We investigated electronic structure and magnetic anisotropy in the Fe/MgO interface of magnetic metal and dielectric insulator under the Cr layer of small electronegativity, by means of the first-principles density functional approach. The result indicates that the interface resonance state gets occupied unlike a typical rigid band picture as the number of Fe layers decreases, finding large perpendicular anisotropies in the oscillating behavior for thickness dependence. We discuss scenarios of the two dimensional van Hove singularity associated with flat band dispersions, and also the accuracies of anisotropy energy in comparison with the available experimental data.
Understanding the magnetic anisotropy at ferromagnetic metal/oxide interface is a fundamental and intriguing subject. Here we propose an approach to manipulate the strength of perpendicular magnetic anisotropy (PMA) by varying MgO thickness in the MgO/CoFeB/Ta thin films. We identify that the PMA at the MgO/CoFeB interface is tuned by the crystalline structure of bulk MgO layer and decreases dramatically due to the onset of crystalline MgO forming with the increase of MgO thickness. Our work opens an avenue to manipulate the magnetic anisotropy by the modification of the ferromagnetic metal/ox…
Epitaxial growth of Co20Fe50Ge30 thin film on single crystal MgO (001) substrate is reported. Structure characterization revealed (001)-oriented B2 order of CoFeGe well lattice matched with the MgO barrier. Perpendicular magnetic anisotropy (PMA) was achieved in the MgO/CoFeGe/MgO structure with an optimized magnetic anisotropy energy density (K) of 3 106 erg/cm3. The magnetic anisotropy is found to depend strongly on the thickness of the MgO and CoFeGe layers, indicating that the PMA of CoFeGe is contributed by the interfacial anisotropy between CoFeGe and MgO. With reported low damping const…
Broadband ferromagnetic resonance is measured in single crystalline Fe films of varying thickness sandwiched between MgO layers. An exhaustive magnetic characterization of the films (exchange constant, cubic, uniaxial and surface anisotropies) is enabled by the study of the uniform and the first perpendicular standing spin wave modes as a function of applied magnetic field and film thickness. Additional measurements of non-reciprocal spin wave propagation allow us to separate each of the two interface contributions to the total surface anisotropy. The results are consistent with the model of a…
We observe magnetic domain structures of MgO/CoFeB with a perpendicular magnetic easy axis under an electric field. The domain structure shows a maze pattern with electric-field dependent isotropic period. We find that the electric-field modulation of the period is explained by considering the electric-field modulation of the exchange stiffness constant in addition to the known magnetic anisotropy modulation.
The authors demonstrated that L21-ordered full-Heusler Co2FeSi (CFS) alloy film with thickness of 100 nm were formed by facing targets sputtering (FTS) method at a substrate temperature TS = 300 deg C. Degrees of L21- and B2- order for the film were 0.37, and 0.96, respectively. Furthermore, full-Heusler CFS alloy thin films with perpendicular magnetic anisotropy (PMA) induced by MgO-interface magnetic anisotropy were successfully formed by the FTS method. The CFS/MgO stacking layers showed PMA when dCFS was 0.6 nm <= dCFS <= 1.0 nm. The PMA in these structures resulted from the CFS/MgO interf…
Recently, perpendicular magnetic anisotropy (PMA) and its voltage control (VC) was demonstrated for Cr/Fe/MgO (Physical Review Applied 5, 044006 (2016)). In this study, we shed a light on the origin of large voltage-induced anisotropy change in Cr/Fe/MgO. Analysis of the chemical structure of Cr/Fe/MgO revealed the existence of Cr atoms in the proximity of the Fe/MgO interface, which can affect both magnetic anisotropy (MA) and its VC. We showed that PMA and its VC can be enhanced by controlled Cr doping at the Fe/MgO interface. For Cr/Fe (5.9 Å)/Cr (0.7 Å)/MgO with an effective PMA of 0.8 MJ/…
The structures of epitaxial ultrathin Co2FeAl/MgO(001) heterostructures relating to the interface-induced perpendicular magnetic anisotropy (PMA) were investigated using scanning transmission electron microscopy, energy dispersive x-ray spectroscopy, and x-ray magnetic circular dichroism. We found that Al atoms from the Co2FeAl layer significantly interdiffuse into MgO, forming an Al-deficient Co-Fe-Al/Mg-Al-O structure near the Co2FeAl/MgO interface. This atomic replacement may play an additional role for enhancing PMA, which is consistent with the observed large perpendicular orbital magneti…
The Fe/MgO interface is an essential ingredient in spintronics as it shows giant tunneling magnetoresistance and strong perpendicular magnetic anisotropy (PMA). A recent study demonstrated that the insertion of an ultra-thin LiF layer between the Fe and MgO layers enhances PMA significantly. In this study, we perform x-ray magnetic circular dichroism measurements on Fe/LiF/MgO multilayers to reveal the origin of the PMA enhancement. We find that the LiF insertion increases the orbital-magnetic-moment anisotropy and thus the magnetic anisotropy energy. We attribute the origin of this orbital-ma…
Perpendicularly magnetized spin injector with high Curie temperature is a prerequisite for developing spin optoelectronic devices on 2D materials working at room temperature (RT) with zero applied magnetic field. Here, we report the growth of Ta/CoFeB/MgO structures with a large perpendicular magnetic anisotropy (PMA) on full coverage monolayer (ML) MoS2. A large perpendicular interface anisotropy energy of 0.975mJ/m2 has been obtained at the CoFeB/MgO interface, comparable to that observed in magnetic tunnel junction systems. It is found that the insertion of MgO between the ferromagnetic met…
The origin of large perpendicular magneto-crystalline anisotropy (PMCA) in Fe/MgO (001) is revealed by comparing Fe layers with and without the MgO. Although Fe-O $p$-$d$ hybridization is weakly present, it cannot be the main origin of the large PMCA as claimed in previous study. Instead, perfect epitaxy of Fe on the MgO is more important to achieve such large PMCA. As an evidence, we show that the surface layer in a clean free-standing Fe (001) dominantly contributes to $E_{MCA}$, while in the Fe/MgO, those by the surface and the interface Fe layers contribute almost equally. The presence of …
We study the perpendicular magnetic anisotropy (PMA) of the CoFeB/MgO bilayers in contact with W, Ta, IrMn and Ti which has been suggested as the spin-orbit-torque-related underlayers. The saturation magnetization of the CoFeB depends on the underlayer materials due to formation of a dead-layer, affecting PMA strength of each film. The x-ray magnetic circular dichroism measurement reveals that the interfacial intermixing suppresses only the perpendicular orbital moment of Fe, while the intermixing simultaneously suppresses both the perpendicular and in-plane orbital moments of Co.
Thermal stability factor (delta) of recording layer was studied in perpendicular anisotropy CoFeB/MgO magnetic tunnel junctions (p-MTJs) with various CoFeB recording layer thicknesses and junction sizes. In all series of p-MTJs with different thicknesses, delta is virtually independent of the junction sizes of 48-81 nm in diameter. The values of delta increase linearly with increasing the recording layer thickness. The slope of the linear fit is explained well by a model based on nucleation type magnetization reversal.
We show by vector network analyzer ferromagnetic resonance measurements that low Gilbert damping α down to 0.006 can be achieved in perpendicularly magnetized MgO/CoFeB/MgO thin films with ultra-thin insertions of Ta in the CoFeB layer. While increasing the number of Ta insertions allows thicker CoFeB layers to remain perpendicular, the effective areal magnetic anisotropy does not improve with more insertions, and also comes with an increase in α.
The authors studied an effect of ferromagnetic (Co20Fe60B20 or Fe) layer insertion on tunnel magnetoresistance (TMR) properties of MgO-barrier magnetic tunnel junctions (MTJs) with CoFe/Pd multilayer electrodes. TMR ratio in MTJs with CoFeB/MgO/Fe stack reached 67% at an-nealing temperature (Ta) of 200 degree C and then decreased rapidly at Ta over 250 degree C. The degradation of the TMR ratio may be related to crystallization of CoFe(B) into fcc(111) or bcc(011) texture result-ing from diffusion of B into Pd layers. MTJs which were in-situ annealed at 350oC just after depo-siting bottom CoFe…
Magnetic tunnel junction (MTJ) based on CoFeB/MgO/CoFeB structures is of great interest due to its application in the spin-transfer-torque magnetic random access memory (STT-MRAM). Large interfacial perpendicular magnetic anisotropy (PMA) is required to achieve high thermal stability. Here we use first-principles calculations to investigate the magnetic anisotropy energy (MAE) of MgO/CoFe/capping layer structures, where the capping materials include 5d metals Hf, Ta, Re, Os, Ir, Pt, Au and 6p metals Tl, Pb, Bi. We demonstrate that it is feasible to enhance PMA by using proper capping materials…
We investigated the temperature dependence of the switching current for a perpendicularly magnetized CoFeB film deposited on a nanocrystalline tungsten film with large oxygen content: nc-W(O). The spin Hall angle $|Θ_\mathrm{SH}| \approx 0.22$ is independent of temperature, whereas the switching current increases strongly at low temperature. We show that the nc-W(O) is insensitive to annealing. It thus can be a good choice for the integration of spin Hall driven writing of information in magnetic memory or logic devices that require a high-temperature annealing process during fabrication.
We report measurements of the in-plane magnetoelastic coupling in ultra-thin Ta|CoFeB|MgO layers as a function of uniaxial strain, conducted using a four-point bending apparatus. For annealed samples, we observe a strong dependence on the thickness of the CoFeB layer in the range 1.3-2.0 nm, which can be modeled as arising from a combination of effective surface and volume contributions to the magnetoelastic coupling. We point out that if similar thickness dependence exists for magnetoelastic coupling in response to biaxial strain, then the standard Néel model for the magnetic anisotropy energ…
An unusual crystallographic orientation of hexagonal Ru with a 4-fold symmetry emerging in epitaxial MgO/Ru/Co2FeAl/MgO heterostructures is reported, in which an approximately Ru(02-23) growth attributes to the lattice matching among MgO, Ru, and Co2FeAl. Perpendicular magnetic anisotropy of the Co2FeAl/MgO interface is substantially enhanced as compared with those with a Cr(001) layer. The MTJs incorporating this structure gave rise to the largest tunnel magnetoresistance for perpendicular MTJs using low damping Heusler alloys. The 4-fold-symmetry hexagonal Ru arises from an epitaxial growth …
We show that the magnetic characteristics of Ta|CoFeB|MgO magnetic heterostructures are strongly influenced by doping the Ta underlayer with nitrogen. In particular, the saturation magnetization drops upon doping the Ta underlayer, suggesting that the doped underlayer acts as a boron diffusion barrier. In addition, the thickness of the magnetic dead layer decreases with increasing nitrogen doping. Surprisingly, the interface magnetic anisotropy increases to ~1.8 erg/cm2 when an optimum amount of nitrogen is introduced into the Ta underlayer. These results show that nitrogen doped Ta serves as …
We report on the perpendicular magnetic anisotropy (PMA) behavior of heavy metal (HM)/ Fe alloy/MgO thin film heterostructures after an ultrathin HfO2 passivation layer is inserted between the Fe alloy and the MgO. This is accomplished by depositing one to two atomic layers of Hf onto the Fe alloy before the subsequent rf sputter deposition of the MgO layer. This Hf layer is fully oxidized during the subsequent deposition of the MgO layer, as confirmed by X-ray photoelectron spectroscopy measurements. As the result a strong interfacial perpendicular anisotropy energy density can be achieved wi…
We have measured the bias voltage and field dependence of eigenmode frequencies in a magnetic tunnel junction with MgO barrier. We show that both free layer (FL) and reference layer (RL) modes are excited, and that a cross-over between these modes is observed by varying external field and bias voltage. The bias voltage dependence of the FL and RL modes are shown to be dramatically different. The bias dependence of the FL modes is linear in bias voltage, whereas that of the RL mode is strongly quadratic. Using modeling and micromagnetic simulations, we show that the linear bias dependence of FL…
By submonolayer insertion of Au, Pt, or Pd into Ta / CoFeB / MgO / Ta heterostructures we tune the perpendicular magnetic anisotropy and the coercive field of the ferromagnetic layer. We demonstrate that this has a major influence on the spin Hall switching current density and its dependence on the external magnetic field. Despite a rather small effective spin Hall angle of $θ_\mathrm{SH} \approx -0.07$, we obtain switching current densities as low as $2 \times 10^{10}$ A/m$^2$ with a 2 Å Au interlayer. We find that the Dzyaloshinskii-Moriya interaction parameter $D$ is reduced with Au or Pd i…
We report on perpendicular magnetic anisotropy (PMA) in a Pt/Co2FeAl/MgO sandwiched structure with a thick Co2FeAl layer of 2-2.5 nm. The PMA is thermally stable that the anisotropy energy density Ku is 1.3{\times}106 erg/cm3 for the structure with 2 nm Co2FeAl after annealing at 350 oC. The thicknesses of Co2FeAl and MgO layers greatly affect the PMA. Our results provide an effective way to realize relative thick perpendicularly magnetized Heusler alloy films.
The electric field effect on magnetic anisotropy was studied in an ultrathin Fe(001) monocrystalline layer sandwiched between Cr buffer and MgO tunnel barrier layers, mainly through post-annealing temperature and measurement temperature dependences. A large coefficient of the electric field effect of more than 200 fJ/Vm was observed in the negative range of electric field, as well as an areal energy density of perpendicular magnetic anisotropy (PMA) of around 600 uJ/m2. More interestingly, nonlinear behavior, giving rise to a local minimum around +100 mV/nm, was observed in the electric field …
Spin-transfer-torque magnetic random access memory (STT-MRAM) attracts extensive attentions due to its non-volatility, high density and low power consumption. The core device in STT-MRAM is CoFeB/MgO-based magnetic tunnel junction (MTJ), which possesses a high tunnel magnetoresistance ratio as well as a large value of perpendicular magnetic anisotropy (PMA). It has been experimentally proven that a capping layer coating on CoFeB layer is essential to obtain a strong PMA. However, the physical mechanism of such effect remains unclear. In this paper, we investigate the origin of the PMA in MgO/C…
We investigate thickness series of films of the Heusler alloy Co$_2$FeAl in order to study the effect of annealing on the interface with a MgO layer and on the bulk magnetic properties. Our results reveal that while the perpendicular interface anisotropy constant $K^{\perp}_{\rm S}$ is zero for the as-deposited samples, its value increases with annealing up to a value of $1.14\, \pm \,0.07$~mJ/m$^2$ for the series annealed at 320$^{\rm o}$C and of $2.07\, \pm \,0.7$~mJ/m$^2$ for the 450$^{\rm o}$C annealed series owing to a strong modification of the interface during the thermal treatment. Thi…
Phenomena originated from spin-orbit interaction, such as magnetic anisotropy (MA), Rashba-type interactions, or topological insulators, have drawn huge attention for its intriguing physics. In particular, the search for a novel antiferromagnetic material, with potentially large perpendicular MA (PMA), has been becoming very intensive for next-generation high density memory applications. Here, we propose that substitutions of transition metals Ru and Ir, neighboring and same group elements in the periodic table, for the Rh site in the vicinity of surface can induce a substantially large PMA, u…
Perpendicular magnetic anisotropy (PMA) in ultrathin magnetic structures is a key ingredient for the development of electrically controlled spintronic devices. Due to their relatively large spin-polarization, high Curie temperature and low Gilbert damping the Co-based full Heusler alloys are of special importance from a scientific and applications point of view. Here, we study the mechanisms responsible for the PMA in Pt/Co-based full Heusler alloy/MgO thin films structures. We show that the ultrathin Heusler films exhibit strong PMA even in the absence of magnetic annealing. By means of ferro…
The flow of in-plane current through ultrathin magnetic heterostructures can cause magnetization switching or domain wall nucleation owing to bulk and interfacial effects. Within the magnetic layer, the current can create magnetic instabilities via spin transfer torques (STT). At interface(s), spin current generated from the spin Hall effect in a neighboring layer can exert torques, referred to as the spin Hall torques, on the magnetic moments. Here, we study current induced magnetization switching in perpendicularly magnetized CoFeB/MgO heterostructures with a heavy metal (HM) underlayer. Dep…
Perpendicular magnetic anisotropy (PMA) is a key property of magnetoresistive random access memory (MRAM). To increase areal density of MRAM it is important to find a way to enhance the PMA. Recently a strong enhancement of the PMA by inserting an ultrathin LiF layer at an Fe/MgO interface was reported [T. Nozaki et al., NPG Asia Materials (2022) 14: 5]. To understand the origin of the observed enhancement of the PMA we perform first-principles calculations of magetocrystalline anisotropy energy (MAE) of the following four kind of multilayer structures: Fe/MgO, Fe/LiF/MgO, Fe/FeO/MgO, and Fe/F…
Ta/CoFeB/MgO trilayers with perpendicular magnetic anisotropy are expected to play a key role in the next generation of current and electric field switched memory and logic devices. In this study we use Kerr microscopy alongside electrical transport measurement to gain insight into the underlying switching mechanisms of such devices. We find switching to be a stochastic, domain wall driven process, the speed of which is strongly dependent on the switching current. Kerr imaging shows domain nucleation at the edge of the device which modelling reveals is likely assisted by the perpendicular comp…
We explore the impact of Fe80B20 inserted at both Co$_{20}$Fe$_{80}$B$_{20}$/MgO interfaces of dual-MgO free layers (FLs) in bottom-pinned magnetic tunnel junctions (MTJs). MTJ stacks are annealed for 30 min at 350 $^\circ$C and 400 $^\circ$C in a vacuum after film deposition. Current-in-plane tunneling measurements are carried out to characterize magnetotransport properties of the MTJs. Conventional magnetometry measurements and ferromagnetic resonance are conducted to estimate the saturation magnetization, the effective perpendicular anisotropy field and the Gilbert damping of dual-MgO FLs a…
We investigated the magnetic anisotropy ratio of thin sputtered polycrystalline MgB2 films on MgO substrates. Using high magnetic field measurements, we estimated an anisotropy ratio of 1.35 for T=0 K with an upper critical field of 31.74 T in the parallel case and 23.5 T in the perpendicular case. Direct measurements of a magnetic-field sweep at 4.2 K show a linear behavior, confirmed by a linear fit for magnetic fields perpendicular to the film plane. Furthermore, we observed a change of up to 12% of the anisotropy ratio in dependence of the film thickness.
By use of first-principles electronic structure calculations, we predict that the magnetoresistance of the bcc Co(100)/MgO(100)/bcc Co(100) and FeCo(100)/MgO(100)/FeCo(100) tunneling junctions can be several times larger than the very large magnetoresistance predicted for the Fe(100)/MgO(100)/Fe(100) system. The origin of this large magnetoresistance can be understood using simple physical arguments by considering the electrons at the Fermi energy travelling perpendicular to the interfaces. For the minority spins there is no state with $Δ_1$ symmetry whereas for the majority spins there is onl…
The perpendicular magnetic anisotropy (PMA) arising at the interface between ferromagnetic transition metals and metallic oxides are investigated via first-principles calculations. In this work very large values of PMA up to 3 erg/cm$^2$ at Fe$|$MgO interfaces are reported in agreement with recent experiments. The origin of PMA is attributed to overlap between O-$p_z$ and transition metal $d_{z^2}$ orbitals hybridized with $d_{xz(yz)}$ orbitals with stronger spin-orbit coupling induced splitting around the Fermi level for perpendicular magnetization orientation. Furthemore, it is shown that th…
Magnetic tunnel junctions with perpendicular anisotropy form the basis of the spin-transfer torque magnetic random-access memory (STT-MRAM), which is non-volatile, fast, dense, and has quasi-infinite write endurance and low power consumption. Based on density functional theory (DFT) calculations, we propose an alternative design of magnetic tunnel junctions comprising Fe(n)Co(m)Fe(n)/MgO storage layers with greatly enhanced perpendicular magnetic anisotropy (PMA) up to several mJ/m2, leveraging the interfacial perpendicular anisotropy of Fe/MgO along with a stress-induced bulk PMA discovered w…
In this study, to obtain perpendicular magnetic tunnel junctions (p-MTJs) using half-metallic ferromagnets (HMFs), several methods were developed to induce perpendicular magnetic anisotropy (PMA) in full-Heusler Co2FeSi (CFS) alloy thin layers in an MTJ multilayer composed of a layered CFS/MgO/CFS structure. Oxygen exposure at 2.0 Pa for 10 min after deposition of the bottom CFS layer was effective for obtaining PMA in the CFS layer. One of the reasons for the PMA is the formation of nearly ideal CFS/MgO interfaces due to oxygen exposure before the deposition of the MgO layer. The annealing pr…
We report that strong perpendicular magnetic anisotropy of the ferromagnetic layer in a W/CoFeB/MgO multilayer structure can be established by inserting a Hf layer as thin as 0.25 nm between the W and CoFeB layers. The Hf spacer also allows transmission of spin currents generated by an in-plane charge current in the W layer to apply strong spin torque on the CoFeB, thereby enabling current-driven magnetic switching. The antidamping-like and field-like components of the spin torque exerted on a 1 nm CoFeB layer are of comparable magnitudes in this geometry. Both components originate from the sp…
Voltage control of magnetic anisotropy (VCMA) in magnetic heterostructures is a key technology for achieving energy-efficiency electronic devices with ultralow power consumption. Here, we report the first demonstration of the VCMA effect in novel epitaxial Ru/Co2FeAl(CFA)/MgO heterostructures with interfacial perpendicular magnetic anisotropy (PMA). Perpendicularly magnetized tunnel junctions with the structure of Ru/CFA/MgO were fabricated and exhibited an effective voltage control on switching fields for the CFA free layer. A large VCMA coefficient of 108 (139) fJ/Vm for the CFA film was ach…
We report perpendicular magnetic anisotropy (PMA) in the half-metallic ferromagnetic Heusler alloy Co$_2$Fe$_{0.4}$Mn$_{0.6}$Si (CFMS) in a MgO/CFMS/Pd trilayer stack. PMA is found for CFMS thicknesses between 1 and 2 nm, with a magnetic anisotropy energy density of $K_U = 1.5\times 10^6$ erg/cm$^3$ for t$_{\tiny \textrm{CFMS}} = 1.5$ nm. Both the MgO and Pd layer are necessary to induce the PMA. We measure a tunable anomalous Hall effect, where its sign and magnitude vary with both the CFMS and Pd thickness.
Using first-principles calculations, we elucidate microscopic mechanisms of perpendicular magnetic anisotropy (PMA)in Fe/MgO magnetic tunnel junctions through evaluation of orbital and layer resolved contributions into the total anisotropy value. It is demonstrated that the origin of the large PMA values is far beyond simply considering the hybridization between Fe-3d$ and O-2p orbitals at the interface between the metal and the insulator. On-site projected analysis show that the anisotropy energy is not localized at the interface but it rather propagates into the bulk showing an attenuating o…
We present a study of the dynamic magnetic properties of TiN-buffered epitaxial thin films of the Heusler alloy Fe$_{1.5}$CoGe. Thickness series annealed at different temperatures are prepared and the magnetic damping is measured, a lowest value of $α=2.18\times 10^{-3}$ is obtained. The perpendicular magnetic anisotropy properties in Fe$_{1.5}$CoGe/MgO are also characterized. The evolution of the interfacial perpendicular anisotropy constant $K^{\perp}_{\rm S}$ with the annealing temperature is shown and compared with the widely used CoFeB/MgO interface. A large volume contribution to the per…
We present a theoretical study on interfacial magnetocrystalline anisotropy for Fe/MgAl$_2$O$_4$. This system has a very small lattice mismatch at the interface and therefore is suitable for realizing a fully coherent ferromagnet/oxide interface for magnetic tunnel junctions. On the basis of density functional theory, we calculate the interfacial anisotropy constant $K_{\rm i}$ and show that this system has interfacial perpendicular magnetic anisotropy (PMA) with $K_{\rm i} \approx 1.2\,{\rm mJ/m^2}$, which is a little bit smaller than that of Fe/MgO ($K_{\rm i} \approx$ 1.5--1.7$\,{\rm mJ/m^2…
Despite the crucial role of interfacial perpendicular magnetic anisotropy in Co(Fe)/MgO based magnetic tunnel junction, the underlying mechanism is still being debated. Here, we report an anatomical study of oxygen and Mg effect on Pt/Co bilayers through repeated in-situ anomalous Hall effect measurements, controlled oxygen exposure and Mg deposition in an ultrahigh vacuum system. We found that chemisorbed oxygen not only quenches the effective magnetic moment of the Co surface layer, but also softens its magnetic anisotropy. However, a subsequent Mg dusting on the oxygen pre-exposed Pt/Co sur…
Magnetocrystalline anisotropy at Heusler alloy$|$MgO interfaces have been studied using first principles calculations. It is found that Co terminated Co$_{2}$FeAl$|$MgO interfaces show perpendicular magnetic anisotropy up to 1.31 mJ/m$^2$, while those with FeAl termination exhibit in-plane magnetic anisotropy. Atomic layer resolved analysis indicates that the origin of perpendicular magnetic anisotropy in Co$_{2}$FeAl$|$MgO interfaces can be attributed to the out-of-plane orbital contributions of interfacial Co atoms. At the same time, Co$_{2}$MnGe and Co$_{2}$MnSi interfaced with MgO tend to …
A characteristic dependence of voltage control of perpendicular magnetic anisotropy (VCMA) on oxygen migration at Fe/MgO interfaces was revealed by performing systematic {\it ab initio} study of the energetics of the oxygen path around the interface. We find that the surface anisotropy energy exhibits a Boltzmann sigmoidal behavior as a function of the migrated O-atoms concentration. The obtained variation of the VCMA efficiency factor $β$ reveals a saturation limit beyond a critical concentration of migrated O, about $54\%$, at which the anisotropy switches from perpendicular to in plane. Fur…
Using first-principles calculations, we investigated the impact of chromium (Cr) and vanadium (V) impurities on the magnetic anisotropy and spin polarization in Fe/MgO magnetic tunnel junctions. It is demonstrated using layer resolved anisotropy calculation technique, that while the impurity near the interface has a drastic effect in decreasing the perpendicular magnetic anisotropy (PMA), its position within the bulk allows maintaining high surface PMA. Moreover, the effective magnetic anisotropy has a strong tendency to go from in-plane to out-of-plane character as a function of Cr and V conc…
Single-crystal Heusler atomic-scale superlattices that have been predicted to exhibit perpendicular magnetic anisotropy and half-metallicity have been successfully grown by molecular beam epitaxy. Superlattices consisting of full-Heusler Co$_2$MnAl and Fe$_2$MnAl with one to three unit cell periodicity were grown on GaAs (001), MgO (001), and Cr (001)/MgO (001). Electron energy loss spectroscopy maps confirmed clearly segregated epitaxial Heusler layers with high cobalt or high iron concentrations for samples grown near room temperature on GaAs (001). Superlattice structures grown with an exce…
Future generations of magnetic random access memory demand magnetic tunnel junctions that can provide simultaneously high magnetoresistance, strong retention, low switching energy and small cell size below 10nm. Here we study perpendicular magnetic tunnel junctions with composite free layers where multiple ferromagnet/nonmagnet interfaces can contribute to the thermal stability. Different nonmagnetic materials (MgO, Ta, Mo) have been employed as the coupling layers in these multi-interface free layers. The evolution of junction properties under different annealing conditions is investigated. A…
We show that Py, a commonly-used soft ferromagnetic material with weak anisotropy, can become perpendicularly-magnetized while depositing on Ta buffer layer with Hf or Zr insertion layers (ILs) and MgO capping layer. By using two different approaches, namely harmonic voltage measurement and hysteresis loop shift measurement, the dampinglike spin-orbit torque (DL-SOT) efficiencies from Ta/IL/Py/IL/MgO magnetic heterostructures with perpendicular magnetic anisotropy are characterized. We find that though Ta has a significant spin Hall effect, the DL-SOT efficiencies are small in systems with the…
Electric field effects in ferromagnetic/oxide dielectric structures provide a new route to control domain wall (DW) dynamics with low power dissipation. However, electric field effects on DW velocities have only been observed so far in the creep regime where DW velocities are low due to strong interactions with pinning sites. Here, we show gate voltage modulation of DW velocities ranging from the creep to the flow regime in Ta/Co40Fe40B20/MgO/TiO2 structures with perpendicular magnetic anisotropy. We demonstrate a universal description of the role of applied electric fields in the various pinn…
We investigated the low temperature performance of CoFeB/MgO based perpendicular magnetic tunnel junctions (pMTJs) by characterizing their quasi-static switching voltage, high speed pulse write error rate and endurance down to 9 K. pMTJ devices exhibited high magnetoresistance (>120%) and reliable (error rate<10-4) bi-directional switching with 2 to 200 ns voltage pulses. The endurance of the devices at 9 K surpassed that at 300 K by three orders of magnitude under the same write conditions, functioning for more than 10^12 cycles with 10 ns write pulses. The critical switching voltage at 9 K w…
We study interfacial magnetocrystalline anisotropies in various Fe/semiconductor heterostructures by means of first-principles calculations. We find that many of those systems show perpendicular magnetic anisotropy (PMA) with a positive value of the interfacial anisotropy constant $K_{\rm i}$. In particular, the Fe/CuInSe$_2$ interface has a large $K_{\rm i}$ of $\sim 2.3\,{\rm mJ/m^2}$, which is about 1.6 times larger than that of Fe/MgO known as a typical system with relatively large PMA. We also find that the values of $K_{\rm i}$ in almost all the systems studied in this work follow the we…
Thin electrodes of magnetic tunnel junctions can show superparamagnetism at surprisingly low temperature. We analysed their thermally induced switching for varying temperature, magnetic and electric field. Although the dwell times follow an Arrhenius law, they are orders of magnitude too small compared to a model of single domain activation. Including entropic effects removes this inconsistency and leads to a magnetic activation volume much smaller than that of the electrode. Comparing data for varying barrier thickness then allows to separate the impact of Zeman energy, spin-transfer-torque a…
Towards next-generation spintronics devices, such as computer memories and logic chips, it is necessary to satisfy high thermal stability, low-power consumption and high spin-polarization simultaneously. Here, from first-principles, we investigate thermal stability (both structure and magnetization) and the electric field control of magnetic anisotropy on Co2FeAl (CFA)/MgO. A phase diagram of structural thermal stability of the CFA/MgO interface is illustrated. An interfacial perpendicular-anisotropy, coming from the Fe-O orbital hybridization, provides high magnetic thermal stability and a lo…
Thermal-magnetic noise at ferromagnetic resonance (T-FMR) can be used to measure magnetic perpendicular anisotropy of nanoscale magnetic tunnel junctions (MTJs). For this purpose, T-FMR measurements were conducted with an external magnetic field up to 14 kOe applied perpendicular to the film surface of MgO-based MTJs under a dc bias. The observed frequency-field relationship suggests that a 20 A CoFeB free layer has an effective demagnetization field much smaller than the intrinsic bulk value of CoFeB, with 4PiMeff = (6.1 +/- 0.3) kOe. This value is consistent with the saturation field obtaine…
To get stable perpendicularly magnetized tunnel junctions at small device dimensions, composite free layers that comprise two MgO/FeCoB interfaces as sources of interface anisotropy are generally used. Proper cristallisation and annealing robustness is typically ensured by the insertion of a spacer layer of the early transition metal series within the FeCoB layer. We study the influence of the spacer thickness and growth condition on the switching metrics of tunnel junctions thermally annealed at 400$^\circ$C for the case of 1-4 Å Ta spacers. Thick Ta spacer results in a large anisotropies ind…
The adsorption of MgO molecules on a Fe(001) surface was studied using density functional theory (DFT) and projector augmented wave methods. The energetically most favored configurations for different adsorption sites considered were identified. The most preferable adsorption geometry is when the MgO molecules are parallel to the surface, with Mg in the interstitial site and O in on-top of the Fe atom. During the adsorption of subsequent MgO molecules in this geometry, a sharp, non-oxidized interface is formed between the MgO adlayer and Fe(001) surface. The adsorption of MgO perpendicular to …
