Controlled anisotropic growth of two-dimensional materials provides an approach for the synthesis of large single crystals and nanoribbons, which are promising for applications as low-dimensional semiconductors and in next-generation optoelectronic devices. In particular, the anisotropic growth of transition metal dichalcogenides induced by the substrate is of great interest due to its operability. To date, however, their substrate-induced anisotropic growth is typically driven by the optimization of experimental parameters without uncovering the fundamental mechanism. Here, the anisotropic growth of monolayer tungsten disulfide on an ST-X quartz substrate is achieved by chemical vapor deposition, and the mechanism of substrate-induced anisotropic growth is examined by kinetic Monte Carlo simulations. These results show that, besides the variation of substrate adsorption, the chalcogen to metal (C/M) ratio is a major contributor to the large growth anisotropy and the polarization of undergrowth and overgrowth; either perfect isotropy or high anisotropy can be expected when the C/M ratio equals 2.0 by properly controlling the linear relationship between gas flux and temperature.
Monolayer materials are strongly affected by their potential fluctuations, which are induced by an intrinsic corrugation or the surface roughness of the substrate. We compare the effective exciton-exciton annihilation (EEA) rate constants of monolayer WS2 on substrates with different surface topographies. We show that monolayer WS2 on the substrate with atomically flat terraces displays small effective EEA rate constant deviating from the overall tendency and multiple exciton decay components, which cannot be accounted for by a conventional EEA model. To obtain a correct description, we use a …
Intrinsic electrical and excitonic properties of monolayer transition metal dichalcogenides are studied on CYTOP fluoropolymer substrates with greatly suppressed unintentional doping and dielectric screening. Ambipolar transport behavior is observed in monolayer WS2 by applying solid states backdates. The excitonic properties of monolayer MoS2 and WS2 are determined by intricate interplays between the bandage renormalization, Pauli blocking and carrier screening against carrier doping.
Auger Electron Spectroscopy, Low Energy Electron Diffraction and Scanning Tunneling Microscopy have been used to study the atomic structure of a Zn monolayer deposited on Ag(111) and Ag(110) substrates at room temperature. On both faces, there is formation of a close packed monolayer of Zn covering the entire substrate surface and giving rise to specific Moir{é} patterns. From a comprehensive LEED and STM data analysis, we deduce that the Zn monolayer adopts a (111) structure equivalent to a pure Zn layer rotated with respect to the silver substrate, of about $1.5^\circ$ on the Ag(111) face an…
Recent experiments have found that monolayer 1H-TaS2 grown on Au(111) lacks the charge density wave (CDW) instability exhibited by bulk 2H-TaS2. Additionally, angle-resolved photoemission spectroscopy measurements suggest that the monolayer becomes strongly electron doped by the substrate. While density functional theory (DFT) calculations have shown that electron doping can suppress the CDW instability in monolayer 1H-TaS2, it has been suggested that the actual charge transfer from the substrate may be much smaller than the apparent doping deduced from photoemission data. We present DFT calcu…
The substrate contribution to the magnetic anisotropy energy (MAE) of supported nanostructures can be quantified by a site-selective manipulation of the spin-orbit coupling (SOC) and the effective exchange field B_ex. A systematic study of Co adatoms and Co monolayers on the (111) surfaces of Cu, Ag, Au, Pd and Pt is performed to study common trends in this class of materials. It is found that for adatoms, the substrate contribution is relatively small (10-30% of the MAE) while for monolayers, the substrate contribution can be substantial. The contribution from the SOC is much more important t…
Electronic structure of S-C6H5 self-assembled monolayers on Cu(111) and Au(111) substrates
采用第一性原理密度泛函理论计算了苯硫醇（S-C $_6$ H $_5$）在Cu（111）和Au（111）衬底上的自组装单分子层（SAM）的电子结构.我们发现了SAM分子态的显着横向分散，并讨论了其对分子线阵列输运性质的影响。计算了Cu（111）表面自组装膜的双光子光电子能谱和功函数，并与已有的实验数据进行了比较。我们的研究结果被用来讨论所观察到的光谱数据的分配和产量预测新的电子状态，由于单层尚未访问实验。
We report on large exciton tuning in WSe$_2$ monolayers via substrate induced non-degenerate doping. We observe a redshift of $\sim$62 meV for the $A$ exciton together with a 1-2 orders of magnitude photoluminescence (PL) quenching when the monolayer WSe$_2$ is brought in contact with highly oriented pyrolytic graphite (HOPG) compared to the dielectric substrates such as hBN and SiO$_2$. As the evidence of doping from HOPG to WSe$_2$, a drastic increase of the trion emission intensity was observed. Using a systematic PL and Kelvin probe force microscopy (KPFM) investigation on WSe$_2$/HOPG, WS…
The transfer-free synthesis of high-quality, large-area graphene on a given dielectric substrate, which is highly desirable for device applications, remains a significant challenge. In this paper, we report on a simple rapid thermal treatment method for the fast and direct growth of high-quality, large-scale monolayer graphene on a SiO2/Si substrate from solid carbon sources. The stack structure of solid carbon layer/copper film/SiO2 is adopted in the RTT process. The inserted copper film does not only act as an active catalyst for the carbon precursor but also serves as a "filter" that preven…
The thermal properties of two-dimensional (2D) materials, like MoS$_2$, are known to be affected by interactions with their environment, but this has primarily been studied only with SiO$_2$ substrates. Here, we compare the thermal conductivity (TC) and thermal boundary conductance (TBC) of monolayer MoS$_2$ on amorphous (a-) and crystalline (c-) SiO$_2$, AlN, Al$_2$O$_3$, and $\textit{h}$-BN monolayers using molecular dynamics. The room temperature TC of MoS$_2$ is ~38 Wm$^{-1}$K$^{-1}$ on amorphous substrates and up to ~68 Wm$^{-1}$K$^{-1}$ on crystalline substrates, with most of the differe…
We perform in-situ two-cycle thermal cycling and annealing studies for a transferred CVD-grown monolayer MoS2 on a SiO2/Si substrate, using spatially resolved micro-Raman and PL spectroscopy. After the thermal cycling and being annealed at 305 deg C twice, the film morphology and film-substrate bonding are significantly modified, which together with the removal of polymer residues cause major changes in the strain and doping distribution over the film, and thus the optical properties. Before annealing, the strain associated with ripples in the transferred film dominates the spatial distributio…
Although many possible two-dimensional (2D) topological insulators (TIs) have been predicted in recent years, there is still lack of experimentally realizable 2D TI. Through first-principles and tight-binding simulations, we found an effective way to stabilize the robust quantum spin Hall state with a large nontrivial gap of 227 meV in 2D honeycomb HgTe monolayer by the Al$_2$O$_3$(0001) substrate. The band topology originates from the band inversion between the $s-$like and $p-$like orbitals that are contributed completely by the Hg and Te atoms, so the quantized edge states are restricted wi…
The unique thinness of two-dimensional materials enables control over chemical phenomena at their surfaces by means of various gating techniques. For example, gating methods based on field-effect-transistor configurations have been achieved. Here, we report a molecular gating approach that employs a local electric field generated by a polar self-assembled monolayer formed on a supporting substrate. By performing Raman scattering spectroscopy analyses with a proper data correction procedure, we found that molecular gating is effective for controlling solid phase photochemical reactions of graph…
In most envisioned applications, full utilization of a graphene-carbon nanotube (CNT) construct requires maintaining the integrity of the graphene layer during the CNT growth step. In this work, we exhibit an approach towards controlled CNT growth atop graphene substrates where the reaction equilibrium between source hydrocarbon decomposition and carbon saturation into and precipitation from the catalyst nanoparticles shifts towards CNT growth rather than graphene consumption. By utilizing C2H4 feedstock, we demonstrate that the low temperature growth permissible with this gas suppresses undes…
The advantage of MoS2, compared with graphene, is the direct growth on various oxide substrates by chemical vapor deposition (CVD) without utilizing catalytic metal substrates, which facilitates practical applications for electronics. The carrier mobility is, however, degraded from the intrinsic limit mainly due to short-range scattering caused by S vacancies formed during CVD growth. If the upper limit for the crystallinity of CVD-MoS2 on oxide substrates is determined by the MoS2/substrate interaction during growth, it will hinder the advantage. In this study, we investigated the interaction…
Lifting the valley degeneracy is an efficient way to achieve valley polarization for further valleytronics operations. In this work, we demonstrate that a large valley splitting can be obtained in monolayer transition metal dichalcogenides by magnetic proximity coupling to an insulating antiferromagnetic substrate. As an example, we perform first-principles calculations to investigate the electronic structures of monolayer WS$_2$ on the MnO(111) surface. Our calculation results suggest that a large valley splitting of 214 meV, which corresponds to a Zeeman magnetic field of 1516 T, is induced …
We have investigated the influence of the substrate on the fluorescence of adsorbed organic molecules. Monolayer films of perylene-3,4,9,10-tetracarboxylic-3,4,9,10-diimide (PTCDI), a supramolecular network formed from PTCDI and melamine, and perylene-3,4,9,10-tetracarboxylic-3,4,9,10-dianhydride (PTCDA) have been deposited on hexagonal boron nitride (hBN). The principal peaks in the fluorescence spectra of these films were red-shifted by up to 0.37 eV relative to published measurements for molecules in helium droplets. Smaller shifts (~0.03 eV) arising from interactions between neighbouring m…
Sub-monolayer physical layer deposition of Zn on Ag(111) substrate at room temperature is investigated using Auger electron spectroscopy, low energy electron diffraction and scanning tunneling microscopy. We identified an original Zn highly-anisotropic structure in the shape of finger-like inserted dendrite in front of Zn monolayer growth. On the basis of STM observations, a mechanism of inserted dendritic growth and a mechanism of its transition to layered growth are proposed.
The study of the adsorption phenomenon of helium began many decades ago with the discovery of graphite as a homogeneous substrate for investigation of physically adsorbed monolayer films. In particular, helium monoatomic layers on graphite were found to exhibit a very rich phase diagram. In the present work we have investigated the adsorption phenomenon of helium atoms on graphene and silicene substrates by means of density functional theory with Born-Oppenheimer approximation. Helium-substrate and helium-helium interactions were considered from first principles. Vibrational properties of adso…
Monolayer transition metal dichalcogenides (TMDCs) are direct gap semiconductors with unique potential for ultrathin light emitters. Yet, their photoluminescence (PL) is not completely understood. We compute the radiative recombination rate in monolayer TMDCs as a function of photon emission direction and polarization, and obtain polar plots of the PL for different excitation scenarios using the ab initio Bethe-Salpeter equation. We show that excitons in a quantum superposition state of the K and K' inequivalent valleys emit light anisotropically upon recombination. Our results can explain the…
Graphene monolayers supported on oxide substrates have been demonstrated with superior charge mobility and thermal transport for potential device applications. Morphological corrugation can strongly influence the transport properties of the supported graphene. In this paper, we theoretically analyze the morphological stability of a graphene monolayer on an oxide substrate, subject to van der Waals interactions and in-plane mismatch strains. First, we define the equilibrium separation and the interfacial adhesion energy as the two key parameters that characterize the van der Waals interaction b…
Beryllium polynitrides, BeN4 is a novel layered material, which has been most recently fabricated under high pressure (Phys. Rev. Lett. 126(2021), 175501). As a new class of 2D materials, in this work we conduct first-principles calculations to examine the stability and explore the electronic nature of MN4 (M= Be, Mg, Ir, Rh, Ni, Cu, Au, Pd, Pt) monolayers. Acquired results confirm the dynamical and thermal stability of BeN4, MgN4, IrN4, PtN4 and RhN4 monolayers. Interestingly, BeN4 and MgN4 monolayers are found to show anisotropic Dirac cones in their electronic structure. While PtN4 monolaye…
We present detailed ab initio study of structural and magnetic stability of a Fe-monolayer on the fcc(001) surface of iridium. The Fe-monolayer has a strong tendency to order antiferromagnetically for the true relaxed geometry. On the contrary an unrelaxed Fe/Ir(001) sample has a ferromagnetic ground state. The antiferromagnetism is thus stabilized by the decreased Fe-Ir layer spacing in striking contrast to the recently experimentally observed antiferromagnetism of the Fe/W(001) system which exists also for an ideal bulk-truncated, unrelaxed geometry. The calculated layer relaxations for Fe/I…
Ab-initio density functional theory calculations are performed to study the electronic properties of a MoS2 monolayer deposited over a SiO2 substrate in the presence of interface impurities and defects. When MoS2 is placed on a defect-free substrate the oxide plays an insignificant role, since the conduction band top and the valence band minimum of MoS2 are located approximately in the middle of the SiO2 band-gap. However, if Na impurities and O dangling bonds are introduced at the SiO2 surface, these lead to localized states, which modulate the conductivity of the MoS2 monolayer from n- to p-…
Two-dimensional (2D) ferromagnetic materials have been exhibiting promising potential in applications, such as spintronics devices. To grow epitaxial magnetic films on silicon substrate, in the single-layer limit, is practically important but challenging. In this study, we realized the epitaxial growth of MnSn monolayer on Si(111) substrate, with an atomically thin Sn/Si(111)-$2\sqrt{3}\times2\sqrt{3}$- buffer layer, and controlled the MnSn thickness with atomic-layer precision. We discovered the ferromagnetism in MnSn monolayer with the Curie temperature (Tc) of ~54 K. As the MnSn film is gro…
Precise and scalable defect engineering of 2D nanomaterials is acutely sought-after in contemporary materials science. Here we present defect engineering in monolayer graphene and molybdenum disulfide (MoS$_2$) by irradiation with noble gas ions at 30 keV. Two ion species of different masses were used in a gas field ion source microscope: helium (He$^+$) and neon (Ne$^+$). A detailed study of the introduced defect sizes and resulting inter-defect distance with escalating ion dose was performed using Raman spectroscopy. Expanding on existing models, we found that the average defect size is cons…
We have carried out first-principles based DFT calculation on electronic properties of silicene monolayer on various (111) semi-conducting surfaces. We find that the relative stability and other properties of the silicene overlayer depends sensitively on whether the interacting top layer of the substrate is metal or non-metal terminated. The nature of silicene-monolayer on the metal termi- nated surface can be metallic or even magnetic, depending upon the choice of the substrate. The silicene overlayer undergoes n-type doping on metal terminated surface while it undergoes p-type doping on non …
We propose a guideline for exploring substrates that stabilize the monolayer honeycomb structure of silicene and germanene while simultaneously preserve the Dirac states: in addition to have a strong binding energy to the monolayer, a suitable substrate should be a large-gap semiconductor with a proper workfunction such that the Dirac point lies in the gap and far from the substrate states when their bands align. We illustrate our idea by performing first-principles calculations for silicene and germanene on the Al-terminated (0001) surface of Al2O3 . The overlaid monolayers on Al-terminated A…
We analyze the occurrence of in-plane anisotropy in the electronic, magnetic, elastic and transport properties of more than one thousand 2D materials from the C2DB database. We identify hundreds of anisotropic materials and classify them according to their point group symmetry and degree of anisotropy. A statistical analysis reveals that a lower point group symmetry and a larger amount of different elements in the structure favour all types of anisotropies, which could be relevant for future materials design approaches. Besides, we identify novel compounds, predicted to be easily exfoliable fr…
Epitaxial growth of graphene on transition metal substrates is an important route for obtaining large scale graphene. However, the interaction between graphene and the substrate often leads to multiple orientations, distorted graphene band structure, large doping and strong electron-phonon coupling. Here we report the growth of monolayer graphene with high crystalline quality on Pt(111) substrate by using a very low concentration of an internal carbon source with high annealing temperature. The controlled growth leads to electronically decoupled graphene: it is nearly charge neutral and has ex…
The sensitive dependence of monolayer materials on their environment often gives rise to unexpected properties. It was recently demonstrated that monolayer FeSe on a SrTiO$_3$ substrate exhibits a much higher superconducting critical temperature T$_C$ than the bulk material. Here, we examine the interfacial structure of FeSe / SrTiO$_3$ and the effect of an interfacial Ti$_{1+x}$O$_2$ layer on the increased T$_C$ using a combination of scanning transmission electron microscopy and density functional theory. We find Ti$_{1+x}$O$_2$ forms its own quasi-two-dimensional layer, bonding to both the …
Anisotropy is a general feature in materials. Strong anisotropy could lead to interesting physical properties and useful applications. Here, based on first-principles calculations and theoretical analysis, we predict a stable two-dimensional (2D) material---the monolayer MoOCl$_2$, and show that it possesses intriguing properties related to its high anisotropy. Monolayer MoOCl$_2$ can be readily exfoliated from the van der Waals layered bulk, which has already been synthesized. We show that a high in-plane anisotropy manifests in the structural, phononic, mechanical, electronic, and optical pr…
The application of graphene in electronic devices requires large scale epitaxial growth. The presence of the substrate, however, usually reduces the charge carrier mobility considerably. We show that it is possible to decouple the partially sp3-hybridized first graphitic layer formed on the Si-terminated face of silicon carbide from the substrate by gold intercalation, leading to a completely sp2-hybridized graphene layer with improved electronic properties.
Photoluminescence (PL) of transition metal dichalcogenide (TMD) monolayers is strongly influenced by the dielectric environment. The defect states present in the substrate induces uncontrollable doping in the TMD monolayer and thereby modifies the PL spectra. There have been enormous efforts to tune and overcome the effect of inevitable subtract defects in PL spectra, but a proper understanding and a convenient way are still lacking. Here, we systematically studied the effect of surface defects by gradually increasing the separation between WS2 monolayer and substrate. Hence, we could precisel…
Structural, electronic, ferroelectric, and optical properties of two-dimensional (2D) BiN monolayer material with phosphorene-like structure are studied in terms of the density functional theory and modern Berry phase ferroelectric method. Both phonon spectra and molecular dynamics simulations indicate that the BiN monolayer is a room-temperature stable 2D ferroelectric with polarization as large as 580 pC/m. Further studies show that the polarization in the BiN monolayer can be easily switched from [100] to [010] direction over the bridging saddle phase by applying a tensile [010] stress of 2…
The geometric and electronic properties of Bi-adsorbed monolayer graphene, enriched by the strong effect of substrate, are investigated by first-principles calculations. The six-layered substrate, corrugated buffer layer, and slightly deformed monolayer graphene are all simulated. Adatom arrangements are thoroughly studied by analyzing the ground-state energies, bismuth adsorption energies, and Bi-Bi interaction energies of different adatom heights, inter-adatom distance, adsorption sites, and hexagonal positions. A hexagonal array of Bi atoms is dominated by the interactions between the buffe…
Here, we have identified the monolayer phase of Bi2O2Se as a promising two-dimensional semiconductor with ultra-high carrier mobility and giant electric polarization. Due to the strong reconstruction originated from the interlayer electrostatic force, we have applied structure prediction algorithms to explore the crystalline geometry of Bi2O2Se monolayer with the lowest total energy. Considering Se and Te belong to the same group, Bi2O2Te monolayer is also investigated based on a similar scheme. Further calculations suggest that the high carrier mobility is maintained in the monolayer phase an…
Considering the rapid development of experimental techniques for fabricating 2D materials in recent years, various monolayers are expected to be experimentally realized in the near future. Motivated by the recent research activities focused on the honeycomb arsenene monolayers, stability and carrier mobility of non-honeycomb and porous allotropic arsenene are determined using first principles calculations. In addition to five honeycomb structures of arsenene, a total of eight other structures are considered in this study. An extensive analysis comprising energetics, phonon spectra and mechanic…
Transition metal dichalcogenide (TMDC) monolayers present a remarkable multifunctional material with potential to enable the development of a wide range of novel devices. However, the functionalities observed often fall short of the expectation, which hinders the device development. Here we demonstrate that the optical, catalytic, and thermal functionalities of TMDC monolayers can all be substantially enhanced by up to orders of magnitude with the intercalation of water molecules or small cations (H+ and Li+) between the monolayers and underlying substrates. In contrast, the same molecules or …
We study theoretically and experimentally the infrared (IR) spectrum of an adamantane monolayer on a Au(111) surface. Using a new STM-based IR spectroscopy technique (IRSTM) we are able to measure both the nanoscale structure of an adamantane monolayer on Au(111) as well as its infrared spectrum, while DFT-based ab initio calculations allow us to interpret the microscopic vibrational dynamics revealed by our measurements. We find that the IR spectrum of an adamantane monolayer on Au(111) is substantially modified with respect to the gas-phase IR spectrum. The first modification is caused by th…
Iron-mediated on-surface synthesis of substrate-decoupled graphdiyne monolayers
Politecnico di Milano（米兰理工大学）；Università degli Studi di Milano（米兰大学）；INFN Sezione di Milano（意大利国家核物理研究所米兰分部）；Università Degli Studi Di Padova（帕多瓦大学）；Instituto de Nanociencia y Materiales de Aragon (INMA), CSIC-Universidad de Zaragoza（阿拉贡纳米科学与材料研究所（INMA），西班牙科学研究中心-萨拉戈萨大学）；Università di Pavia（帕维亚大学）；Friedrich-Alexander Universität Erlangen-Nürnberg（埃尔朗根-纽伦堡大学）
Low-dimensional ferroelectricity has attracted tremendous attention due to its huge potential in device applications. Here, based on first-principles calculations, we predict the existence of spontaneous in-plane electrical polarization and ferroelectricity in monolayer $β$-GeSe, a polymorph of GeSe with a boat conformation newly synthesized in experiment. The magnitude of the polarization is about $0.16$ nC/m, which is comparable to that of monolayer SnTe studied in recent experiment, and the intrinsic Curie temperature is estimated to be above 200 K. Interestingly, owing to its puckered stru…
Both the intrinsic anisotropic optical materials and fullerene-assembled 2D materials have attracted a lot of interests in fundamental science and potential applications. The synthesis of a monolayer (ML) fullerene makes the combination of these two features plausible. In this work, using first-principles calculations, we systematically study the electronic structure, optical properties of quasi-hexagonal phase (qHP) ML and quasi-tetragonal phase (qTP) ML fullerenes. The calculations of qHP ML show that it is a semi-conductor with small anisotropic optical absorption, which agrees with the rec…
Monolayers of transition-metal dichalcogenides such as WSe2 have become increasingly attractive due to their potential in electrical and optical applications. Because the properties of these 2D systems are known to be affected by their surroundings, we report how the choice of the substrate material affects the optical properties of monolayer WSe2. To accomplish this study, pump-density-dependent micro-photoluminescence measurements are performed with time-integrating and time-resolving acquisition techniques. Spectral information and power-dependent mode intensities are compared at 290K and 1…
Dzyaloshinskii-Moriya interaction (DMI) is the primary mechanism for realizing real-space chiral spin textures, which are regarded as key components for the next-generation spintronics. However, DMI arises from a perturbation term of the spin-orbit interaction and is usually weak in pristine magnetic semiconductors. To date, large DMI and the resulting skyrmions are only realized in a few materials under stringent conditions. Using first-principles calculations, we demonstrate that significant DMI occurs between nearest-neighbor Cr atoms in two-dimensional (2D) magnetic semiconductor CrI$_3$ o…
