Material failure by crack propagation essentially involves a concentration of large displacement-gradients near a crack's tip, even at scales where no irreversible deformation and energy dissipation occurs. This physical situation provides the motivation for a systematic gradient expansion of general nonlinear elastic constitutive laws that goes beyond the first order displacement-gradient expansion that is the basis for linear elastic fracture mechanics (LEFM). A weakly nonlinear fracture mechanics theory was recently developed by considering displacement-gradients up to second order. The theory predicts that, at scales within a dynamic lengthscale $\ell$ from a crack's tip, significant $\log{r}$ displacements and $1/r$ displacement-gradient contributions arise. Whereas in LEFM the $1/r$ singularity generates an unbalanced force and must be discarded, we show that this singularity not only exists but is {\em necessary} in the weakly nonlinear theory. The theory generates no spurious forces and is consistent with the notion of the autonomy of the near-tip nonlinear region. The J-integral in the weakly nonlinear theory is also shown to be path-independent, taking the same value as the linear elastic J-integral. Thus, the weakly nonlinear theory retains the key tenets of fracture mechanics, while providing excellent quantitative agreement with measurements near the tip of single propagating cracks. As $\ell$ is consistent with lengthscales that appear in crack tip instabilities, we suggest that this theory may serve as a promising starting point for resolving open questions in fracture dynamics.
The recently developed weakly nonlinear theory of dynamic fracture predicts $1/r$ corrections to the standard asymptotic linear elastic $1/\sqrt{r}$ displacement-gradients, where $r$ is measured from the tip of a tensile crack. We show that the $1/r$ singularity does not automatically conform with the notion of autonomy (autonomy means that any crack tip nonlinear solution is uniquely determined by the surrounding linear elastic $1/\sqrt{r}$ fields) and that it does not automatically satisfy the resultant Newton's equation in the crack parallel direction. We show that these two properties are …
On the basis of energy conservation law an without utilizing Linear Fracture Mechanics (LFM) postulates the equation of a real-structure material elastic-plastic fracture has been derived. With the help of this equation the force and energy criteria of Non-linear Fracture Mechanics (NLFM) have been found. These criteria constitute the basis of modern strength analysis of machineparts and structures made of real-structure materials. $K_{lc}$ dependence on ultimate strength limit, yield limit and impact toughness has been established and experimentally confirmed for a number of steels
In this review article we consider the crack growth resistance ofmicrometer and submicrometer sized samples from the fracture mechanics point of view. Standard fracture mechanics test procedures were developed for macroscale samples, and reduction of the specimen dimensions by three to five orders of magnitude has severe consequences. This concerns the interpretation of results obtained by micro and nanomechanics, as well as the life time and failure prediction of micro and nano devices. We discuss the relevant fracture mechanics length scales and their relation to the material specific struct…
We extend the model-free data-driven paradigm for rate-independent fracture mechanics proposed in Carrara et al. (2020), Data-driven Fracture Mechanics, Comp. Meth. App. Mech. Eng., 372 to rate-dependent fracture and sub-critical fatigue. The problem is formulated by combining the balance governing equations stemming from variational principles with a set of data points that encodes the fracture constitutive behavior of the material. The solution is found as the data point that best satisfies the meta-stability condition as given by the variational procedure and following a distance minimizati…
Rapid progress in additive manufacturing methods has created a new class of ultralight and strong architected metamaterials that resemble periodic truss structures. The mechanical performance of these metamaterials with a very large number of unit cells is ultimately limited by their tolerance to damage and defects, but an understanding of this sensitivity has remained elusive. Using a stretching-dominated micro-architecture and metamaterial specimens comprising millions of unit-cells we show that not only is the stress intensity factor, as used in conventional elastic fracture mechanics, insu…
In terms of nonlinear material fracture mechanics, the real (discrete)-structure material fracture model has been developed. The model rests on the demonstration of the fact that crack resistance $K_{1c}=2σ\sqrt l$ and fracture toughness are $G_{1c}=J_{1c}=2σl$ obtained on the basis of energy conservation law and derived without linear material fracture mechanics assumptions can be respectively taken as force and energy criteria for non-linear fracture mechanics. It is shown that $G_{1c}=K_{1c}^2/E$ is the energy criterion of linear fracture mechanics of material and it is sufficiently less th…
Microbond tests composed of single fibre and matrix droplet are often used to determine the properties of fibre reinforced composites. Interfacial shear strength is quantified by the maximum pull-out force assuming a uniform stress distribution along the fibre. Here, nonlinear finite element analyses are performed to investigate the validity of this assumption.
In this work, we developed a bond-based cohesive peridynamics model (CPDM) and apply it to simulate inelastic fracture by using the meso-scale Xu-Needleman cohesive potential . By doing so, we have successfully developed a bond-based cohesive continuum mechanics model with intrinsic stress/strain measures as well as consistent and built-in macro-scale constitutive relations. The main novelties of this work are: (1) We have shown that the cohesive stress of the proposed nonlocal cohesive continuum mechanics model is exactly the same as the nonlocal peridynamic stress; (2) For the first time, we…
In this paper we first obtain the order of stress singularity for a dynamically propagating self-affine fractal crack. We then show that there is always an upper bound to roughness, i.e. a propagating fractal crack reaches a terminal roughness. We then study the phenomenon of reaching a terminal velocity. Assuming that propagation of a fractal crack is discrete, we predict its terminal velocity using an asymptotic energy balance argument. In particular, we show that the limiting crack speed is a material-dependent fraction of the corresponding Rayleigh wave speed.
The topologies of existing interface elements used to discretize cohesive cracks are such that they can be used to compute the relative displacements (displacement discontinuities) of two opposing segments (in 2D) or of two opposing facets (in 3D) belonging to the opposite crack faces and enforce the cohesive traction-separation relation. In the present work we propose a novel type of interface element for fracture mechanics sharing some analogies with the node-to-segment (in 2D) and with the node-to-surface (in 3D) contact elements. The displacement gap of a node belonging to the finite eleme…
It was shown that a material fatigue fracture diagram can be viewed as a locus of points with $σ$ and $\sqrt l$ coordinates' product equal to $K_{1c}/2$, and $σ$ and $l$ product -- to $G_{1c}/2$, where $K_{1c}$ and $G_{1c}$ are non-linear fracture mechanics force and energy criteria. It was established that the average number of interatomic bonds destroyed within one alternate stress $\nabla_{1cs}$ cycle is directly proportional to $σ$ that is twice as large as a peak value of $σ^a$. It was found that low-cycle fatigue is characterized by $σ>σ_{0.2}$ and $σ_{1cs}> 1$, high-cycle fatigue -- by …
We investigate the influence of gradient-enhanced dislocation hardening on the mechanics of notch-induced failure. The role of geometrically necessary dislocations (GNDs) in enhancing cracking is assessed by means of a mechanism-based strain gradient plasticity theory. Both stationary and propagating cracks from notch-like defects are investigated through the finite element method. A cohesive zone formulation incorporating monotonic and cyclic damage contributions is employed to address both loading conditions. Computations are performed for a very wide range of length scale parameters and num…
The mechanical properties of the stoichiometric B2 $β$-phase of NiAl are well established, however the effect of off-stoichiometric composition on the fracture toughness has not yet been systematically studied over the entire composition range of 40-50% Al. Here we use microbending tests on notched cantilever beams FIB-milled from NiAl single crystals with an aluminized as well as an oxidation-induced composition gradient to determine the influence of the Al concentration on the mechanical properties. The fracture toughness is maximal for the stoichiometric composition. It decreases with incre…
In this work the global and local mechanical properties of the magnetocaloric intermetallic LaFe11.2Si1.8 alloy are investigated by a combination of different testing and characterization techniques in order to shed light on the partly contradictory data in recent literature. Macroscale compression tests were performed to illuminate the global fracture behavior and evaluate it statistically. LaFe11.2Si1.8 demonstrates a brittle behavior with fracture strains below 0.6 % and widely distributed fracture stresses of 180-620 MPa leading to a Weibull modulus of m = 2 to 6. The local mechanical prop…
This work presents a critical overview of the effects of different aspects of model formulation on crack path selection in quasi-static phase field fracture. We consider different evolution methods, mechanics formulations, fracture dissipation energy formulations, and forms of the irreversibility condition. The different model variants are implemented with common numerical methods based on staggered solution of the phase-field and mechanics sub-problems via FFT-based solvers. These methods mix standard approaches with novel elements, such as the use of bound-constrained conjugate gradients for…
When a frictional interface is subject to a localized shear load, it is often (experimentally) observed that local slip events initiate at the stress concentration and propagate over parts of the interface by arresting naturally before reaching the edge. We develop a theoretical model based on linear elastic fracture mechanics to describe the propagation of such precursory slip. The model's prediction of precursor lengths as a function of external load is in good quantitative agreement with laboratory experiments as well as with dynamic simulations, and provides thereby evidence to recognize f…
We use classical molecular dynamics (MD) simulations to investigate the mechanical properties of pre-cracked, nano-porous single layer MoS2 (SLMoS2) and the effect of interactions between cracks and pores. We found that the failure of pre-cracked and nano-porous SLMoS2 is dominated by brittle type fracture. Bonds in armchair direction show a stronger resistance to crack propagation compared to the zigzag direction. We compared the brittle failure of Griffith prediction with the MD fracture strength and toughness and found substantial differences that limit the applicability of Griffith criteri…
Monolayer antimonene has drawn the attention of research communities due to its promising physical properties. But mechanical properties of antimonene is still largely unexplored. In this work, we investigate the mechanical properties and fracture mechanisms of two stable phases of monolayer antimonene -- the $α$ antimonene ($α$-Sb) and the $β$ antimonene ($β$-Sb), through molecular dynamics (MD) simulations. Our simulations reveal that stronger chiral effect results in a greater anisotropic elastic behavior in $β$-antimonene than in $α$-antimonene. In this paper we focus on crack-tip stress d…
This study presents the formulation, the numerical solution, and the validation of a theoretical framework based on the concept of variable-order mechanics and capable of modeling dynamic fracture in brittle and quasi-brittle solids. More specifically, the reformulation of the elastodynamic problem via variable and fractional order operators enables a unique and extremely powerful approach to model nucleation and propagation of cracks in solids under dynamic loading. The resulting dynamic fracture formulation is fully evolutionary hence enabling the analysis of complex crack patterns without r…
The fundamental problem of friction in the presence of macroscopic adhesion, as in soft bodies, is receiving interest from many experimentalists. Since the first fracture mechanics `purely brittle' model of Savkoor and Briggs, models have been proposed where the mixed mode toughness is interpreted with phenomenological fitting coefficients introducing weaker coupling between modes than expected by the "purely brittle" model. We compare here two such previously proposed models and introduce a third one to show that the transition to sliding is very sensitive to the form of the mixed-mode model.…
We study a planar thin brittle beam subject to elastic deformations and cracks described in terms of a nonlinear Griffith energy functional acting on $SBV$ deformations of the beam. In particular we consider the case in which elastic bulk contributions due to finite bending of the beam are comparable to the surface energy which is necessary to completely break the beam into several large pieces. In the limit of vanishing aspect ratio we rigorously derive an effective Griffith-Euler-Bernoulli functional which acts on piecewise $W^{2,2}$ regular curves representing the midline of the beam. The e…
The dynamics of materials failure is one of the most critical phenomena in a range of scientific and engineering fields, from healthcare to structural materials to transportation. In this paper we propose a specially designed deep neural network, DyFraNet, which can predict dynamic fracture behaviors by identifying a complete history of fracture propagation - from cracking onset, as a crack grows through the material, modeled as a series of frames evolving over time and dependent on each other. Furthermore, this model can not only forecast future fracture processes but also backcast to elucida…
Many people are aware of the theory of elastic fracture originated by AA Griffith, and although Griffith used the theorem of minimum potential energy most people seem unaware of the broader implications of this theorem. If it is set within its classical mechanics roots, it is clear that it is a restricted form of a Lagrangian. In advanced texts on fracture cracks are treated as dynamic entities, and the role of stress waves is clearly articulated. However, in most non-advanced texts on fracture and fatigue the role of stress waves are either not included or not emphasised, often leading to a p…
As recently suggested in an interestring and stimulating paper by Menga, Carbone & Dini (MCD), applying fracture mechanics energy concepts for the case of a sliding adhesive contact, imposing also the shear stress is constant at the interface and equal to a material constant (as it seems in experiments), leads to a increase of contact area which instead is never observed. We add that the rigorous MCD theory also predict a size effect and hence a distortion of the JKR curve during sliding which is also not observed in experiments. Finally, a simpler example with the pure mode I contact case, le…
Graphene and some graphene like two dimensional materials; hexagonal boron nitride (hBN) and silicene have unique mechanical properties which severely limit the suitability of conventional theories used for common brittle and ductile materials to predict the fracture response of these materials. This study revealed the fracture response of graphene, hBN and silicene nanosheets under different tiny crack lengths by molecular dynamics (MD) simulations using LAMMPS. The useful strength of these large area two dimensional materials are determined by their fracture toughness. Our study shows a comp…
Stretchable conductors are of crucial relevance for emerging technologies such as wearable electronics, low-invasive bioelectronic implants or soft actuators for robotics. A critical issue for their development regards the understanding of defect formation and fracture of conducting pathways during stress-strain cycles. Here we present a novel atomic force microscopy (AFM) method that provides multichannel images of surface morphology, conductivity, and elastic modulus during sample deformation. To develop the method, we investigate in detail the mechanical interactions between the AFM tip and…
The effects of shear on energy release rate and mode mixity in a symmetric sandwich beam with isotropic layers and a debond crack at the face sheet/core interface are investigated through a semi-analytic approach based on two-dimensional elasticity and linear elastic fracture mechanics. Semi-analytic expressions are derived for the shear components of energy release rate and mode mixity phase angle which depend on four numerical coefficients derived through accurate finite element analyses. The expressions are combined with earlier results for three-layer configurations subjected to bending-mo…
We consider the effect of differing coefficients of static and dynamic friction coefficients on the behaviour of contacts involving microslip. The classic solutions of Cattaneo and Mindlin are unchanged if the transition in coefficients is abrupt, but if it occurs over some small slip distance, the solution has some mathematical similarities with those governing the normal tractions in adhesive contact problems. In particular, if the transition to dynamic slip occurs over a sufficiently small area, we can identify a `JKR' approximation, where the transition region is condensed to a line. A loc…
The failure of frictional interfaces -- the process of frictional rupture -- is widely assumed to feature crack-like properties, with far-reaching implications for various disciplines, ranging from engineering tribology to earthquake physics. An important condition for the emergence of a crack-like behavior is the existence of stress drops in frictional rupture, whose basic physical origin has been recently elucidated. Here we show that for generic and realistic frictional constitutive relations, and once the necessary conditions for the emergence of an effective crack-like behavior are met, f…
