The p-type amorphous/ n-type crystalline silicon (P+ a-Si/N+ c-Si) heterojunction was simulated for developing the solar cells with high conversion efficiency and low cost. The characteristic of such cells with different work function of transparent conductive oxide (TCO) were calculated. The energy band structure, quantum efficiency and electric field are analyzed in detail to understand the mechanism of the heterojunction cell. Our results show that the a-Si/c-Si heterojunction is hypersensitive to the TCO work function, and the TCO work function should be large enough in order to achieve high conversion efficiency for P+ a-Si:H/N+ c-Si solar cell. With the optimized parameters set, the P+ a-Si:H/N+ c-Si solar cell reaches a high efficiency (η) up to 21.849% (FF: 0.866, VOC: 0.861 V, JSC: 29.32 mA/cm2).
For many years the faith of organic photovoltaics has been linked to the one of fullerene, since fullerene has been considered the electron-acceptor of choice in bulk heterojunctions solar cells. In the last years, the number of molecules that can be very competitive in replacing fullerene has increased significantly. In this work, we study by means of different theoretical methods five molecules that have demonstrated to work effectively as acceptors in organic heterojunctions. We discuss the comparison of simulated absorption spectra with the experimental spectra.
In this article, we investigate the effect of prolonged light exposure on silicon heterojunction solar cells. We show that, although light exposure systematicallyimproves solar cell efficiency in the case of devices using intrinsic and p-type layers with optimal thickness, this treatment leads to performance degradation for devices with an insufficiently thick (p) layer on the light-incoming side. Our results indicate that this degradation is caused by a diminution of the (i/p)-layer stack hole-selectivity because of light exposure. Degradation is avoided when a sufficiently thick (p) layer is…
Practical device architectures are proposed here for the implementation of three-terminal heterojunction bipolar transistor solar cells (3T-HBTSCs). These photovoltaic devices, which have a potential efficiency similar to that of multijunction cells, exhibit reduced spectral sensitivity compared with monolithically and series-connected tandem solar cells. In addition, the simplified n-p-n (or p-n-p) structure does not require the use of tunnel junctions. In this framework, four architectures are proposed and discussed in this paper: 1) one in which the top cell is based on silicon and the bott…
Energetic disorder induced leakage current in organic bulk heterojunction solar cells: comprehending the ultra-high open circuit voltage loss at low temperatures
In organic bulk heterojunction solar cells, the donor/acceptor interfacial energy offset ($ΔE$) is found to provide the driving force for efficient charge separation which gives rise to high short circuit current density ($J_\mathrm{sc}$), but a high $ΔE$ inevitably undermines the open circuit voltage ($V_\mathrm{oc}$). In this paper, employing the device model method we calculated the steady state current density-voltage ($J-V$) and the $J_\mathrm{sc}-ΔE$ curves under two different charge separation mechanisms to investigate the optimum driving force required for achieving sizable $V_\mathrm{…
Solar modules are currently characterized at standard test conditions (STC), defined at 1000W/m2 and 25 °C. However, solar modules in actual outdoor operating conditions typically operate at lower illumination and higher temperature than STC, which significantly affects their performance ratio (average harvesting efficiency over efficiency in STC). Silicon heterojunction (SHJ) technology displays both good temperature coefficient and good low-illumination performances, leading to outstanding performance ratios. We investigate here SHJ solar cells that use a-SiCx(n) layer as front doped layer w…
Absence of Structural Impact of Noble Nanoparticles on P3HT: PCBM Blends for Plasmon Enhanced Bulk-Heterojunction Organic Solar Cells Probed by Synchrotron Grazing Incidence X-Ray Diffraction
Heterojunction Si solar cells exhibit notable performance degradation. We developed the SolDeg platform to model this degradation as electronic defects getting generated by thermal activation across energy barriers over time. First, molecular dynamics simulations were performed to create a-Si/c-Si stacks, using a machine-learning-based Gaussian approximation potential. Second, we created shocked clusters by a cluster blaster. Third, the shocked clusters were analyzed to identify which of them supported electronic defects. Fourth, the distribution of energy barriers that control the generation …
Silicon heterojunction (SHJ) solar cells represent a promising technological approach towards higher photovoltaics efficiencies and lower fabrication cost. While the device physics of SHJ solar cells have been studied extensively in the past, the ways in which nanoscopic electronic processes such as charge-carrier generation, recombination, trapping, and percolation affect SHJ device properties macroscopically have yet to be fully understood. We report the study of atomic scale current percolation at state-of-the-art a-Si:H/c-Si heterojunction solar cells under ambient operating conditions, re…
Organic solar cells (OSCs) containing an active layer consisting of a nanostructured blend of a conjugated polymer like poly(3-hexylthiophene) (P3HT) and an electron acceptor molecule have the potential of competing against silicon-based photovoltaic panels. However, this potential is unfulfilled primarily due to interrelated production and stability issues. The generally employed spin coating process for fabricating organic solar cells cannot be scaled up. Recently, He et al., have reported that the gelation of P3HT with [6,6]-phenyl-C61-butyric acid methyl ester (PC60BM) under sub-ambient co…
We investigate nongeminate recombination in organic solar cells based on copper phthalocyanine (CuPc) and C$_{60}$. Two device architectures, the planar heterojunction (PHJ) and the bulk heterojunction (BHJ), are directly compared in view of differences in charge carrier decay dynamics. We apply a combination of transient photovoltage (TPV) experiments, yielding the small perturbation charge carrier lifetime, and charge extraction measurements, providing the charge carrier density. In organic solar cells, charge photogeneration and recombination primarily occur at the donor--acceptor heteroint…
Organic heterojunction solar cells are analyzed within a minimal model that includes the essential physical features of such systems. The dynamical properties of this model, calculated using a master equation approach, account for the qualitative behavior of such systems. The model yields explicit results for current-voltage behavior as well as performance characteristics expressed in terms of the thermodynamic efficiency as well as the power conversion efficiency at maximum power, making it possible to evaluate the optimal setup for this device model.
Disentangling Measurement Protocol from Material Physics in Isotypic and Anisotypic SiC/Si Heterojunctions: A Metrology-Driven Study for Betavoltaic Energy Conversion
The performance of organic solar cells strongly depends on the bulk heterojunction (BHJ) morphology of the photoactive layer. This BHJ forms during the drying of the wet-deposited solution, because of physical processes such as crystallization and/or liquid liquid phase separation (LLPS). However, the process-structure relationship remains insufficiently understood. In this work, a recently developed, coupled phase field fluid mechanics framework is used to simulate the BHJ formation upon drying. For the first time, this allows to investigate the interplay between all the relevant physical pro…
Colloidal zinc oxide (ZnO) nanoparticles are frequently used in the field of organic photovoltaics for the realization of solution-producible, electron-selective interfacial layers. Despite of the widespread use, there is a lack of detailed investigations regarding the impact of structural properties of the particles on the device performance. In this work, ZnO nanoparticles with varying surface-area-to-volume ratio were synthesized and implemented into polymer-fullerene bulk heterojunction solar cells with a gas-permeable top electrode. By comparing the electrical characteristics before and a…
Which is conducive to high responsivity in a hybrid graphene-quantum dot transistor: Bulk- or layer- heterojunction
异质结作为光电转换中心，在光电探测中起着至关重要的作用。比较研究了两种典型的基于石墨烯和PbSe量子点的异质结场效应光电晶体管（FEpT）：层异质结（LH）和体异质结（BH）。LH-FEpT具有较高的迁移率（μn）（677 cm ~ 2 V ~（-1）s ~（-1）），而BH-FEpT的μn低至314 cm ~ 2 V ~（-1）s ~（-1），但前者具有较高的响应度（106 A/W）。因为R与迁移率和转移率的乘积成正比，并且LH-FEpT的高转移率过度补偿了低迁移率的不足。虽然大面积异质结和高迁移率有利于高浓度的光生载流子，但输运机制的缺乏成为BH-FEpT的主要限制因素。因此，LH-FEpT是近红外（NIR）光电探测器的较好候选者。
This study outlines the synthesis and physicochemical characteristics of a solution-processable iron manganite (FeMnO3) nanoparticles via a chemical combustion method using tartartic acid as a fuel and demonstrates the performance of this material as a n-type photoactive layer in all-oxide solar cells. It is shown that the solution combustion synthesis (SCS) method enables the formation of pure crystal phase FeMnO3 with controllable particle size. XRD pattern and morphology images from TEM confirm the purity of FeMnO3 phase and the relative small crystallite size (~13 nm), firstly reported in …
We have employed state-of-the-art cross-correlation noise spectroscopy to study carrier dynamics in silicon heterojunction solar cells, complimented by SENTARUS simulations of the same devices. These cells were composed of a light absorbing n-doped crystalline silicon layer contacted by passivating layers of i-a-Si:H and doped a-Si:H electrode layers. The method provided a two-orders-of-magnitude improved sensitivity and allowed to resolution of three additional contributions to noise in addition to 1/f noise. We have observed shot noise with Fano factor close to unity. We have also observed a…
Hybrid conjugated polymer/fullerene filaments based on MEH-PPV/PVP/PCBM are prepared by electrospinning, and their properties assessed by scanning electron, atomic and lateral force, tunnelling, and confocal microscopy, as well as by attenuated total reflection Fourier transform-infrared spectroscopy, photoluminescence quantum yield and spatially-resolved fluorescence. Highlighted features include ribbon-shape of the realized fibers, and the persistence of a network serving as a template for heterogeneous active layers in solar cell devices. A set of favorable characteristics is evidenced in t…
We report the influence of the AlN interlayer thickness (0-15 nm) on the photovoltaic properties of Al0.37In0.63N on Si heterojunction solar cells deposited by radio frequency sputtering. The poor junction band alignment and the presence of a 2-3 nm thick amorphous layer at the interface mitigates the response in devices fabricated by direct deposition of n-AlInN on p-Si(111). Adding a 4-nm-thick AlN buffer layer improves the AlInN crystalline quality and the interface alignment leading to devices with a conversion efficiency of 1.5% under 1-sun AM1.5G illumination. For thicker buffers the per…
High-entropy oxides (HEOs), as multi-component ceramics with high configurational entropy, have been of recent interest due to their attractive properties including photocatalytic activity for H2 production and CO2 conversion. However, the photocatalytic activity of HEOs is still limited to ultraviolet light. In this study, to achieve visible-light-driven photocatalysis, 10 different heterojunctions were simultaneously introduced in the Ti-Zr-Nb-Ta-W-O system. The oxide, which was synthesized by a high-pressure torsion method and oxidation, successfully produced oxygen from water under visible…
