The ability to tune the thermal resistance of carbon nanotube mechanical supports from insulating to conducting could permit the next generation of thermal management devices. Here, we demonstrate fabrication techniques for carbon nanotube supports that realize either weak or strong thermal coupling, selectively. Direct imaging by in-situ electron thermal microscopy shows that the thermal contact resistance of a nanotube weakly-coupled to its support is greater than 250 K*m/W and that this value can be reduced to 4.2(+5.6/-2.1) K*m/W by imbedding the nanotube in metal contacts.
Quantum transport properties of intermolecular nanotube contacts are investigated. We find that atomic structure in the contact region plays important roles and resistance of contacts varies strongly with geometry and nanotube chirality. Nanotube end-end contacts have low resistance and show negative differential resistance (NDR) behavior. Contact resistance can be dramatically decreased by exerting small pressure/force between the tubes if the contact is commensurate. Significant variation and nonlinearity of contact resistance may lead to new device applications.
We have studied the resistance of single-wall carbon nanotubes measured in a four-point configuration with noninvasive voltage electrodes. The voltage drop is detected using multiwalled carbon nanotubes while the current is injected through nanofabricated Au electrodes. The resistance at room temperature is shown to be linear with the length as expected for a classical resistor. This changes at cryogenic temperature; the four-point resistance then depends on the resistance at the Au-tube interfaces and can even become negative due to quantum-interference effects.
We theoretically investigate the electro-mechanics of a Suspended Carbon Nanotube with a Deflection Sensitive Resistance subjected to a homogeneous Magnetic Field and a constant Voltage Bias. We show that, (with the exception of a singular case), for a sufficiently high magnetic field the time-independent state of charge transport through the nanotube becomes unstable to selfexcitations of the mechanical vibration accompanied by oscialltions in the voltage drop and current across the nanotube.
Capillary and van der Waals forces cause nanotubes to deform or even collapse under metal contacts. Using ab-initio bandstructure calculations, we find that these deformations reduce the bandgap by as much as 30\%, while fully collapsed nanotubes become metallic. Moreover degeneracy lifting, due to the broken axial symmetry and wavefunctions mismatch between the fully collapsed and the round portions of a CNT, leads to a three times higher contact resistance. The latter we demonstrate by contact resistance calculations within the tight-binding approach.
The features of the $IV$ characteristics of metallic carbon nanotubes (m-NTs) in different experimental setups are studied using semi-classical Boltzmann transport equation together with the heat dissipation equation to account for significant thermal effects at high electric bias. Our model predicts that the shape of the m-NT characteristics is basically controlled by heat removal mechanisms. In particular we show that the onset of negative differential resistance in free standing nanotubes finds its origins in strong transport nonlinearities associated with poor heat removal unlike in substr…
We investigate the response of multi-walled carbon nanotubes to mechanical strain applied with an Atomic Force Microscope (AFM) probe. We find that in some samples, changes in the contact resistance dominate the measured resistance change. In others, strain large enough to fracture the tube can be applied without a significant change in the contact resistance. In this case we observe that enough force is applied to break the tube without any change in resistance until the tube fails. We have also manipulated the ends of the broken tube back in contact with each other, re-establishing a finite …
We present quantitative predictions of the performance of nanotubes and nanowires as antennas, including the radiation resistance, the input reactance and resistance, and antenna efficiency, as a function of frequency and nanotube length. Particular attention is paid to the quantum capacitance and kinetic inductance. In so doing, we also develop a circuit model for a transmission line made of two parallel nanotubes, which has applications for nano-interconnect technology.
We show that a multi-walled carbon nanotube film can be used as the sensing element of a low-cost sensor for the alcoholic concentration in liquid solutions. To this purpose, we investigate the electrical resistance of the film as a function of the isopropanol concentration in a water solution. The analysis reveals a growing resistance with increasing isopropanol concentration and a fast response. The sensing element is re-usable as the initial resistance value is restored once the solution has evaporated. The electrical resistance increases linearly when the multi-walled carbon nanotube film …
We investigate the coupling between individual tubes in a rope of single-wall carbon nanotubes using four probe resistance measurements. By introducing defects through the controlled sputtering of the rope we generate a strong non-monotonic temperature dependence of the four terminal resistance. This behavior reflects the interplay between localization in the intentionally damaged tubes and coupling to undamaged tubes in the same rope. Using a simple model we obtain the coherence length and the coupling resistance. The coupling mechanism is argued to involve direct tunneling between tubes.
Several data sets of electrical breakdown in air of single-wall carbon nanotubes (SWNTs) on insulating substrates are collected and analyzed. A universal scaling of the Joule breakdown power with nanotube length is found, which appears independent of the insulating substrates used or their thickness. This suggests the thermal resistances at the interface between SWNT and insulator, and between SWNT and electrodes, govern heat sinking from the nanotube. Analytical models for the breakdown power scaling are presented, providing an intuitive, physical understanding of the breakdown process. The e…
An oscillatory dependence of the drain current on the drain voltage is found in a nanostructure consisting of two crossing semiconductor carbon nanotubes that are suspended over a dielectric trench, which is backed by a doped silicon substrate that acts as a gate. Alternating positive and negative differential resistance regions are generated as a function of the drain source values and can be slightly shifted by the gate voltage. Moreover, the negative differential resistance is retrieved in a large bandwidth, of up to 100 MHz, when the structure is excited with ac signals.
We present an experimental investigation on the scaling of resistance in individual single walled carbon nanotube devices with channel lengths that vary four orders of magnitude on the same sample. The electron mean free path is obtained from the linear scaling of resistance with length at various temperatures. The low temperature mean free path is determined by impurity scattering, while at high temperature the mean free path decreases with increasing temperature, indicating that it is limited by electron-phonon scattering. An unusually long mean free path at room temperature has been experim…
We report measurements on ropes of Single Walled Carbon Nanotubes (SWNT) in low-resistance contact to non-superconducting (normal) metallic pads, at low voltage and at temperatures down to 70 mK. In one sample, we find a two order of magnitude resistance drop below 0.55 K, which is destroyed by a magnetic field of the order of 1T, or by a d.c. current greater than 2.5 microA. These features strongly suggest the existence of superconductivity in ropes of SWNT.
Flexible, free-standing transparent conducting electrodes (TCEs) with simultaneously tunable transmittances up to 98% and sheet resistances down to 11 Ω/sq were prepared by a facile spray-coating method of silver nanowires (AgNWs) onto dry-spun multiwall carbon nanotube (MWNT) aerogels. Counterintuitively, the transmittance of the hybrid electrodes can be increased as the mass density of AgNWs within the MWNT aerogels increase, however, the final achievable transmittance depends on the initial transparency of the MWNT aerogels. At the same time, a strong decrease in sheet resistance is obtaine…
We calculate the intershell resistance R_{21} in a multiwall carbon nanotube as a function of temperature T and Fermi level (e.g. a gate voltage), varying the chirality of the inner and outer tubes. This is done in a so-called Coulomb drag setup, where a current I_1 in one shell induces a voltage drop V_2 in another shell by the screened Coulomb interaction between the shells neglecting the intershell tunnelling. We provide benchmark results for R_{21}=V_2/I_1 within the Fermi liquid theory using Boltzmann equations. The band structure gives rise to strongly chirality dependent suppression eff…
Vertically aligned ZnO nanotube arrays fabricated on an ITO substrate are found to exhibit strong persistent photoconductivity (PPC) effect and electrically driven conductance switching behavior, though the latter shows a gradual decay from high conductance state to a low conductance state. Unlike the electrical switching, the PPC cannot be reset or reversed by an electrical pulse. Excitation wavelength dependent conductance measurement indicates the presence of the defect localized states (DLS) ~ 240meV above the valence band edge, in support of the hypothesis that the doubly ionization of th…
We have calculated the effects of structural distortions of armchair carbon nanotubes on their electrical transport properties. We found that the bending of the nanotubes decreases their transmission function in certain energy ranges and leads to an increased electrical resistance. Electronic structure calculations show that these energy ranges contain localized states with significant $σ$-$π$ hybridization resulting from the increased curvature produced by bending. Our calculations of the contact resistance show that the large contact resistances observed for SWNTs are likely due to the weak …
We consider the conductance of a quantum tube connected to a metallic contact. The number of angular momentum states that the tube can support depends on the strength of the radial confinement. We calculate the transmission coefficients which yield the conductance via the Landauer formula. We relate our results to armchair carbon nanotubes embedded in a metal. For Al and Au contacts and tubes with a realistic radial confinement we find that the transmission can be close to unity corresponding to a contact resistance close to h/2e^2 per band at the Fermi level in the carbon nanotube.
We simulate quantum transport between a graphene nanoribbon (GNR) and a single-walled carbon nanotube (CNT) where electrons traverse vacuum gap between them. The GNR covers CNT over a nanoscale region while their relative rotation is 90 degrees, thereby forming a four-terminal crossbar where the bias voltage is applied between CNT and GNR terminals. The CNT and GNR are chosen as either semiconducting (s) or metallic (m) based on whether their two-terminal conductance exhibits a gap as a function of the Fermi energy or not, respectively. We find nonlinear current-voltage (I-V) characteristics i…
We report on electrical spin injection measurements on MWNTs . We use a ferromagnetic alloy Pd$_{1-x}$Ni$_{x}$ with x $\approx$ 0.7 which allows to obtain devices with resistances as low as 5.6 $kΩ$ at 300 $K$. The yield of device resistances below 100 $kΩ$, at 300 $K$, is around 50%. We measure at 2 $K$ a hysteretic magneto-resistance due to the magnetization reversal of the ferromagnetic leads. The relative difference between the resistance in the antiparallel (AP) orientation and the parallel (P) orientation is about 2%.
We report equilibrium electric resistance R and tunneling spectroscopy dI/dV measurements obtained on single multiwall nanotubes contacted by four metallic Au fingers from above. At low temperature quantum interference phenomena dominate the magnetoresistance. The phase-coherence and elastic-scattering lengths are deduced. Because the latter is of order of the circumference of the nanotubes, transport is quasi-ballistic. This result is supported by a dI/dV spectrum which is in good agreement with the density-of-states (DOS) due to the one-dimensional subbands expected for a perfect single-wall…
Using low-resistance electrical contacts, we have measured the intrinsic high-field transport properties of metallic single-wall carbon nanotubes. Individual nanotubes appear to be able to carry currents with a density exceeding 10^9 A/cm^2. As the bias voltage is increased, the conductance drops dramatically due to scattering of electrons. We show that the current-voltage characteristics can be explained by considering optical or zone-boundary phonon emission as the dominant scattering mechanism at high field.
The electrical and optical response of a field-effect device comprising a network of semiconductor-enriched single-wall carbon nanotubes, gated with sodium chloride solution is investigated. Field-effect is demonstrated in a device that uses facile fabrication techniques along with a small-ion as the gate electrolyte - and this is accomplished as a result of the semiconductor enhancement of the tubes. The optical transparency and electrical resistance of the device are modulated with gate voltage. A time-response study of the modulation of optical transparency and electrical resistance upon ap…
Spatially-resolved Raman spectra of individual pristine suspended carbon nanotubes are observed under electrical heating. The Raman G+ and G- bands show unequal temperature profiles. The preferential heating is more pronounced in short nanotubes (2 um) than in long nanotubes (5 um). These results are understood in terms of the decay and thermalization of non-equilibrium phonons, revealing the mechanism of thermal transport in these devices. The measurements also enable a direct estimate of thermal contact resistances and the spatial variation of thermal conductivity.
At any metal-carbon nanotube interface there is charge transfer and the induced interfacial field determines the position of the carbon nanotube band structure relative to the metal Fermi-level. In the case of a single-wall carbon nanotube (SWNT) supported on a gold substrate, we show that the charge transfers induce a local electrostatic potential perturbation which gives rise to the observed Fermi-level shift in scanning tunneling spectroscopy (STS) measurements. We also discuss the relevance of this study to recent experiments on carbon nanotube transistors and argue that the Fermi-level al…
We present first-principles calculations of quantum transport which show that the resistance of metallic carbon nanotubes can be changed dramatically with homogeneous transverse electric fields if the nanotubes have impurities or defects. The change of the resistance is predicted to range over more than two orders of magnitude with experimentally attainable electric fields. This novel property has its origin that backscattering of conduction electrons by impurities or defects in the nanotubes is strongly dependent on the strength and/or direction of the applied electric fields. We expect this …
Films composed of nanotube networks have their conductivities regulated by the junction resistances formed between tubes. Conductivity values are enhanced by lower junction resistances but should reach a maximum that is limited by the network morphology. By considering ideal ballistic-like contacts between nanotubes we use the Kubo formalism to calculate the upper bound for the conductivity of such films and show how it depends on the nanotube concentration as well as on their aspect ratio. Highest measured conductivities reported so far are approaching this limiting value, suggesting that fur…
We have altered the superconductivity of a suspended rope of single walled carbon nanotubes, by coating it with organic polymers. Upon coating, the normal state resistance of the rope changes by less than 20 percent. But superconductivity, which on the bare rope shows up as a substantial resistance decrease below 300 mK, is gradualy suppressed. We correlate this to the suppression of radial breathing modes, measured with Raman Spectroscopy on suspended Single and Double-walled carbon nanotubes. This points to the breathing phonon modes as being responsible for superconductivity in carbon nanot…
We have measured Coulomb drag between an individual single-walled carbon nanotube (SWNT) as a one-dimensional (1D) conductor and the two-dimensional (2D) conductor monolayer graphene, separated by a few-atom-thick boron nitride layer. The graphene carrier density is tuned across the charge neutrality point (CNP) by a gate, while the SWNT remains degenerate. At high temperatures, the drag resistance changes sign across the CNP, as expected for momentum transfer from drive to drag layer, and exhibits layer exchange Onsager reciprocity. We find that layer reciprocity is broken near the graphene C…
We characterize the energy loss of the non-equilibrium electron system in individual metallic single-walled carbon nanotubes at low temperature. Using Johnson noise thermometry, we demonstrate that, for a nanotube with ohmic contacts, the dc resistance at finite bias current directly reflects the average electron temperature. This enables a straightforward determination of the thermal conductance associated with cooling of the nanotube electron system. In analyzing the temperature- and length-dependence of the thermal conductance, we consider contributions from acoustic phonon emission, optica…
We report on the temperature dependence of the intrinsic resistance of long individual disordered single-wall carbon nanotubes. The resistance grows dramatically as the temperature is reduced, and the functional form is consistent with an activated behavior. These results are described by Coulomb blockade along a series of quantum dots. We occasionally observe a kink in the activated behavior that reflects the change of the activation energy as the temperature range is changed. This is attributed to charge hopping events between non-adjacent quantum dots, which is possible through cotunneling …
We report superconducting resistive transition characteristics for array(s) of coupled 4-Angstrom single wall carbon nanotubes embedded in aluminophosphate-five (AFI) zeolite. The transition was observed to initiate at 15K with a slow resistance decrease switching to a sharp, order of magnitude drop between 7.5-6.0K. The transition has strong (anisotropic) magnetic field dependence. Differential resistance versus current (voltage) measurements indicate that the establishment of coherence proceeds in stages as the temperature is lowered below 15K. In particular, the sharp resistance drop and it…
We demonstrate a "bottom up" approach to the computational design of a multifunctional chemical sensor. General techniques are employed for describing the adsorption coverage and resistance properties of the sensor based on density functional theory (DFT) and non-equilibrium Green's function methodologies (NEGF), respectively. Specifically, we show how Ni and Cu doped metallic (6,6) single-walled carbon nanotubes (SWNTs) may work as effective multifunctional sensors for both CO and NH3.
We report associated high resolution transmission electron microscopy (HRTEM) and transport measurements on a series of isolated multiwalled carbon nanotubes. HRTEM observations, by revealing relevant structural features of the tubes, shed some light on the variety of observed transport behaviors, from semiconducting to quasi-metallic type. Non Ohmic behavior is observed for certain samples which exhibit "bamboo like" structural defects. The resistance of the most conducting sample, measured down to 20 mK, exhibits a pronounced maximum at 0.6 K and strong positive magnetoresistance.
We explore the electric-field effect of carbon nanotubes (NTs) in electrolytes. Due to the large gate capacitance, Fermi energy shifts of order +/- 1 V can be induced, enabling to tune NTs from p to n-type. Consequently, large resistance changes are measured. At zero gate voltage the NTs are hole doped in air with E_F ? 0.3-0.5 eV, corresponding to a doping level of ? 10^{13} cm^{-2}. Hole-doping increases in the electrolyte. This hole doping (oxidation) is most likely caused by the adsorption of oxygen in air and cations in the electrolyte.
The measured electric resistance of carbon nanotubes wrapped with DNA molecules depends strongly on the spin of the injected electrons. Motivated by these experiments, we study the effect of helix-shaped potentials on the electronic spectrum of carbon nanotubes. We find that in combination with the curvature-induced spin-orbit coupling inherent to nanotubes, such a perturbation opens helicity-dependent gaps. Within these partial gaps, left-moving electrons carry a fixed spin-projection that is reversed for right-moving electrons, and the probability of electrons to transfer through the nanotub…
We characterize the terahertz detection mechanism in antenna-coupled metallic single-walled carbon nanotubes. At low temperature, 4.2 K, a peak in the low-frequency differential resistance is observed at zero bias current due to non-Ohmic contacts. This electrical contact nonlinearity gives rise to the measured terahertz response. By modeling each nanotube contact as a nonlinear resistor in parallel with a capacitor, we determine an upper bound for the value of the contact capacitance that is smaller than previous experimental estimates. The small magnitude of this contact capacitance has favo…
We present a data-calibrated compact model of carbon nanotube (CNT) field-effect transistors (CNFETs) including contact resistance, direct source-to-drain and band-to-band tunneling currents. The model captures the effects of dimensional scaling and performance degradations due to parasitic effects and is used to study the trade-offs between the drive current and leakage current of CNFETs according to the selection of CNT diameter, CNT density, contact length, and gate length for a target contacted gate pitch. We describe a co-optimization study of CNFET device parameters near the limits of sc…
We measure the resistance and frequency-dependent gate capacitance of carbon nanotube (CNT) thin films in ambient, vacuum, and under low-pressure (10E-6 torr) analyte environments. We model the CNT film as an RC transmission line and show that changes in the measured capacitance as a function of gate bias and analyte pressure are consistent with changes in the transmission line impedance due to changes in the CNT film resistivity alone; the electrostatic gate capacitance of the CNT film does not depend on gate voltage or chemical analyte adsorption. However, the CNT film resistance is enormous…
We have measured the scattering strength of charged impurities on a semiconducting single-walled carbon nanotube with known chirality. The resistivity of the nanotube is measured as a function of the density of adsorbed potassium atoms, enabling the determination of the resistance added by an individual potassium atom. Holes are scattered 37 times more efficiently than electrons by an adsorbed potassium atom. The determined scattering strength is used to reveal the spatial extent and depth of the scattering potential for potassium, a model Coulomb adsorbate. Our result represents an essential …
We present measurements of tunneling magneto-resistance (TMR) in single-wall carbon nanotubes attached to ferromagnetic contacts in the Coulomb blockade regime. Strong variations of the TMR with gate voltage over a range of four conductance resonances, including a peculiar double-dip signature, are observed. The data is compared to calculations in the "dressed second order" (DSO) framework. In this non-perturbative theory, conductance peak positions and linewidths are affected by charge fluctuations incorporating the properties of the carbon nanotube quantum dot and the ferromagnetic leads. Th…
Electron spin resonance (ESR) investigation of graphene nanoribbons (GNRs) prepared through longitudinal unzipping of multiwalled carbon nanotubes (MWCNTs) indicates the presence of C-related dangling bond centers, exhibiting paramagnetic features. ESR signal broadening from pristine or oxidized graphene nanoribbons (OGNRs) is explained in terms of unresolved hyperfine structure, and in the case of reduced GNRs (RGNRs), the broadening of ESR signal can be due to enhancement in conductivity upon reduction. The spin dynamics observed from ESR linewidth-temperature data reflect a variable range h…
Single walled carbon nanotubes (SWNT) have displayed a wealth of quantum transport phenomena thus far. Defect free, unperturbed SWNTs with wellbehaved or tunable metal contacts are important to probing the intrinsic electrical properties of nanotubes. Meeting these conditions experimentally is nontrivial due to numerous disorder and randomizing factors. Here we show that ~ 1 um long fully suspended SWNTs grown-in-place between metal contacts afford SWNT devices exhibiting well-defined characteristics over much wider energy ranges than nanotubes pinned on substrates. Various low temperature tra…
We use computational screening to systematically investigate the use of transition metal doped carbon nanotubes for chemical gas sensing. For a set of relevant target molecules (CO, NH3, H2S) and the main components of air (N2, O2, H2O), we calculate the binding energy and change in conductance upon adsorption on a metal atom occupying a vacancy of a (6,6) carbon nanotube. Based on these descriptors, we identify the most promising dopant candidates for detection of a given target molecule. From the fractional coverage of the metal sites in thermal equilibrium with air, we estimate the change i…
We investigate the quantum transport through a single-wall carbon nanotube connected to leads in the presence of an external radiation field. We analyze the conductance spectrum as a function of the frequency and strength of the field. We found that above a critical value of the field intensity, an enhancement of the conductance, or suppressed resistance, as a function of the field strength occurs. The conductance increases displaying oscillations which amplitude shows a strong dependence on the field frequency. For low radiation energies in comparison to the lead-CNT coupling energies, the os…
We use electrostatic force microscopy and scanned gate microscopy to probe the conducting properties of carbon nanotubes at room temperature. Multi-walled carbon nanotubes are shown to be diffusive conductors, while metallic single-walled carbon nanotubes are ballistic conductors over micron lengths. Semiconducting single-walled carbon nanotubes are shown to have a series of large barriers to conduction along their length. These measurements are also used to probe the contact resistance and locate breaks in carbon nanotube circuits.
Molybdenum disulfide nanoribbons and nanotubes are quasi-1D semiconductors with strong spin-orbit interaction, a nanomaterial highly promising for quantum electronic applications. Here, it is demonstrated that a bismuth semimetal layer between the contact metal and this nanomaterial strongly improves the properties of the contacts. Two-point resistances on the order of 100k$Ω$ are observed at room temperature. At cryogenic temperature, Coulomb blockade is visible. The resulting stability diagrams indicate a marked absence of trap states at the contacts and the corresponding disorder, compared …
We discuss magnetotransport measurements on individual single-wall carbon nanotubes with low contact resistance, performed as a function of temperature and gate voltage. We find that the application of a magnetic field perpendicular to the tube axis results in a large magnetoconductance of the order of e^2/h at low temperature. We demonstrate that this magnetoconductance consists of a sample-specific and of an ensemble-averaged contribution, both of which decrease with increasing temperature. The observed behavior resembles very closely the behavior of more conventional multi-channel mesoscopi…
We report ultra-high density assembly of aligned single walled carbon nanotubes (SWNTs) two dimensional arrays via ac dielectrophoresis using high quality surfactant free and stable SWNT solutions. After optimization of frequency and trapping time, we can reproducibly control the linear density of the SWNT between prefabricated electrodes from 0.5 SWNT/\mum to more than 30 SWNT /\mum by tuning the concentration of the nanotubes in the solution. Our maximum density of 30 SWNT/\mum is the highest for aligned arrays via any solution processing technique reported so far. Further increase of SWNT c…
In this Letter we demonstrate that Permalloy (Py), a widely used Ni/Fe alloy, forms contacts to carbon nanotubes (CNTs) that meet the requirements for the injection and detection of spin-polarized currents in carbon-based spintronic devices. We establish the material quality and magnetization properties of Py strips in the shape of suitable electrical contacts and find a sharp magnetization switching tunable by geometry in the anisotropic magnetoresistance (AMR) of a single strip at cryogenic temperatures. In addition, we show that Py contacts couple strongly to CNTs, comparable to Pd contacts…
Electron scattering rates in metallic single-walled carbon nanotubes are studied using an atomic force microscope as an electrical probe. From the scaling of the resistance of the same nanotube with length in the low and high bias regimes, the mean free paths for both regimes are inferred. The observed scattering rates are consistent with calculations for acoustic phonon scattering at low biases and zone boundary/optical phonon scattering at high biases.
We report low temperature transport measurements on suspended single walled carbon nanotubes (both individual tubes and ropes). The technique we have developed, where tubes are soldered on low resistive metallic contacts across a slit, enables a good characterization of the samples by transmission electron microscopy. It is possible to obtain individual tubes with a room temperature resistance smaller than 40 kOhms, which remain metallic down to very low temperatures. When the contact pads are superconducting, nanotubes exhibit proximity induced superconductivity with surprisingly large values…
We report the observation of Peierls-type metal-insulator transition in carbon nanostructures formed by chemical vapor deposition inside the pore network of the ZSM-5 zeolite. The Raman spectrum of this nanocarbon@ZSM-5 indicates a clear signature of the radial breathing mode (RBM) for (3,0) carbon nanotubes that can constitute the carbon network segments. Electrical transport measurements on multiple few-micron-sized nanocarbon@ZSM-5 crystals showed metallic temperature of resistance dependence down to 30 K, at which point the resistance exhibited a sharp upturn that is accompanied by the ope…
Carbon nanotubes (CNT) belong to the most promising new materials which can in the near future revolutionize the conventional electronics. When sandwiched between ferromagnetic electrodes, the CNT behaves like a spacer in conventional spin-valves, leading quite often to a considerable giant magneto-resistance effect (GMR). This paper is devoted to reviewing some topics related to electron correlations in CNT. The main attention however is directed to the following effects essential for electron transport through nanotubes: (i) nanotube/electrode coupling and (ii) inter-tube interactions.It is …
We use infrared thermometry of carbon nanotube network (CNN) transistors and find the formation of distinct hot spots during operation. However, the average CNN temperature at breakdown is significantly lower than expected from the breakdown of individual nanotubes, suggesting extremely high regions of power dissipation at the nanotube junctions. Statistical analysis and comparison with a thermal model allow the extraction of the average tube-tube junction thermal resistance, ~4.4x10^11 K/W (thermal conductance ~2.27 pW/K). This indicates that nanotube junctions have a much greater impact on C…
We describe the electro-thermal transport in metallic carbon nanotubes (m-CNTs) by a semi-classical approach that takes into account the high-field dynamical interdependence between charge carrier and phonon populations. Our model is based on the self-consistent solution of the Boltzmann transport equation and the heat equation mediated by a phonon rate equation that accounts for the onset of non-equilibrium (optical) phonons in the high-field regime. Given the metallic nature of the nanostructures, a key ingredient of the model is the assumption of local thermalization of charge carriers. Our…
We demonstrate assembly of solution processed semiconducting enriched (99%) single walled carbon nanotubes (s-SWNT) in an array with varying linear density via ac-dielectrophoresis and investigate detailed electronic transport properties of the fabricated devices. We show that (i) the quality of the alignment varies with frequency of the applied voltage and that (ii) by varying the frequency and concentration of the solution, we can control the linear density of the s-SWNTs in the array from 1/μm to 25 /μm. The maximum linear density of 25 s-SWNT /\mum reported here is the highest for any alig…
