An analysis of the influence of the high-frequency electromagnetic field on the amplitude-frequency and signal characteristics of RF SQUID and experimental verification are carried out. At low parameter , the RF SQUID behavior is well described analytically by the theoretical model. In experiment, basic operation scheme is used in which the interferometer is inductively connected to a resonant tank circuit driven by RF current at a frequency close to the resonance frequency of the tank. It is shown that parameter , which distinguishes between hysteretic and non-hysteretic regimes, can be effectively adjusted to a desired value by applying the high-frequency field of a certain amplitude and frequency much higher than tank resonant frequency. A significant increase in the conversion factor and sensitivity of the RF SQUID during this adjustment is discussed.
This paper presents the analytical and numerical analysis of fluctuational dynamics of ac hysteretic SQUID. It has been demonstrated, that the most important parameter for the improvement of the hysteretic SQUID sensitivity is the ratio between the pump and the characteristic frequencies but not their absolute values. The resonant behavior of signal-to-noise ratio as function of the pump frequency has been observed and the narrow area for the optimal pump frequency range is indicated.
We present a theoretical study on the dynamical properties of three-dimensional arrays of Josephson junctions. Our results indicate that such superconducting networks represent highly sensitive 3D-SQUIDs having some major advantages in comparison with conventional planar SQUIDs. The voltage response function of 3D-SQUIDs is directly related to the vector-character of external electromagnetic fields. The theory developed here allows the three-dimensional reconstruction of a detected external field including phase information about the field variables. Applications include the design of novel ma…
A quantum system comprising of a monochromatic electromagnetic field coupled to a SQUID ring with sinusoidal non-linearity, is studied. A magnetostatic flux $Φ_{x}$ is also threading the SQUID ring, and is used to control the coupling between the two systems. It is shown that for special values of $Φ_{x}$ the system is strongly coupled. The time evolution of the system is studied. It is shown that exchange of energy takes place between the two modes and that the system becomes entangled. A second quasi-classical model that treats the electromagnetic field classically is also studied. A compari…
We present solutions of the time dependent Schrodinger equation for a SQUID ring coupled to an electromagnetic field, both treated quantum mechanically. We that show the SQUID ring can be used to create a maximally entangled state with the em field that without dissipation remains constant in time. Using methods familiar in quantum optics, we extend the model to include the effects of coupling this system to a dissipative environment. With this model we show that although such an environment makes a noticeable difference to the time evolution of the system, it need not destroy the the entangle…
We consider the interaction of a quantum mechanical SQUID ring with a classical resonator (a parallel $LC$ tank circuit). In our model we assume that the evolution of the ring maintains its quantum mechanical nature, even though the circuit to which it is coupled is treated classically. We show that when the SQUID ring is driven by a classical monochromatic microwave source, energy can be transferred between this input and the tank circuit, even when the frequency ratio between them is very large. Essentially, these calculations deal with the coupling between a single macroscopic quantum objec…
We used low-temperature scanning electron microscopy (LTSEM) for imaging quantized magnetic flux (vortices) in direct current (dc) superconducting quantum interference devices (SQUIDs) with approximately 1 micron spatial resolution at temperature T=77 K in a controllable magnetic field up to 20 microTesla. We demonstrate that LTSEM allows to image the spatial distribution of vortices in a YBa2Cu3O7/SrTiO3/YBa2Cu3O7 multilayer thin-film structure consisting of a dc SQUID washer with an integrated input coil on top. Simultaneously, we are able to measure the low-frequency noise of the sample und…
In this paper we investigate the behaviour of a fully quantum mechanical system consisting of a mesoscopic SQUID ring coupled to one or two electromagnetic field modes. We show that we can use a static magnetic flux threading the SQUID ring to control the transfer of energy, the entanglement and the statistical properties of the fields coupled to the ring. We also demonstrate that at, and around, certain values of static flux the effective coupling between the components of the system is large. The position of these regions in static flux is dependent on the energy level structure of the ring …
In this paper we present experimental data on the frequency domain response of a SQUID ring (a Josephson weak link enclosed by a thick superconducting ring) coupled to a radio frequency (rf) tank circuit resonator. We show that with the ring weakly hysteretic the resonance lineshape of this coupled system can display opposed fold bifurcations that appear to touch (pinch off). We demonstrate that for appropriate circuit parameters these pinch off lineshapes exist as solutions of the non-linear equations of motion for the system.
The response of nonlinear metamaterials and superconducting electronics to two-tone excitation is critical for understanding their use as low-noise amplifiers and tunable filters. A new setting for such studies is that of metamaterials made of radio frequency superconducting quantum interference devices (rf-SQUIDs). The two-tone response of self-resonant rf-SQUID meta-atoms and metamaterials is studied here via intermodulation (IM) measurement over a broad range of tone frequencies and tone powers. A sharp onset followed by a surprising strongly suppressed IM region near the resonance is obser…
The peculiarities of the microstrip-DC SQUID amplifier caused by the resonant structure of the input circuit are analyzed. It is shown that the mutual inductance, that couples the input circuit and the SQUID loop, depends on the frequency of electromagnetic field. The renormalization of the SQUID parameters due to the screening effect of the input circuit vanishes when the Josephson frequency is much greater than the signal frequency.
We present a hybrid microwave SQUID multiplexer that combines two frequency-division multiplexing techniques to allow multiplexing a given number of cryogenic detectors with only a fraction of frequency encoding resonators. Similar to conventional microwave SQUID multiplexing, our multiplexer relies on inductively coupling non-hysteretic, unshunted rf-SQUIDs to superconducting microwave resonators as well as applying flux ramp modulation for output signal linearization. However, instead of utilizing one resonator per SQUID, we couple multiple SQUIDs to a common readout resonator and encode the…
We use low-temperature scanning electron microscopy combined with SQUID detection of magnetic flux to image vortices and to investigate low-frequency flux noise in YBa$_2$Cu$_3$O$_7$ thin film SQUIDs. The low-frequency flux noise shows a nonlinear increase with magnetic cooling field up to 60 $μ$T. This effect is explained by the surface potential barrier at the SQUID hole. By correlating flux noise data with the spatial distribution of vortices, we obtain information on spatial fluctuations of vortices on a microscopic scale, e.g. an average vortex hopping length of approximately 10 nm.
We investigate 3-junction SQUIDs which show voltage rectification if biased with an ac current drive with zero mean value. The Josephson phase across the SQUID experiences an effective ratchet potential, and the device acts as an efficient rocking ratchet, as demonstrated experimentally for adiabatic and nonadiabatic drive frequencies. For high-frequency drives the rectified voltage is quantized due to synchronization of the phase dynamics with the external drive. The experimental data are in excellent agreement with numerical simulations including thermal fluctuations.
We present a MHz frequency-division dc-SQUID multiplexer that is based on flux ramp modulation and a series array of $N$ identical current-sensing dc-SQUIDs with tightly coupled input coil. By running a periodic, sawtooth-shaped current signal through an additional modulation coil being tightly, but non-uniformly coupled to the individual SQUIDs, the voltage drop across the array changes according to the superposition of the flux-to-voltage characteristics of the individual SQUIDs within each cycle of the modulation signal. In this mode of operation, an input signal injected in the input coil …
The Cooper pair box qubit of SQUID configuration enables the readout of the qubit states by probing the effective Josephson inductance of the SQUID. This is realized by coupling the qubit to a tank circuit which induces a small alternating supercurrent in the SQUID loop. The effect of a small (but finite) geometrical inductance of the loop on the eigenstates of the system is figured out. The effect of qubit dephasing due to quadratic coupling to the tank circuit is evaluated. It is shown that the rate of dephasing in the vicinity of the magic points is relatively low unless the Josephson junct…
It is shown how the static and dynamic electromagnetic properties can be calculated for thin flat superconducting films of any shape and size, also multiply connected as used for SQUIDs, and for any value of the effective magnetic London penetration depth Lambda. As examples, the distributions of sheet current and magnetic field are obtained for rectangular and circular films without and with slits and holes, in response to an applied perpendicular magnetic field and to magnetic vortices moving in the film. The self energy and interaction of vortices with each other and with an applied magneti…
We investigate the transient dynamics of a lumped-element oscillator based on a dc superconducting quantum interference device (SQUID). The SQUID is shunted with a capacitor forming a nonlinear oscillator with resonance frequency in the range of several GHz. The resonance frequency is varied by tuning the Josephson inductance of the SQUID with on-chip flux lines. We report measurements of decaying oscillations in the time domain following a brief excitation with a microwave pulse. The nonlinearity of the SQUID oscillator is probed by observing the ringdown response for different excitation amp…
We investigate rf SQUIDs (Superconducting QUantum Interference Devices), coupled to a resonant input circuit, a readout tank circuit and a preamplifier, by numerically solving the corresponding Langevin equations and optimizing model parameters with respect to noise temperature. We also give approximate analytic solutions for the noise temperature, which we reduce to parameters of the SQUID and the tank circuit in the absence of the input circuit. The analytic solutions agree with numerical simulations of the full circuit to within 10%, and are similar to expressions used to calculate the nois…
Using superconducting quantum interference devices (SQUIDs) as basic, low-loss elements of thin-film metamaterials has one main advantage: Their resonance frequency is easily tunable by applying a weak magnetic field. The downside, however, is a strong sensitivity to stray and inhomogeneous magnetic fields. In this work, we demonstrate that even small magnetic fields from electronic components destroy the collective, resonant behaviour of the SQUID metamaterial. We also show how the effect of these fields can be minimized. As a first step, magnetic shielding decreases any initially present fie…
We study decoherence effects in a dc SQUID phase qubit caused by an isolation circuit with a resonant frequency. The coupling between the SQUID phase qubit and its environment is modeled via the Caldeira-Leggett formulation of quantum dissipation/coherence, where the spectral density of the environment is related to the admittance of the isolation circuit. When the frequency of the qubit is at least two times larger than the resonance frequency of the isolation circuit, we find that the decoherence time of the qubit is two orders of magnitude larger than the typical ohmic regime, where the fre…
In this paper we show that the radio frequency (rf) dynamical characteristics of a very strongly hysteretic SQUID ring, coupled to an rf tank circuit resonator, display relaxation oscillations. We demonstrate that the the overall form of these characteristics, together with the relaxation oscillations, can be modelled accurately by solving the quasi-classical non-linear equations of motion for the system. We suggest that in these very strongly hysteretic regimes SQUID ring-resonator systems may find application in novel logic and memory devices.
In the customary mode of operation of a SQUID, the electromagnetic field in the SQUID is an oscillatory function of time. In this situation, electromagnetic radiation is emitted, and couples to the sample. This is a back-action that can alter the state that we intend to measure. A circuit that could perform as a stationary SQUID consists of a loop of superconducting material that encloses the magnetic flux, connected to a superconducting and to a normal electrode. This circuit does not contain Josephson junctions, or any other miniature feature. We study the evolution of the order parameter an…
Scanning Superconducting Quantum Interference Device (SQUID) Susceptometry simultaneously images the local magnetic fields and susceptibilities above a sample with sub-micron spatial resolution. Further development of this technique requires a thorough understanding of the current, voltage, and flux characteristics of scanning SQUID susceptometers. These sensors often have striking anomalies in their current-voltage characteristics, which we believe to be due to electromagnetic resonances. The effect of these resonances on the performance of these SQUIDs is unknown. To explore the origin and i…
SQUID systems for ultra-low-field magnetic resonance (ULF MR) feature superconducting pick-up coils which must tolerate exposure to pulsed fields of up to 100 mT. Using type-II superconductor niobium (Nb) field distortions due to trapped vortices in the wire result. In addition, their rearrangement after quick removal of the pulsed field leads to excess low frequency noise which limits the signal-to-noise ratio. In contrast, type I superconductors, such as lead (Pb), do not exhibit vortices but form an intermediate state with the coexistence of normal and superconducting domains. We measured t…
Compact microwave resonantors made of superconducting rings containing Josephson junctions (SQUIDs) are attractive candidates for building frequency tunable metamaterials with low losses and pronounced nonlinear properties. We explore the nonlinearity of a SQUID metamaterial by performing a two-tone resonant spectroscopy. The small-amplitude response of the metamaterial under strong driving by a microwave pump tone is investigated experimentally and theoretically. The transmission coefficient $S_{21}$ of a weak probe signal is measured in the presence of the pump tone. Increasing the power of …
We present a readout method for superconducting flux qubits. The qubit quantum flux state can be measured by determining the Josephson inductance of an inductively coupled DC superconducting quantum interference device (DC-SQUID). We determine the response function of the DC-SQUID and its back-action on the qubit during measurement. Due to driving, the qubit energy relaxation rate depends on the spectral density of the measurement circuit noise at sum and difference frequencies of the qubit Larmor frequency and SQUID driving frequency. The qubit dephasing rate is proportional to the spectral d…
We present a new theoretical framework to analyze microwave amplifiers based on the dc SQUID. Our analysis applies input-output theory generalized for Josephson junction devices biased in the running state. Using this approach we express the high frequency dynamics of the SQUID as a scattering between the participating modes. This enables us to elucidate the inherently nonreciprocal nature of gain as a function of bias current and input frequency. This method can, in principle, accommodate an arbitrary number of Josephson harmonics generated in the running state of the junction. We report deta…
Results of magnetic force microscopy (MFM), dc SQUID magnetization, reversed Josephson effect (RJE), and resistance measurements in thin carbon arc (CA) films are presented. The observation of a RJE induced voltage as well as its rf frequency, input amplitude, and temperature dependence reveals the existence of Josephson Junction arrays. Oscillating behavior of the DC SQUID magnetization reminiscent of the Fraunhofer-like behavior of superconducting (SC) critical current in the range of 10000 Oe has been observed. The dc SQUID magnetization measurement indicates a possible elementary 102 nm SC…
In this paper we study numerical solutions to the quasi-classical equations of motion for a SQUID ring-radio frequency (rf) resonator system in the regime where the ring is highly hysteretic. In line with experiment, we show that for a suitable choice of of ring circuit parameters the solutions to these equations of motion comprise sets of levels in the rf voltage-current dynamics of the coupled system. We further demonstrate that transitions, both up and down, between these levels can be controlled by voltage pulses applied to the system, thus opening up the possibility of high order (e.g. 10…
Through experiments and numerical simulations we explore the behavior of rf SQUID (radio frequency superconducting quantum interference device) metamaterials, which show extreme tunability and nonlinearity. The emergent electromagnetic properties of this metamaterial are sensitive to the degree of coherent response of the driven interacting SQUIDs. Coherence suffers in the presence of disorder, which is experimentally found to be mainly due to a dc flux gradient. We demonstrate methods to recover the coherence, specifically by varying the coupling between the SQUID meta-atoms and increasing th…
A Superconducting QUantum Interference Device (SQUID) modulated by a fast oscillating magnetic flux can be used as a parametric amplifier, providing gain with very little added noise. Here, we develop linearized models to describe the parametrically flux-pumped SQUID in terms of an impedance. An unpumped SQUID acts as an inductance, the Josephson inductance, whereas a flux-pumped SQUID develops an additional, parallel element which we have coined the ``pumpistor.'' Parametric gain can be understood as a result of a negative resistance of the pumpistor. In the degenerate case, the gain is sensi…
Strong nonlinearity of a self-resonant radio frequency superconducting quantum interference device (rf-SQUID) meta-atom is explored via intermodulation (IM) measurements. Previous work in zero dc magnetic flux showed a sharp onset of IM response as the frequency sweeps through the resonance. A second onset at higher frequency was also observed, creating a prominent gap in the IM response. By extending those measurements to nonzero dc flux, new dynamics are revealed, including: dc flux tunabililty of the aforementioned gaps, and enhanced IM response near geometric resonance of the rf-SQUID. The…
We describe the performance of amplifiers in the 4 GHz--8 GHz range using Direct Current Superconducting Quantum Interference Devices(DC SQUIDs) in a lumped element configuration. We have used external impedance transformers to couple power into and out of the DC SQUIDs. By choosing appropriate values for coupling capacitors, resonator lengths and output component values, we have demonstrated useful gains in several frequency ranges with different bandwidths, showing over 27 GHz of power gain-bandwidth product. In this work, we describe our design for the 4 GHz--8 GHz range and present data de…
We show that fundamental conservation laws mandate parameter-free mechanisms of decoherence of quantum oscillations of the superconducting current between opposite directions in a SQUID -- emission of phonons and photons at the oscillation frequency. The corresponding rates are computed and compared with experimental findings. The decohering effects of external mechanical and magnetic noise are investigated.
We examine the collective behavior of two-dimensional nonlinear superconducting metamaterials using a non-contact spatially resolved imaging technique. The metamaterial is made up of sub-wavelength nonlinear oscillators in a strongly coupled 27x27 planar array of radio-frequency Superconducting QUantum Interference Devices (rf SQUIDs). By using low-temperature laser scanning microscopy we image microwave currents in the driven SQUIDs while in non-radiating dark modes and identify the clustering and uniformity of like-oscillating meta-atoms. We follow the rearrangement of coherent patterns due …
A current bias dc SQUID behaves as an anharmonic quantum oscillator controlled by a bias current and an applied magnetic flux. We consider here its two level limit consisting of the two lower energy states $| 0 \right>$ and $| 1 \right>$. We have measured energy relaxation times and microwave absorption for different bias currents and fluxes in the low microwave power limit. Decoherence times are extracted. The low frequency flux and current noise have been measured independently by analyzing the probability of current switching from the superconducting to the finite voltage state, as a functi…
We have designed and characterized a micro-SQUID with dispersive readout for use in low temperature scanning probe microscopy systems. The design features a capacitively shunted RF SQUID with a tunable resonance frequency from 5 to 12 GHz, micrometer spatial resolution and integrated superconducting coils for local application of magnetic fields. The SQUID is operated as a nonlinear oscillator with a flux- and power-dependent resonance frequency. Measurements for device characterization and noise benchmarking were carried out at 4 K. The measured flux noise above 10 kHz at 4 K is $80\;\mathrm{…
We report on the development of an analytical model describing the readout power and SQUID hysteresis parameter dependence of the resonator characteristics used for frequency encoding in microwave SQUID multiplexers. Within the context of this model, we derived the different dependencies by analyzing the Fourier components of the non-linear response of the non-hysteretic rf-SQUID. We show that our model contains the existing model as a limiting case, leading to identical analytical expressions for small readout powers. Considering the approximations we made, our model is valid for rf-SQUID hys…
SRON is developing the Frequency Domain Multiplexing (FDM) readout and the ultra low NEP TES bolometers array for the infrared spectrometer SAFARI on board of the Japanese space mission SPICA. The FDM prototype of the instrument requires critical and complex optimizations. For single pixel characterization under AC bias we are developing a simple FDM system working in the frequency range from 1 to 5 MHz, based on the open loop read-out of a linearized two-stage SQUID amplifier and high Q lithographic LC resonators. We describe the details of the experimental set-up required to achieve low powe…
Superconducting granular aluminum is attracting increasing interest due to its high kinetic inductance and low dissipation, favoring its use in kinetic inductance particle detectors, superconducting resonators or quantum bits. We perform switching current measurements on DC-SQUIDs, obtained by introducing two identical geometric constrictions in granular aluminum rings of various normal-state resistivities in the range from $ρ_\mathrm{n} = 250\,μΩ\mathrm{cm}$ to $5550\,μΩ\mathrm{cm}$. The relative high kinetic inductance of the SQUID loop, in the range of tens of nH, leads to a suppression of …
We have developed a nuclear magnetic resonance spectrometer with a series tuned input circuit for measurements on samples at millikelvin temperatures based on an integrated two-stage superconducting quantum interference device current sensor, with an energy sensitivty e = 26 +/-1 h when operated at 1.4K. To maximise the sensitivity both the NMR pickup coil and tuning capacitor need to be cooled, and the tank circuit parameters should be chosen to equalise the contributions from circulating current noise and voltage noise in the SQUID. A noise temperature TN = 7 +/-2 mK was measured, at a frequ…
We investigate the quantum dynamics of a quadratic-quartic anharmonic oscillator formed by a potential well between two potential barriers. We realize this novel potential shape with a superconducting circuit comprised of a loop interrupted by two Josephson junctions, with near-zero current bias and flux bias near half a flux quantum. We investigate escape out of the central well, which can occur via tunneling through either of the two barriers, and find good agreement with a generalized double-path macroscopic quantum tunneling theory. We also demonstrate that this system exhibits an "optimal…
We present experimental data on a one-dimensional superconducting metamaterial that is tunable over a broad frequency band. The basic building block of this magnetic thin-film medium is a single-junction (rf-) superconducting quantum interference device (SQUID). Due to the nonlinear inductance of such an element, its resonance frequency is tunable in situ by applying a dc magnetic field. We demonstrate that this results in tunable effective parameters of our metamaterial consisting of 54 SQUIDs. In order to obtain the effective magnetic permeability from the measured data, we employ a techniqu…
An overview of several dynamic properties of SQUID metamaterials is given in the presence of both constant and alternating magnetic field. The total current as a function of the driving frequency exhibits hysteretic effects which are favored by low levels of disorder. Multistability in the current states leads to multiple magnetic responses with different value of magnetic permeability. SQUID metamaterials exhibit wide-band tuneability which is periodic with the applied constant magnetic field; the numerical calculations reproduce fairly well recent experimental results. Current work also reve…
We have measured the backaction of a dc superconducting quantum interference device (SQUID) position detector on an integrated 1 MHz flexural resonator. The frequency and quality factor of the micromechanical resonator can be tuned with bias current and applied magnetic flux. The backaction is caused by the Lorentz force due to the change in circulating current when the resonator displaces. The experimental features are reproduced by numerical calculations using the resistively and capacitively shunted junction (RCSJ) model.
We have developed and measured a high-gain quantum-limited microwave parametric amplifier based on a superconducting lumped LC resonator with the inductor L including an array of 8 superconducting quantum interference devices (SQUIDs). This amplifier is parametrically pumped by modulating the flux threading the SQUIDs at twice the resonator frequency. Around 5 GHz, a maximum gain of 31 dB, a product amplitude-gain x bandwidth above 60 MHz, and a 1 dB compression point of -123 dBm at 20 dB gain are obtained in the non-degenerate mode of operation. Phase sensitive amplification-deamplification i…
The Transition-Edge Sensors (TES) is a mature, high-resolution x-ray spectrometer technology that provides a much higher efficiency than dispersive spectrometers such as gratings and crystal spectrometers. As larger arrays are developed, time-division multiplexing schemes operating at MHz frequencies are being replaced by microwave SQUID multiplexers using frequency-division multiplexing at GHz frequencies. However, the multiplexing factor achievable with microwave SQUIDs is limited by the high slew rate on the leading edge of x-ray pulses. In this paper, we propose a new multiplexing scheme f…
We have prepared meta-atoms based on radio frequency superconducting quantum interference devices (RF SQUIDs) and examined their tunability with dc magnetic field, rf current, and temperature. RF SQUIDs are superconducting split ring resonators in which the usual capacitance is supplemented with a Josephson junction, which introduces strong nonlinearity in the rf properties. We find excellent agreement between the data and a model which regards the Josephson junction as the resistively and capacitively-shunted junction. A magnetic field tunability of 80 THz/Gauss at 12 GHz is observed, a total…
Frequency Domain Multiplexed detector arrays constructed of superconducting Transition Edge Sensors in the current-summing configuration suffer from the finite impedance of the summing node which should ideally be zero. We suggest two circuits to alleviate the effect. The first circuit uses a capacitive resonant transformer to increase the voltages and decrease the currents of TES signals to overcome the parasitic inductance of the interconnections. On the SQUID chip impedance transform to the opposite direction takes place. The second circuit implements a power combiner having a better branch…
We propose a model for 1/f flux noise in superconducting devices (f is frequency). The noise is generated by the magnetic moments of electrons in defect states which they occupy for a wide distribution of times before escaping. A trapped electron occupies one of the two Kramers-degenerate ground states, between which the transition rate is negligible at low temperature. As a result, the magnetic moment orientation is locked. Simulations of the noise produced by randomly oriented defects with a density of 5*10^17 m^-2 yield 1/f noise magnitudes in good agreement with experiments.
We have fabricated arrays of High-T$_c$ Superconducting Quantum Interference Devices (SQUIDs) with randomly distributed loop sizes as sensitive antennas for Radio-Frequency (RF) waves. These sub-wavelength size devices known as Superconducting Quantum Interference Filters (SQIFs) detect the magnetic component of the electromagnetic field. We use a scalable ion irradiation technique to pattern the circuits and engineer the Josephson junctions needed to make SQUIDs. Here we report on a 300 SQUIDs series array with loops area ranging from $6$ to $60\ μm^{2}$, folded in a meander line covering a $…
We have implemented a resonant circuit that uses a SQUID as a flux-sensitive Josephson inductor for qubit readout. In contrast to the conventional switching current measurement that generates undesired quasi-particles when the SQUID switches to the voltage state, our approach keeps the readout SQUID biased along the supercurrent branch during the measurement. By incorporating the SQUID inductor in a high-Q resonant circuit, we can distinguish the two flux states of a niobium persistent-current (PC) qubit by observing a shift in the resonant frequency of both the magnitude and the phase spectra…
We have developed a Josephson parametric amplifier, comprising a superconducting coplanar waveguide resonator terminated by a dc SQUID (superconducting quantum interference device). An external field (the pump, $\sim 20$ GHz) modulates the flux threading the dc SQUID, and, thereby, the resonant frequency of the cavity field (the signal, $\sim 10$ GHz), which leads to parametric signal amplification. We operated the amplifier at different band centers, and observed amplification (17 dB at maximum) and deamplification depending on the relative phase between the pump and the signal. The noise tem…
We have designed, fabricated and measured high-Q $λ/2$ coplanar waveguide microwave resonators whose resonance frequency is made tunable with magnetic field by inserting a DC-SQUID array (including 1 or 7 SQUIDs) inside. Their tunability range is 30% of the zero field frequency. Their quality factor reaches up to 3$\times10^4$. We present a model based on thermal fluctuations that accounts for the dependance of the quality factor with magnetic field.
We present experimental results on a dispersive scheme for reading out a Josephson phase qubit. A capacitively shunted dc-SQUID is used as a nonlinear resonator which is inductively coupled to the qubit. We detect the flux state of the qubit by measuring the amplitude and phase of a microwave pulse reflected from the SQUID resonator. By this low-dissipative method, we reduce the qubit state measurement time down to 25 microseconds, which is much faster than using the conventional readout performed by switching the SQUID to its non-zero dc voltage state. The demonstrated readout scheme allows f…
We present the prototype module of our extendible and robust multichannel SQUID magnetometer system. A multi-module arrangement can be implemented by using up to 7 modules. It is intended for high-precision measurements of biomagnetism and spin precession. Further demanding applications are magnetorelaxometry and ultra-low-field nuclear magnetic resonance (ULF NMR), where pulsed fields of up to 100 mT are typically applied. The system is operated inside the Berlin Magnetically Shielded Room and equipped with 18 magnetometers consisting of niobium (Nb) wire-wound pick-up coils. A total of 16 sm…
