In this paper a conceptual overview is given of the software foreseen to configure the ATLAS trigger system. Two functional software prototypes have been developed to configure the ATLAS Level-1 emulation and the High-Level Trigger software. Emphasis has been put so far on following a consistent approach between the two trigger systems and on addressing their requirements, taking into account the specific use-case of the `Region-of-Interest' mechanism for the ATLAS Level-2 trigger. In the future the configuration of the two systems will be combined to ensure a consistent selection configuration for the entire ATLAS trigger system.
Due to the huge interaction rates and the tough experimental environment of pp collisions at a centre-of-mass energy sqrt(s)=14TeV and luminosities of up to 10^34 cm^-2 s^-1, one of the experimental challenges at the LHC is the triggering of interesting events. In the ATLAS experiment a three-level trigger system is foreseen for this purpose. The first-level trigger is implemented in custom hardware and has been designed to reduce the data rate from the initial bunch-crossing rate of 40 MHz to around 75 kHz. Its event selection is based on information from the calorimeters and dedicated muon d…
This article describes the design, testing and production of the ATLAS Region of Interest Builder (RoIB). This device acts as an interface between the Level 1 trigger and the high level trigger (HLT) farm for the ATLAS LHC detector. It distributes all of the level 1 data for a subset of events to a small number of (16 or less) individual commodity processors. These processors in turn provide this information to the HLT. This allows the HLT to use the level 1 information to narrow data requests to areas of the detector where level 1 has identified interesting objects.
The ATLAS detector at CERN's Large Hadron Collider will be exposed to proton-proton collisions from beams crossing at 40 MHz that have to be reduced to the few 100 Hz allowed by the storage systems. A three-level trigger system has been designed to achieve this goal. We describe the configuration system under construction for the ATLAS trigger chain. It provides the trigger system with all the parameters required for decision taking and to record its history. The same system configures the event reconstruction, Monte Carlo simulation and data analysis, and provides tools for accessing and mani…
The Trigger Data Serializer (TDS) is a custom ASIC designed for the upgrade of the innermost station of the endcap ATLAS Muon Spectrometer. It is a mixed-signal chip with two working modes that can handle up to 128 detector channels. A total of 6,000 TDS ASICs have been produced for detector operation. This paper discusses a custom automatic test platform we developed to provide quality control of the TDS ASICs. We introduce the design, test procedures, and results obtained from this TDS testing platform.
The ATLAS detector at CERN's Large Hadron Collider (LHC) will be exposed to proton-proton collisions from beams crossing at 40 MHz. At the design luminosity of 10^34 cm^-2 s^-1 there are on average 23 collisions per bunch crossing. A three-level trigger system will select potentially interesting events in order to reduce the read-out rate to about 200 Hz. The first trigger level is implemented in custom-built electronics and makes an initial fast selection based on detector data of coarse granularity. It has to reduce the rate by a factor of 10^4 to less than 100 kHz. The other two consecutive…
The small-strip Thin Gap Chamber (sTGC) will be used for both triggering and precision tracking purposes in the upgrade of the ATLAS forward muon spectrometer. Both sTGC pad and strip detectors are readout by a Trigger Data Serializer (TDS) ASIC in the trigger path. This ASIC has two operation modes to prepare trigger data from pad and strip detectors respectively. The pad mode (pad-TDS) collects the firing status for up to 104 pads from one detector layer and transmits the data at 4.8 Gbps to the pad trigger extractor every 25 ns. The pad trigger extractor collects pad-TDS data from eight det…
In this paper, we present the design and test results of LOCx2, a transmitter ASIC for the ATLAS Liquid Argon Calorimeter trigger upgrade. LOCx2 consists of two channels and each channel encodes ADC data with an overhead of 14.3% and transmits serial data at 5.12 Gbps with a latency of less than 27.2 ns. LOCx2 is fabricated with a commercial 0.25-um Silicon-on-Sapphire CMOS technology and is packaged in a 100-pin QFN package. The power consumption of LOCx2 is about 843 mW.
Two optical data link data transmission Application Specific Integrated Circuits (ASICs), the baseline and its backup, have been designed for the ATLAS Liquid Argon (LAr) Calorimeter Phase-I trigger upgrade. The latency of each ASIC and that of its corresponding receiver implemented in a back-end Field-Programmable Gate Array (FPGA) are critical specifications. In this paper, we present the latency measurements and simulation of two ASICs. The measurement results indicate that both ASICs achieve their design goals and meet the latency specifications. The consistency between the simulation and …
The ATLAS trigger has been used very successfully to collect collision data during 2009 and 2010 LHC running at centre of mass energies of 900 GeV, 2.36 TeV, and 7 TeV. This paper presents the ongoing work to commission the ATLAS trigger with proton collisions, including an overview of the performance of the trigger based on extensive online running. We describe how the trigger has evolved with increasing LHC luminosity and give a brief overview of plans for forthcoming LHC running.
The performance of the three-level ATLAS muon trigger as evaluated by using LHC data is presented. Events have been selected by using only the hardware-based Level-1 trigger in order to commission and to subsequently enable the (software-based) selections of the High Level Trigger. Studies aiming at selecting prompt muons from J/ψ and at reducing non prompt muon contamination have been performed. A brief overview on how the muon triggers evolve with increasing luminosity is given.
An extensive system test of the ATLAS muon spectrometer has been performed in the H8 beam line at the CERN SPS during the last four years. This spectrometer will use pressurized Monitored Drift Tube (MDT) chambers and Cathode Strip Chambers (CSC) for precision tracking, Resistive Plate Chambers (RPCs) for triggering in the barrel and Thin Gap Chambers (TGCs) for triggering in the end-cap region. The test set-up emulates one projective tower of the barrel (six MDT chambers and six RPCs) and one end-cap octant (six MDT chambers, A CSC and three TGCs). The barrel and end-cap stands have also been…
Many models for physics Beyond the Standard Model predict an increased production rate of tau leptons. Therefore hadronically decaying tau leptons play an important role in searches for new physics at the LHC. By triggering on them, the discovery power of ATLAS can be greatly enhanced for many Beyond the Standard Model searches. In this contribution we present a brief description of the ATLAS tau trigger system and demonstrate its robustness and reliability during 2011.
The ATLAS experiment at the Large Hadron Collider employs a two-level trigger system to record data at an average rate of 1 kHz from physics collisions, starting from an initial bunch crossing rate of 40 MHz. During the LHC Run 2 (2015-2018), the ATLAS trigger system operated successfully with excellent performance and flexibility by adapting to the various run conditions encountered and has been vital for the ATLAS Run-2 physics programme. For proton-proton running, approximately 1500 individual event selections were included in a trigger menu which specified the physics signatures and select…
The ATLAS experiment at the Large Hadron Collider (LHC) will face the challenge of efficiently selecting interesting candidate events in $pp$ collisions at 14 TeV centre-of-mass energy, whilst rejecting the enormous number of background events. Therefore it is equipped with a three level trigger system. The first level is is hardware based and uses coarse granularity calorimeter information and fast readout muon chambers. The second and third level triggers, which are software based, will need to reduce the first level trigger output rate of ~ 75 kHz to ~ 200 Hz written out to mass storage. Th…
In this work several aspects of ATLAS RPC offline monitoring and data quality assessment are illustrated with cosmics data selected by RPC trigger. These correspond to trigger selection, front-end mapping, detection efficiency and occupancy, which are studied in terms of low level quantities such as: RPC off-line hits and standalone tracks. The tools and techniques presented are also extended to the forthcoming LHC p-p beam collisions.
The upgrade to the ATLAS trigger for LHC Run 2 is presented including a description of the design and performance of the newly reimplemented tracking algorithms. The profiling infrastructure, constructed to provide prompt feedback from the optimisation procedure is described including the methods used to monitor the relative performance improvements as the code evolves. The performance of the trigger on the first data collected in the LHC Run 2 is presented.
The ATLAS detector at CERN's Large Hadron Collider will be exposed to proton-proton collisions from beams crossing at 40 MHz. A three-level trigger system was designed to select potentially interesting events and reduce the incoming rate to 100-200 Hz. The first trigger level (LVL1) is implemented in custom-built electronics, the second and third trigger levels are realized in software. Based on calorimeter information and hits in dedicated muon-trigger detectors, the LVL1 decision is made by the central-trigger processor yielding an output rate of less than 100 kHz. The allowed latency for th…
For Run 3 (from 2021), the LHC will undergo a significant increase in instantaneous luminosity to 1.5 times its current value which will lead to larger collected statistics and an enhanced sensitivity to new physics. The Phase-1 upgrade of the ATLAS Level-1 endcap muon trigger is essential to keep the physics acceptance at Run 3. A new trigger logic to take coincidence with detectors inside and outside the magnetic field is described and is shown to reduce the trigger rate to lower than the required level in Run 3. A new trigger board, NSL, to integrate all the information from various detecto…
The innermost station of the present ATLAS forward muon detector needs to be upgraded for the super-LHC. We present a proposal to replace it with a sandwiched detector composed of several layers of small-radius Monitored Drift Tube chambers (sMDT) for precision tracking measurement and two stations of multi-gap Resistive Plate Chambers (mRPC) for triggering purpose. We describe the layout of the upgraded detector and the trigger strategy. Several modifications to the RPCs used in the ATLAS barrel region are needed to satisfy the super-LHC requirements. Various studies with the proposed mRPC ti…
This paper presents several component prototypes towards a low-latency, small-form-factor optical link designed for the ATLAS Liquid Argon Calorimeter Phase-I trigger upgrade. A prototype of the custom-made dual-channel optical transmitter module, the Miniature optical Transmitter (MTx), with separate transmitter optical sub-assemblies (TOSAs) has been demonstrated at data rates up to 8 Gbps per channel. A Vertical-Cavity Surface-Emitting Laser (VCSEL) driver ASIC has been developed and is used in the current MTx prototypes. A serializer ASIC prototype, operating at up to 8 Gbps per channel, h…
Electron and photon triggers covering transverse energies from 5 GeV to several TeV are essential for signal selection in a wide variety of ATLAS physics analyses to study Standard Model processes and to search for new phenomena. Final states including leptons and photons had, for example, an important role in the discovery and measurement of the Higgs particle. Dedicated triggers are also used to collect data for calibration, efficiency and fake rate measurements. The ATLAS trigger system is divided in a hardware-based (Level 1) and a software based High-Level Trigger (HLT), both of which wer…
Highly selective triggers are essential for the physics programme of the ATLAS experiment at HL-LHC where the instantaneous luminosity will be about an order of magnitude larger than the LHC instantaneous luminosity in Run 1. The first level muon trigger rate is dominated by low momentum muons below the nominal trigger threshold due to the moderate momentum resolution of the Resistive Plate and Thin Gap trigger chambers. The resulting high trigger rates at HL-LHC can be sufficiently reduced by using the data of the precision Muon Drift Tube chambers for the trigger decision. This requires the …
The PreProcessor of the ATLAS Level-1 Calorimeter Trigger prepares the analogue trigger signals sent from the ATLAS calorimeters by digitising, synchronising, and calibrating them to reconstruct transverse energy deposits, which are then used in further processing to identify event features. During the first long shutdown of the LHC from 2013 to 2014, the central components of the PreProcessor, the Multichip Modules, were replaced by upgraded versions that feature modern ADC and FPGA technology to ensure optimal performance in the high pile-up environment of LHC Run 2. This paper describes the…
The Pad Front End Board (pFEB) and the Strip Front End Board (sFEB) are developed for the ATLAS Phase-I sTGC Trigger Upgrade. The pFEB is used to to gather and analyze pads trigger, and the sFEB is developed to accept the pad trigger to define the regions-of-interest for strips readout. The performance of p/sFEBs must be confirmed before they are mounted on the sTGC detector. We will present the scanning test system prototype which is designed according to the test requirements of the p/sFEB. In this test system prototype, a simulation signal board is developed to generate different types of s…
The High-Luminosity LHC (HL-LHC) will provide the unique opportunity to explore the nature of physics beyond the Standard Model of strong and electroweak interactions. Highly selective first-level triggers are essential for the physics programme of the ATLAS experiment at HL-LHC, where the instantaneous luminosity will exceed the instantaneous LHC Run 1 luminosity by about an order of magnitude. The ATLAS first-level muon trigger rate is dominated by low momentum muons, which are accepted because of the moderate momentum resolution of the RPC and TGC trigger chambers. This limitation can be ov…
A study of the performance of the ATLAS tau and missing energy triggers with data collected in spring 2010 at {\surd}s = 7 TeV proton-proton collisions at the Large Hadron Collider (LHC) is presented. A comparison was performed between data and Monte Carlo simulations for the tau and missing transverse energy triggers. As well as a comparison between missing transverse energy trigger quantities and their offline reconstructed counterparts. Tau trigger results compare well with predictions from Monte Carlo simulations. Slight deviations are observed for tau shower shape quantities. Possible sou…
Since the start-up of the LHC end of 2009, the trigger commissioning is in full swing. The ATLAS trigger system is divided into three levels: the hardware-based first level trigger, and the software-based second level trigger and Event Filter, collectively referred to as the High Level Trigger (HLT). Initially, events have been selected online based on the Level-1 selections with the HLT algorithms run but not rejecting any events. This has been an important step in the commissioning of these triggers to ensure their correct functioning and subsequently to enable the HLT selections. Due to inc…
Physics collisions at 13 TeV are expected at the LHC with an average of 40-50 proton-proton collisions per bunch crossing under nominal conditions. Tracking at trigger level is an essential tool to control the rate in high-pileup conditions while maintaining a good efficiency for relevant physics processes. The Fast TracKer is an integral part of the trigger upgrade for the ATLAS detector. For every event passing the Level-1 trigger (at a maximum rate of 100 kHz) the FTK receives data from all the channels of the silicon detectors, providing tracking information to the High Level Trigger in or…
A radiation-hard quad-channel 12-bit 40 MSPS pipeline analog-to-digital converter (ADC) has been designed for the trigger readout electronics Phase-I upgrade of the ATLAS Liquid Argon calorimeter, at the CERN Large Hadron Collider. The final version of the custom design, fabricated in a commercial 130 nm CMOS process, is presented and found to meet the system requirements for analog performance and radiation tolerance. The procedure for quality control of 17200 ADCs is described and the results are presented.
The outer shell of the ATLAS experiment at the LHC consists of a system of toroidal air-core magnets in order to allow for the precise measurement of the transverse momentum p$_T$ of muons, which in many physics channels are a signature of interesting physics processes. For the precise determination of the muon momentum Monitored Drift Tube chambers (MDT) with high position accuracy are used, while for the fast identification of muon tracks chambers with high time resolution are used, able to select muons above a predefined p$_T$ threshold for use in the first Level of the ATLAS triggering sys…
The ATLAS experiment at the Large Hadron Collider (LHC) employs a trigger system consisting of a first-level hardware trigger (L1) and a software-based high-level trigger. The L1 muon trigger system selects muon candidates, assigns them to the correct LHC bunch crossing and classifies them into one of six transverse-momentum threshold classes. The L1 muon trigger system uses resistive-plate chambers (RPCs) to generate the muon-induced trigger signals in the central (barrel) region of the ATLAS detector. The ATLAS RPCs are arranged in six concentric layers and operate in a toroidal magnetic fie…
The ATLAS phase-I upgrade aims to enhance event trigger performance in the Liquid Argon (LAr) calorimeter and the forward muon spectrometer. The trigger signals are transmitted by optical transceivers at 5.12 Gbps per channel in a radiation field. We report the design, quality control in production and ageing test of the transceivers fabricated with the LOCld laser driver and multi-mode 850 nm vertical-cavity surface-emitting laser (VCSEL). The modules are packaged in miniature formats of dual-channel transmitter (MTx) and transceiver (MTRx) for the LAr. The transmitters are also packaged in s…
The trigger selection capabilities of the ATLAS detector have been significantly enhanced for the LHC Run- 2 in order to cope with the higher event rates and with the large number of simultaneous interactions (pile-up) per protonproton bunch crossing. A new hardware system, designed to analyse real time event-topologies at Level-1 came to full use in 2017. A hardware-based track reconstruction system, expected to be used real-time in 2018, is designed to provide track information to the high-level software trigger at its full input rate. The high-level trigger selections are largely relying on…
A Liquid-argon Trigger Digitizer Board (LTDB) is being developed to upgrade the ATLAS Liquid Argon Calorimeter Phase-I trigger electronics. The LTDB located at the front end needs to obtain the clock signals and be configured and monitored remotely from the back end. A clock and control system is being developed for the LTDB and the major functions of the system have been evaluated. The design and evaluation of the clock and control system are presented in this paper.
ATLAS detector at the LHC will undergo a major Phase-II upgrade for the High Luminosity LHC. The upgrade affects all major ATLAS systems, including the Trigger and Data Acquisition systems. As part of the Level-0 Trigger System, the Global Trigger uses full-granularity calorimeter cells to perform algorithms, refines the trigger objects and applies topological requirements. The Global Trigger uses a Global Common Module as the building block of its design. To achieve a high input and output bandwidth and substantial processing power, the Global Common Module will host the most advanced FPGAs a…
The main results of the quality assurance tests performed on the Resistive Plate Chamber used by the ATLAS experiment at LHC as muon trigger chambers are reported and discussed. Since July 2004, about 270 RPC units has been certified at INFN Lecce site and delivered to CERN, for being integrated in the final muon station of the ATLAS barrel region. We show the key RPC characteristics which qualify the performance of this detector technology as muon trigger chamber in the harsh LHC enviroments. These are dark current, chamber efficiency, noise rate, gas volume tomography, and gas leakage.
The LHC upgrade is planned to enhance the instantaneous luminosity during Run 3 from 2021 through 2023. The Phase-I upgrade of the trigger readout electronics for the ATLAS Liquid Argon (LAr) Calorimeters will be installed during the second long shutdown of LHC in 2019-2020. In this upgrade, the so-called super cells are introduced to provide higher granularity, higher resolution and longitudinal shower shape information from the LAr calorimeters to the level-1 trigger processors. A new LAr Trigger Digitizer Board (LTDB) will manipulate and digitize 320 channels of super cell signals, and tran…
This paper reports on the development of a resource-efficient FPGA-based neural network regression model for potential applications in the future hardware muon trigger system of the ATLAS experiment at the Large Hadron Collider (LHC). Effective real-time selection of muon candidates is the cornerstone of the ATLAS physics programme. With the planned ATLAS upgrades for the High Luminosity LHC, an entirely new FPGA-based hardware muon trigger system will be installed that will process full muon detector data within a 10 $μs$ latency window. The large FPGA devices planned for this upgrade should …
After the current shutdown, the LHC is about to resume operation for a new data-taking period, when it will operate with increased luminosity, event rate and center of mass energy. The new conditions will impose more demanding constraints on the ATLAS online trigger reconstruction and selection system. To cope with such increased constraints, the ATLAS High-Level Trigger, placed after a first hardware-based Level 1 trigger, has been redesigned by merging two previously separated software-based processing levels. In the new joint processing level, the algorithms run in the same computing nodes,…
Highly selective first-level triggers are essential to exploit the full physics potential of the ATLAS experiment at High-Luminosity LHC (HL-LHC). The concept for a new muon trigger stage using the precision monitored drift tube (MDT) chambers to significantly improve the selectivity of the first-level muon trigger is presented. It is based on fast track reconstruction in all three layers of the existing MDT chambers, made possible by an extension of the first-level trigger latency to six microseconds and a new MDT read-out electronics required for the higher overall trigger rates at the HL-LH…
The performance of the ATLAS muon trigger system is evaluated with proton-proton ($pp$) and heavy-ion (HI) collision data collected in Run 2 during 2015-2018 at the Large Hadron Collider. It is primarily evaluated using events containing a pair of muons from the decay of $Z$ bosons to cover the intermediate momentum range between 25 GeV and 100 GeV. Overall, the efficiency of the single-muon triggers is about 68 % in the barrel region and 85% in the endcap region. The $p_{\text{T}}$ range for efficiency determination is extended by using muons from decays of $J/ψ$ mesons, $W$ bosons, and top q…
The LHC is expected to increase its center-of-mass energy from 13 TeV to 14 TeV for Run 3 scheduled from 2022 to 2024. After Run 3, upgrades for the High-Luminosity-LHC (HL-LHC) programme are planned and the operation will start in 2027, increasing the instantaneous luminosity to 5.0 -- 7.5 times its nominal luminosity. Continuous upgrades of the ATLAS trigger system are planned to cope with the high event rate and to keep the physics acceptance. During the long shutdown period before Run 3, new detectors will be installed to improve the trigger performance. New trigger logic, combining inform…
The High-Luminosity LHC will provide the unique opportunity to explore the nature of physics beyond the Standard Model of strong and electroweak interactions. Highly selective first level triggers are essential for the physics programme of the ATLAS experiment at the HL-LHC where the instantaneous luminosity will exceed the LHC Run 1 instantaneous luminosity by almost an order of magnitude. The ATLAS first level muon trigger rate is dominated by low momentum muons, selected due to the moderate momentum resolution of the resistive plate and thin gap trigger chambers. This limitation can be over…
The Level-1 Muon Barrel Trigger of the ATLAS Experiment at LHC makes use of Resistive Plate Chamber (RPC) detectors. The on-detector trigger electronics modules are able to identify muons with predefined transverse momentum values (pT) by executing a coincidence logic on signals coming from the various detector layers. Then, on-detector trigger boards transfer trigger data to the off-detector electronics. A complex trigger system processes the incoming data by combining trigger information from the Barrel and the End-cap regions, and by providing the combined muon candidate to the Central Trig…
A new Muon-to-Central-Trigger Processor Interface (MUCTPI) was built as part of the upgrade of the ATLAS Level-1 trigger system for the next Run of the Large Hadron Collider at CERN. The MUCTPI has 208 high-speed optical serial links for receiving muon candidates from the muon trigger detectors. Three high-end FPGAs are used for real-time processing of the muon candidates, for sending trigger information to other parts of the trigger system, and for sending summary information to the data acquisition and monitoring system. A System-on-Chip (SoC) is used for the control, configuration and monit…
We propose a new fixed latency scheme for Xilinx gigabit transceivers that will be used in the upgrade of the ATLAS forward muon spectrometer at the Large Hadron Collider. The fixed latency scheme is implemented in a 4.8 Gbps link between a frontend data serializer ASIC and a packet router. To achieve fixed latency, we use IO delay and dedicated carry in resources in a Xilinx FPGA, while minimally relying on the embedded features of the FPGA transceivers. The scheme is protocol independent and can be adapted to FPGA from other vendors with similar resources. This paper presents a detailed impl…
ATLAS-SCT has developed a new ATLAS trigger card, 'Digital Atlas Vme Electronics' ("DAVE"). The unit is designed to provide a versatile array of interface and logic resources, including a large FPGA. It interfaces to both VME bus and USB hosts. DAVE aims to provide exact ATLAS CTP (ATLAS Central Trigger Processor) functionality, with random trigger, simple and complex deadtime, ECR (Event Counter Reset), BCR (Bunch Counter Reset) etc. being generated to give exactly the same conditions in standalone running as experienced in combined runs. DAVE provides additional hardware and a large amount o…
The Large Hadron Collider (LHC) at CERN plans to have a series of upgrades to increase its instantaneous luminosity to 7.5 the nominal luminosity. The increased luminosity drastically impacts the ATLAS trigger and readout data rates. The inner-most station of the ATLAS muon spectrometer, the so-called Small Wheels is being replaced with a New Small Wheel (NSW) system, consisting of Micromegas and small-strip Thin Gap Chambers (sTGC) detectors. The on-detector radiation levels required radiation tolerant electronics. The lower radiation levels on the rim of the NSW allowed utilizing commercial …
During the next major shutdown (2019-2020), the ATLAS experiment at the LHC will adopt the Front-End Link eXchange (FELIX) system as the interface between the data acquisition, detector control and TTC (Timing, Trigger and Control) systems and new or updated trigger and detector front-end electronics. FELIX will function as a router between custom serial links from front-end ASICs and FPGAs to data collection and processing components via a commodity switched network. Links may aggregate many slower links or be a single high bandwidth link. FELIX will also forward the LHC bunch-crossing clock,…
The ATLAS detector at LHC will require a Trigger system to efficiently select events down to a manageable event storage rate of about 400 Hz. By 2015 the LHC instantaneous luminosity will be increased up to 3 x 10^34 cm-2s-1, this represents an unprecedented challenge faced by the ATLAS Trigger system. To cope with the higher event rate and efficiently select relevant events from a physics point of view, a new element will be included in the Level-1 Trigger scheme after 2015: the Topological Processor (L1Topo). The L1Topo system, currently developed at CERN, will consist initially of an ATCA c…
Hardware-based track reconstruction in the CMS and ATLAS trigger systems for the High-Luminosity LHC upgrade will provide unique capabilities. An overview is presented of earlier track trigger systems at hadron colliders, in particular for the Tevatron CDF and D0 experiments. We discuss the plans of the CMS and ATLAS experiments to implement hardware-based track reconstruction for the High-Luminosity LHC. Particular focus is placed on the track trigger capability of the upgraded CMS experiment. We discuss the challenges and opportunities of this novel handle, and review the alternatives that w…
The ATLAS experiment at the Large Hadron Collider (LHC) at CERN is currently waiting to record the first collision data in spring 2009. Its muon spectrometer is designed to achieve a momentum resolution of 10% pT(mu) = 1 TeV/c. The spectrometer consists of a system of three superconducting air-core toroid magnets and is instrumented with three layers of Monitored Drift Tube chambers (Cathode Strip Chambers in the extreme forward region) as precision detectors. Resistive Plate Chambers in the barrel and Thin Gap Chambers in the endcap regions provide a fast trigger system. The spectrometer pass…
The Fast Tracker (FTK) is a proposed upgrade to the ATLAS trigger system that will operate at full Level-1 output rates and provide high quality tracks reconstructed over the entire detector by the start of processing in Level-2. FTK solves the combinatorial challenge inherent to tracking by exploiting the massive parallelism of Associative Memories (AM) that can compare inner detector hits to millions of pre-calculated patterns simultaneously. The tracking problem within matched patterns is further simplified by using pre-computed linearized fitting constants and leveraging fast DSP's in mode…
The DataFlow is sub-system of the ATLAS data acquisition responsible for the reception, buffering and subsequent movement of partial and full event data to the higher level triggers: Level 2 and Event Filter. The design of the software is based on OO methodology and its implementation relies heavily on the use of posix threads and the Standard Template Library. This article presents our experience with Linux, posix threads and the Standard Template Library in the real time environment of the ATLAS data flow.
The Tile Calorimeter (TileCal) is the hadronic calorimeter covering the central region of the ATLAS detector at the LHC. It is a sampling calorimeter consisting of alternating thin steel plates and scintillating tiles. Wavelength shifting fibers coupled to the tiles collect the produced light and are read out by photomultiplier tubes. Currently, an analog sum of the processed signal of several photomultipliers serves as input to the first level of trigger. Photomultiplier signals are then digitized and stored on detector and are only transferred off detector once the first trigger acceptance h…
The FEB(front end board) configuration test board is developed aiming at meeting the requirement of testing the new generation ASIC(application-specific integrated circuit) chips and its configuration system for ATLAS NSW(New Small Wheel) upgrade, In this paper, some functions are developed in terms of the configurations of the key chips on the FEB, VMM3 and TDS2 using GBT-SCA. Additionally, a flexible communication protocol is designed, verifying the whole data link. It provides technical reference for prototype FEB key chip configuration and data readout, as well as the final system configur…
Thin gap chambers (TGCs) are used for the muon trigger system in the forward region of the LHC experiment ATLAS. The TGCs are expected to provide a trigger signal within 25 ns of the bunch spacing. An extensive system test of the ATLAS muon spectrometer has been performed in the H8 beam line at the CERN SPS during the last few years. A relational database was used for storing the conditions of the tests as well as the configuration of the system. This database has provided the detector control system with the information needed for configuration of the front end electronics. The database is us…
