arXivDaily arXiv每日学术速递 周一至周五更新
arXiv周末暂无论文更新,休息一下吧,周末愉快~~
arXiv 1505.03313physics.bio-phcond-mat.softcond-mat.stat-mech
收藏

一个半柔性模型预测活F-肌动蛋白丝对固定壁的聚合力

A semi-flexible model prediction for the polymerization force exerted by a living F-actin filament on a fixed wall

Carlo Pierleoni, Giovanni Ciccotti, Jean-Paul Ryckaert

摘要:

我们考虑了在固定单体化学势μ_1和固定温度T下,具有持久长度lp的单根活性半柔性细丝与自由单体溶液处于化学平衡。虽然长丝的一端在单一单体(解聚)步骤中具有化学活性,但另一端通常接枝到刚性壁上以模拟刚性网络,所考虑的长丝从该刚性网络中出现。平行于接枝壁的第二刚性壁固定在距长丝种子的距离L<<l_p处。在超临界条件下,细丝倾向于生长并撞击到第二表面上,这在合适的条件下(非逃逸细丝状态)停止细丝生长。我们首先建立了巨势,并导出了一些一般性质,特别是细丝的尺寸分布和由活细丝施加在障碍物壁上的力。我们将这种形式主义的半柔性,生活,离散蠕虫链(d-WLC)模型的步长为d和持久长度l_p,撞到一个硬墙。通过原始的Monte-Carlo计算,我们证明了Gholami等人(Phys.Rev.E. 74,(2006),041803)。利用这种普遍形式的活丝,我们发现,平均力施加在墙上的距离L的活丝在实践中L独立,非常接近希尔预测的值,他的表达式是严格有效的刚性丝限制。平均长丝力由长丝与壁接触处的累积尺寸分数x乘以尺寸为L_c ~ L的长丝上的屈曲力的乘积得出。我们讨论了几个后果的L独立的失速力为我们的特定的灯丝模型。

英文摘要:

We consider a single living semi-flexible filament with persistence length l_p in chemical equilibrium with a solution of free monomers at fixed monomer chemical potential mu_1 and fixed temperature T. While one end of the filament is chemically active with single monomer (de)polymerization steps, the other end is grafted normally to a rigid wall to mimick a rigid network from which the filament under consideration emerges. A second rigid wall, parallel to the grafting wall, is fixed at distance L<<l_p from the filament seed. In supercritical conditions the filament tends to grow and impinges onto the second surface which, in suitable conditions (non-escaping filament regime) stops the filament growth. We first establish the grand-potential and derive some general properties, in particular the filament size distribution and the force exerted by the living filament on the obstacle wall. We apply this formalism to the semi-flexible, living, discrete Wormlike chain (d-WLC) model with step size d and persistence length l_p, hitting a hard wall. By original Monte-Carlo calculations we justify the use of the weak bending universal expressions of Gholami et al. (Phys.Rev.E. 74,(2006), 041803) over the whole non escaping filament regime. Employing this universal form for living filaments, we find that the average force exerted by a living filament on a wall at distance L is in practice L independent and very close to the value predicted by Hill, his expression being strictly valid in the rigid filament limit. The average filament force results from the product of the cumulative size fraction x, where the filament is in contact with the wall, times the buckling force on a filament of size L_c ~ L. We discuss several consequences of the L independence of the stalling force for our specific filament model.

机构、总结、中文摘要均由AI分析而来,可能存在错误,请以论文正文为准。

↑