Dielectric nano-swithes made of the materials that exhibit piezoelectric and/or flexoelectric properties with significant electro-mechanical coupling are considered. In this case, a nonuniform strain field may locally break inversion symmetry and induce polarization even in nonpiezoelectrics. At reducing dimensions to the nanoscale, the flexoelectric effect demonstrates the nonlocality of the dielectric materials and plays more significant role than piezoelectric effect. The flexoelectric effect is included into consideration via additional term coupling strain gradient and polarization in the electric enthalpy density. The equations of motion of the improved Euler-Bernoulli and Timoshenko beam models, and 2-D plate theory have been obtained.
We investigate the role of quantum effects (e.g. zero-point energy fluctuations) in the physics of nanotube- and nanowire-based electromechanical sensors as discussed in a recent article [Postma et al., Appl. Phys. Lett. 86, 223105 (2005)]. Employing the quantum fluctuation-dissipation theorem we find that these effects pose additional limits on the dynamic range of nanomechanical resonators.
Thermal management is an important challenge in modern electronics, avionics, automotive, and energy storage systems. While passive thermal solutions (like heat sinks or heat spreaders) are often used, actively modulating heat flow (e.g. via thermal switches or diodes) would offer additional degrees of control over the management of thermal transients and system reliability. Here we report the first thermal switch based on a flexible, collapsible graphene membrane, with low operating voltage, < 2 V. We also employ active-mode scanning thermal microscopy (SThM) to measure the device behavior an…
Nanoscale enables a broad range of electromechanical coupling mechanisms that are forbidden or negligible in the materials. We conduct a theoretical study of the electromechanical response of thin paraelectric films with mobile vacancies (or ions) paradigmatic for capacitor-type measurements in X-ray scattering, piezoresponse force microscopy (PFM), and electrochemical strain microscopy (ESM). Using quantum paraelectric SrTiO3 film as a model material with well known electromechanical, electronic and electrochemical properties, we evaluate the contributions of electrostriction, Maxwell stress,…
The nanostructural evolution of the strain-induced structural phase transition in BiFeO3 is examined. Using high-resolution X-ray diffraction and scanning-probe microscopy-based studies we have uniquely identified and examined the numerous phases present at these phase boundaries and have discovered an intermediate monoclinic phase in addition to the previously observed rhombohedral- and tetragonal-like phases. Further analysis has determined that the so-called mixed-phase regions of these films are not mixtures of rhombohedral- and tetragonal-like phases, but intimate mixtures of highly-disto…
We perform ab initio calculations of charged graphene and single-wall carbon nanotubes (CNTs). A wealth of electromechanical behaviors is obtained: (1) Both nanotubes and graphene expand upon electron injection. (2) Upon hole injection, metallic nanotubes and graphene display a non-monotonic behavior: Upon increasing hole densities, the lattice constant initially contracts, reaches a minimum, and then starts to expand. The hole densities at minimum lattice constants are 0.3 |e|/atom for graphene and between 0.1 and 0.3 |e|/atom for the metallic nanotubes studied. (3)Semiconducting CNTs with sm…
We demonstrate a class of model nano-electromechanical systems (NEMS) based on multiwalled carbon nanotubes (MWNTs) which has longer inner cores coaxially oscillating inside their respective shorter outer shell holders and can operate at continuously controllable frequencies up to the gigahertz range when fuelled by AC electric fields. Its additional attributes include much larger oscillation amplitudes and forces and much lower rates of thermal dissipation (Q-factor = 10^5) and air damping (Q-factor = 10^4~10^5) than those of nano-beam based NEMS. A crucial feature of the conceived model NEMS…
We present a new generation of nano-electromechanical systems (NEMS), which are realized by doping the semiconductor base material. In contrast to the traditional approach these doped NEMS (D-NEMS) do not require a metallization layer. This makes them far lighter and hence increases resonance frequency and quality factor. Additionally, D-NEMS can be tuned from the conductive state into an insulating one. This will enable a host of new device designs, like mechanically tunable pin-junctions and nanomechanical single electron switches. We demonstrate D-NEMS fabrication and operation from the int…
Strong coupling between electrical and mechanical phenomena and the presence of switchable polarization have enabled applications of ferroelectric materials for nonvolatile memories (FeRAM), data storage, and ferroelectric lithography. Understanding the local functionality of inorganic ferroelectrics including crystallographic orientation, piezoresponse, elasticity, and mechanisms for polarization switching, requires probing material structure and properties on the level of a single ferroelectric grain or domain. Here, I present recent studies on electromechanical, mechanical, and spectroscopi…
Investigating the Electromechanical Behavior of Unconventionally Ferroelectric $Hf_{0.5}Zr_{0.5}O_{2}$-based Capacitors Through Operando Nanobeam X-ray Diffraction
The rapid development of nanoscience and nanotechnology in the last two decades was stimulated by the emergence of scanning probe microscopy (SPM) techniques capable of accessing local material properties, including transport, mechanical, and electromechanical behavior on the nanoscale. Here, we analyze the general principles of electromechanical probing by piezoresponse force microscopy (PFM), a scanning probe technique applicable to a broad range of piezoelectric and ferroelectric materials. The physics of image formation in PFM is compared to Scanning Tunneling Microscopy and Atomic Force M…
Surprising asymmetry in the local electromechanical response across a single antiparallel ferroelectric domain wall is reported. Piezoelectric force microscopy is used to investigate both the in-plane and out-of- plane electromechanical signals around domain walls in congruent and near-stoichiometric lithium niobate. The observed asymmetry is shown to have a strong correlation to crystal stoichiometry, suggesting defect-domain wall interactions. A defect-dipole model is proposed. Finite element method is used to simulate the electromechanical processes at the wall and reconstruct the images. F…
Electromechanical coupling is ubiquitous in nature and underpins the functionality of materials and systems as diverse as ferroelectric and multiferroic materials, electrochemical devices, and biological systems, and strain-based scanning probe microscopy (s-SPM) techniques have emerged as a powerful tool in characterizing and manipulating electromechanical coupling at the nanoscale. Uncovering underlying mechanisms of electromechanical coupling in these diverse materials and systems, however, is a difficult outstanding problem, and questions and confusions arise from recent experiment observa…
Precise manipulation of electronic band structures of two-dimensional (2D) transition metal dichalcogenides and oxides (TMD&Os) via localised strain engineering is an exciting avenue for exploiting their unique characteristics for electronics, optoelectronics, and nanoelectromechanical systems (NEMS) applications. This work experimentally demonstrates that mechanically-induced electrical transitions can be engineered in quasi-2D molybdenum disulphide (MoS2) and molybdenum trioxide (MoO3) using an in situ electrical nanoindentation technique. It is shown that localised strains on such quasi-2D …
It is well recognized that the miniaturization of electromechanical devices will bring a revolution to humanity in the coming decades synonymous with the effects of miniaturizing electronic devices in those previous. An electromechanical actuator - a device that converts electrical energy to mechanical deformation or motion - is the core component of many such devices. Consequently, research interrogating mili-, micro-, and nano-actuation has, and will continue to become increasingly essential. The challenge is that behaviour of actuators at small size scales vastly differs to those at the mac…
Frequency dependent dynamic electromechanical response of the mixed ionic-electronic conductor film to a periodic electric bias is analyzed for different electronic and ionic boundary conditions. Dynamic effects of mobile ions concentration (stoichiometry contribution), charge state of acceptors (donors), electron concentration (electron-phonon coupling via the deformation potential) and flexoelectric effect contribution are discussed. A variety of possible nonlinear dynamic electromechanical response of MIEC films including quasi-elliptic curves, asymmetric hysteresis-like loops with pronounc…
The electrochemical processes in energy storage materials are generally linked with changes of molar volume of the host compound. Here, the frequency dependent strain response of 1D electrochemically active systems to periodic electric bias is analyzed. The sensitivity and resolution of these electrochemical strain measurements are compared to the current-based electrochemical impedance spectroscopy. The resolution and detection limits of interferometric and atomic force microscopy based systems for probing electrochemical reactions on the nanoscale are analyzed.
The ability to probe a materials electromechanical functionality on the nanoscale is critical to applications from energy storage and computing to biology and medicine. Voltage modulated atomic force microscopy (VM-AFM) has become a mainstay characterization tool for investigating these materials due to its unprecedented ability to locally probe electromechanically responsive materials with spatial resolution from microns to nanometers. However, with the wide popularity of VM-AFM techniques such as piezoresponse force microscopy (PFM) and electrochemical strain microscopy (ESM) there has been …
Symmetry breaking at surfaces and interfaces and the capability to support large strain gradients in nanoscale systems enable new forms of electromechanical coupling. Here we introduce the concept of quantum flexoelectricity, a phenomenon that is manifested when the mechanical deformation of non-polar quantum systems results in the emergence of net dipole moments and hence linear electromechanical coupling proportional to local curvature. The concept is illustrated in carbon systems, including polyacetylene and nano graphitic ribbons. Using density functional theory calculations for systems ma…
The transition-metal dichalcogenides (TMD) MoS2 and WS2 show remarkable electromechanical properties. Strain modifies the direct band gap into an indirect one, and substantial strain even induces an semiconductor-metal transition. Providing strain through mechanical contacts is difficult for TMD monolayers, but state-of-the-art for TMD nanotubes. We show using density-functional theory that similar electromechanical properties as in monolayer and bulk TMDs are found for large diameter TMD single- (SWNT) and multi-walled nanotubes (MWNTs). The semiconductor-metal transition occurs at elongation…
We propose a simple analytical model of a metal-oxide-semiconductor field-effect transistor with a lateral resonant gate based on the coupled electromechanical equations, which are self-consistently solved in time. All charge densities according to the mechanical oscillations are evaluated. The only input parameters are the physical characteristics of the device. No extra mathematical parameters are used to fit the experimental results. Theoretical results are in good agreement with the experimental data in static and dynamic operation. Our model is comprehensive and may be suitable for any el…
Piezoresponse force microscopy (PFM) is a powerful tool widely used to characterize piezoelectricity and ferroelectricity at the nanoscale. However, it is necessary to distinguish microscopic mechanisms between piezoelectricity and non-piezoelectric contributions measured by PFM. In this work, we systematically investigate the first and second harmonic apparent piezoresponses of silicon wafer in both vertical and lateral modes, and we show that it exhibits apparent electromechanical response that is quadratic to the applied electric field, possibly arising from ionic electrochemical dipoles in…
Piezoelectrics interconvert mechanical energy and electric charge and are widely used in actuators and sensors. The best performing materials are ferroelectrics at a morphotropic phase boundary (MPB), where several phases can intimately coexist. Switching between these phases by electric field produces a large electromechanical response. In the ferroelectric BiFeO$_3$, strain can be used to create an MPB-like phase mixture and thus to generate large electric field dependent strains. However, this enhanced response occurs at localized, randomly positioned regions of the film, which potentially …
Silicon-compatible ideal antiferroelectricity with large digital electromechanical responses enabled by thermal-strain domain engineering
Harbin Institute of Technology, Shenzhen（哈尔滨工业大学（深圳））；Wuhan University of Technology（武汉理工大学）；University of Liège（列日大学）；Tsinghua University（清华大学）；Institute of Metal Research, Chinese Academy of Sciences（中国科学院金属研究所）；Indian Institute of Science（印度科学学院）；Soochow University（苏州大学）；Institute of Physics, Chinese Academy of Sciences（中国科学院物理研究所）
Recent investigations have shown that highly oxygen defective cerium oxides generate non-classical electrostriction that is superior to lead-based ferroelectrics. In this work, we report the effect of field-assisted spark plasma sintering (SPS) on electro-chemo-mechanical properties on Ca-doped ceria (CDC). Nanometric powders of ca. 10 nm are rapidly consolidated to form polycrystalline nanostructures with a high degree of crystalline disorder. Remarkably, the resultant material demonstrates a large electromechanical strain without a frequency-related relaxation effect. We conclude that electr…
Coupling between electrical and mechanical phenomena is a near-universal characteristic of inorganic and biological systems alike, with examples ranging from ferroelectric perovskites to electromotor proteins in cellular membranes. Understanding electromechanical functionality in materials such as ferroelectric nanocrystals, thin films, relaxor ferroelectrics, and biosystems requires probing these properties on the nanometer level of individual grain, domain, or protein fibril. In the last decade, Piezoresponse Force Microscopy (PFM) was established a powerful tool for nanoscale imaging, spect…
Piezoelectric nanowires are promising materials for sensing, actuation and energy harvesting, due to their enhanced properties at the nanoscale. However, quantitative characterization of piezoelectricity in nanomaterials is challenging due to practical limitations and the onset of additional electromechanical phenomena, such as the triboelectric and piezotronic effects. Here, we present an open-circuit conductive atomic force microscopy (cAFM) methodology for quantitative extraction of the axial piezoelectric coefficients of nanowires. We show, both theoretically and experimentally, that the s…
The interest in ferroelectric van der Waals crystals arises from the potential to realize ultrathin ferroic systems owing to the reduced surface energy of these materials and the layered structure that allows for exfoliation. Here, we quantitatively unravel giant negative electrostriction of van der Waals layered copper indium thiophosphate (CIPS), which exhibits an electrostrictive coefficient Q33 as high as -3.2 m4/C2 and a resulting bulk piezoelectric coefficient d33 up to -85 pm/V. As a result, the electromechanical response of CIPS is comparable in magnitude to established perovskite ferr…
Chiropiezoelectric Energy Harvesting from Lattice-Handedness-Controlled Selenium Nanowires
Korea Advanced Institute of Science and Technology (KAIST)（韩国科学技术院）；Applied Science Research Institute, Korea Advanced Institute of Science and Technology (KAIST)（韩国科学技术院应用科学研究院）；Department of Materials Science and Engineering, Korea Advanced Institute of Science and Technology (KAIST)（韩国科学技术院材料科学与工程系）
Ferroelectric materials have remained one of the foci of condensed matter physics and materials science for over 50 years. In the last 20 years, the development of voltage-modulated scanning probe microscopy techniques, exemplified by Piezoresponse force microscopy (PFM) and associated time and voltage spectroscopies, opened a pathway to explore these materials on a single-digit nanometer level. Consequently, domain structures, walls and polarization dynamics can now be imaged in real space. More generally, PFM has allowed studying electromechanical coupling in a broad variety of materials ran…
We present a novel computational framework to simulate the electromechanical response of self-sensing carbon nanotube (CNT)-based composites experiencing fracture. The computational framework combines electrical-deformation-fracture finite element modelling with a mixed micromechanics formulation. The latter is used to estimate the constitutive properties of CNT-based composites, including the elastic tensor, fracture energy, electrical conductivity, and linear piezoresistive coefficients. These properties are inputted into a coupled electro-structural finite element model, which simulates the…
Two-dimensional (2D) layered materials are ideal for micro- and nanoelectromechanical systems (MEMS/NEMS) due to their ultimate thinness. Platinum diselenide (PtSe$_{2}$), an exciting and unexplored 2D transition metal dichalcogenides (TMD) material, is particularly interesting because its scalable and low temperature growth process is compatible with silicon technology. Here, we explore the potential of thin PtSe$_{2}$ films as electromechanical piezoresistive sensors. All experiments have been conducted with semimetallic PtSe$_{2}$ films grown by thermally assisted conversion of Pt at a CMOS…
We investigate the electromechanical coupling in 2d materials. For non-Bravais lattices, we find important corrections to the standard macroscopic strain - microscopic atomic-displacement theory. We put forward a general and systematic approach to calculate strain-displacement relations for several classes of 2d materials. We apply our findings to graphene as a study case, by combining a tight binding and a valence force-field model to calculate electronic and mechanical properties of graphene nanoribbons under strain. The results show good agreement with the predictions of the Dirac equation …
Lattices of odd-layered two-dimensional (2D) transition metal dichalcogenides (TMDs) such as WSe2 are non-centrosymmetric, and thus could possess linear piezoelectricity that is attractive for applications such as nanoelectromechanical systems (NEMS) and nanogenerators. Measuring the electromechanical coupling of 2D TMDs, however, is rather challenging, since its D3h point group symmetry makes conventional piezoresponse force microscopy (PFM) inapplicable. Here we develop a lateral excitation scanning probe microscopy (SPM) technique that enables mapping of the piezoelectric response of atomic…
