We study static and dynamic magnetic properties of Co2MnGe (13 nm)/Al2O3 (3 nm)/Co (13 nm) tunnel magnetic junctions (TMJ), deposited on various single crystalline substrates (a-plane sapphire, MgO(100), Si(111)). The results are compared to the magnetic properties of Co and of Co$_{2}$MnGe single films lying on sapphire substrates. X-rays diffraction always shows a (110) orientation of the Co$_{2}$MnGe films. Structural observations obtained by high resolution transmission electron microscopy confirmed the high quality of the TMJ grown on sapphire. Our vibrating sample magnetometry measurements reveal in-plane anisotropy only in samples grown on a sapphire substrate. Depending on the substrate, the ferromagnetic resonance spectra of the TMJs, studied by the microstrip technique, show one or two pseudo-uniform modes. In the case of MgO and of Si substrates only one mode is observed: it is described by magnetic parameters (g-factor, effective magnetization, in-plane magnetic anisotropy) derived in the frame of a simple expression of the magnetic energy density; these parameters are practically identical to those obtained for the Co single film. With a sapphire substrate two modes are present: one of them does not appreciably differ from the observed mode in the Co single film while the other one is similar to the mode appearing in the Co$_{2}$MnGe single film: their magnetic parameters can thus be determined independently, using a classical model for the energy density in the absence of interlayer exchange coupling.
MnGe has been grown as a thin film on Si(111) substrates by molecular beam epitaxy. A 10 Å layer of MnSi was used as seedlayer in order to establish the B20 crystal structure. Films of a thickness between 45 and 135 Å have been prepared and structually characterized by RHEED, AFM and XRD. These techniques give evidence that MnGe forms in the cubic B20 crystal structure as islands exhibiting a very smooth surface. The islands become larger with increasing film thickness. A magnetic characterization reveals that the ordering temperature of MnGe thin films is enhanced compared to bulk material. T…
We report on the first integration of an antiferromagnetic Heusler compound acting as a pinning layer into magnetic tunneling junctions. The antiferromagnet Ru$_2$MnGe is used to pin the magnetization direction of a ferromagnetic Fe layer in MgO based thin film tunnelling magnetoresistance stacks. The samples were prepared using magnetron co-sputtering. We investigate the structural properties by X-ray diffraction and reflection, as well as atomic force and high-resolution transmission electron microscopy. We find an excellent crystal growth quality with low interface roughnesses of 1-3 Å, whi…
Skyrmions are localized magnetic spin textures whose stability has been shown theoretically to depend on material parameters including bulk Dresselhaus spin orbit coupling (SOC), interfacial Rashba SOC, and magnetic anisotropy. Here, we establish the growth of a new class of artificial skyrmion materials, namely B20 superlattices, where these parameters could be systematically tuned. Specifically, we report the successful growth of B20 superlattices comprised of single crystal thin films of FeGe, MnGe, and CrGe on Si(111) substrates. Thin films and superlattices are grown by molecular beam epi…
Spin polarized scanning tunneling microscopy is used to directly image topological magnetic textures in thin films of MnGe, and to correlate the magnetism with structure probed at the atomic-scale. Our images indicate helical stripe domains, each characterized by a single wavevector Q, and their associated helimagnetic domain walls, in contrast to the 3Q magnetic state seen in the bulk. Combining our surface measurements with micromagnetic modeling, we deduce the three-dimensional orientation of the helical wavevectors and gain detailed understanding of the structure of individual domain walls…
We carefully investigate three important effects including postgrowth activation annealing, delta (δ) dose and p+-GaN layer thickness and experimentally demonstrate their influence on the electrical properties of GaN p-n homojunction diodes with a tunnel junction (TJ)-based p-contact. The p-n diodes and TJ structures were monolithically grown by metalorganic chemical vapor deposition (MOCVD) in a single growth step. By optimizing the annealing time and temperature for magnesium (Mg) activation and introducing δ-doses for both donors and acceptors at TJ interfaces, a significant improvement in …
Magnetocrystalline anisotropy at Heusler alloy$|$MgO interfaces have been studied using first principles calculations. It is found that Co terminated Co$_{2}$FeAl$|$MgO interfaces show perpendicular magnetic anisotropy up to 1.31 mJ/m$^2$, while those with FeAl termination exhibit in-plane magnetic anisotropy. Atomic layer resolved analysis indicates that the origin of perpendicular magnetic anisotropy in Co$_{2}$FeAl$|$MgO interfaces can be attributed to the out-of-plane orbital contributions of interfacial Co atoms. At the same time, Co$_{2}$MnGe and Co$_{2}$MnSi interfaced with MgO tend to …
We have studied transport properties of Nb/Al/AlOx/Nb tunnel junctions with ultrathin aluminum oxide layers formed by (i) thermal oxidation and (ii) plasma oxidation, before and after rapid thermal post-annealing of the completed structures at temperatures up to 550 deg C. Post-annealing at temperatures above 300 deg C results in a significant decrease of the tunneling conductance of thermally-grown barriers, while plasma-grown barriers start to change only at annealing temperatures above 450 deg C. Fitting the experimental I-V curves of the junctions using the results of the microscopic theor…
InGaN/GaN tunnel junction contacts were grown on top of an InGaN/GaN blue (450 nm) light emitting diode wafer using plasma assisted molecular beam epitaxy. The tunnel junction contacts enable low spreading resistance n-GaN top contact layer thereby requiring less top metal contact coverage on the surface. A voltage drop of 5.3 V at 100 mA, forward resistance of 2 x 10-2 ohm cm2 and a higher light output power are measured in tunnel junction LED. A low resistance of 5 x 10-4 ohm cm2 was measured in a MBE grown tunnel junction on GaN PN junction device, indicating that the tunnel junction LED de…
An efficient electrical spin injection into an InGaAs/GaAs quantum well light emitting diode is demonstrated thanks to a CoFeB/MgO spin injector. The textured MgO tunnel barrier is fabricated by two different techniques: sputtering and molecular beam epitaxy (MBE). The maximal spin injection efficiency is comparable for both methods. Additionally, the effect of annealing is also investigated for the two types of samples. Both samples show the same trend: an increase of the electroluminescence circular polarization (Pc) with the increase of annealing temperature, followed by a saturation of Pc …
We show evidence that tunnel junctions (TJs) in GaN grown by metal-organic vapor phase epitaxy are dominated by trap-assisted (Poole-Frenkel) tunneling. This stems from observations of the careful optimized doping for the TJs. Especially the p$^{++}$ and the n$^{++}$ layers are far from ideal. The n$^{++}$ layer induces 3D growth, which can be seen by a rising oxygen signal in Secondary Ions Mass Spectroscopy (SIMS). Furthermore, Mg segregation observed by SIMS indicates a depletion region of more than 10 nm. Still, we could realize TJ based LEDs with a low penalty voltage of 1.1 V and a speci…
We report resistance versus magnetic field measurements for a La0.65Sr0.35MnO3/SrTiO3/La0.65Sr0.35MnO3 tunnel junction grown by molecular-beam epitaxy, that show a large field window of extremely high tunneling magnetoresistance (TMR) at low temperature. Scanning the in-plane applied field orientation through 360^/circ, the TMR shows 4-fold symmetry, i.e. biaxial anisotropy, aligned with the crystalline axes but not the junction geometrical long axis. The TMR reaches ~ 1900% at 4K, corresponding to an interfacial spin polarization of > 95% assuming identical interfaces. These results show that…
Ultra-thin oxide (UTO) films were grown on Si(111) in ultrahigh vacuum at room temperature and characterized by scanning tunneling microscopy. The ultra-thin oxide films were then used as substrates for room temperature growth of pentacene. The apparent height of the first layer is 1.57 +/- 0.05 nm, indicating standing up pentacene grains in the thin-film phase were formed. Pentacene is molecularly resolved in the second and subsequent molecular layers. The measured in-plane unit cell for the pentacene (001) plane (ab plane) is a=0.76+/-0.01 nm, b=0.59+/-0.01 nm, and gamma=87.5+/-0.4 degrees. …
HRTEM, nano-beam electronic diffraction, energy dispersive X-rays scanning spectroscopy, Vibrating Sample Magnetometry (VSM) and FerroMagnetic Resonance (FMR) techniques are used in view of comparing (static and dynamic) magnetic and structural properties of Co2MnGe (13 nm)/Al2O3 (3 nm)/Co (13 nm) tunnel magnetic junctions (TMJ), deposited on various single crystalline substrates (a-plane sapphire, MgO(100) and Si(111)). They allow for providing a correlation between these magnetic properties and the fine structure investigated at atomic scale. The Al2O3 tunnel barrier is always amorphous and …
Magnetic tunnel junctions (MTJ) have been grown by using molecular beam epitaxy on c-plane Al2O3 substrates. The MTJ stacks consist of two ferromagnetic hcp-Co layers separated by a thin insulating h-BN barrier. The samples have been grown in a single run revealing single crystalline epitaxial structures with sharp interfaces as observed by applying transmission electron microscopy. The in-plane magnetization experiments have revealed separate magnetization switching of a thin top Co (soft) layer and a thick bottom Co (hard) layer. At zero magnetic field the two Co layers are found in an antip…
Monolayer Tellurium (Te) or tellurene has been suggested by a recent theory as a new two-dimensional (2D) system with great electronic and optoelectronic promises. Here we present an experimental study of epitaxial Te deposited on highly oriented pyrolytic graphite (HOPG) substrate by molecular-beam epitaxy. Scanning tunneling microscopy of ultrathin layers of Te reveals rectangular surface cells with the cell size consistent with the theoretically predicted beta-tellurene, whereas for thicker films, the cell size is more consistent with that of the (10-10) surface of bulk Te crystal. Scanning…
The surface stabilized MnO(100)-like monolayer, characterised by a regular c(4x2) distribution of Mn vacancies, is studied by hybrid functionals and discussed in the light of available scanning tunneling microscopy and high-resolution electron energy loss spectroscopy data. We show that the use of hybrid functionals is crucial to account for the intermingled nature of magnetic ineractions, electron localization, structural distortions and surface phonons. The proposed Pd(100) supported Mn3O4 structure is excellently compatible with the experiments previously reported in literature.
Two-dimensional materials with layered structures, appropriate bandgap, and high carrier mobilities have gathered tremendous interests due to their potential applications in optoelectronic and photovoltaic devices. Here, we report the growth of BiI3 thin film with controllable atomic thickness on graphene-terminated 6H-SiC(0001) substrate by molecular beam epitaxy (MBE) method. The growth kinetic processes and crystalline properties of the BiI3 film are studied by scanning tunneling microscopy (STM). The scanning tunneling spectroscopy (STS) reveals a bandgap of 2.8 eV for monolayer BiI3 with …
We demonstrate a method for synthesizing large scale single layer graphene by thermal annealing of ruthenium single crystal containing carbon. Low energy electron diffraction indicates the graphene grows to as large as millimeter dimensions with good long-range order, and scanning tunneling microscope shows perfect crystallinity. Analysis of Moire pattern augmented with first-principles calculations shows the graphene layer is incommensurate with the underlying Ru(0001) surface forming a N by N superlattice with an average lattice strain of ~ +0.81%. Our findings offer an effective method for …
Graphene grown epitaxially on SiC has been proposed as a material for carbon-based electronics. Understanding the interface between graphene and the SiC substrate will be important for future applications. We report the ability to image the interface structure beneath single-layer graphene using scanning tunneling microscopy. Such imaging is possible because the graphene appears transparent at energies of 1 eV above or below the Fermi energy. Our analysis of calculations based on density functional theory shows how this transparency arises from the electronic structure of a graphene layer on a…
The transition metal ions doped with TiO2 films are of magnetic properties at room temperatures and have stimulated many scientists to study other properties. The Co-TiO2 sandwich composite films have been recently grown on glass and silicon substrates by using alternately radio frequency reactive and direct current magnetron sputtering. The microstructural properties of these films were characterized with Raman spectra and X-ray photoemission spectra (XPS). It shows an anatase TiO2 containing Co nano-layer. Optical absorption spectra have red shift with Co nano-layer increasing, which origina…
Self-poled ultra-thin ferroelectric PbZr0.52Ti0.48O3 (PZT) (5 and 7 nm) films have been grown by pulsed laser deposition technique on ferromagnetic La0.67Sr0.33MnO3 (LSMO) (30 nm) to check the effect of polar capping on magnetization for ferroelectric tunnel junction (FTJ) devices. PZT/LSMO heterostructures with thick polar PZT (7 nm) capping show nearly 100% enhancement in magnetization compared with thin polar PZT (5 nm) films, probably due to excess hole transfer from the ferroelectric to the ferromagnetic layers. Core-level X-ray photoelectron spectroscopy studies revealed the presence of …
Two-dimensional molybdenum disulphide on graphene grown by chemical vapour deposition is a promising van der Waals system for applications in optoelectronics and catalysis. To extend the fundamental understanding of growth and intrinsic properties of molybdenum disulphide on graphene, molybdenum disulphide on highly oriented pyrolytic graphite is a suitable model system. Here we show, experimentally and by density-functional-theory calculations, that molybdenum disulphide flakes grow in two orientations. One of the orientations is energetically preferred, the other one is rotated by 30 degree.…
We develop a strategy for graphene growth on Ru(0001) followed by silicon-layer intercalation that not only weakens the interaction of graphene with the metal substrate but also retains its superlative properties. This G/Si/Ru architecture, produced by silicon-layer intercalation approach (SIA), was characterized by scanning tunneling microscopy/spectroscopy and angle resolved electron photoemission spectroscopy. These experiments show high structural and electronic qualities of this new composite. The SIA allows for an atomic control of the distance between the graphene and the metal substrat…
Ferromagnetic resonance (FMR) spin pumping is a rapidly growing field which has demonstrated promising results in a variety of material systems. This technique utilizes the resonant precession of magnetization in a ferromagnet to inject spin into an adjacent non-magnetic material. Spin pumping into graphene is attractive on account of its exceptional spin transport properties. This article reports on FMR characterization of cobalt grown on CVD graphene and examines the validity of linewidth broadening as an indicator of spin pumping. In comparison to cobalt samples without graphene, direct con…
Giant tunnel magnetoresistance (TMR) ratios of 417% at room temperature (RT) and 914% at 3 K were demonstrated in epitaxial Fe/MgO/Fe(001) exchanged-biased spin-valve magnetic tunnel junctions (MTJs) by tuning growth conditions for each layer, combining sputter deposition for the Fe layers, electron-beam evaporation of the MgO barrier, and barrier interface tuning. Clear TMR oscillation as a function of the MgO thickness with a large peak-to-valley difference of ~80% was observed when the layers were grown on a highly (001)-oriented Cr buffer layer. Specific features of the observed MTJs are s…
We have investigated the magnetotransport properties of La0.7Sr0.3MnO3/BaTiO3 superlattices, grown on SrTiO3 substrate by pulsed laser deposition technique, both with current-in-plane and current-perpendicular-to-the-plane directions. Several features indicate the presence of magnetic inhomogeneities at the interfaces which is independent of BaTiO3 layer thickness variation. First, the magnetic property in the superlattices decreases. Second, a hysteresis in magnetoresistance due to the relaxation of the resistive state is observed. Third, a threshold under an applied magnetic field in the mag…
In-plane compressively strained $α$-Sn films have been theoretically predicted and experimentally proven to possess non-trivial electronic states of a 3D topological Dirac semimetal. The robustness of these states typically strongly depends on purity, homogeneity and stability of the grown material itself. By developing a reliable fabrication process, we were able to grow pure strained $α$-Sn films on InSb(100), without heating of the substrate during growth, nor using any dopants. The $α$-Sn films were grown by molecular beam epitaxy, followed by experimental verification of the achieved chem…
This letter describes a new inorganic shadow mask that has been employed for the evaporation of all-epitaxial Al/Al2O3/Al superconducting tunnel junctions. Organic resists that are commonly used for shadow masks and other lift-off processes are not compatible with ultra-high vacuum deposition systems, and they can break down at even moderately elevated temperatures. The inorganic mask described herein does not suffer these same shortcomings. It was fabricated from a Ge/Nb bilayer, comprising suspended Nb bridges supported by an undercut Ge sacrificial layer. Utilizing such a bilayer mask on C-…
Single- and few-layer chromium triiodide (CrI3), which has been intensively investigated as a promising platform for two-dimensional magnetism, was usually prepared by mechanical exfoliation. Here, we report on the growth of single-layer CrI3 by molecular beam epitaxy under ultrahigh vacuum. The atomic structures and local density of states have been revealed by scanning tunneling microscopy (STM). Iodine trimers, each of which consists of three I atoms surrounding a three-fold Cr honeycomb center, have been identified as the basic units of the topmost I layer. Different superstructures of sin…
Layer thickness dependent band gap of MBE grown single- to few-layer MoS$_{2}$
Institute of Physics, University of Münster（明斯特大学物理研究所）；Institute of Solid State Theory, University of Münster（明斯特大学凝聚态理论研究所）；Institute of Physics, Poznan University of Technology（波兹南理工大学物理研究所）
The equiatomic quaternary Heusler alloy CoFeCrAl is a candidate material for spin-gapless semiconductors (SGSs). However, to date, there have been no experimental attempts at fabricating a junction device. This paper reports a fully epitaxial (001)-oriented MgO barrier magnetic tunnel junction (MTJ) with CoFeCrAl electrodes grown on a Cr buffer. X-ray and electron diffraction measurements show that the (001) CoFeCrAl electrode films with atomically flat surfaces have a $B2$-ordered phase. The saturation magnetization is 380 emu/cm$^3$, almost the same as the value given by the Slater--Pauling-…
We report a complementary metal oxide semiconductor (CMOS) technology compatible ferroelectric tunnel junction memristor grown directly on top of a Silicon substrate using a scandium doped aluminum nitride as the ferroelectric layer.
Co-rich Co$_{1-x}$Mn$_x$ alloys have hcp or fcc disordered phases and those ferromagnetic orderings are significantly deteriorated with increasing Mn concentration $x$ in bulk. On the other hand, those metastable bcc phases show properties attractive to spintronics, e.g., high tunnel magnetoresistance (TMR) ratio of more than 200% (600%) at 300 K (10 K) in magnetic tunnel junctions (MTJs) with the $x$ = 0.25 bcc alloy electrodes [Kunimatsu et al., Appl. Phys. Express 13, 083007 (2020)]. Here, we report systematic study of structure and magnetism for epitaxial thin films as well as the TMR effe…
We report on the design, fabrication, and characterization of GaN interband tunnel junction showing forward tunneling characteristics. We have achieved very high forward tunneling currents (153 mA/cm2 at 10 mV, and 17.7 A/cm2 peak current) in polarization-engineered GaN/InGaN/GaN heterojunction diodes grown by plasma assisted molecular beam epitaxy. We also report the observation of repeatable negative differential resistance in interband III-Nitride tunnel junctions, with peak-valley current ratio (PVCR) of 4 at room temperature. The forward current density achieved in this work meets the typ…
The knowledge of chemical and magnetic conditions at the Co40Fe40B20 / MgO interface is important to interpret the strong annealing temperature dependence of tunnel magnetoresistance of Co-Fe-B / MgO / Co-Fe-B magnetic tunnel junctions, which increases with annealing temperature from 20% after annealing at 200C up to a maximum value of 112% after annealing at 350C. While the well defined nearest neighbor ordering indicating crystallinity of the MgO barrier does not change by the annealing, a small amount of interfacial Fe-O at the lower Co-Fe-B / MgO interface is found in the as grown samples,…
Co islands grown on Cu(111) with a stacking fault at the interface present a conductance in the empty electronic states larger than the Co islands that follow the stacking sequence of the Cu substrate. Electrons can be more easily injected into these faulted interfaces, providing a way to enhance transmission in future spintronic devices. The electronic states associated to the stacking fault are visualized by tunneling spectroscopy and its origin is identified by band structure calculations.
Sandwich-type all-MgB2 Josephson tunnel junctions (MgB2/AlOx/MgB2) have been fabricated for the first time with as-grown MgB2 films formed by molecular beam epitaxy. The junctions exhibit substantial superconducting current (IcRN product ~ 0.8 mV at 4.2K), a well-defined superconducting gap (delta = ~2.3 mV), and clear Fraunhofer patterns. The superconducting gap voltage of delta agrees well with the smaller gap in the multi-gap scenario. The results demonstrate that MgB2 has great promise for superconducting electronics that can be operated at T ~ 20 K.
La2/3Ca1/3MnO3 thin films have been grown on yttria-stabilized zirconia (YSZ) buffered silicon-on-insulator (SOI) substrate by the pulsed laser deposition technique. While full cube-on-cube epitaxy was achieved for the YSZ layer, the top manganite layer was multi-domain-oriented, with a coexistence of cube-on-cube and cube-on-diagonal epitaxy. Due to a combined influence from the magnetocrystalline anisotropy and the magnetoelastic anisotropy, in zero field the local spin orientation varies across the twin boundaries. As a result, a quite large low-field magnetoresistance (LFMR) based on spin-…
This work studies the effect of four different types of buffer layers on the structural and optical properties of InGaN layers grown on Si(111) substrates and their correlation with electrical characteristics. The vertical electrical conduction of n-InGaN/buffer-layer/p-Si heterostructures, with In composition near 46%, which theoretically produces an alignment of the bands, is analyzed. Droplet elimination by radical-beam irradiation was successfully applied to grow high quality InGaN films on Si substrates for the first time. Among several buffer choices, an AlN buffer layer with a thickness…
We investigated the influence of n+-GaAs thickness and doping density of GaMnAs/n+-GaAs Esaki tunnel junction on the efficiency of the electrical electron spin injection. We prepared seven samples of GaMnAs/n+-GaAs tunnel junctions with different n+-GaAs thickness and doping density grown on identical p-AlGaAs/p-GaAs/n-AlGaAs light emitting diode (LED) structures. Electroluminescence (EL) polarization of the surface emission was measured under the Faraday configuration with external magnetic field. All samples have the bias dependence of the EL polarization, and higher EL polarization is obtai…
Reflection high energy electron diffraction (RHEED), scanning tunneling microscopy (STM), vibrating sample magnetometry and other physical property measurements are used to investigate the structure, morphology, magnetic and magneto-transport properties of (001)-oriented Cr$_2$Te$_3$ thin films grown on Al$_2$O$_3$(0001) and Si(111)-(7$\times$7) surfaces by molecular beam epitaxy (MBE). Streaky RHEED patterns indicate flat smooth film growth on both substrates. STM studies show the hexagonal arrangements of surface atoms. Determination of the lattice parameter from atomically resolved STM imag…
Chromium selenide thin films were grown epitaxially on Al${_2}$O${_3}$(0001) and Si(111)-(7${\times}$7) substrates using molecular beam epitaxy (MBE). Sharp streaks in reflection high-energy electron diffraction and triangular structures in scanning tunneling microscopy indicate a flat smooth film growth along the c-axis, and is very similar to that from a hexagonal surface. X-ray diffraction pattern confirms the growth along the c-axis with c-axis lattice constant of 17.39 Å. The grown film is semiconducting, having a small band gap of about 0.034 eV, as calculated from the temperature depend…
We report on the design and demonstration of polarization-engineered GaN/InGaN/GaN tunnel junction diodes with high current density and low tunneling turn-on voltage. Wentzel-Kramers-Brillouin (WKB) calculations were used to model and design tunnel junctions with narrow bandgap InGaN-based barrier layers. N-polar p-GaN/In0.33Ga0.67N/n-GaN heterostructure tunnel diodes were grown using molecular beam epitaxy. Efficient zero bias tunneling turn-on with a high current density of 118 A/cm2 at a reverse bias of 1V, reaching a maximum current density up to 9.2 kA/cm2 were obtained. These results rep…
Heterostructures made by stacking different materials on top of each other are expected to exhibit unusual properties and new phenomena. Interface of the heterostructures plays a vital role in determining their properties. Here, we report the observation of a two-dimensional (2D) spinodal interface in graphene-molybdenum carbide (α-Mo2C) heterostructures, which arises from spinodal decomposition occurring at the heterointerface, by using scanning tunneling microscopy. Our experiment demonstrates that the 2D spinodal interface modulates graphene into whispering gallery resonant networks filled …
A ferroelectric tunnel barrier in between two ferromagnetic electrodes (multiferroic tunnel junction, MFTJ), is one of the most promising concepts for future microelectronic devices. In parallel, Hafnia based ferroelectrics are showing great potential for device miniaturization down to the nanoscale. Here we utilize ferroelectric Hf0.5Zr0.5O2 (HZO) with thickness of only 2 nm, epitaxially grown on La0.7Sr0.3MnO3 (LSMO) ferromagnetic electrodes, as a large band-gap insulating barrier integrated in MFTJs with cobalt top electrodes. As previously reported for other MFTJs with similar electrodes, …
Blue light-emitting diodes (LEDs) consisting of a buried n+-p+ GaN tunnel junction, (In,Ga)N multiple quantum wells (MQWs) and a n+-GaN top layer are grown on single-crystal Ga-polar n+-GaN bulk wafers by plasma-assisted molecular beam epitaxy. The (In,Ga)N MQW active regions overgrown on the p+-GaN show chemically abrupt and sharp interfaces in a wide range of compositions and are seen to have high structural and optical properties as verified by X-ray diffraction and spatially resolved cathodoluminescence measurements. The processed LEDs reveal clear rectifying behavior with a low contact an…
While the growth of germanene has been claimed on many substrates, the exact crystal structures remain controversial. Here, we systematically explore the possible structures formed by Ge deposition onto Al(111) surface by combining density-functional theory (DFT) and global optimization algorithm. We show that, by high-level random-phase approximation (RPA) calculations, the formation of germanene on Al(111) is energetically unfavorable with positive formation energy. The two experimental phases are identified as honeycomb alloys Al3Ge3/Al(111)(r7xr7) and Al3Ge4/Al(111)(3x3), by combining ab i…
The evidence for proximity-induced superconductivity in heterostructures of topological insulators and high-Tc cuprates has been intensely debated. We use molecular beam epitaxy to grow thin films of topological insulator Bi2Te3 on a cuprate Bi2Sr2CaCu2O8+x, and study the surface of Bi2Te3 using low-temperature scanning tunneling microscopy and spectroscopy. In few unit-cell thick Bi2Te3 films, we find a V-shaped gap-like feature at the Fermi energy in dI/dV spectra. By reducing the coverage of Bi2Te3 films to create nanoscale islands, we discover that this spectral feature dramatically evolve…
The superconductor Sn$_{1-x}$In$_{x}$Te is derived from the topological crystalline insulator SnTe and is a candidate topological superconductor. So far, high-quality thin films of this material have not been available, even though such samples would be useful for addressing the nature of its superconductivity. Here we report the successful molecular beam epitaxy growth of superconducting Sn$_{1-x}$In$_{x}$Te films by using Bi$_2$Te$_3$ as a buffer layer. The data obtained from tunnel junctions made on such films show the appearance of two superconducting gaps, which points to the coexistence …
The Fe/MgO magnetic tunnel junction is a classic spintronic system, with current importance technologically, and interest for future innovation. The key magnetic properties are linked directly to the structure of hard-to-access buried interfaces, and the Fe and MgO components near the surface are unstable when exposed to air, making a deeper probing, non-destructive, in-situ measurement ideal for this system. We have thus applied hard x-ray photoemission spectroscopy (HXPS) and standing-wave (SW) HXPS in the few keV energy range to probe the structure of an epitaxially-grown MgO/Fe superlattic…
The heteroepitaxial growth of Re (0001) films on Nb (110) surfaces has been investigated. Nb/Re bilayers were grown on A-plane sapphire -- alpha-Al2O3 (11-20) -- by molecular beam epitaxy. While Re grew with a (0001) surface, the in-plane epitaxial relationship with the underlying Nb could be best described as a combination of Kurdjumov-Sachs and Nishiyama-Wassermann orientations. This relationship was true regardless of Re film thickness. However, an evolution of the surface morphology with increasing Re thickness was observed, indicative of a Stranski-Krastanov growth mode. Re (0001) layers …
In ferroelectric materials, spontaneous symmetry breaking leads to a switchable electric polarization, which offers significant promise for nonvolatile memories. In particular, ferroelectric tunnel junctions (FTJs) have emerged as a new resistive switching memory which exploit polarization-dependent tunnel current across a thin ferroelectric barrier. Here we demonstrate FTJs with CMOS-compatible Zr-doped HfO$_2$ (Zr:HfO$_2$) ferroelectric barriers of just 1 nm thickness, grown by atomic layer deposition on silicon. These 1 nm Zr:HfO$_2$ tunnel junctions exhibit large polarization-driven electr…
The recent study of oxides led to the discovery of several new fascinating physical phenomena. High-temperature superconductivity, colossal magnetoresistance, dilute magnetic doping, or multiferroicity were discovered and investigated in transition-metal oxides, representing a prototype class of strongly correlated electronic systems. This development was accompanied by an enormous progress regarding thin film fabrication. Within the past two decades, epitaxial thin films with crystalline quality approaching semiconductor standards became available using laser molecular beam epitaxy. This evol…
Helical magnets are emerging as a novel class of materials for spintronics and sensor applications; however, research on their charge and spin transport properties in a thin film form is less explored. Herein, we report the temperature and magnetic field dependent charge transport properties of a highly crystalline MnP nanorod thin film over a wide temperature range (2-350 K). The MnP nanorod films of 100 nm thickness were grown on Si substrates at 500 oC using molecular beam epitaxy. The temperature dependent resistivity data exhibits a metallic behavior over the entire measured temperature r…
