Miron J. Cristea
The current-voltage p-n junction characteristics were mainly analyzed until now at low injection levels and high level injection separately. This work unifies the low injection, medium injection, high injection levels and the ohmic region of the I/V characteristics. Keywords: p-n junctions, current-voltage characteristics, low injection and high injection levels, ohmic region.
机构、总结、中文摘要均由AI分析而来，可能存在错误，请以论文正文为准。
继续探索
We have carried out calculations of current-voltage characteristics for the electron tunnel current through a junction with a thin insulating ferroelectric barrier assuming that interface transmissions for the left and right interfaces noticeably differ due to dissimilarity of the interfaces. Obtained conductance versus voltage and current versus voltage curves exhibit well distinguishable asymmetric hysteresis. We show that the asymmetry in the hysteretic effects could originate from the asymmetric bias voltage profile inside the junction. In particular, we analyze the hysteresis asymmetries …
We studied the response of a ferromagnet-insulator-normal metal tunnel structure under an external oscillating radio frequency (R.F.) magnetic field. The D. C. voltage across the junction is calculated and is found not to decrease despite the high resistance of the junction; instead, it is of the order of $μV$ to $100μV$, much larger than the experimentally observed value (100 nano-V) in the "strong coupled" ohmic ferromagnet-normal metal bilayers. This is consistent with recent experimental results in tunnel structures, where the voltage is larger than $μV$s. The damping and loss of an extern…
In this paper we report what happens to a pristine oxide junction Pr0.5Ca0.5MnO3/SrTi0.95Nb.05O3 (PCMO/Nb:STO), when it is subjected to cycling of voltage bias of moderate value ({\pm}4V). It is found that the initial cycling leads to formation of a permanent state of lower resistance where the lower resistance arises predominantly due to development of a shunt across the device film (PCMO). On successive voltage cycling with increasing magnitude, this state transforms into states of successive lower resistance that can be transformed back to the initial stable state on cycling to below a cert…
In contrast to graphene which is a gapless semiconductor, graphane, the hydrogenated graphene, is a semiconductor with an energy gap. Together with the two-dimensional geometry, unique transport features of graphene, and possibility of doping graphane, p and n regions can be defined so that 2D p-n junctions become feasible with small reverse currents. This paper introduces a basic analysis to obtain current-voltage characteristics of such a 2D p-n junction based on graphane. As we show, within the approximation of Shockley law of junctions, an ideal I-V charactristic for this p-n junction is t…
Transport properties have been studied for a perovskite heterojunction consisting of SrRuO$_{3}$ (SRO) film epitaxially grown on SrTi$_{0.99}$Nb$_{0.01}$O$_{3}$ (Nb:STO) substrate. The SRO/Nb:STO interface exhibits rectifying current-voltage ($I$-$V$) characteristics agreeing with those of a Schottky junction composed of a deep work-function metal (SRO) and an $n$-type semiconductor (Nb:STO). A hysteresis appears in the $I$-$V$ characteristics, where high resistance and low resistance states are induced by reverse and forward bias stresses, respectively. The resistance switching is also trigge…
We investigate bias voltage effects on the spin-dependent transport properties of Fe/MgAl${}_2$O${}_4$/Fe(001) magnetic tunneling junctions (MTJs) by comparing them with those of Fe/MgO/Fe(001) MTJs. By means of the nonequilibrium Green's function method and the density functional theory, we calculate bias voltage dependences of magnetoresistance (MR) ratios in both the MTJs. We find that in both the MTJs, the MR ratio decreases as the bias voltage increases and finally vanishes at a critical bias voltage $V_{\rm c}$. We also find that the critical bias voltage $V_{\rm c}$ of the MgAl${}_2$O${…
Theoretical investigations of spin transfer torque in magnetic tunnel junctions using the tight-binding model in the framework of non-equilibrium Green functions formalism are presented. We show that the behavior of the spin transfer torque as a function of applied voltage can vary over a wide range depending on the band parameters of the ferromagnetic electrodes and the insulator that comprise the magnetic tunnel junction. The behavior of both the parallel and perpendicular components of the spin torque is addressed. This behavior is explained in terms of the spin and charge current dependenc…
The temperature dependence of a vortex-based nano-oscillator induced by spin transfer torque (STVO) in magnetic tunnel junctions (MTJ) is considered. We obtain emitted signals with large output power and good signal coherence. Due to the reduced non-linearities compared to the uniform magnetization case, we first observe a linear decrease of linewidth with decreasing temperature. However, this expected behavior no longer applies at lower temperature and a bottom limit of the linewidth is measured.
Temperature- and bias voltage-dependent transport measurements of magnetic tunnel junctions (MTJs) with perpendicularly magnetized Co/Pd electrodes are presented. Magnetization measurements of the Co/Pd multilayers are performed to characterize the electrodes. The effects of the Co layer thickness in the Co/Pd bilayers, the annealing temperature, the Co thickness at the MgO barrier interface, and the number of bilayers on the tunneling magneto resistance (TMR) effect are investigated. TMR-ratios of about 11 % at room temperature and 18.5 % at 13 K are measured and two well-defined switching fi…
Magnetic tunnel junctions (MTJ) with AlOx barrier were fabricated by a deposition tool called Biased Target Ion Beam Deposition (BTIBD) using low energy ion source (0-50 eV) and voltage biased targets. The BTIBD system applies bias voltage directly and only on the desired targets, providing enough sputtering energy and avoiding "overspill" contamination during film deposition. The successful deposition of AlOx-MTJs demonstrated the capability of BTIBD to make multilayer structures with good film quality. MTJ thin film surface roughness and intermixing between layers are among the key problems …
Thermoelectric junctions are often made of components of different materials characterized by distinct transport properties. Single material junctions, with the same type of charge carriers, have also been considered to investigate various classical and quantum effects on the thermoelectric properties of nanostructured materials. We here introduce the concept of defect-induced thermoelectric voltage, namely, {\it thermodefect voltage}, in graphene nanoribbon (GNR) junctions under a temperature gradient. Our thermodefect junction is formed by two GNRs with identical properties except the existe…
We theoretically study the recently observed tunnel-barrier-enhanced dc voltage signals generated by magnetization precession in magnetic tunnel junctions. While the spin pumping is suppressed by the high tunneling impedance, two complimentary processes are predicted to result in a sizable voltage generation in ferromagnet (F)|insulator (I)|normal-metal (N) and F|I|F junctions, with one ferromagnet being resonantly excited. Magnetic dynamics in F|I|F systems induces a robust charge pumping, translating into voltage in open circuits. In addition, dynamics in a single ferromagnetic layer develop…
Using self-energy-corrected density functional theory (DFT) and a coherent scattering-state approach, we explain current-voltage (IV) measurements of four pyridine-Au and amine-Au linked molecular junctions with quantitative accuracy. Parameter-free many-electron self-energy corrections to DFT Kohn-Sham eigenvalues are demonstrated to lead to excellent agreement with experiments at finite bias, improving upon order-of-magnitude errors in currents obtained with standard DFT approaches. We further propose an approximate route for prediction of quantitative IV characteristics for both symmetric a…
Current-voltage characteristics and $P-E$ loops are simulated in SrRuO$_{3}$/BaTiO$_{3}$/Pt tunneling junctions with interfacial dead layer. The unswitchable interfacial polarization is coupled with the screen charge and the barrier polarization self-consistently within the Thomas-Fermi model and the Landau-Devonshire theory. The shift of P-E loop from the center position and the unequal values of the positive coercive field and the negative coercive field are found, which are induced by the asymmetricity of interface dipoles. A complete J-V curve of the junction is shown for different barrier…
In the persistent photoconductivity (PPC) phenomenon, illumination of a YBCO thin film junction with a 1mW He-Ne laser leads to the decrease of the critical critical voltage (similar to the threshold voltage). The decrease of the critical votage was reversed by illumination with incadenscent light. The critical voltage across the junction was experimentally decreased and increased by alternating illumination between He-Ne laser and incandescent light. We also observed visible quenching of the photo-induced state using a 5mW He-Ne laser. Finally, the threshold behavior of the junction was destr…
We demonstrate a voltage-controlled exchange bias effect in CoFeB/MgO/CoFeB magnetic tunnel junctions that is related to the interfacial Fe(Co)Ox formed between the CoFeB electrodes and the MgO barrier. The unique combination of interfacial antiferromagnetism, giant tunneling magnetoresistance, and sharp switching of the perpendicularly-magnetized CoFeB allows sensitive detection of the exchange bias. It is found that the exchange bias field can be isothermally controlled by magnetic fields at low temperatures. More importantly, the exchange bias can also be effectively manipulated by the elec…
Low voltage local strain enhanced switching of magnetic tunnel junctions
针对 CoFeB-MgO 基磁隧道结应变调控电压过高的问题，本文利用局部栅极电场诱导应变，在 200 mV 低电压下实现开关场控制和隧道磁阻线性增强。
Voltage-induced ferromagnetic resonance (V-FMR) in magnetic tunnel junctions (MTJs) with a W buffer is investigated. Perpendicular magnetic anisotropy (PMA) energy is controlled by both thickness of a CoFeB free layer deposited directly on the W buffer and a post-annealing process at different temperatures. The PMA energy as well as the magnetization damping are determined by analysing field-dependent FMR signals in different field geometries. An optimized MTJ structure enabled excitation of V-FMR at frequencies exceeding 30 GHz. The macrospin modelling is used to analyse the field- and angula…
Using first-principles calculations based on density functional theory combined with the non-equilibrium Green's function approach, the transport behaviors of a single-molecule junction formed by benzenedithiol connected to gold electrodes are investigated. The breakdown voltage for the model of benzenedithiol plus gold electrodes is 0.7 V, which is close to the experimental value. A linear response between the conductance and temperature (known as linear temperature drift) is found in the molecular device, which indicates that it could be used to maintain the stability of molecular circuits. …
We assess the performances of the transition voltage spectroscopy (TVS) method to determine the energies of the molecular orbitals involved in the electronic transport though molecular junctions. A large number of various molecular junctions made with alkyl chains but with different chemical structure of the electrode-molecule interfaces are studied. In the case of molecular junctions with clean, unoxidized electrode-molecule interfaces, i.e. alkylthiols and alkenes directly grafted on Au and hydrogenated Si, respectively, we measure transition voltages in the range 0.9 - 1.4 V. We conclude th…
We present experimental evidence and physics-based simulations of the lock-on effect in high-voltage GaAs avalanche diodes. The avalanche triggering is initiated by steep voltage ramp applied to the diode and in-series 50 Ohm load. After subnanosecond avalanche switching the reversely biased GaAs diode remains in the conducting state for the whole duration of the applied pulse (dozens of nanoseconds). There is no indication of the p-n junction recovery that is commonly expected to develop on the nanosecond scale due to the drift extraction of non-equilibrium carriers. The diode voltage keeps a…
The thermoelectric voltage developed across an atomic metal junction (i.e., a nanostructure in which one or a few atoms connect two metal electrodes) in response to a temperature difference between the electrodes, results from the quantum interference of electrons that pass through the junction multiple times after being scattered by the surrounding defects. Here we report successfully tuning this quantum interference and thus controlling the magnitude and sign of the thermoelectric voltage by applying a mechanical force that deforms the junction. The observed switching of the thermoelectric v…
The temperature and voltage dependence of spin transport is theoretically investigated in a new type of magnetic tunnel junction, which consists of two ferromagnetic outer electrodes separated by a ferromagnetic barrier and a nonmagnetic (NM) metallic spacer. The effect of spin fluctuation in magnetic barrier, which plays an important role at finite temperature, is included by taking the mean-field approximation. It is found that, the tunnel magnetoresistance (TMR) and the electron-spin polarization depend strongly on the temperature and the applied voltage. The TMR and spin polarization at di…
We present the concept of ferroelectric tunnel junctions (FTJs). These junctions consist of two metal electrodes separated by a nanometer-thick ferroelectric barrier. The current-voltage characteristics of FTJs are analyzed under the assumption that the direct electron tunneling represents the dominant conduction mechanism. First, the influence of converse piezoelectric effect inherent in ferroelectric materials on the tunnel current is described. The calculations show that the lattice strains of piezoelectric origin modify the current-voltage relationship owing to strain-induced changes of th…
We have investigated metallic break junctions of the heavy-fermion compound UPd2Al3 at low temperatures between 0.1K and 9K and in magnetic fields up to 8T. Both the current-voltage I(V) characteristics and the dV/dI (V) spectra clearly showed the superconducting ($T_{\rm c}\simeq$ 1.8K) as well as the antiferromagnetic ($T_{\rm N}\simeq$14K) transition at low temperatures when the bias voltage is raised. The junctions with lateral size of order 200nm had huge critical current densities around $5\times 10^{10} A/m^2 at the antiferromagnetic transition and hysteretic I(V) characteristics. Degra…
In this paper we will report an experimental approach for directly determining the photogenerated current at individual junctions within the triple junction solar cell. The method is based on the measurement of different current-voltage curves; one with the usual illumination system, normally AM0 or AM1.5G, and the other curves with a light source, having a different spectral emission. The fitting of all current-voltage curves simultaneously, not individually, permit us to determine the photogenerated current of three junctions. It is necessary to have three characteristics or more. An example…
Atomically thin chromium triiodide (CrI3) has recently been identified as a layered antiferromagnetic insulator, in which adjacent ferromagnetic monolayers are antiferromagnetically coupled. This unusual magnetic structure naturally comprises a series of anti-aligned spin filters which can be utilized to make spin-filter magnetic tunnel junctions with very large tunneling magnetoresistance (TMR). Here we report voltage control of TMR formed by four-layer CrI3 sandwiched by monolayer graphene contacts in a dual-gated structure. By varying the gate voltages at fixed magnetic field, the device ca…
We study the combined effects of spin transfer torque, voltage modulation of interlayer exchange coupling and magnetic anisotropy on the switching behavior of perpendicular magnetic tunnel junctions (p-MTJs). In asymmetric p-MTJs, a linear-in-voltage dependence of interlayer exchange coupling enables the effective perpendicular anisotropy barrier to be lowered for both voltage polarities. This mechanism is shown to reduce the critical switching current and effective activation energy. Finally, we analyze the possibility of having switching via interlayer exchange coupling only.
Recently, several groups have reported spin-dependent thermoelectric effects in magnetic tunnel junctions. In this paper, we present a setup for time-resolved measurements of thermovoltages and thermocurrents of a single micro- to nanometer-scaled tunnel junction. An electrically modulated diode laser is used to create a temperature gradient across the tunnel junction layer stack. This laser modulation technique enables the recording of time-dependent thermovoltage signals with a temporal resolution only limited by the preamplifier for the thermovoltage. So far, time-dependent thermovoltage co…
The radio-frequency (RF) voltage amplification property of a tunnel magnetoresistance device driven by an RF external-magnetic-field-induced ferromagnetic resonance was studied. The proposed device consists of a magnetic tunnel junction (MTJ) and an electrically isolated coplanar waveguide. The input RF voltage applied to the waveguide can excite the resonant dynamics in the free layer magnetization, leading to the generation of an output RF voltage under a DC bias current. The dependences of the RF voltage gain on the static external magnetic field strength and angle were systematically inves…
Low voltage graphene interface engineered organic ferroelectric tunnel junction devices
本文通过界面层工程，在单层石墨烯上沉积超薄铁电薄膜制备铁电隧道结，实现了约0.8V的低压极化切换和显著的隧道电阻，解决了铁电材料低电压应用的障碍。
Application of Bardeen's tunneling theory to magnetic tunnel junctions having a general degree of atomic disorder reveals the close relationship between magneto-conduction and voltage-driven pseudo-torque, as well as the thickness dependence of tunnel-polarization factors. Among the results: 1) The torque generally varies as sin theta at constant applied voltage. 2) Whenever polarization factors are well defined, the voltage-driven torque on each moment is uniquely proportional to the polarization factor of the other magnet. 3) At finite applied voltage, this relation predicts significant volt…
Voltage-driven spin transfer torque in a magnetic tunnel junction comprising magnetic insulating electrodes is studied theoretically. In contrast with the conventional magnetic tunnel junctions comprising transition metal ferromagnets, the spin transfer torque presents unconventional bias dependencies, related to the presence of spin-dependent Fowler-Nordheim tunneling processes. In particular, we find that (i) the out-of-plane torque generally dominates the in-plane torque, (ii) out-of-plane torque and in-plane torque are symmetric and asymmetric at low bias voltage, respectively, and (iii) b…
扫码添加微信好友，提出您的宝贵建议 👇
💡 备注请填写：网站反馈
发表机构由 AI 从论文文本抽取，如发现错误，欢迎反馈修正建议。