The capability to control the type and amount of charge carriers in a material and, in the extreme case, the transition from metal to insulator is one of the key challenges of modern electronics. By employing angle resolved photoemission spectroscopy (ARPES) we find that a reversible metal to insulator transition and a fine tuning of the charge carriers from electrons to holes can be achieved in epitaxial bilayer and single layer graphene by molecular doping. The effects of electron screening and disorder are also discussed. These results demonstrate that epitaxial graphene is suitable for electronics applications, as well as provide new opportunities for studying the hole doping regime of the Dirac cone in graphene.
We studied the effect of quantum confinement on the size of the band gap in single layer epitaxial graphene. Samples with different graphene terrace sizes are studied by using low energy electron microscopy (LEEM) and angle-resolved photoemission spectroscopy (ARPES). The direct correlation between the terrace size extracted from LEEM and the gap size extracted from ARPES shows that quantum confinement alone cannot account for the large gap observed in epitaxial graphene samples.
The pi bands of epitaxially grown graphene are studied by using high resolution angle resolved photoemission spectroscopy. Clear deviations from the conical dispersion expected for massless Dirac fermions and an anomalous increase of the scattering rate are observed in the vicinity of the Dirac point energy. Possible explanations for such anomalies are discussed in terms of many-body interactions and the opening of a gap. We present detailed experimental evidences in support of the gap scenario. This finding reveals a fundamental intrinsic property of epitaxial graphene and demonstrates the po…
We investigate the ultrafast relaxation dynamics of hot Dirac fermionic quasiparticles in multilayer epitaxial graphene using ultrafast optical differential transmission spectroscopy. We observe DT spectra which are well described by interband transitions with no electron-hole interaction. Following the initial thermalization and emission of high-energy phonons, the electron cooling is determined by electron-acoustic phonon scattering, found to occur on the time scale of 1 ps for highly doped layers, and 4-11 ps in undoped layers. The spectra also provide strong evidence for the multilayer stu…
The materials science of graphene grown epitaxially on the hexagonal basal planes of SiC crystals is reviewed. We show that the growth of epitaxial graphene on Si-terminated SiC(0001) is much different than growth on the C-terminated SiC(000 -1) surface, and discuss the physical structure of these graphenes. The unique electronic structure and transport properties of each type of epitaxial graphene is described, as well as progress toward the development of epitaxial graphene devices. This materials system is rich in subtleties, and graphene grown on the two polar faces differs in important wa…
Graphene oxide (GO) flakes have been deposited to bridge the gap between two epitaxial graphene electrodes to produce all-graphene devices. Electrical measurements indicate the presence of Schottky barriers (SB) at the graphene/graphene oxide junctions, as a consequence of the band-gap in GO. The barrier height is found to be about 0.7 eV, and is reduced after annealing at 180 $^\circ$C, implying that the gap can be tuned by changing the degree of oxidation. A lower limit of the GO mobility was found to be 850 cm$^2$/Vs, rivaling silicon. {\it In situ} local oxidation of patterned epitaxial gr…
A new model for graphene, epitaxially grown on silicon carbide is proposed. Density functional theory modelling of epitaxial graphene functionalization by hydrogen, fluorine and phenyl groups has been performed with hydrogen and fluorine showing a high probability of cluster formation in high adatom concentration. It has also been shown that the clusterization of fluorine adatoms provides midgap states in formation due to significant flat distortion of graphene. The functionalization of epitaxial graphene using larger species (methyl and phenyl groups) renders cluster formation impossible, due…
Graphene is a promising contender to succeed the throne of silicon in electronics. To this goal, large-scale epitaxial growth of graphene on substrates should be developed. Among various methods along this line, epitaxial growth of graphene on SiC substrates by thermal decomposition of surface layers has proved itself quite satisfactory both in quality and in process reliability. Even modulation of structural and hence electronic properties of graphene is possible by tuning the graphene/SiC interface structure. The challenges for this graphene-on-SiC technology, however, are the abdication of …
We report results from two-dimensional Raman spectroscopy studies of large-area epitaxial graphene grown on SiC. Our work reveals unexpectedly large variation in Raman peak position across the sample resulting from inhomogeneity in the strain of the graphene film, which we show to be correlated with physical topography by coupling Raman spectroscopy with atomic force microscopy. We report that essentially strain free graphene is possible even for epitaxial graphene.
High-performance graphene field-effect transistors have been fabricated on epitaxial graphene synthesized on a two-inch SiC wafer, achieving a cutoff frequency of 100 GHz for a gate length of 240 nm. The high-frequency performance of these epitaxial graphene transistors not only shows the highest speed for any graphene devices up to date, but it also exceeds that of Si MOSFETs at the same gate length. The result confirms the high potential of graphene for advanced electronics applications, marking an important milestone for carbon electronics.
Quasi-free standing epitaxial graphene is obtained on SiC(0001) by hydrogen intercalation. The hydrogen moves between the 6root3 reconstructed initial carbon layer and the SiC substrate. The topmost Si atoms which for epitaxial graphene are covalently bound to this buffer layer, are now saturated by hydrogen bonds. The buffer layer is turned into a quasi-free standing graphene monolayer with its typical linear pi-bands. Similarly, epitaxial monolayer graphene turns into a decoupled bilayer. The intercalation is stable in air and can be reversed by annealing to around 900 degrees Celsius.
Epitaxial strain has been shown to drive structural phase transitions along with novel functionalities in perovskite-based thin-films. Aliovalent doping at the A-site can drive an insulator-to-metal and magnetic transitions in perovskites along with a variety of interesting structural and electronic phenomena. Using first-principles calculations, we demonstrate here, how coupling epitaxial strain with A-site hole doping in a multiferroic double perovskite, Bi2FeCrO6, could lead to mitigation of issues related to anti-site defects and lowered magnetisation in thin-films of the material. We also…
We show using scanning tunneling microscopy, spectroscopy, and ab initio calculations that several intercalation structures exist for Na in epitaxial graphene on SiC(0001). Intercalation takes place at room temperature and Na electron-dopes the graphene. It intercalates in-between single-layer graphene and the carbon-rich interfacial layer. It also penetrates beneath the interfacial layer and decouples it to form a second graphene layer. This decoupling is accelerated by annealing and is verified by direct Na deposition onto the interface layer. Our observations show that intercalation in grap…
We have measured the electrical response to NO$_2$, N$_2$, NH$_3$ and CO for epitaxial graphene and quasi freestanding epitaxial graphene on 6H-SiC substrates. Quasi freestanding epitaxial graphene shows a 6 fold increase in NO2 sensitivity compared to epitaxial graphene. Both samples show a sensitivity better than the experimentally limited 1 ppb. The strong increase in sensitivity of quasi freestanding epitaxial graphene can be explained by a Fermi-energy close to the Dirac Point leading to a strongly surface doping dependent sample resistance. Both sensors show a negligible sensitivity to N…
Raman spectra were measured for mono-, bi- and trilayer graphene grown on SiC by solid state graphitization, whereby the number of layers was pre-assigned by angle-resolved ultraviolet photoemission spectroscopy. It was found that the only unambiguous fingerprint in Raman spectroscopy to identify the number of layers for graphene on SiC(0001) is the linewidth of the 2D (or D*) peak. The Raman spectra of epitaxial graphene show significant differences as compared to micromechanically cleaved graphene obtained from highly oriented pyrolytic graphite crystals. The G peak is found to be blue-shift…
The Diels-Alder surface modified top epitaxial graphene layer, with newly created pair of sp3 carbon centres, results in abrupt minimization of interlayer van der Waals interactions between two stacked graphene planes, and escapes the wafer during post-reaction manipulation stage, leaving the layer under it almost pristine-like. Above picture shows Diels-Alder functionalized sp2/sp3 graphene adduct leaves the parent wafer. In this communication we systematically address several fundamental questions in graphene surface chemistry, which are of extreme importance for device fabrication, and in s…
We investigated the electroluminescent properties of the epitaxial graphene/SiC junction. The temperature and current dependence of electroluminescence from the epitaxial graphene/SiC is measured within a temperature range of 50-300 K. The result of electroluminescence at 300~K is compared with the electroluminescent spectra from aluminium/SiC junction. The difference between the spectra is explained by the different band bending, which could lead to the tunable LED due to the semi-metal character of the graphene. We observed the electroluminescence at both bias polarities and we described the…
The observation of the anomalous quantum Hall effect in exfoliated graphene flakes triggered an explosion of interest in graphene. It was however not observed in high quality epitaxial graphene multilayers grown on silicon carbide substrates. The quantum Hall effect is shown on epitaxial graphene monolayers that were deliberately grown over substrate steps and subjected to harsh processing procedures, demonstrating the robustness of the epitaxial graphene monolayers and the immunity of their transport properties to temperature, contamination and substrate imperfections. The mobility of the mon…
We demonstrate hydrogen assisted growth of high quality epitaxial graphene on the C-face of 4H-SiC. Compared with the conventional thermal decomposition technique, the size of the growth domain by this method is substantially increased and the thickness variation is reduced. Based on the morphology of epitaxial graphene, the role of hydrogen is revealed. It is found that hydrogen acts as a carbon etchant. It suppresses the defect formation and nucleation of graphene. It also improves the kinetics of carbon atoms via hydrocarbon species. These effects lead to increase of the domain size and the…
The recent discovery of the ability to perform direct epitaxial growth of graphene layers on semiconductor Ge surfaces led to the huge interest to this topic. One of the reasons for this interest is the chance to overcome several present-day drawbacks on the way of the graphene integration in the modern semiconductor technology. The other one is connected with the fundamental studies of the new graphene-semiconductor interfaces, that might help with the deeper understanding of mechanisms, which governs graphene growth on different substrates as well as shed light on the interaction of graphene…
The development of graphene electronics requires the integration of graphene devices with Si-CMOS technology. Most strategies involve the transfer of graphene sheets onto silicon, with the inherent difficulties of clean transfer and subsequent graphene nano-patterning that degrades considerably the electronic mobility of nanopatterned graphene. Epitaxial graphene (EG) by contrast is grown on an essentially perfect crystalline (semi-insulating) surface, and graphene nanostructures with exceptional properties have been realized by a selective growth process on tailored SiC surface that requires …
We study the charge transfer between a quasi-free-standing monolayer graphene, produced by hydrogen intercalation, and surface acceptor states. We consider two models of acceptor density of states to explain the high hole densities observed in graphene and find the density responsivity to the gate voltage. By studying magneto-oscillations of the carrier density we provide an experimental way to determine the relevant model.
We have measured optical absorption in mid-infrared spectral range on hydrogen intercalated epitaxial graphene grown on silicon face of SiC. We have used attenuated total reflection geometry to enhance absorption related to the surface and SiC/graphene interface. The samples of epitaxial graphene have been intercalated in the temperature range of 790 to 1250$^\circ$C and compared to the reference samples of hydrogen etched SiC. We have found that although the Si-H bonds form at as low temperatures as 790$^\circ$C, the well developed bond order has been reached only for epitaxial graphene inter…
The formation of graphene on any desirable substrate is extremely essential for the successful replacement of Si with graphene in all technological applications in the beyond-CMOS era. Recently, we observed that a Ti layer formed on epitaxial graphene by electron-beam evaporation has the sufficiently large area of contact with the surface of epitaxial graphene for the exfoliation process to take place. We also observed that the exfoliated FLG on the Ti layer can be easily transferred onto a SiO2/Si substrate. In this paper, we have proposed a new technique for transferring graphene having a la…
The interaction of graphene with metallic substrates reveals phenomena and properties of great relevance for applications in nanotechnology. In this review, the vibrational characterization by means of various inelastic scattering spectroscopies are surveyed for graphene epitaxially grown on metals and transition carbides. In particular, the manifestations of electron-phonon interaction, such as Kohn anomalies, the evaluation of elastic properties and the nanoscale control of phonon modes are presented and discussed.
Graphene grown epitaxially on SiC has been proposed as a material for carbon-based electronics. Understanding the interface between graphene and the SiC substrate will be important for future applications. We report the ability to image the interface structure beneath single-layer graphene using scanning tunneling microscopy. Such imaging is possible because the graphene appears transparent at energies of 1 eV above or below the Fermi energy. Our analysis of calculations based on density functional theory shows how this transparency arises from the electronic structure of a graphene layer on a…
The application of graphene in electronic devices requires large scale epitaxial growth. The presence of the substrate, however, usually reduces the charge carrier mobility considerably. We show that it is possible to decouple the partially sp3-hybridized first graphitic layer formed on the Si-terminated face of silicon carbide from the substrate by gold intercalation, leading to a completely sp2-hybridized graphene layer with improved electronic properties.
Graphene has shown great application potentials as the host material for next generation electronic devices. However, despite its intriguing properties, one of the biggest hurdles for graphene to be useful as an electronic material is its lacking of an energy gap in the electronic spectra. This, for example, prevents the use of graphene in making transistors. Although several proposals have been made to open a gap in graphene's electronic spectra, they all require complex engineering of the graphene layer. Here we show that when graphene is epitaxially grown on the SiC substrate, a gap of ~ 0.…
Combining scanning tunneling microscopy and angle-resolved photoemission spectroscopy, we demonstrate how to tune the doping of epitaxial graphene from p to n by exploiting the structural changes that occur spontaneously on the Ge surface upon thermal annealing. Furthermore, using first principle calculations we build a model that successfully reproduces the experimental observations. Since the ability to modify graphene electronic properties is of fundamental importance when it comes to applications, our results provide an important contribution towards the integration of graphene with conven…
Three types of first generation epitaxial graphene field effect transistors (FET) are presented and their relative merits are discussed. Graphene is epitaxially grown on both the carbon and silicon faces of hexagonal silicon carbide and patterned with electron beam lithography. The channels have a Hall bar geometry to facilitate magnetoresistance measurements. FETs patterned on the Si-face exhibit off-to-on channel resistance ratios that exceed 30. C-face FETs have lower off-to-on resistance ratios, but their mobilities (up to 5000 cm2/Vs) are much larger than that for Si-face transistors. Ini…
We review progress in developing epitaxial graphene as a material for carbon electronics. In particular, improvements in epitaxial graphene growth, interface control and the understanding of multilayer epitaxial graphene's electronic properties are discussed. Although graphene grown on both polar faces of SiC is addressed, our discussions will focus on graphene grown on the (000-1) C-face of SiC. The unique properties of C-face multilayer epitaxial graphene have become apparent. These films behave electronically like a stack of nearly independent graphene sheets rather than a thin Bernal-stack…
We analyse doping of graphene grown on SiC in two models which differ by the source of charge transfered to graphene, namely, from SiC surface and from bulk donors. For each of the two models, we find the maximum electron density induced in monolayer and bilayer graphene, which is determined by the difference between the work function for electrons in pristine graphene and donor states on/in SiC, and analyse the responsivity of graphene to the density variation by means of electrostatic gates.
Graphene is attractive for spintronics due to its long spin life time and high mobility. So far only thick and polycrystalline slabs have been used as ferromagnetic electrodes. We report the growth of flat, epitaxial ultrathin Co films on graphene. These display perpendicular magnetic anisotropy in the thickness range 0.5-1nm, which is confirmed by theory. PMA, epitaxy and ultrathin thickness bring new perspectives for graphene-based spintronic devices such as the zero-field control of an arbitrary magnetization direction, band matching between electrodes and graphene, and interface effects su…
Epitaxial graphene on SiC possesses, quite remarkably, an electron spectrum similar to that of freestanding samples. Yet, the coupling to the substrate, albeit small, affects the quasiparticle properties. Combining \emph{ab initio} calculations with symmetry analysis, we derive a modified Dirac-Weyl Hamiltonian for graphene epilayers. While for the epilayer on the C-face the Dirac cone remains almost intact, for epilayers on the Si-face the band splitting is about 30\,meV. At certain energies, the Dirac bands are significantly distorted by the resonant interaction with interface states, which …
In recent years, graphene growth optimization has been one of the key routes towards large-scale, high-quality graphene production. We have measured in-situ residual gas content during epitaxial graphene growth on silicon carbide (SiC) to find detrimental factors of epitaxial graphene growth. The growth conditions in high vacuum and purified argon are compared. The grown epitaxial graphene is studied by Raman scattering mapping and mechanical strain, charge density, number of graphene layers and graphene grain size are evaluated. Charge density and carrier mobility has been studied by Hall eff…
The maximum oscillation frequency (fmax) quantifies the practical upper bound for useful circuit operation. We report here an fmax of 70 GHz in transistors using epitaxial graphene grown on the C-face of SiC. This is a significant improvement over Si-face epitaxial graphene used in the prior high frequency transistor studies, exemplifying the superior electronics potential of C-face epitaxial graphene. Careful transistor design using a high κ dielectric T-gate and self-aligned contacts, further contributed to the record-breaking fmax.
The thermal decomposition of SiC surface provides, perhaps, the most promising method for the epitaxial growth of graphene on a material useful in the electronics platform. Currently, efforts are focused on a reliable method for the growth of large-area, low-strain epitaxial graphene that is still lacking. We report here a novel method for the fast, single-step epitaxial growth of large-area homogeneous graphene film on the surface of SiC(0001) using an infrared CO2 laser (10.6 μm) as the heating source. Apart from enabling extreme heating and cooling rates, which can control the stacking orde…
We present a new fabrication method for epitaxial graphene on SiC which enables the growth of ultra-smooth defect- and bilayer-free graphene sheets with an unprecedented reproducibility, a necessary prerequisite for wafer-scale fabrication of high quality graphene-based electronic devices. The inherent but unfavorable formation of high SiC surface terrace steps during high temperature sublimation growth is suppressed by rapid formation of the graphene buffer layer which stabilizes the SiC surface. The enhanced nucleation is enforced by decomposition of polymer adsorbates which act as a carbon …
The growth of graphene by catalytic decomposition of ethylene on Cu(111) in an ultra-high vacuum system was investigated with low energy electron diffraction, low energy electron microscopy, and atomic force microscopy. Attempts to form a graphene overlayer using ethylene at pressures as high as 10 mTorr and substrate temperatures as high as 900 $^\circ$C resulted in almost no graphene growth. By using an argon overpressure, the growth of epitaxial graphene on Cu(111) was achieved. The suppression of graphene growth without the use of an argon overpressure is attributed to Cu sublimation at el…
We study the broadband optical conductivity and ultrafast carrier dynamics of epitaxial graphene in the few-layer limit. Equilibrium spectra of nominally buffer, monolayer, and multilayer graphene exhibit significant terahertz and near-infrared absorption, consistent with a model of intra- and interband transitions in a dense Dirac electron plasma. Non-equilibrium terahertz transmission changes after photoexcitation are shown to be dominated by excess hole carriers, with a 1.2-ps mono-exponential decay that reflects the minority-carrier recombination time.
The study of the nanomechanics of graphene $-$ and other 2D materials $-$ has led to the discovery of exciting new properties in 2D crystals, such as their remarkable in-plane stiffness and out of plane flexibility, as well as their unique frictional and wear properties at the nanoscale. Recently, nanomechanics of graphene has generated renovated interest for new findings on the pressure-induced chemical transformation of a few-layer thick epitaxial graphene into a new ultra-hard carbon phase, named diamene. In this work, by means of a machine learning technique, we provide a fast and efficien…
We report a direct correlation between carrier mobility and Raman topography of epitaxial graphene (EG) grown on silicon carbide (SiC). We show the Hall mobility of material on the Si-face of SiC [SiC(0001)] is not only highly dependent on thickness uniformity but also on monolayer strain uniformity. Only when both thickness and strain are uniform over a significant fraction (> 40%) of the device active area does the mobility exceed 1000 cm2/V-s. Additionally, we achieve high mobility epitaxial graphene (18,100 cm2/V-s at room temperature) on the C-face of SiC [SiC(000-1)] and show that carrie…
Although the corresponding carbon-metal interactions can be very different, a similar nonlinear growth behavior of graphene has been observed for different metal substrates. To understand this interesting experimental observation, a multiscale $\lq\lq$standing-on-the-front" kinetic Monte Carlo study is performed. An extraordinary robust geometry effect is identified, which solely determines the growth kinetics and makes the details of carbon-metal interaction not relevant at all. Based on such a geometry-determined mechanism, epitaxial growth behavior of graphene can be easily predicted in man…
Graphene outstanding properties directly come from its pecular electronic structure and thus from the honeycomb lattice symmetry. The way interaction with the substrate impact this lattice is of primary importance. This is peculiarly true for epitaxial graphene because of the SiC substrate. The advantage of this system that produces macroscopic samples in registry with a substrate could turn to a major drawback if the graphene lattice reveals to be strongly distorted. Extensive ab initio calculations supported by Scanning Tunneling Microscopy experiments, demonstrate here that the substrate in…
Graphene has been known for a long time but only recently has its potential for electronics been recognized. Its history is recalled starting from early graphene studies. A critical insight in June, 2001 brought to light that graphene could be used for electronics. This was followed by a series of proposals and measurements. The Georgia Institute of Technology (GIT) graphene electronics research project was first funded, by Intel in 2003, and later by the NSF in 2004 and the Keck foundation in 2008. The GIT group selected epitaxial graphene as the most viable route for graphene based electroni…
We investigate the fine structure of graphene on iridium, which is a model for graphene weakly interacting with a transition metal substrate. Even the highest quality epitaxial graphene displays tiny imperfections, i.e. small biaxial strains, ca. 0.3%, rotations, ca. 0.5^{\circ}, and shears over distances of ca. 100 nm, and is found incommensurate, as revealed by X-ray diffraction and scanning tunneling microscopy. These structural variations are mostly induced by the increase of the lattice parameter mismatch when cooling down the sample from the graphene preparation temperature to the measur…
Intercalation of atomic species through epitaxial graphene layers began only a few years following its initial report in 2004. The impact of intercalation on the electronic properties of the graphene is well known; however, the intercalant itself can also exhibit intriguing properties not found in nature. This suggests that a shift in the focus of epitaxial graphene intercalation studies may lead to fruitful exploration of many new forms of traditionally 3D materials. In the following forward-looking review, we summarize the primary techniques used to achieve and characterize EG intercalation,…
To determine the friction coefficient of graphene, micro-scale scratch tests are conducted on exfoliated and epitaxial graphene at ambient conditions. The experimental results show that the monolayer, bilayer, and trilayer graphene all yield friction coefficients of approximately 0.03. The friction coefficient of pristine graphene is less than that of disordered graphene, which is treated by oxygen plasma. Ramping force scratch tests are performed on graphene with various numbers of layers to determine the normal load required for the probe to penetrate graphene. A very low friction coefficien…
Graphene exhibits unconventional two-dimensional electronic properties resulting from the symmetry of its quasiparticles, which leads to the concepts of pseudospin and electronic chirality. Here we report that scanning tunneling microscopy can be used to probe these unique symmetry properties at the nanometer scale. They are reflected in the quantum interference pattern resulting from elastic scattering off impurities, and they can be directly read from its fast Fourier transform. Our data, complemented by theoretical calculations, demonstrate that the pseudospin and the electronic chirality i…
Local electronic structures of nanometer-sized patches of epitaxial graphene and its interface layer with SiC(0001) have been studied by atomically resolved scanning tunneling microscopy and spectroscopy. Localized states belonging to the interface layer of a graphene/SiC system show to have an essential influence on the electronic structure of graphene. Giant enhancement of inelastic tunneling, reaching 50% of the total tunneling current, has been observed at the localized states on a nanometer-sized graphene monolayer surrounded by defects.
We report the growth of high-quality triangular GaN nanomesas, 30-nm thick, on the C-face of 4H-SiC using nano selective area growth (NSAG) with patterned epitaxial graphene grown on SiC as an embedded mask. NSAG alleviates the problems of defective crystals in the heteroepitaxial growth of nitrides, and the high mobility graphene film can readily provide the back low-dissipative electrode in GaN-based optoelectronic devices. The process consists in first growing a 5-8 graphene layers film on the C-face of 4H- SiC by confinement-controlled sublimation of silicon carbide. The graphene film is t…
Graphene grown on Fe(110)by chemical vapor deposition using propylene is investigated by means of angle-resolved photoemission. The presence of massless Dirac fermions is clearly evidenced by the observation of a fully intact Dirac cone. Unlike Ni(111) and Co(0001), the Fe(110) imposes a strongly anisotropic quasi-one-dimensional structure on the graphene. Certain signatures of a superlattice effect appear in the dispersion of its σ-bands but the Dirac cone does not reveal any detectable superlattice or quantum-size effects although the graphene corrugation is twice as large as in the establis…
High-quality, large-area epitaxial graphene can be grown on metal surfaces but its transport properties cannot be exploited because the electrical conduction is dominated by the substrate. Here we insulate epitaxial graphene on Ru(0001) by a step-wise intercalation of silicon and oxygen, and the eventual formation of a SiO$_2$ layer between the graphene and the metal. We follow the reaction steps by x-ray photoemission spectroscopy and demonstrate the electrical insulation using a nano-scale multipoint probe technique.
Uniform single layer graphene was grown on single-crystal Ir films a few nanometers thick which were prepared by pulsed laser deposition on sapphire wafers. These graphene layers have a single crystallographic orientation and a very low density of defects, as shown by diffraction, scanning tunnelling microscopy, and Raman spectroscopy. Their structural quality is as high as that of graphene produced on Ir bulk single crystals, i.e. much higher than on metal thin films used so far.
We report a Raman study of the so-called buffer layer with $(6\sqrt3\times6\sqrt3)R30^{\circ}$ periodicity which forms the intrinsic interface structure between epitaxial graphene and SiC(0001). We show that this interface structure leads to a nonvanishing signal in the Raman spectrum at frequencies in the range of the D- and G-band of graphene and discuss its shape and intensity. Ab-initio phonon calculations reveal that these features can be attributed to the vibrational density of states of the buffer-layer.
Due to the predominantly surface character of graphene, it is highly suitable for functionalization with external atoms and/or molecules leading to a plethora of new and interesting phenomena. Here we show ferromagnetic properties of hydrogen-functionalized epitaxial graphene on SiC. Ferromagnetism in such a material is not directly evident as it is inherently composed of only non-magnetic constituents. Our results nevertheless show strong ferromagnetism, which cannot be explained by simple magnetic impurities. The ferromagnetism is unique to hydrogenated epitaxial graphene on SiC, where inter…
The quantum Hall effect, with a Berry's phase of $π$ is demonstrated here on a single graphene layer grown on the C-face of 4H silicon carbide. The mobility is $\sim$ 20,000 cm$^2$/V$\cdot$s at 4 K and ~15,000 cm$^2$/V$\cdot$s at 300 K despite contamination and substrate steps. This is comparable to the best exfoliated graphene flakes on SiO$_2$ and an order of magnitude larger than Si-face epitaxial graphene monolayers. These and other properties indicate that C-face epitaxial graphene is a viable platform for graphene-based electronics.
Heterostructures of Dirac materials such as graphene and topological insulators provide interesting platforms to explore exotic quantum states of electrons in solids. Here we study the electronic structure of graphene-Sb2Te3 heterostructure using density functional theory and tight-binding methods. We show that the epitaxial graphene on Sb2Te3 turns into quantum spin-Hall phase due to its proximity to the topological insulating Sb2Te3. It is found that the epitaxial graphene develops a giant spin-orbit gap of about ~20 meV, which is about three orders of magnitude larger than that of pristine …
The Kolbe electrochemical oxidation strategy has been utilized to achieve an efficient quasireversible electrochemical grafting of the alpha-naphthylmethyl functional group to graphene. The method facilitates reversible bandgap engineering in graphene and preparation of electrochemically erasable organic dielectric films. The picture shows Raman D-band maps of both systems.
