforming design is an arduous task due to the high computational complexity and the dynamic changes of wireless environment. In this paper, we consider a RIS-assisted multi-user multiple-input single-output (MU-MISO) mmWave system and aim to develop a deep reinforcement l…
TU Braunschweig（布伦瑞克工业大学）；Beijing Jiaotong University（北京交通大学）；Beijing University of Posts and Telecommunications（北京邮电大学）
Reconfigurable intelligent surface (RIS) is an emerging technology for future wireless communication systems. In this work, we consider downlink spatial multiplexing enabled by the RIS for weighted sum-rate (WSR) maximization. In the literature, most solutions use alternating gradient-based optimization, which has moderate performance, high complexity, and limited scalability. We propose to apply a fully convolutional network (FCN) to solve this problem, which was originally designed for semantic segmentation of images. The rectangular shape of the RIS and the spatial correlation of channels w…
This paper investigates dual-layer non-orthogonally superimposed transmissions for industrial internet of things (IoT) millimeter-wave communications. Essentially, the overlayer is a ubiquitous multicast signal devised to serve all the devices in coverage with a common message, i.e., critical control packet. The underlayer is a composite signal that consists of private unicast messages. Due to safety implications, it is critical that all devices can decode the multicast information. To ensure this requirement, we jointly optimize the hybrid precoder, analog combiners, power allocation, and fai…
In multiple antenna systems employing time-division duplexing, spatial precoder design at the base station (BS) leverages channel state information acquired through uplink pilot transmission, under the assumption of channel reciprocity. Malicious eavesdroppers can start pilot spoofing attacks to alter such design, so as to improve their eavesdropping performance in downlink. The aim of this paper is to study the effects of pilot spoofing attacks on uplink channel estimation, by assuming that the BS knows the angle of arrivals (AoAs) of the legitimate channels. Specifically, after assessing the…
We consider multi-group multicast precoding designs for cell-free massive multiple-input multiple-output (MIMO) systems. To optimize the transmit and receive beamforming strategies, we focus on minimizing the sum of the maximum mean squared errors (MSEs) over the multicast groups, which is then approximated with the sum MSE to simplify the computation and signaling. We adopt an iterative bi-directional training scheme with uplink and downlink precoded pilots to cooperatively design the multi-group multicast precoders at each base station and the combiners at each user equipment in a distribute…
Hybrid beamformer design plays very crucial role in the next generation millimeter-wave (mm-Wave) massive MIMO (multiple-input multiple-output) systems. Previous works assume the perfect channel state information (CSI) which results heavy feedback overhead. To lower complexity, channel statistics can be utilized such that only infrequent update of the channel information is needed. To reduce the complexity and provide robustness, in this work, we propose a deep learning (DL) framework to deal with both hybrid beamforming and channel estimation. For this purpose, we introduce three deep convolu…
In this paper, we investigate a coordinated multipoint (CoMP) beamforming and power control problem for base stations (BSs) with a massive number of antenna arrays under coarse quantization at low-resolution analog-to-digital converters (ADCs) and digital-to-analog converter (DACs). Unlike high-resolution ADC and DAC systems, non-negligible quantization noise that needs to be considered in CoMP design makes the problem more challenging. We first formulate total power minimization problems of both uplink (UL) and downlink (DL) systems subject to signal-to-interference-and-noise ratio (SINR) con…
Large intelligent surface (LIS) has recently emerged as a potential low-cost solution to reshape the wireless propagation environment for improving the spectral efficiency. In this paper, we consider a downlink millimeter-wave (mmWave) multiple-input-multiple-output (MIMO) system, where an LIS is deployed to assist the downlink data transmission from a base station (BS) to a user equipment (UE). Both the BS and the UE are equipped with a large number of antennas, and a hybrid analog/digital precoding/combining structure is used to reduce the hardware cost and energy consumption. We aim to maxi…
This paper deals with the problem of jointly designing the source precoder, the relaying matrices, and the destination equalizer in a multiple-relay amplify-and-forward (AF) cooperative multiple-input multiple-output (MIMO) wireless network, when partial channel-state information (CSI) is available. Specifically, the considered approaches are based on the knowledge of instantaneous CSI of the first-hop channel matrix, whereas only statistical CSI of the second-hop channels is assumed. In such a scenario, with respect to the case when instantaneous CSI of both the first- and second-hop MIMO cha…
