Using atomistic computer simulations, we study how ion irradiation can be used to alter the morphology of a graphene monolayer by introducing defects of specific type, and to cut graphene sheets. Based on the results of our analytical potential molecular dynamics simulations, a kinetic Monte Carlo code is developed for modelling morphological changes in a graphene monolayer under irradiation at macroscopic time scales. Impacts of He, Ne, Ar, Kr, Xe and Ga ions with kinetic energies ranging from tens of eV to 10 MeV and angles of incidence between 0\circ and 88\circ are studied. Our results provide microscopic insights into the response of graphene to ion irradiation and can directly be used for the optimization of graphene cutting and patterning with focused ion beams.
We report nanoscale patterning of graphene using a helium ion microscope configured for lithography. Helium ion lithography is a direct-write lithography process, comparable to conventional focused ion beam patterning, with no resist or other material contacting the sample surface. In the present application, graphene samples on Si/SiO2 substrates are cut using helium ions, with computer controlled alignment, patterning, and exposure. Once suitable beam doses are determined, sharp edge profiles and clean etching are obtained, with little evident damage or doping to the sample. This technique p…
Basing on the molecular theory of graphene, the influence of the chemical modification of edge atoms of a graphene sheet is studied in terms of mechanochemical reactions. The mechanical behavior of graphene is shown to be not only highly anisotropic with respect to the direction of the load application, but greatly dependent on the chemical modification of the edges as well. A topological character of the graphene deformation is discussed.
Graphene modifications with oxygen or hydrogen are well known in contrast to carbon attachment to the graphene lattice. The chemical modification of graphene sheets with aromatic diazonium ions (carbon attachment) is analyzed by confocal Raman spectroscopy. The temporal and spatial evolution of surface adsorbed species allowed accurate tracking of the chemical reaction and identification of intermediates. The controlled transformation of sp2 to sp3 carbon proceeds in two separate steps. The presented derivatization is selective for single layer graphene and allows controlled transformation of …
Low-energy ion beam modification was proposed to create graphene on the top of the insulated diamond-like carbon films. In such low-temperature fabrication process the surface of the amorphous carbon could crystallize to graphene as a result of point defect creation and enhanced diffusion caused by the ion bombardment. In the experiment 130 eV argon ion irradiation was used. After the modification the resistivity of the sample surface drops. Raman spectra of the samples measured at 633 nm showed partial crystallization and were similar to the spectra of defected graphene. This result is very e…
Electronic decoupling of graphene from metallic and semiconducting substrates via intercalation of different species is one of the widely used approaches in studies of graphene. In the present work the modification of the electronic and magnetic properties of graphene on ferromagnetic Ni(111) layer via intercalation of halogen atoms (X = F, Cl, Br) is studied using the state-of-the-art density-functional theory approach. It is found that in all gr/X/Ni(111) intercalation systems a graphene layer is fully electronically decoupled from the ferromagnetic substrate; however, different kind (electr…
Electronic properties of the graphene layer sandwiched between two hexagonal boron nitride sheets have been studied using the first-principles calculations and the minimal tight-binding model. It is shown that for the ABC-stacked structure in the absence of external field the bands are linear in the vicinity of the Dirac points as in the case of single-layer graphene. For certain atomic configuration, the electric field effect allows opening of a band gap of over 230 meV. We believe that this mechanism of energy gap tuning could significantly improve the characteristics of graphene-based field…
We have carried out the systematic study of quantum capacitance (C$_Q$) in functionalized graphene. The functionlization of graphene has been done by doping with different aliphatic and aromatic molecules and their radicals. Using density functional theory calculations, we first analyze the electronic band structure of the functionalized graphene and subsequently obtained the quantum capacitance in each system. We observed that the quantum capacitance can be enhanced by doping aliphatic and aromatic molecules and their radicals on graphene sheet, especially radical functionalized graphene show…
We report combined first-principle and tight-binding (TB) calculations to simulate the effects of chemical edge modifications on structural and electronic properties. The C-C bond lengths and bond angles near the GNR edge have considerable changes when edge carbon atoms are bounded to different atoms. By introducing a phenomenological hopping parameter $t_{1}$ for nearest-neighboring hopping to represent various chemical edge modifications, we investigated the electronic structural changes of nanoribbons with different widths based on the tight-binding scheme. Theoretical results show that add…
Graphene has many unique properties which make it an attractive material for fundamental study as well as for potential applications. In this paper, we report the first experimental study of process-induced defects and stress in graphene using Raman spectroscopy and imaging. While defects lead to the observation of defect-related Raman bands, stress causes shift in phonon frequency. A compressive stress (as high as 2.1 GPa) was induced in graphene by depositing a 5 nm SiO2 followed by annealing, whereas a tensile stress (~ 0.7 GPa) was obtained by depositing a thin silicon capping layer. In th…
The unique thinness of two-dimensional materials enables control over chemical phenomena at their surfaces by means of various gating techniques. For example, gating methods based on field-effect-transistor configurations have been achieved. Here, we report a molecular gating approach that employs a local electric field generated by a polar self-assembled monolayer formed on a supporting substrate. By performing Raman scattering spectroscopy analyses with a proper data correction procedure, we found that molecular gating is effective for controlling solid phase photochemical reactions of graph…
We investigate the influence of SiO2, Au, Ag, Cu, and Pt substrates on the Raman spectrum of graphene. Experiments reveal particularly strong modifications to the intensity, position, width, and shape of the Raman signal of graphene on platinum, compared to that of suspended graphene. The modifications strongly depend on the relative orientation of the graphene and platinum lattices. These observations are theoretically investigated and shown to originate from hybridization of electronic states in graphene and d-orbitals in platinum. It is expected that, quite generally, hybridization between …
Controlled modification of graphene properties is essential for its proposed electronic applications. Here we describe a possibility of tuning electrical properties of graphene via electron beam irradiation. We show that by controlling the irradiation dose one can change the carrier mobility and increase the resistance at the minimum conduction point in the single layer graphene. The bilayer graphene is less susceptible to the electron beam irradiation. The modification of graphene properties via irradiation can be monitored and quantified by the changes in the disorder D peak in Raman spectru…
In order to harvest the many promising properties of graphene in (electronic) applications, a technique is required to cut, shape or sculpt the material on a nanoscale without damage to its atomic structure, as this drastically influences the electronic properties of the nanostructure. Here, we reveal a temperature-dependent self-repair mechanism allowing damage-free atomic-scale sculpting of graphene using a focused electron beam. We demonstrate that by sculpting at temperatures above 600 °C, an intrinsic self-repair mechanism keeps the graphene single-crystalline during cutting, even thought…
The chapter is devoted to chemical uniqueness of graphene. In view of molecular theory, the latter is a consequence of benzenoid packing of carbon atoms, based on three neighbors to each carbon atom leaving the atom fourth valence electron (the odd one) on its own. Due to rather large C-C distances, the odd electrons of graphene molecules are correlated whereupon the molecules are radicalized and molecular chemistry of graphene is the chemistry of dangling bonds. The chapter presents the description of the molecular-theory-dangling-bond view on graphene molecule hydrogenation and oxidation. Sp…
Graphene is an ultrathin material, which allows us to control surface phenomena by means of field-effect gating. Among various surface phenomena, photo-oxidation is known to be a facile method to largely control the electronic structure of graphene. In this study, gate controllability of photo-oxidation of graphene is thoroughly examined using a field-effect-transistor configuration. The presence of water molecules enhances gate controllability, which can be explained using water-oxygen co-adsorption picture. In addition, the photo-oxidation reaction evolves from the edge and proceeds towards …
The authors report micro-Raman investigation of changes in the single and bilayer graphene crystal lattice induced by the low and medium energy electron-beam irradiation (5 and 20 keV). It was found that the radiation exposures results in appearance of the strong disorder D band around 1345 1/cm indicating damage to the lattice. The D and G peak evolution with the increasing radiation dose follows the amorphization trajectory, which suggests graphene's transformation to the nanocrystalline, and then to amorphous form. The results have important implications for graphene characterization and de…
The role of defects in van der Waals heterostructures made of graphene and hexagonal boron nitride (h-BN) is studied by a combination of ab initio and model calculations. Despite the weak van der Waals interaction between layers, defects residing in h-BN, such as carbon impurities and antisite defects, reveal a hybridization with graphene p$_{\rm z}$ states, leading to midgap state formation. The induced midgap states modify the transport properties of graphene and can be reproduced by means of a simple effective tight-binding model. In contrast to carbon defects, it is found that oxygen defec…
Oxidation-resilient structural modifications in Nickel-functionalized 3D-graphene for hydrogen storage applications
Istituto Nanoscienze–CNR（意大利国家研究委员会纳米科学研究所）；NEST-Scuola Normale Superiore（新实验科学与技术学院-高等师范学校）；Department of Physical Science, Earth, and Environment, University of Siena（锡耶纳大学地球与环境物理科学系）；Institute of Sensor and Actuator Systems, TU Wien（维也纳工业大学传感器与致动器系统研究所）；CNR - Istituto Officina dei Materiali (IOM)（意大利国家研究委员会材料工厂研究所）
It has been shown that the first C layer on the SiC(0001)(2{\times}2)C surface already exhibits graphene-like electronic structure, with linear pi bands near the Dirac point. Indeed, the (2{\times}2)C reconstruction, with a Si adatom and C restatom structure, efficiently passivates the SiC(0001) surface thanks to an adatom/restatom charge transfer mechanism. Here, we study the effects of interface modifications on the graphene layer using density functional theory calculations. The modifications we consider are inspired from native interface defects observed by scanning tunneling microscopy. O…
BN Doping in the Realm of Two-Dimensional Fullerene Network for Unparalleled Structural, Electronic, Optical, and HER Advancements: A Cutting-Edge DFT Investigation
The possibility of modification of the local properties of hexagonal boron nitride (h-BN) by laser irradiation is investigated. Investigations conducted using both Raman spectroscopy and electrostatic force microscopy were performed. Laser light induced modifications are found to cause no structural changes. However, they have impact on Raman spectra and local charge state of the material. They are also shown to be stable in time and during electrical grounding of the sample. The mechanism of photoionization of deep defects present in h-BN is proposed to explain the observed phenomenon. The di…
We report on the on-surface synthesis of 7 armchair graphene nanoribbons (7-AGNRs) substituted with nitrile (CN) functional groups. The CN groups are attached to the GNR backbone by modifying the 7-AGNR precursor. While many of these groups survive the on-surface synthesis, the reaction process causes the cleavage of some CN from the ribbon backbone and the on-surface cycloisomerization of few nitriles onto pyridine rings. Scanning Tunneling Spectroscopy and Density Functional Theory reveal that CN groups behave as very efficient n-dopants, significantly downshifting the bands of the ribbon, a…
Plasma surface modification was used to fabricate graphene on the top of insulating diamond-like carbon films. It is shown that by a combination of pulsed argon plasma treatment and thermal annealing at 350\degreeC is possible to achieve partial crystallization of amorphous carbon to graphene. The observed Raman spectra are typical for defected graphene - splitted D- and G-peaks and a broad 2D-peak. This result is very encouraging and we hope that by improving this technology it will be possible to fabricate defect-free graphene, which can be used in electronics without transfer to other subst…
The Fermi velocity is one of the key concepts in the study of a material, as it bears information on a variety of fundamental properties. Upon increasing demand on the device applications, graphene is viewed as a prototypical system for engineering Fermi velocity. Indeed, several efforts have succeeded in modifying Fermi velocity by varying charge carrier concentration. Here we present a powerful but simple new way to engineer Fermi velocity while holding the charge carrier concentration constant. We find that when the environment embedding graphene is modified, the Fermi velocity of graphene …
Oxygen molecules are found to exhibit non-negligible reactivity with graphene under strong light irradiation in the presence of water. The reaction is triggered by the laser Raman spectroscopy measurement itself, and the D band (ca. 1340 cm-1) becomes larger as the laser irradiation is prolonged. The electronic transport properties of the graphene derivative are also investigated and both the electron and hole mobility are found to be reduced. These results are attributed to oxidation of graphene. This primitive modification method can be exploited to manipulate the structural and electronic p…
We demonstrated doping in 2D monolayer graphene via local electrical stressing. The doping, confirmed by the resistance-voltage transfer characteristics of the graphene system, is observed to continuously tunable from N-type to P-type as the electrical stressing level (voltage) increases. Two major physical mechanisms are proposed to interpret the observed phenomena: modifications of surface chemistry for N-type doping (at low-level stressing) and thermally-activated charge transfer from graphene to SiO2 substrate for P-type doping (at high-level stressing). The formation of P-N junction on 2D…
We report about investigations of time-dependent structural modifications in single crystal graphene due to laser irradiation even at moderate power levels of 1mW in a diffraction limited spot. The structural modifications have been characterized by in situ scanning confocal Raman spectroscopy, atomic force height microscopy and transport studies. The time evolution of the Raman spectrum reveals two different effects: on a short time scale, dopants, initially present on the flake, are removed. The longer time scale behavior points to a laser induced gradual local decomposition of single crysta…
The electrical transport properties of epitaxial graphene layers are correlated with the SiC surface morphology. In this study we show by atomic force microscopy and Raman measurements that the surface morphology and the structure of the epitaxial graphene layers change significantly when different pretreatment procedures are applied to nearly on-axis 6H-SiC(0001) substrates. It turns out that the often used hydrogen etching of the substrate is responsible for undesirable high macro steps evolving during graphene growth. A more advantageous type of sub-nanometer stepped graphene layers is obta…
We showed how a structural modification of graphene, which gives a carbon allotrope graphyne, can induce an energy gap at the K point of the Brillouin zone. Upon adsorption on metallic surfaces, the same mechanism is responsible for the further modification of the energy gap which occurs via the charge transfer mechanism. We performed the calculation based on the density functional theory with the novel non-local vdW-DF correlation of the adsorption of graphyne on Cu(111), Ni(111) and Co(0001) surfaces and showed the dependence of the gap change on the charge transfer in the system. The bindin…
In this paper we show how single layer graphene can be utilized to study swift heavy ion (SHI) modifications on various substrates. The samples were prepared by mechanical exfoliation of bulk graphite onto SrTiO$_3$, NaCl and Si(111), respectively. SHI irradiations were performed under glancing angles of incidence and the samples were analysed by means of atomic force microscopy in ambient conditions. We show that graphene can be used to check whether the irradiation was successful or not, to determine the nominal ion fluence and to locally mark SHI impacts. In case of samples prepared in situ…
In this work, the effect of the ion fluence-dependent defect formation on the modification of surface electronic and optical properties of graphene has been investigated. The chemical vapor deposited (CVD) graphene was irradiated with swift heavy ion (SHI) (70 MeV Si+5) beam at different fluence to study the defect formation mechanism and the role of it in modulating its surface electronic property such as work function. At low ion dose, acceptor doping via vacancy creation was observed; whereas dense electronic excitation dominated extended defects was realized at higher dose, which subsequen…
The light-like dispersion of graphene monolayer results in many novel electronic properties in it1, however, this gapless feature also limits the applications of graphene monolayer in digital electronics2. A rare working solution to generate a moderate bandgap in graphene monolayer is to cut it into one-dimensional (1D) nanometre-wide ribbons3-13. Here we show that a wide bandgap can be created in a unique 1D strained structure, i.e., graphene-nanoribbon-like (GNR-like) structure, of a continuous graphene sheet via strong interaction between graphene and the metal substrate, instead of cutting…
The separation of complex inner and outer contours of glass articles with curved surfaces using ultrashort pulsed lasers is reported. Single-pass, full-thickness modifications along the entire substrate are achieved using a processing optics that allows for beam shaping of non-diffracting beams and, additionally, for aberration compensation of phase distortions occurring at the curved interface. The glass articles finally separated by thermal stress or via selective etching meet the demands of the medical industry in terms of micro-debris, surface quality and processing speed.
The absence of a band gap in graphene restricts its straight forward application as a channel material in field effect transistors. In this letter, we report on a new approach to engineer a band gap in graphene field effect devices (FED) by controlled structural modification of the graphene channel itself. The conductance in the FEDs is switched between a conductive "on-state" to an insulating "off-state" with more than six orders of magnitude difference in conductance. Above a critical value of an electric field applied to the FED gate under certain environmental conditions, a chemical modifi…
Many of the proposed future applications of graphene require the controlled introduction of defects into its perfect lattice. Energetic ions provide one way of achieving this challenging goal. Single heavy ions with kinetic energies in the 100 MeV range will produce nanometer-sized defects on dielectric but generally not on crystalline metal surfaces. In a metal the ion-induced electronic excitations are efficiently dissipated by the conduction electrons before the transfer of energy to the lattice atoms sets in. Therefore, graphene is not expected to be irradiation sensitive beyond the creati…
The modification of single layer graphene due to intense, picoseconds near-infrared laser pulses is investigated. We monitor the stable changes introduced to graphene upon photoexcitation using Raman spectroscopy. We find that photoexcitation leads to both a local increase in hole doping and a reduction in compressive strain. Possible explanations for these effects, due to photo-induced oxygenation and photo-induced buckling of the graphene, are discussed.
We set up an evolutionary algorithm combined with density functional tight-binding (DFTB) calculations to investigate hydrogen adsorption on flat graphene and graphene monolayers curved over substrate steps. During the evolution, candidates for the new generations are created by adsorption of an additional hydrogen atom to the stable configurations of the previous generation, where a mutation mechanism is also incorporated. Afterwards a two-stage selection procedure is employed. Selected candidates act as the parents of the next generation. In curved graphene, the evolution follows a similar p…
We demonstrate high-resolution modification of suspended multi-layer graphene sheets by controlled exposure to the focused electron beam of a transmission electron microscope. We show that this technique can be used to realize, on timescales of a few seconds, a variety of features, including nanometer-scale pores, slits, and gaps that are stable and do not evolve over time. Despite the extreme thinness of the suspended graphene sheets, extensive removal of material to produce the desired feature geometries is found to not introduce long-range distortion of the suspended sheet structure.
An atomistic model based on the spin-restricted extended Huckel theory (EHT) is presented for simulating electronic structure and I-V characteristics of graphene devices. The model is applied to zigzag and armchair graphene nano-ribbons (GNR) with and without hydrogen passivation, as well as for bilayer graphene. Further calculations are presented for electric fields in the nano-ribbon width direction and in the bilayer direction to show electronic structure modification. Finally, the EHT Hamiltonian and NEGF (Nonequilibrium Green's function) formalism are used for a paramagnetic zigzag GNR to…
With the motivation of improving the performance and reliability of aggressively scaled nano-patterned graphene field-effect transistors, we present the first systematic experimental study on charge and current distribution in multilayer graphene field-effect transistors. We find a very particular thickness dependence for Ion, Ioff, and the Ion/Ioff ratio, and propose a resistor network model including screening and interlayer coupling to explain the experimental findings. In particular, our model does not invoke modification of the linear energy-band structure of graphene for the multilayer c…
We study the response of graphene to high-intensity 10^11-10^12 Wcm^-2, 50-femtosecond laser pulse excitation. We establish that graphene has a fairly high (~3\times10^12Wcm^-2) single-shot damage threshold. Above this threshold, a single laser pulse cleanly ablates graphene, leaving microscopically defined edges. Below this threshold, we observe laser-induced defect formation that leads to degradation of the lattice over multiple exposures. We identify the lattice modification processes through in-situ Raman microscopy. The effective lifetime of CVD graphene under femtosecond near-IR irradiat…
Graphene's linear dispersion relation and the attendant implications for bipolar electronics applications have motivated a range of experimental efforts aimed at producing p-n junctions in graphene. Here we report electrical transport measurements of graphene p-n junctions formed via simple modifications to a PbZr$_{0.2}$Ti$_{0.8}$O$_3$ substrate, combined with a self-assembled layer of ambient environmental dopants. We show that the substrate configuration controls the local doping region, and that the p-n junction behavior can be controlled with a single gate. Finally, we show that the ferro…
