Flame Synthesis of Graphene Films in Open Environments
Nasir K. Memon, Stephen D. Tse, Jafar F. Al-Sharab, Hisato Yamaguchi, Alem-Mar B. Goncalves, Bernard H. Kear, Yogesh Jaluria, Eva Y. Andrei, Manish Chhowalla
Few-layer graphene (FLG) is grown on copper and nickel substrates at high rates using a novel flame synthesis method in open-atmosphere environments. Transmittance and resistance properties of the transferred films are similar to those grown by other methods, but the concentration of oxygen, as assessed by XPS, is actually less than that for CVD-grown graphene under near vacuum conditions. The method involves utilizing a multi-element inverse-diffusion-flame burner, where post-flame species and temperatures are radially-uniform upon deposition at a substrate. Advantages of the flame synthesis method are scalability for large-area surface coverage, increased growth rates, high purity and yield, continuous processing, and reduced costs due to efficient use of fuel as both heat source and reagent. Additionally, by adjusting local growth conditions, other carbon nanostructures (i.e. nanotubes) are readily synthesized.
The expected high performance of graphene-based electronics is often hindered by lack of adequate doping, which causes low carrier density and large sheet resistance. Many reported graphene doping schemes also suffer from instability or incompatibility with existing semiconductor processing. Here we report ultrahigh and stable p-type doping up to ~7x10^13 1/cm^2 (~2x10^21 1/cm^3}) of monolayer graphene grown by chemical vapor deposition. This is achieved by direct polycrystalline MoO3 growth on graphene using a rapid flame synthesis technique. With this approach, the metal-graphene contact res…
Synergetic Enhancement on Bulk and Grain Boundary Ionic Conduction of Mg Doped High-Entropy NASICON-Type Solid Electrolyte for Solid-State Na+ Batteries by Spray Flame Synthesis
The layer-by-layer (LbL) technique is adopted for the construction of multilayers encompassing chitosan and graphene oxide (GO) platelets capable of improving the flame retardant properties open cell PU foams. The LbL assembly follows a linear growth regime as evaluated by infrared spectroscopy and yields a multilayer structure where GO platelets are embedded within a chitosan continuous matrix. 3 and 6 bi-layers (BL) can efficiently coat the complex 3D structure of the foam and substantially improve its flame retardant properties. 3BL only add 10% to the original mass and can suppress the mel…
Graphene oxide (GO) is regarded as one typical two-dimension structured oxygenated planar molecular material. Researchers across multiple disciplines have paid enormous attention to it due to unique physiochemical properties. However, models used to describe the structure of GO are still in argument and ongoing to update. Currently, synthesis methods for massive production are seemingly abundant but in fact, dominated by few thought systems. We herein aim to give a mini but critical review over the synthesis of graphene oxide as well as its structure, involving relative peer work.
We report on the synthesis of CdSe quantum dots on a graphene surface by an electrochemical deposition method. By using a mesoporous silica film formed on the graphene surface as a template and a potential equalizer between the edge/defect sites and the basal plane of the graphene, CdSe quantum dots can be grown on the basal plane into a regular hexagonal array.
We report on a new method for graphene synthesis and assessment of the properties of the resulting large-area graphene layers. Graphene was produced by the high pressure - high temperature growth from the natural graphitic source by utilizing the molten Fe-Ni catalysts for dissolution of carbon. The resulting large-area graphene flakes were transferred to the silicon - silicon oxide substrates for the spectroscopic micro-Raman and scanning electron microscopy inspection. The analysis of the G peak, D, T+D and 2D bands in the Raman spectra under the 488-nm laser excitation indicate that the hig…
Owing to wide variety of applications of graphene, high-quality and economical way of synthesizing graphene is highly desirable. In this study, we report a cost effective and simple approach to production of high-quality graphene. Here the synthesis route is based on electrochemical exfoliation of graphite. Instead of using strong acids (which oxidise and damage the geometrical topology of graphene), we have used alkaline solution (KOH dissolved in water) as electrolyte. TEM analysis shows that as prepared graphene has 1-4 layers and large lateral size (up to ~18 micrometer). Raman analysis sh…
We introduce a novel modality in the CVD growth of graphene which combines the cold-wall and hot-wall reaction chambers. This hybrid mode preserves the advantages of a cold-wall chamber as the fast growth and low fuel consumption, but boosts the quality of the growth towards conventional CVD with hot-wall chambers. The synthesized graphene is uniform and monolayer. The electronic transport measurements shows great improvements in charge carrier mobility compared to graphene synthesized in a normal cold-wall reaction chamber. Our results promise the development of a fast and cost-efficient grow…
Atomically thin crystals have recently been the focus of attention in particular after the synthesis of graphene, a monolayer hexagonal crystal structure of carbon. In this novel material class the chemically derived graphenes have attracted tremendous interest. It was shown that although bulk graphite is a chemically inert material, the surface of single layer graphene is rather reactive against individual atoms. So far, synthesis of several graphene derivatives have been reported such as hydrogenated graphene "graphane" (CH), fluorographene (CF) and chlorographene (CCl). Moreover, the stabil…
A novel route for the synthesis of large area graphene by an indigenously built electron cyclotron resonance (ECR) plasma enhanced chemical vapor deposition (PECVD) setup has been reported in this work. A unique 2.45 GHz permanent magnet type ECR PECVD system has been designed and developed for the growth of various nano-structures and films. The apparatus has a unique advantage to synthesize large area graphene at much lower additional substrate heating than heat supplied by an external oven in conventional thermal CVD method. A major amount of heat is supplied here by ECR plasma. Polycrystal…
The growth of graphene on copper by atmospheric pressure chemical vapor deposition in a system free of pumping equipment is investigated. The emphasis is put on the necessity of hydrogen presence during graphene synthesis and cooling. In the absence of hydrogen during the growth step or cooling at slow rate, weak carbon coverage, consisting mostly of oxidized and amorphous carbon, is obtained on the copper catalyst. The oxidation originates from the inevitable occurrence of residual oxidizing impurities in the reactor's atmosphere. Graphene with appreciable coverage can be grown within the vac…
We synthesized centimeter-scale single- to few-layer graphene (FLG) films via chemical vapor deposition (CVD) on Ni foils. We demonstrates that the precipitation mechanism may not be the only important mechanism in the formation of graphene by CVD in Ni system, and that controlling the cooling rate in the CVD process may not be the appropriate way to control the thickness of graphene films. In addition, we are the first to demonstrate the transfer of centimeter-scale FLG from Ni foil to transparent flexible polyethylene terephthalate substrates via an efficient roll-to-roll process. Comparing …
High-kinetic energy impacts between inorganic surfaces and molecular beams seeded by organics represent a fundamental case study in materials science, most notably when they activate chemical-physical processes leading to nanocrystals growth. Here we demonstrate single-layer graphene synthesis on copper by C60 supersonic molecular beam (SuMBE) epitaxy at 645 °C, with the possibility of further reduction. Using a variety of electron spectroscopy and microscopy techniques, and first-principles simulations, we describe the chemical-physical mechanisms activated by SuMBE resulting in graphene grow…
The transfer-free synthesis of high-quality, large-area graphene on a given dielectric substrate, which is highly desirable for device applications, remains a significant challenge. In this paper, we report on a simple rapid thermal treatment method for the fast and direct growth of high-quality, large-scale monolayer graphene on a SiO2/Si substrate from solid carbon sources. The stack structure of solid carbon layer/copper film/SiO2 is adopted in the RTT process. The inserted copper film does not only act as an active catalyst for the carbon precursor but also serves as a "filter" that preven…
Germanium is emerging as the substrate of choice for the growth of graphene in CMOS-compatible processes. For future application in next generation devices the accurate control over the properties of high-quality graphene synthesized on Ge surfaces, such as number of layers and domain size, is of paramount importance. Here we investigate the role of the process gas flows on the CVD growth of graphene on Ge(100). The quality and morphology of the deposited material is assessed by using microRaman spectroscopy, x-ray photoemission spectroscopy, scanning electron and atomic force microscopies. We…
In this work we shed light on the early stage of the chemical vapor deposition of graphene on Ge(001) surfaces. By a combined use of microRaman and x-ray photoelectron spectroscopies, and scanning tunneling microscopy and spectroscopy, we were able to individuate a carbon precursor phase to graphene nucleation which coexists with small graphene domains. This precursor phase is made of C aggregates with different size, shape and local ordering which are not fully sp2 hybridized. In some atomic size regions these aggregates show a linear arrangement of atoms as well as the first signature of the…
Graphene has been attracting great interest because of its distinctive band structure and physical properties. Today, graphene is limited to small sizes because it is produced mostly by exfoliating graphite. We grew large-area graphene films of the order of centimeters on copper substrates by chemical vapor deposition using methane. The films are predominantly single layer graphene with a small percentage (less than 5%) of the area having few layers, and are continuous across copper surface steps and grain boundaries. The low solubility of carbon in copper appears to help make this growth proc…
Large scale synthesis of single layer graphene (SLG) by chemical vapor deposition (CVD) has received a lot of attention recently. However, CVD synthesis of AB stacked bi-layer graphene (BLG) is still a challenging work. Here we report synthesis of BLG homogeneously in large area by thermal CVD. The 2D Raman band of CVD BLG splits into four components, suggesting splitting of electronic bands due to strong interlayer coupling. The splitting of electronic bands in CVD BLG is further evidenced by the study of near infrared (NIR) absorption and carrier dynamics probed by transient absorption spect…
We developed means to produce wafer scale, high-quality graphene films as large as 3 inch wafer size on Ni and Cu films under ambient-pressure and transfer them onto arbitrary substrates through instantaneous etching of metal layers. We also demonstrated the applications of the large-area graphene films for the batch fabrication of field-effect transistor (FET) arrays and stretchable strain gauges showing extraordinary performances. Transistors showed the hole and electron mobilities of the device of 1,100 cm2/Vs and 550 cm2/Vs at drain bias of -0.75V, respectively. The piezo-resistance gauge …
Two-dimensional graphene exhibits many fascinating properties such as ballistic electronic conduction and quantum Hall effect at room temperature.1-4 Graphene doped electrochemically or through charge-transfer with electron-donor and -acceptor molecules,5-7 shows marked changes in electronic structure, with characteristic signatures in the Raman spectra.5-10 Substitutional doping, universally used in tuning properties of semiconductors, could be a powerful tool to control the electronic properties of graphene. Here, we present the structure and properties of boron and nitrogen doped graphenes,…
Nanosize pores can turn semimetallic graphene into a semiconductor and from being impermeable into the most efficient molecular sieve membrane. However, scaling the pores down to the nanometer, while fulfilling the tight structural constraints imposed by applications, represents an enormous challenge for present top-down strategies. Here we report a bottom-up method to synthesize nanoporous graphene comprising an ordered array of pores separated by ribbons, which can be tuned down to the one nanometer range. The size, density, morphology and chemical composition of the pores are defined with a…
We demonstrate that freeing a single-atom thick layer of hexagonal boron nitride (hbn) from tight chemical bonding to a Ni(111) thin film grown on a W(110) substrate can be achieved by intercalation of Au atoms into the interface. This process has been systematically investigated using angle-resolved photoemission spectroscopy, X-ray photoemission and absorption techniques. It has been demonstrated that the transition of the hbn layer from the "rigid" into the "quasi-freestanding" state is accompanied by a change of its lattice constant. Using chemical vapor deposition, graphene has been succe…
The substrate temperature required for synthesis of graphene in an arc discharge plasma was studied. It was shown that an increase of copper substrate temperature up to the melting point leads to an increase in the amount of graphene production and the quality of graphene sheets. Favorable range of substrate temperatures for arc-based graphene synthesis was determined, and it is in a relatively narrow range of about 1210-1340 K.
Here we demonstrate the selective bulk scale synthesis of delaminated graphene sheets by a proper choice of magnetic field modulating an electric-arc. An ultra-high purity glassy graphite anode was sublimated in an argon atmosphere. Carbon nanotubes, as well as graphene sheets were found inside the deposit formed on the cathode. Both the high purity carbon nanotubes as well as graphene sheets, with minimal structural defects, were synthesized separately by varying the strength and orientation of the external magnetic field generated by arrays of permanent magnets. The as-synthesized carbonaceo…
By exhibiting a measurable bandgap and exotic valley physics, atomically-thick tungsten disulfide (WS2) offers exciting prospects for optoelectronic applications. The synthesis of continuous WS2 films on other two-dimensional (2D) materials would greatly facilitate the implementation of novel all-2D photoactive devices. In this work we demonstrate the scalable growth of WS2 on graphene and hexagonal boron nitride (h-BN) via a chemical vapor deposition (CVD) approach. Spectroscopic and microscopic analysis reveal that the film is bilayer-thick, with local monolayer inclusions. Photoluminescence…
The challenge of synthesizing graphene nanoribbons (GNRs) with atomic precision is currently being pursued along a one-way road, based on the synthesis of adequate molecular precursors that react in predefined ways through self-assembly processes. The synthetic options for GNR generation would multiply by adding a new direction to this readily successful approach, especially if both of them can be combined. We show here how GNR synthesis can be guided by an adequately nanotemplated substrate instead of by the traditionally designed reactants. The structural atomic precision, unachievable to da…
Graphene nanoribbons have attracted attention for their novel electronic and spin transport properties1-6, and because nanoribbons less than 10 nm wide have a band gap that can be used to make field effect transistors. However, producing nanoribbons of very high quality, or in high volumes, remains a challenge. Here, we show that pristine few-layer nanoribbons can be produced by unzipping mildly gas-phase oxidized multiwalled carbon nanotube using mechanical sonication in an organic solvent. The nanoribbons exhibit very high quality, with smooth edges (as seen by high-resolution transmission e…
Graphene-based nanostructures exhibit a vast range of exciting electronic properties that are absent in extended graphene. For example, quantum confinement in carbon nanotubes and armchair graphene nanoribbons (AGNRs) leads to the opening of substantial electronic band gaps that are directly linked to their structural boundary conditions. Even more intriguing are nanostructures with zigzag edges, which are expected to host spin-polarized electronic edge states and can thus serve as key elements for graphene-based spintronics. The most prominent example is zigzag graphene nanoribbons (ZGNRs) fo…
Chemical Vapor Deposition (CVD) of graphene on copper is one of the most efficient technologies for producing high quality graphene for large areas. Nevertheless, still high pressures and big quantities of precursor gas are currently required. The objective of this work is to deposit graphene using the monolayer-formation-time concept (t) from the kinetic theory of gases, which leads to an economization of the precursor gas, a minimization of the process pressure and the time needed to grow a graphene monolayer. Our process has been designed taking into account the dependence of t on the press…
Graphene is a material with enormous potential for numerous applications. Therefore, significant efforts are dedicated to large-scale graphene production using a chemical vapor deposition (CVD) technique. In addition, research is directed at developing methods to incorporate graphene in established production technologies and process flows. In this paper, we present a brief review of available CVD methods for graphene synthesis. We also discuss scalable methods to transfer graphene onto desired substrates. Finally, we discuss potential applications that would benefit from a fully scaled, semic…
Cubic spinel lithium manganese oxide (LiMn2O4) has been able to attract a great deal of attention over the years as a promising cathode material for large scale lithium ion batteries. Here a facile hydrothermal route followed by solid state reaction is developed using as grown ultrafine alpha-MnO2 nanorods to prepare one dimensional LiMn2O4 with 10-50nm diameters. To enhance the cathodic property of these nanorods, a unique synthesis technique of heat treatment is developed to grow 2D graphene oxide sheet enveloping 1D LiMn2O4 as interconnected framework. This nanocomposite 3D porous cathode e…
Nanocomposite material proves to be the best candidate to match todays technological need as fascinating properties can be achieved by combining two or more nanomaterials. Among various nanomaterials, graphene is able to stand out far ahead of all others because of its novel structure and exclusive characteristics. In particular, graphene metal nanocomposites have attracted enormous interest for their prospective use in various fields, including electronics and electrical and energy related areas. However, for the utmost use of potential of graphene, it has to be homogenously embedded into met…
Simple, yet versatile, methods to functionalize graphene flakes with metal (oxide) nanoparticles are in demand, particularly for the development of advanced catalysts. Herein, based on light-induced electrochemistry, a laser-assisted, continuous, solution route for the simultaneous reduction and modification of graphene oxide with catalytic nanoparticles is reported. Electrochemical graphene oxide (EGO) is used as starting material and electron-hole pair source due to its low degree of oxidation, which imparts structural integrity and an ability to withstand photodegradation. Simply illuminati…
The production of large area interfaces and the use of scalable methods to build-up designed nanostructures generating advanced functional properties are of high interest for many materials science applications. Nevertheless, large area coverage remains a major problem for pristine graphene and here we present a hybrid, composite graphene-like material soluble in water, which can be exploited in many areas, such as energy storage, electrodes fabrication, selective membranes and biosensing. Graphene oxide (GO) was produced by the traditional Hummers method being further reduced in the presence …
Graphene has recently attracted a great deal of interest in both academia and industry because of its unique electronic and optical properties [1,2], as well as its chemical, thermal, and mechanical properties. The superb characteristics of graphene make this material one of the most promising candidates for various applications, such as ultrafast electronic circuits [1] and photodetectors [2], clean and renewable energy [3], and rapid single-molecule DNA sequencing [4,5]. The electronic properties of the graphene system rely heavily on the number of graphene layers [6] and effects on the coup…
An electrospun membrane for vascular stent coating made of 2-methacryloyloxyethyl phosphorylcholine and butyl methacrylate copolymer (MPC-co-BMA), also known as (PMB), reinforced with functionalized and nitrogen doped reduced graphene oxide (f-NrGO) is presented. This membrane due to the nitrogen doped reduced graphene oxide (NrGO) negative electric charge has the capacity to repeal low density lipoproteins (LDL), which under specific conditions are the main cause of atherosclerotic disease. The NrGO functionalization process is detailed, as it creates strong bonds between NrGO and PMB, avoidi…
Graphene intercalation materials are potentially promising for the implementation of the ultra-low power, excitonic-condensate-based Bilayer pseudoSpin Field-Effect Transistor (BiSFET) concept, as well as other novel device concepts requiring a graphene interlayer dielectric. Using density functional theory (DFT) we study the structural and electronic properties of bilayer graphene intercalated with iodine monochloride (ICl) and iodine monobromide (IBr). We determine the structural configuration of ICl and IBr graphene intercalation compounds (GICs). We also conduct an in-depth exploration of …
The synthesis of transition metals in a two-dimensional (2D) fashion has attracted growing attention for both fundamental and application-oriented investigations, such as 2D magnetism, nanoplasmonics and non-linear optics. However, the large-area synthesis of this class of materials in a single-layer form poses non-trivial difficulties. Here we present the synthesis of a large-area 2D gold layer, stabilized in between silicon carbide and monolayer (ML) graphene. We show that the 2D-Au ML is a semiconductor with the valence band maximum 50 meV below the Fermi level. The graphene and gold layers…
We systematically investigate the chemical vapor deposition growth of graphene on Ge(110) as a function of the deposition temperature close to the Ge melting point. By merging spectroscopic and morphological information, we find that the quality of graphene films depends critically on the growth temperature improving significantly by increasing this temperature in the 910-930 °C range. We correlate the abrupt improvement of the graphene quality to the formation of a quasi-liquid Ge surface occurring in the same temperature range, which determines increased atom diffusivity and sublimation rate…
Large-area ($\sim$cm$^2$) films of vertical heterostructures formed by alternating graphene and transition-metal dichalcogenide(TMD) alloys are obtained by wet chemical routes followed by a thermal treatment at low temperature (300 $^\circ$C). In particular, we synthesized stacked graphene and W$_x$Mo$_{1-x}$S$_2$ alloy phases that were used as hydrogen evolution catalysts. We observed a Tafel slope of 38.7 mV dec$^{-1}$ and 96 mV onset potential (at current density of 10 mA cm$^{-2}$) when the heterostructure alloy is annealed at 300 $^o$C. These results indicate that heterostructure formed b…
A high temperature for some catalytic reactions like synthesis of large area and high quality graphene is required. The mentioned graphene can be obtained by a chemical vapour deposition (CVD) process on copper foil at 800 1000. Here, we describe a room temperature synthesis method from different carbon sources for the first time, including acetylene, carbon dioxide and carbon monoxide, on copper foil by using a heuristic method which was inspired from the role of some electronic promoters in catalyst science. Promoters are substances that increase the catalytic activity, but they are not cata…
Rhombohedral-stacked few-layer graphene (FLG) has been receiving an ever-increasing attention owing to its peculiar electronic properties that could lead to enticing phenomena such as superconductivity and magnetic ordering. Up to now, experimental studies on such material have been mainly limited by the difficulty in isolating it in thickness exceeding 3 atomic layers with device-compatible size. In this work, rhombohedral graphene with thickness up to 9 layers and areas up to ~50 micrometers square is grown via chemical vapor deposition (CVD) on suspended Cu foils and transferred onto target…
As a viable candidate for an all-carbon post-CMOS electronics revolution, epitaxial graphene has attracted significant attention. To realize its application potential, reliable methods for fabricating large-area single-crystalline graphene domains are required. A new way to synthesize high quality epitaxial graphene, namely "face-to-face" method, has been reported in this paper. The structure and morphologies of the samples are characterized by low-energy electron diffraction, atomic force microscopy, angle-resolved photoemission spectroscopy and Raman spectroscopy. The grown samples show bett…
Graphene and carbon nanotubes (CNTs) share the same atomic structure of hexagonal carbon lattice. Yet, their synthesis differs in many aspects, including the shape and size of the catalyst. Here, we demonstrate a floating-catalyst chemical vapor deposition (FCCVD) technique for substrate-free, single-step growth of CNT-graphene heterostructures (CNT-G-H) using ethylene as a carbon source. The formation of CNT-G-H is directly evidenced by lattice-resolved (scanning) transmission electron microscopy (STEM) and electron diffraction experiments, corroborated by atomic force microscopy (AFM). Our e…
Bottom-up graphene nanoribbon (GNR) heterojunctions are nanoscale strips of graphene whose electronic structure abruptly changes across a covalently bonded interface. Their rational design offers opportunities for profound technological advancements enabled by their extraordinary structural and electronic properties. Thus far the most critical aspect of their synthesis, the control over sequence and position of heterojunctions along the length of a ribbon, has been plagued by randomness in monomer sequences emerging from step-growth copolymerization of distinct monomers. All bottom-up GNR hete…
The combination of the exciting properties of graphene with those of monolayer tungsten disulfide (WS2) makes this heterostack of great interest for electronic, optoelectronic and spintronic applications. The scalable synthesis of graphene/WS2 heterostructures on technologically attractive substrates like SiO2 would greatly facilitate the implementation of novel two-dimensional (2D) devices. In this work, we report the direct growth of monolayer WS2 via chemical vapor deposition (CVD) on single-crystal graphene arrays on SiO2. Remarkably, spectroscopic and microscopic characterization reveals …
Atomically thin graphite, known as graphene, has been a marvel in material science because of its exceptional properties, novel physics and promising applications. Atomically thin diamond, called diamane, has also attracted considerable scientific interest due to its potential physical and mechanical properties. However, until now there has been no reports of successful synthesis of a free-standing pristine diamane film. Here, we report the synthesis and electronic structure characterization of diamane. Electrical measurements, x-ray diffraction and theoretical simulations reveal that trilayer…
We report the synthesis of single and bi layer graphene films by low pressure chemical vapor deposition technique on Cu and Au substrates. The as grown films were characterized by transmission electron microscopy, scanning electron microscopy and Raman spectroscopy techniques. The large lateral area graphene deposited on Cu can easily be transferred on Si SiO2. In the case of Au substrate both the adsorption and diffusion-precipitation leads to the growth of graphene.
Graphene nanoflakes (GNFs) were synthesized by atmospheric pressure chemical vapour deposition of propane (C3H8) employing Ni (salen) powder without the introduction of a substrate. The graphitic nature of the GNFs was examined by an X-ray diffraction method. Scanning electron microscopy results revealed that GNFs were stacked on top of one another and had a high aspect ratio. Transmission electron microscopy studies suggested that the GNFs were made up of a number of crystalline graphene layers, some of which were even single crystalline as evident from the selected area diffraction pattern. …
Graphene- the wonder material has attracted a great deal of attention from varied fields of condensed matter physics, materials science and chemistry in recent times. Its 2D atomic layer structure and unique electronic band structure makes it attractive for many applications. Its high carrier mobility, high electrical and thermal conductivity make it an exciting material. However, its applicability cannot be effectively realised unless facile techniques to synthesize high quality, large area graphene are developed in a cost effective way. Besides that a great deal of effort is required to deve…
The spectrum of two-dimensional (2D) materials beyond graphene offers a remarkable platform to study new phenomena in condensed matter physics. Among these materials, layered hexagonal boron nitride (hBN), with its wide bandgap energy (~5.0-6.0 eV), has clearly established that 2D nitrides are key to advancing novel devices1. A gap, however, remains between the theoretical prediction of 2D nitrides beyond hBN and experimental realization of such structures. Here we demonstrate the synthesis of 2D gallium nitride (GaN) via a novel migration-enhanced encapsulated growth (MEEG) technique utilizin…
The adoption of graphene in electronics, optoelectronics and photonics is hindered by the difficulty in obtaining high quality material on technologically-relevant substrates, over wafer-scale sizes and with metal contamination levels compatible with industrial requirements. To date, the direct growth of graphene on insulating substrates has proved to be challenging, usually requiring metal-catalysts or yielding defective graphene. In this work, we demonstrate a metal-free approach implemented in commercially available reactors to obtain high-quality monolayer graphene on c-plane sapphire subs…
