We performed temperature dependent transient photovoltage and photocurrent measurements on poly(3-hexylthiophene):[6,6]-phenyl-C61 butyric acid methylester bulk heterojuction solar cells. We found a strongly charge carrier concentration and temperature dependent Langevin recombination prefactor. The observed recombination mechanism is discussed in terms of bimolecular recombination. The experimental results were compared with charge carrier extraction by linearly increasing voltage (photo-CELIV) measurements done on the same blend system. We explain the charge carrier dynamics, following an apparent order larger than two, by dynamic trapping of charges in the tail states of the gaussian density of states.
Recombination of photogenerated charge carriers in polymer bulk heterojunction (BHJ) solar cells reduces the short circuit current (Jsc) and the fill factor (FF). Identifying the mechanism of recombination is, therefore, fundamentally important for increasing the power conversion efficiency. Light intensity and temperature dependent current-voltage measurements on polymer BHJ cells made from a variety of different semiconducting polymers and fullerenes show that the recombination kinetics are voltage dependent and evolve from first order recombination at short circuit to bimolecular recombinat…
We report both transport measurements and spectroscopic data of polymer/fullerene blend photovoltaics using a small library of fullerene esters to correlate device properties with a range of functionality and structural diversity of the ester substituent. We observe that minor structural changes can lead to significant differences in device efficiency and lifetime. Surprisingly, we have found that isomeric R-groups in the fullerene ester-based devices we have studied have very different efficiencies. The characteristic lifetimes derived from both transport and spectroscopic measurements are ge…
Photoinduced polarons in solid films of polymer-fullerene blends were studied by photoluminescence (PL), photoinduced absorption (PIA) and electron spin resonance (ESR). The donor materials used were P3HT and MEH-PPV. As acceptors we employed PC60BM as reference and various soluble C70-derivates: PC70BM, two different diphenylmethano-[70]fullerene oligoether (C70-DPM-OE) and two dimers, C70-C70 and C60-C70. Blend films containing C70 revealed characteristic spectroscopic signatures not seen with C60. Light-induced ESR showed signals at g\geq2.005, assigned to an electron localized on the C70 c…
Light induced polarons in solid films of polymer-fullerene blends were studied by applying photoluminescence (PL), photo induced absorption (PIA) techniques as well as electron spin resonance (ESR). The materials used were poly(3-hexylthiophene) (P3HT) and poly-[2-methoxy, 5-(2'-ethyl-hexyloxy) phenylene vinylene] (MEH-PPV) as donors. As acceptors we used [6,6]-phenyl-C61-butyric acid methyl ester ([C60]PCBM) and various soluble C70-derivates: [C70]PCBM, diphenylmethano[70]fullerene oligoether (C70-DPM-OE), C70-DPM-OE2, and two fullerene dimers, C70-C70 and C60-C70 (all shown in figure 1). In …
The separation of photogenerated polaron pairs in organic bulk heterojunction solar cells is the intermediate but crucial step between exciton dissociation and charge transport to the electrodes. In state-of-the-art devices, above 80% of all polaron pairs are separated at fields of below $10^7$V/m. In contrast, considering just the Coulomb binding of the polaron pair, electric fields above $10^8$V/m would be needed to reach similar yields. In order to resolve this discrepancy, we performed kinetic Monte Carlo simulations of polaron pair dissociation in donor--acceptor blends, considering deloc…
The ongoing depletion of fossil fuels has led to an intensive search for additional renewable energy sources. Solar-based technologies could provide sufficient energy to satisfy the global economic demands in the near future. Photovoltaic (PV) cells are the most promising man-made devices for direct solar energy utilization. Understanding the charge separation and charge transport in PV materials at a molecular level is crucial for improving the efficiency of the solar cells. Here, we use light-induced EPR spectroscopy combined with DFT calculations to study the electronic structure of charge …
Blends of polymer and C$_{60}$-derived molecules are in the spotlight in recent years for application in organic photovoltaics, forming what is known as bulk-heterojunction active layers. The character of the heterojunction is determinant, with clear relevance of morphology and phase separation. To better understand the morphology of the systems, we present a classical molecular dynamics (CMD) simulation of polymer/fullerene (P3HT/C$_{60}$) blends, coming from different starting points, using the specifically designed Nanomol Force Field based on the Universal Force Field. We use not-so-short …
Non-fullerene acceptors based on perylenediimides (PDIs) have garnered significant interest as an alternative to fullerene acceptors in organic photovoltaics (OPVs), but their charge transport phenomena are not well understood, especially in bulk heterojunctions (BHJs). Here, we investigate charge transport and current fluctuations by performing correlated low-frequency noise and impedance spectroscopy measurements on two BHJ OPV systems, one employing a fullerene acceptor and the other employing a dimeric PDI acceptor. In the dark, these measurements reveal that PDI-based OPVs have a greater …
Organic solar cells have the potential to be low-cost and efficient solar energy converters, with a promising energy balance. They are made from carbon-based semiconductors, which exhibit favourable light absorption and charge generation properties, and can be manufactured by low temperature processes such as printing from solvent-based inks, which are compatible with flexible plastic substrates or even paper. In this review, we will present an overview of the physical function of organic solar cells, their state-of-the-art performance and limitations, as well as novel concepts to achieve a be…
We theoretically investigate the dynamical stability of one-dimensional fullerene polymers by computing the phonon dispersion relations within the atomistic approach. We find that only seven models among 54 models proposed previously [J. Phys. Chem. A 119, 3048 (2015)] are dynamically stable. We show that the low temperature specific heat of them is proportional to the square root of the temperature in a wider range of temperature compared to the case of single-walled carbon nanotubes.
The work concerns the analysis of experimental time-resolved ESR spectra in photoexcited polymer:fullerene blend, consisting of poly(3-hexilthiophene) and fullerene [6,6]-phenyl C_{61} -butyric acid methyl ester (at low temperature T = 100 K). The spectra are assumed to be determined by spin-coherent pairs of charged polarons P^{+} and P^{-} generated in the singlet state. The analysis is made within simple model of a set of first order processes, in which P^{+}P$^{-}-pair spin evolution is described by the stochastic Liouville equation, allowing for fairly accurate description of experimental…
We report transient electron paramagnetic resonance (trEPR) measurements with sub-microsecond time resolution performed on a P3HT:PCBM blend at low temperature. The trEPR spectrum immediately following photoexcitation reveals signatures of spin-correlated polaron pairs. The pair partners (positive polarons in P3HT and negative polarons in PCBM) can be identified by their characteristic g-values. The fact that the polaron pair states exhibit strong non-Boltzmann population unambiguously shows that the constituents of each pair are geminate, i.e. originate from one exciton. We demonstrate that c…
The two-dimensional polymer structure and lattice dynamics of the superionic conductor Li4 C60 are investigated by neutron diffraction and spectroscopy. The peculiar bonding architecture of this compound is definitely confirmed through the precise localisation of the carbon atoms involved in the intermolecular bonds. The spectral features of this phase are revealed through ab-initio lattice dynamics calculations and inelastic neutron scattering experiments. The neutron observables are found to be in very good agreement with the simulations which predict a partial charge transfer from the Li at…
The time dependence of device performance has been measured for photocells using blends containing the conjugated polymer, poly[2-methoxy-5-(2-ethylhexyloxy)-1,4-phenylenevinylene] (MEH-PPV) with two different functionalized C60 electron acceptor molecules: commercially available [6,6]-phenyl C61 butyric acid methyl ester (PCBM) or [6,6]-phenyl C61 butyric acid octadecyl ester (PCBOD) produced in this laboratory. Performance was characterized by the short-circuit current output of the devices, with the time dependence of PCBM samples typically degrading exponentially. Variations in the charact…
In this work, a novel electrospun conductive polymer nanocomposite made of polycaprolactone with an exohedral complex made of multiwalled carbon nanotubes and fullerene C60 was prepared and characterized. The preparation was straightforward and the complexes self-assembled within the nanocomposite fibers. The nanocomposite showed electrical switching behavior due to charge accumulation of fullerene C60 upon electrical stimulation. Write-once read-many memory devices were fabricated by electrospinning a nanocomposite with 0.8%wt. fullerene C60 onto interdigitated coplanar electrodes. The device…
Organic solar cells (OSCs) have recently shown a rapid improvement in their performance, bringing power conversion efficiencies (PCEs) closer to the point where commercial applications of the technology become viable. However, the low open-circuit voltage (Voc) of OSCs relative to their optical gap still limits PCEs to below 20%. A key factor contributing to the large Voc deficit in OSCs is non-radiative recombination to spin-triplet excitons, which is widely, but not universally, observed in blends using both fullerene and non-fullerene electron acceptors. Here, we present an experimental fra…
We present a theory of the electronic structure and photophysics of 1:1 blends of derivatives of polyparaphenylenevinylene and fullerenes. Within the same Coulomb-correlated Hamiltonian applied previously to interacting chains of single-component $π$-conjugated polymers, we find an exciplex state that occurs below the polymer's optical exciton. Weak absorption from the ground state occurs to the exciplex. We explain transient photoinduced absorptions in the blend, observed for both above-gap and below-gap photoexcitations, within our theory. Photoinduced absorptions for above-gap photoexcitati…
In polymeric semiconductors, charge carriers are polarons, which means that the excess charge deforms the molecular structure of the polymer chain that hosts it. This effect results in distinctive signatures in the vibrational modes of the polymer. We probe polaron photo- generation dynamics at polymer:fullerene heterojunctions by monitoring its time-resolved resonance-Raman spectrum following ultrafast photoexcitation. We conclude that polarons emerge within 200 fs, which is nearly two orders of magnitude faster than exciton localisation in the neat polymer film. Surprisingly, further vibrati…
We investigate the mechanical properties of $π$-conjugated polymeric materials composed of regioregular poly(3-hexylthiophene) (P3HT) and fullerene C$_{60}$ using coarse-grained molecular dynamics simulations. Specifically, we perform tensile simulations of P3HT:C$_{60}$ composites with varied degrees of polymerization and C$_{60}$ mass fractions to obtain their stress-strain responses. Decomposition of stress tensor into kinetic energy and virial contributions indicates that the tensile moduli of the pure P3HT samples are greatly dependent on non-bonded interactions and on bonded interactions…
We investigated photogeneration yield and recombination dynamics in blends of poly(3-hexyl thiophene) (P3HT) and poly[2-methoxy-5-(30,70-dimethyloctyloxy)-1,4-phenylenevinylene] (MDMO-PPV) with [6,6]- phenyl-C61 butyric acid methyl ester (PC61BM) by means of temperature dependent time delayed collection field (TDCF) measurements. In MDMO-PPV:PC61BM we find a strongly field dependent polaron pair dissociation which can be attributed to geminate recombination in the device. Our findings are in good agreement with field dependent photoluminescence measurements published before, supporting a scena…
Hybrid conjugated polymer/fullerene filaments based on MEH-PPV/PVP/PCBM are prepared by electrospinning, and their properties assessed by scanning electron, atomic and lateral force, tunnelling, and confocal microscopy, as well as by attenuated total reflection Fourier transform-infrared spectroscopy, photoluminescence quantum yield and spatially-resolved fluorescence. Highlighted features include ribbon-shape of the realized fibers, and the persistence of a network serving as a template for heterogeneous active layers in solar cell devices. A set of favorable characteristics is evidenced in t…
Organic solar cells (OSCs) based on ADA-type (acceptor-donor-acceptor) non-fullerene acceptors (NFAs) exhibit improved power conversion efficiency (PCE) compared to the conventional fullerene-based analogues. The optoelectronic properties of OSC active layer blends are correlated to their underlying structural dynamics and therefore influence the device performance. Using synergistically different neutron spectroscopy techniques, we studied the dynamics of binary and ternary blends made of the NFAs O-IDTBR and O-IDFBR and the regioregular donor polymer P3HT. Deuteration was considered for a co…
Non-radiative recombination processes are the biggest hindrance to approaching the radiative limit of the open-circuit voltage for wide-band gap perovskite solar cells. In addition, to high bulk quality, good interfaces and good energy level alignment for majority carriers at charge transport layer-absorber interfaces are crucial to minimize non-radiative recombination pathways. By tuning the lowest-unoccupied molecular-orbital of electron transport layers via the use of different fullerenes and fullerene blends, we demonstrate open-circuit voltages exceeding 1.35 V in CH3NH3Pb(I0.8Br0.2)3 dev…
The power conversion efficiencies (PCEs) of organic solar cells (OSCs) using non-fullerene acceptors (NFAs) have now reached 18%. However, this is still lower than inorganic solar cells, for which PCEs >20% are commonplace. A key reason is that OSCs still show low open-circuit voltages (Voc) relative to their optical band gaps, attributed to non-radiative recombination. For OSCs to compete with inorganics in efficiency, all non-radiative loss pathways must be identified and where possible, removed. Here, we show that in most NFA OSCs, the majority of charge recombination at open-circuit procee…
In polymer:fullerene solar cells, the origin of the losses in the field-dependent photocurrent is still controversially debated. We contribute to the ongoing discussion by performing photo-induced charge extraction measurements on poly(3-hexylthiophene-2,5-diyl):[6,6]-phenyl-C$_{61}$ butyric acid methyl ester solar cells in order to investigate the processes ruling charge carrier decay. Calculating the drift length of photogenerated charges, we find that polaron recombination is not limiting the photocurrent for annealed devices. Additionally, we applied Monte Carlo simulations on blends of co…
The major loss mechanism of photogenerated polarons was investigated in P3HT:PCBM solar cells by the photo-CELIV technique. For pristine and annealed devices, we find that the experimental data can be explained by a bimolecular recombination rate reduced by a factor of about ten (pristine) and 25 (annealed) as compared to Langevin theory. Aided by a macroscopic device model, we discuss the implications of the lowered loss rate on the characteristics of polymer:fullerene solar cells.
Driven by the rapid development of non-fullerene electron acceptors (NFAs), the power conversion efficiencies of organic solar cells (OSCs) have reached levels suitable for commercial applications. However, the poor operational stability of high-performance NFA OSCs is a remaining fundamental challenge that must be addressed. Whilst previous studies have primarily focused on the NFA component, we consider here the degradation pathways of both the donor and acceptor materials in the benchmark PM6:Y6 blend. Here, we show that light soaking greatly increases the energetic disorder and trap state …
Colloidal zinc oxide (ZnO) nanoparticles are frequently used in the field of organic photovoltaics for the realization of solution-producible, electron-selective interfacial layers. Despite of the widespread use, there is a lack of detailed investigations regarding the impact of structural properties of the particles on the device performance. In this work, ZnO nanoparticles with varying surface-area-to-volume ratio were synthesized and implemented into polymer-fullerene bulk heterojunction solar cells with a gas-permeable top electrode. By comparing the electrical characteristics before and a…
We present a neutron spectroscopy based method to study quantitatively the partial miscibility and phase behaviour of an organic photovoltaic active layer made of conjugated polymer:small molecule blends, presently illustrated with the regio-random poly(3-hexylthiophene-2,5-diyl) and fullerene [6,6]-Phenyl C$_{61}$ butyric acid methyl ester (RRa-P3HT:PCBM) system. We perform both inelastic neutron scattering and quasi-elastic neutron scattering measurements to study the structural dynamics of blends of different compositions enabling us to resolve the phase behaviour. The difference of neutron…
New monolayer 2D carbon structures, namely qHPC60 and qTPC60, were recently synthesized by covalently bonding C60 polymers. Here, we carried out Reactive (ReaxFF) molecular dynamics simulations to study the thermodynamic stability and fracture patterns of qHPC60 and qTPC60. Our results showed that these structures present similar thermal stability, with sublimation points of 3898K and 3965K, respectively. qHPC60 and qTPC60 undergo an abrupt structural transition becoming totally fractured after a critical strain threshold. The crack propagation is linear (non-linear) for qHPC60 (qTPC60). The e…
Charge carrier recombination is studied in operational organic solar cells made from the polymer:fullerene system PCDTBT:PC71BM (poly[N-9"-heptadecanyl-2,7-carbazole-alt-5,5-(4',7'-di-2-thienyl-2',1',3'-benzothiadiazole)] : [6,6]-phenyl-C$_{70}$-butyric acid methyl ester). A newly developed technique High Intensity Resistance dependent PhotoVoltage (HI-RPV) is presented for reliably quantifying the bimolecular recombination coefficient independently of variations in experimental conditions, thereby resolving key limitations of previous experimental approaches. Experiments are performed on sola…
Earlier reports demonstrated that ternary organic solar cells (OSC) made of donor polymers (D) blended with different mixtures of fullerene acceptors (A:A) performed very similarly. This finding is surprising, as the corresponding fullerene LUMO levels are slightly different, which might result in decisive differences in the charge transfer step. We investigate ternary OSC (D:A:A) made of the donor polymer P3HT with stoichiometric mixtures of different fullerene derivatives, PC60BM:PC70BM and PC70BM:IC60BA, respectively. Using quantitative electron paramagnetic resonance (EPR) we can distingui…
Bridging the lab-to-fab gap in non-fullerene organic solar cells via gravure printing
Institute for Print and Media Technology, Chemnitz University of Technology（印刷与媒体技术研究所，开姆尼茨工业大学）；Institute of Physics, Chemnitz University of Technology（物理研究所，开姆尼茨工业大学）；Department of Engineering, Durham University（工程系，杜伦大学）
Time-dependent measurements of both power conversion efficiency and ultraviolet-visible absorption spectroscopy have been observed for solar cell blends containing the polymer poly(3-hexylthiophene-2,5-diyl) (P3HT) with two different functionalized C60 electron acceptor molecules: commercially available [6,6]-phenyl C61 butyric acid methyl ester (PCBM) or [6,6]-phenyl C61 butyric acid octadecyl ester (PCBOD) produced in this laboratory. Efficiency was found to decay with an exponential time dependence, while spectroscopic features show saturating exponential behavior. Time constants extracted …
The active layer crystallinity has long been associated with favourable organic solar cells (OSCs) properties such as high mobility and Fill Factor. In particular, this applies to acceptor materials such as fullerene-derivatives and the most recent Non-Fullerene Acceptors (NFAs), which are now surpassing 19% of Power Conversion Efficiency. Despite these advantages are being commonly attributed to their 3-dimensional crystal packing motif in the single crystal, the bridge that links the acceptor crystal packing from single crystals to solar cells has not clearly been shown yet. In this work, we…
Organic bulk-heterojunctions (BHJ) and solar cells containing the trimetallic nitride endohedral fullerene 1-[3-(2-ethyl)hexoxy carbonyl]propyl-1-phenyl-Lu3N@C80 (Lu3N@C80-PCBEH) show an open circuit voltage (VOC) 0.3 V higher than similar devices with [6,6]-phenyl-C[61]-butyric acid methyl ester (PC61BM). To fully exploit the potential of this acceptor molecule with respect to the power conversion efficiency (PCE) of solar cells, the short circuit current (JSC) should be improved to become competitive with the state of the art solar cells. Here, we address factors influencing the JSC in blend…
Wavelength-Dependent Photoluminescence Mapping of Depth-Dependent Degradation Under Thermal Stress in Phenethylammonium Tetrafluoroborate Treated Perovskite Solar Cells
Inclusion of heavy metal atoms in a polymer backbone allows transitions between the singlet and triplet manifolds. Interfacial dissociation of triplet excitons constitutes a viable mechanism for enhancing photovoltaic (PV) efficiencies in polymer heterojunction-based solar cells. The PV efficiency from polymer solar cells utilizing a ladder-type poly (para-phenylene) polymer (PhLPPP) with trace quantity of Pd atoms and a fullerene derivative (PCBM) is much higher than its counterpart (MeLPPP) with no Pd atom. Evidence is presented for the formation of a weak ground-state charge-transfer comple…
The slow decay of charge carriers in polymer-fullerene blends measured in transient studies has raised a number of questions about the mechanisms of nongeminate recombination in these systems. In an attempt to understand this behavior, we have applied a combination of steady-state and transient photoinduced absorption measurements to compare nongeminate recombination behavior in films of neat poly(3-hexyl thiophene) (P3HT) and P3HT blended with [6,6]-phenyl-C61 butyric acid methyl ester (PCBM). Transient measurements show that carrier recombination in the neat P3HT film exhibits second-order d…
We develop a model for charge trapping on conjugated polymer chains using a continuous representation of the polymer. By constraining the motion to along the chain, we find that kinks along the chain serve as points of attraction and can induce localization and spontaneous buckling of the chain. We implement this in a model system of a conjugated polymer donor and fullerene acceptor to mimic a polymer based photovoltaic system. We find that geometric fluctuations of the polymer give rise to deep potential energy traps at kinks which are often stronger than the Coulomb interaction between the e…
Influence of Charge Carrier Mobility on the Performance of Organic Solar Cells
基于供体-受体共混物的有机太阳能电池的功率转换效率由极化子对解离和双分子极化子复合的相互作用决定。这两个过程都强烈依赖于载流子的迁移率，解离随着更快的电荷传输而增加，同时提高了复合损失。使用宏观有效介质模拟，我们计算了最佳的载流子迁移率的最高功率转换效率，第一次占注入势垒和减少Langevin型复合。载流子迁移率从现有技术聚合物：富勒烯太阳能电池的$10^{-8}$ m $^2$ /Vs提高到产生最大效率的约$10^{-6}$ m $^2$ /Vs，对应于给定参数组仅约20%的提高。
Recombination losses contribute to reduce $J_{SC}$, $V_{OC}$ and the fill factor of organic solar cells. Recent advances in non-fullerene organic photovoltaics have shown, nonetheless, that efficient charge generation can occur under small energetic driving forces ($ΔE_{DA}$) and low recombination losses. To shed light on this issue, we set up a coarse-grained open quantum mechanical model for investigating the charge generation dynamics subject to various energy loss mechanisms. The influence of energetic driving force, Coulomb interaction, vibrational disorder, geminate recombination, temper…
Electric fields are central to the operation of optoelectronic devices based on conjugated polymers since they drive the recombination of electrons and holes to excitons in organic light-emitting diodes but are also responsible for the dissociation of excitons in solar cells. One way to track the microscopic effect of electric fields on charge carriers formed under illumination of a polymer film is to exploit the fluorescence arising from delayed recombination of carrier pairs, a process which is fundamentally spin dependent. Such spin-dependent recombination can be probed directly in fluoresc…
We studied the recombination dynamics of charge carriers in organic bulk heterojunction solar cells made of the blend system poly(2,5-bis(3-dodecyl thiophen-2-yl) thieno[2,3-b]thiophene) (pBTCT-C12):[6,6]-phenyl-C61-butyric acid methyl ester (PC61BM) with a donor--acceptor ratio of 1:1 and 1:4. The techniques of charge carrier extraction by linearly increasing voltage (photo-CELIV) and, as local probe, time-resolved microwave conductivity (TRMC) were used. We observed a difference in the initially extracted charge carrier concentration in the photo-CELIV experiment by one order of magnitude, w…
Understanding of degradation mechanisms in polymer:fullerene bulk-heterojunctions on the microscopic level aimed at improving their intrinsic stability is crucial for the breakthrough of organic photovoltaics. These materials are vulnerable to exposure to light and/or oxygen, hence they involve electronic excitations. To unambiguously probe the excited states of various multiplicities and their reactions with oxygen, we applied combined magneto-optical methods based on multifrequency (9 and 275 GHz) electron paramagnetic resonance (EPR), photoluminescence (PL), and PL-detected magnetic resonan…
A polysquaraine low band gap polymer was synthesized by Yamamoto coupling of a monomeric dibromo indolenine squaraine dye. The resulting polymer has a weight average molar mass in the order of Mw ~30.000-50.000 and a polydispersity of ca. 1.7 as determined by gel-permeation chromatography (GPC). The electronic properties of monomer and polymer were investigated by cyclic voltammetry, absorption and emission spectroscopy. Owing to exciton coupling the absorption bands of the polymer are red-shifted and strongly broadened compared to the monomer squaraine dye. Bulk heterojunction solar cells wer…
Open circuit voltage decay measurements are performed on methylammonium lead iodide (CH3NH3PbI3) perovskite solar cells to investigate the charge carrier recombination dynamics. The measurements are compared to the two reference polymer-fullerene bulk heterojunction solar cells based on P3HT:PC60BM and PTB7:PC70BM blends. In the perovskite devices, two very different time domains of the voltage decay are found, with a first drop on a short time scale that is similar to the organic solar cells. However, two major differences are also observed. 65-70% of the maximum photovoltage persists on much…
Distinguishing Carrier Transport and Interfacial Recombination at Perovskite-Transport Layer Interfaces Using Ultrafast Spectroscopy and Numerical Simulation
The mechanism of electron-hole separation in organic solar cells is currently hotly debated. Recent experimental work suggests that these charges can separate on extremely short timescales (<100 fs). This can be understood in terms of delocalised transport within fullerene aggregates, which is thought to emerge on short timescales before vibronic relaxation induces polaron formation. However, in the optimal heterojunction morphology, electrons and holes will often re-encounter each other before reaching the electrodes. If such charges trap and cannot separate, then device efficiency will suffe…
All-organic-based photovoltaic solar cells have attracted considerable attention because of their low-cost processing and short energy payback time. In such systems the primary dissociation of an optical excitation into a pair of photocarriers has been recently shown to be extremely rapid and efficient, but the physical reason for this remains unclear. Here, two-dimensional photocurrent excitation spectroscopy, a novel non-linear optical spectroscopy, is used to probe the ultrafast coherent decay of photoexcitations into charge-producing states in a polymer:fullerene based solar cell. The two-…
Defects in low-bandgap polymer based photodetectors play a critical role in determining switching characteristics in the near infra-red spectral-regime relevant to communication wavelength. We carry out detailed studies of the bandwidth limiting factors of the long-live transient photocurrent at different incident wavelength as a function of temperature, light pulse width, bias voltage. The results indicate that dominant transport mechanism of the photogenerated carriers is limited by recombination at low temperature and detrapping rate at high temperature. A general trend of a slower response…
Organic solar cells (OSCs) containing an active layer consisting of a nanostructured blend of a conjugated polymer like poly(3-hexylthiophene) (P3HT) and an electron acceptor molecule have the potential of competing against silicon-based photovoltaic panels. However, this potential is unfulfilled primarily due to interrelated production and stability issues. The generally employed spin coating process for fabricating organic solar cells cannot be scaled up. Recently, He et al., have reported that the gelation of P3HT with [6,6]-phenyl-C61-butyric acid methyl ester (PC60BM) under sub-ambient co…
