In this paper, we consider a cooperative communication network where multiple low-Earth-orbit (LEO) satellites provide services to multiple ground users (GUs) cooperatively at the same time and on the same frequency. The multi-satellite cooperation has great potential in extending communication coverage and increasing spectral efficiency. Considering that the on-board radio-frequency circuit resources and computation resources on each satellite are restricted, we aim to propose a low-complexity yet efficient multi-satellite cooperative transmission framework. Specifically, we first propose a hybrid beamforming method consisting of analog beamforming for beam alignment and digital beamforming for interference mitigation. Then, to establish appropriate connections between the satellites and GUs, we propose a heuristic user scheduling algorithm which determines the connections according to the total spectral efficiency increment of the multi-satellite cooperative network. Next, considering the intrinsic connection between beamforming and user scheduling, a joint hybrid beamforming and user scheduling (JHU) scheme is proposed to dramatically improve the performance of the multi-satellite cooperative network. In addition to the single-connection scenario, we also consider the multi-connection case using the JHU scheme. Extensive simulations conducted over different LEO satellite constellations and across various GU locations demonstrate the superiority of the proposed schemes in both overall and per-user spectral efficiencies.
In the small-cell networks (SCNs) with multiple small-cell base stations (ScBSs), the joint design of beamforming vectors, user scheduling and ScBS sleeping is investigated with the constraints on proportional rate. A long-term grid-energy expenditure minimization problem is formulated for the considered SCNs, which are powered by the smart grid and natural renewable energy. Since the scheduled user indicators are coupled with the beamforming vectors, the formulated problem is challenging to handle. In order to decouple the beamforming vectors from the scheduled user indicators, the Lyapunov o…
The omnipresence of IoT devices in Industry 4.0 is expected to foster higher reliability, safety, and efficiency. However, interconnecting a large number of wireless devices without jeopardizing the system performance proves challenging. To address the requirements of future industries, we investigate the cross-layer design of beamforming and scheduling for layered-division multiplexing (LDM) systems in millimeter-wave bands. Scheduling is crucial as the devices in industrial settings are expected to proliferate rapidly. Also, highly performant beamforming is necessary to ensure scalability. B…
In this paper, we consider a cooperative communication network where multiple satellites provide services for ground users (GUs) (at the same time and on the same frequency). The communication and computational resources on satellites are usually restricted and the satellite-GU link determination affects the communication performance significantly when multiple satellites provide services for multiple GUs in a collaborative manner. Therefore, considering the limitation of the on-board radio-frequency chains, we first propose a hybrid beamforming method consisting of analog beamforming for beam…
Most prior works on intelligent reflecting surface (IRS) merely consider point-to-point communications, including a single user, for ease of analysis. Nevertheless, a practical wireless system needs to accommodate multiple users simultaneously. Due to the lack of frequency-selective reflection, namely the set of phase shifts cannot be different across frequency subchannels, the integration of IRS imposes a fundamental challenge to frequency-multiplexing approaches such as frequency-division multiple access (FDMA) and the widely adopted technique called orthogonal FDMA (OFDMA). It motivates us …
In this work, we study the problem of relay beamforming for an underlay cognitive radio relay network using amplify-and-forward (AF) relaying technique. We consider a cognitive radio network consisting of single primary and multiple secondary transmitters/receivers. In addition, there are several relay nodes that help both primary and secondary networks. We propose a new beamforming method for relays' transmission, in which the beamforming weights at the relays are the solution of an optimization problem. The objective of the optimization problem is maximizing the worst case signal to interfer…
In this manuscript, we present an energy-efficient alternating optimization framework based on the multi-antenna ambient backscatter communication (AmBSC) assisted cooperative non-orthogonal multiple access (NOMA) for next-generation (NG) internet-of-things (IoT) enabled communication networks. Specifically, the energy-efficiency maximization is achieved for the considered AmBSC-enabled multi-cluster cooperative IoT NOMA system by optimizing the active-beamforming vector and power-allocation coefficients (PAC) of IoT NOMA users at the transmitter, as well as passive-beamforming vector at the m…
Opportunistic scheduling and beamforming schemes with reduced feedback are proposed for MIMO-OFDMA downlink systems. Unlike the conventional beamforming schemes in which beamforming is implemented solely by the base station (BS) in a per-subcarrier fashion, the proposed schemes take advantages of a novel channel decomposition technique to perform beamforming jointly by the BS and the mobile terminal (MT). The resulting beamforming schemes allow the BS to employ only {\em one} beamforming matrix (BFM) to form beams for {\em all} subcarriers while each MT completes the beamforming task for each …
In a multicell multiuser MIMO downlink employing random beamforming as the transmission scheme, the heterogeneous large scale channel effects of intercell and intracell interference complicate analysis of distributed scheduling based systems. In this paper, we extend the analysis in [1] and [2] to study the aforementioned challenging scenario. The cumulative distribution function (CDF)-based scheduling policy utilized in [1] and [2] is leveraged to maintain fairness among users and simultaneously obtain multiuser diversity gain. The closed form expression of the individual sum rate for each us…
Opportunistic scheduling and beamforming schemes have been proposed previously by the authors for reduced-feedback MIMO-OFDMA downlink systems where the MIMO channel of each subcarrier is decomposed into layered spatial subchannels. It has been demonstrated that significant feedback reduction can be achieved by returning information about only one beamforming matrix (BFM) for all subcarriers from each MT, compared to one BFM for each subcarrier in the conventional schemes. However, since the previously proposed channel decomposition was derived based on singular value decomposition, the result…
User scheduling, beamforming and energy coordination are investigated in smart-grid powered cellular networks (SGPCNs), where the base stations are powered by a smart grid and natural renewable energy sources. Heterogeneous energy coordination is considered in SGPCNs, namely energy merchandizing with the smart grid and energy exchanging among the base stations. A long-term grid-energy expenditure minimization problem with proportional-rate constraints is formulated for SGPCNs. Since user scheduling is coupled with the beamforming vectors, the formulated problem is challenging to handle via sta…
We consider in this paper a new intelligent reflecting surface (IRS)-aided LEO satellite communication system, by utilizing the controllable phase shifts of massive passive reflecting elements to achieve flexible beamforming, which copes with the time-varying channel between the high-mobility satellite (SAT) and ground node (GN) cost-effectively. In particular, we propose a new architecture for IRS-aided LEO satellite communication where IRSs are deployed at both sides of the SAT and GN, and study their cooperative passive beamforming (CPB) design over line-of-sight (LoS)-dominant single-refle…
Opportunistic scheduling and beamforming schemes are proposed for multiuser MIMO-SDMA downlink systems with linear combining in this work. Signals received from all antennas of each mobile terminal (MT) are linearly combined to improve the {\em effective} signal-to-noise-interference ratios (SINRs). By exploiting limited feedback on the effective SINRs, the base station (BS) schedules simultaneous data transmission on multiple beams to the MTs with the largest effective SINRs. Utilizing the extreme value theory, we derive the asymptotic system throughputs and scaling laws for the proposed sche…
In multiuser communication systems, user scheduling and beamforming (US-BF) design are two fundamental problems that are usually studied separately in the existing literature. In this work, we focus on the joint US-BF design with the goal of maximizing the set cardinality of scheduled users, which is computationally challenging due to the non-convex objective function and the coupled constraints with discrete-continuous variables. To tackle these difficulties, a successive convex approximation based US-BF (SCA-USBF) optimization algorithm is firstly proposed. Then, inspired by wireless intelli…
Intelligent reflecting surface (IRS) is a promising technology to support high performance wireless communication. By adaptively configuring the reflection amplitude and/or phase of each passive reflecting element on it, the IRS can reshape the electromagnetic environment in favour of signal transmission. This letter advances the existing research by proposing and analyzing a double-IRS aided wireless communication system. Under the reasonable assumption that the reflection channel from IRS 1 to IRS 2 is of rank 1 (e.g., line-of-sight channel), we propose a joint passive beamforming design for…
In this paper, a new user-scheduling-and-beamforming method is proposed for multi-user massive multiple-input multiple-output (massive MIMO) broadcast channels in the context of two-stage beamforming. The key ideas of the proposed scheduling method are 1) to use a set of orthogonal reference beams and construct a double cone around each reference beam to select `nearly-optimal' semi-orthogonal users based only on channel quality indicator (CQI) feedback and 2) to apply post-user-selection beam refinement with zero-forcing beamforming (ZFBF) based on channel state information (CSI) feedback onl…
This paper proposes a novel approach for designing channel estimation, beamforming and scheduling jointly for wideband massive multiple input multiple output (MIMO) systems. With the proposed approach, we first quantify the maximum number of user equipments (UEs) that can send pilots which may or may not be orthogonal. Specifically, when the channel has a maximum of $L$ multipath taps, and we allocate $\tilde{M}$ sub-carriers for the channel state information (CSI) estimation, a maximum of $\tilde{M}$ UEs CSI can be estimated ($L$ times compared to the conventional CSI estimation approach) in …
In order to address the asynchronous interference issue for a generalized scenario with multiple primary and multiple secondary receivers, in this paper, we propose an innovative cooperative beamforming technique. In particular, the cooperative beamforming design is formulated as an optimization problem that maximizes the weighted sum achievable transmission rate of secondary destinations while it maintains the asynchronous interferences at the primary receivers below their target thresholds. In light of the intractability of the problem, we propose a two-phase suboptimal cooperative beamformi…
Reconfigurable intelligent surface (RIS) provides a promising way to build programmable wireless transmission environments. Owing to the massive number of controllable reflecting elements on the surface, RIS is capable of providing considerable passive beamforming gains. At present, most related works mainly consider the modeling, design, performance analysis and optimization of single-RIS-assisted systems. Although there are a few of works that investigate multiple RISs individually serving their associated users, the cooperation among multiple RISs is not well considered as yet. To fill the …
One of the important use-cases of 5G network is the vehicle to infrastructure (V2I) communication which requires accurate understanding about its dynamic propagation environment. As 5G base stations (BSs) tend to have multiple antennas, they will likely employ beamforming to steer their radiation pattern to the desired vehicle equipment (VE). Furthermore, since most wireless standards employ an OFDM system, each VE may use one or more sub-carriers. To this end, this paper proposes a joint design of adaptive channel prediction, beamforming and scheduling for 5G V2I communications. The channel p…
Consider the joint beamforming and quantization problem in the cooperative cellular network, where multiple relay-like base stations (BSs) connected to the central processor (CP) via rate-limited fronthaul links cooperatively serve the users. This problem can be formulated as the minimization of the total transmit power, subject to all users' signal-to-interference-plus-noise-ratio (SINR) constraints and all relay-like BSs' fronthaul rate constraints. In this paper, we first show that there is no duality gap between the considered problem and its Lagrangian dual by showing the tightness of the…
In this paper, the robust distributed relay beamforming problem is solved using the worst case approach, where the problem solution has been involved because of the effect of uncertainty of channel knowledge on the quality of service (QoS) constraints. It is shown that the original robust design, which is a non-convex semi-infinite problem (SIP), can be relaxed and reformed to a semi-definite problem (SDP). Monte-Carlo simulations are presented to verify the performance improvement of our proposed robust problem over existing robust and non-robust problems in terms of transmit power and symbol…
The performance of cloud-based small cell networks (C-SCNs) relies highly on a capacity-limited fronthaul, which degrade quality of service when it is saturated. Coded caching is a promising approach to addressing these challenges, as it provides abundant opportunities for fronthaul multicast and cooperative transmissions. This paper investigates a cache-enabled C-SCNs, in which small-cell base stations (SBSs) are connected to the central processor via fronthaul, and can prefetch popular contents by applying maximum distance separable (MDS) codes. To fully capture the benefits of fronthaul mul…
The evaluation of the performance of clustered cooperative beamforming in cellular networks generally requires the solution of complex non-convex optimization problems. In this letter, a framework based on a hypergraph formalism is proposed that enables the derivation of a performance characterization of clustered cooperative beamforming in terms of per-user degrees of freedom (DoF) via the efficient solution of a coloring problem. An emerging scenario in which clusters of cooperative base stations (BSs) arise is given by cellular networks with edge caching. In fact, clusters of BSs that share…
In this paper, linear beamforming design for amplify-and-forward relaying cellular networks is considered, in which base station, relay station and mobile terminals are all equipped with multiple antennas. The design is based on minimum mean-square-error criterion, and both uplink and downlink scenarios are considered. It is found that the downlink and uplink beamforming design problems are in the same form, and iterative algorithms with the same structure can be used to solve the design problems. For the specific cases of fully loaded or overloaded uplink systems, a novel algorithm is derived…
This paper studies the joint multicast beamforming and user scheduling problem, with the objective of minimizing total transmitting power across multiple channels by jointly assigning each user to appropriate channel and designing multicast beamformer for each channel. The problem of interest is formulated in two different optimization problems, a mixed binary quadratically constrained quadratic program and a highly-structured nonsmooth program. Two different algorithms, based on convex relaxation and convex restriction, respectively, are proposed to solve the problem. The performance ratio be…
Intelligent reflecting surface (IRS) has emerged as an enabling technology to achieve smart and reconfigurable wireless communication environment cost-effectively. Prior works on IRS mainly consider its passive beamforming design and performance optimization without the inter-IRS signal reflection, which thus do not unveil the full potential of multi-IRS assisted wireless networks. In this paper, we study a double-IRS assisted multi-user communication system with the \emph{cooperative} passive beamforming design that captures the multiplicative beamforming gain from the inter-IRS channel. Unde…
Relay selection enhances the performance of the cooperative networks by selecting the links with higher capacity. Meanwhile link adaptation improves the spectral efficiency of wireless data-centric networks through adapting the modulation and coding schemes (MCS) to the current link condition. In this paper, relay selection is combined with link adaptation for distributed beamforming in a two-hop regenerative cooperative system. A novel signaling mechanism and related optimal algorithms are proposed for joint relay selection and link adaptation. In the proposed scheme, there is no need to feed…
Cooperative beamforming (CB) has been proposed as a special case of coordinated multi-point techniques in wireless communications. In wireless sensor networks, CB can enable low power communication by allowing a collection of sensor nodes to transmit data simultaneously to a distant fusion center in one hop. Besides the traditional CB approach where all nodes need to share and transmit the same data, a more recent technique allows each node to transmit its own data while still achieving the benefits of cooperation. However, the intricacies of varying beamforming gains in the direct sequence sp…
User scheduling and beamforming design are two crucial yet coupled topics for wireless communication systems. They are usually optimized separately with conventional optimization methods. In this paper, a novel cross-layer optimization problem is considered, namely, the user scheduling and beamforming are jointly discussed subjecting to the requirement of per-user quality of service (QoS) and the maximum allowable transmit power for multicell multiuser joint transmission networks. To achieve the goal, a mixed discrete-continue variables combinational optimization problem is investigated with a…
This correspondence studies the downlink transmission in a multi-cell system, where multiple base stations (BSs) each with multiple antennas cooperatively design their respective transmit beamforming vectors to optimize the overall system performance. For simplicity, it is assumed that all mobile stations (MSs) are equipped with a single antenna each, and there is one active MS in each cell at one time. Accordingly, the system of interests can be modeled by a multiple-input single-output (MISO) interference channel (IC), termed as MISO-IC, with interference treated as noise. We propose a new m…
We investigate uplink user scheduling for millimeter wave (mmWave) hybrid analog/digital beamforming systems with low-resolution analog-to-digital converters (ADCs). Deriving new scheduling criteria for the mmWave systems, we show that the channel structure in the beamspace, in addition to the channel magnitude and orthogonality, plays a key role in maximizing the achievable rates of scheduled users due to quantization error. The criteria show that to maximize the achievable rate for a given channel gain, the channels of the scheduled users need to have (1) as many propagation paths as possibl…
Base station (BS) cooperation can turn unwanted interference to useful signal energy for enhancing system performance. In the cooperative downlink, zero-forcing beamforming (ZFBF) with a simple scheduler is well known to obtain nearly the performance of the capacity-achieving dirty-paper coding. However, the centralized ZFBF approach is prohibitively complex as the network size grows. In this paper, we devise message passing algorithms for realizing the regularized ZFBF (RZFBF) in a distributed manner using belief propagation. In the proposed methods, the overall computational cost is decompos…
This paper investigates a device-to-device (D2D) cooperative computing system, where an user can offload part of its computation task to nearby idle users with the aid of an intelligent reflecting surface (IRS). We propose to minimize the total computing delay via jointly optimizing the computation task assignment, transmit power, bandwidth allocation, and phase beamforming of the IRS. To solve the formulated problem, we devise an alternating optimization algorithm with guaranteed convergence. In particular, the task assignment strategy is derived in closed-form expression, while the phase bea…
The energy-efficient (EE) design problem is very important to design a good performance network. Besides this, the security of communication is also important. Based on the new IRS technology, the EE maximization problem is formed in this paper for secure communication. We proposed a solution that outperformed other methods.
To meet the ever growing demand for both high throughput and uniform coverage in future wireless networks, dense network deployment will be ubiquitous, for which co- operation among the access points is critical. Considering the computational complexity of designing coordinated beamformers for dense networks, low-complexity and suboptimal precoding strategies are often adopted. However, it is not clear how much performance loss will be caused. To enable optimal coordinated beamforming, in this paper, we propose a framework to design a scalable beamforming algorithm based on the alternative dir…
Transmit optimization and resource allocation for wireless cooperative networks with channel state information (CSI) uncertainty are important but challenging problems in terms of both the uncertainty modeling and performance op- timization. In this paper, we establish a generic stochastic coordinated beamforming (SCB) framework that provides flex- ibility in the channel uncertainty modeling, while guaranteeing optimality in the transmission strategies. We adopt a general stochastic model for the CSI uncertainty, which is applicable for various practical scenarios. The SCB problem turns out to…
This paper investigates multiple intelligent reflecting surfaces (IRSs) aided wireless network, where the IRSs are deployed to cooperatively assist communications between a multi-antenna base station (BS) and multiple single-antenna cell-edge users. We aim at maximizing the weighted sum rate of all the cell-edge users by jointly optimizing the BS's transmit beamforming and IRS's phase shifts. Especially, the beamforming is optimally solved by the Lagrangian method, and the phase shifts are obtained based on the Riemannian manifold conjugate gradient (RMCG) method. Numerical results show that a…
This paper presents a two-phase cooperative communication strategy and an optimal power allocation strategy to transmit sensor observations to a fusion center in a large-scale sensor network. Outage probability is used to evaluate the performance of the proposed system. Simulation results demonstrate that: 1) when signal-to-noise ratio is low, the performance of the proposed system is better than that of the multiple-input and multiple-output system over uncorrelated slow fading Rayleigh channels; 2) given the transmission rate and the total transmission SNR, there exists an optimal power allo…
Extending network lifetime of battery-operated devices is a key design issue that allows uninterrupted information exchange among distributive nodes in wireless sensor networks. Collaborative beamforming (CB) and cooperative transmission (CT) have recently emerged as new communication techniques that enable and leverage effective resource sharing among collaborative/cooperative nodes. In this paper, we seek to maximize the lifetime of sensor networks by using the new idea that closely located nodes can use CB/CT to reduce the load or even avoid packet forwarding requests to nodes that have cri…
The combination of cell-free massive multiple-input multiple-output (CF-mMIMO) and reconfigurable intelligent surface (RIS) is envisioned as a promising paradigm to improve network capacity and enhance coverage capability. However, to reap full benefits of RIS-aided CF-mMIMO, the main challenge is to efficiently design cooperative beamforming (CBF) at base stations (BSs), RISs, and users. Firstly, we investigate the fractional programing to convert the weighted sum-rate (WSR) maximization problem into a tractable optimization problem. Then, the alternating optimization framework is employed to…
This paper considers hybrid beamforming (HB) for downlink multiuser massive multiple input multiple output (MIMO) systems with frequency selective channels. For this system, first we determine the required number of radio frequency (RF) chains and phase shifters (PSs) such that the proposed HB achieves the same performance as that of the digital beamforming (DB) which utilizes $N$ (number of transmitter antennas) RF chains. We show that the performance of the DB can be achieved with our HB just by utilizing $r_t$ RF chains and $2r_t(N-r_t + 1)$ PSs, where $r_t \leq N$ is the rank of the combin…
In this paper, we propose a cooperative approach to improve the security of both primary and secondary systems in cognitive radio multicast communications. During their access to the frequency spectrum licensed to the primary users, the secondary unlicensed users assist the primary system in fortifying security by sending a jamming noise to the eavesdroppers, while simultaneously protect themselves from eavesdropping. The main objective of this work is to maximize the secrecy rate of the secondary system, while adhering to all individual primary users' secrecy rate constraints. In the case of …
We consider the problem of scheduling and power allocation for the downlink of a 5G cellular system operating in the millimeter wave (mmWave) band and serving two sets of users: fix-rate (FR) users typically seen in device-to-device (D2D) communications, and variable-rate (VR) users, or high data rate services. The scheduling objective is the weighted sum-rate of both FR and VR users, and the constraints ensure that active FR users get the required rate. The weights of the objective function provide a trade-off between the number of served FR users and the resources allocated to VR users. For …
In this paper, we consider a three-node cooperative wireless powered communication system consisting of a multi-antenna hybrid access point (H-AP) and a single-antenna relay and a single-antenna user. The energy constrained relay and user first harvest energy in the downlink and then the relay assists the user using the harvested power for information transmission in the uplink. The optimal energy beamforming vector and the time split between harvest and cooperation are investigated. To reduce the computational complexity, suboptimal designs are also studied, where closed-form expressions are …
This paper analyzes Hybrid Beamforming (HBF) and Multi-User Multiple-Input Multiple-Output (MU-MIMO) in millimeter wave (mmWave) 5th generation (5G) cellular networks considering the full protocol stack with TCP/IP traffic and MAC scheduling. Prior work on HBF and MU-MIMO has assumed full-buffer transmissions and studied link-level performance. We report non-trivial interactions between the HBF technique, the front-loaded channel estimation pilot scheme in NR, and the constraints of MU-MIMO scheduling. We also report that joint multi-user beamforming design is imperative, in the sense that the…
Cooperative beamforming in relay networks is considered, in which a source transmits to its destination with the help of a set of cooperating nodes. The source first transmits locally. The cooperating nodes that receive the source signal retransmit a weighted version of it in an amplify-and-forward (AF) fashion. Assuming knowledge of the second-order statistics of the channel state information, beamforming weights are determined so that the signal-to-noise ratio (SNR) at the destination is maximized subject to two different power constraints, i.e., a total (source and relay) power constraint, …
Via collaborative beamforming, nodes in a wireless network are able to transmit a common message over long distances in an energy efficient fashion. However, the process of making available the same message to all collaborating nodes introduces delays. In this paper, a MAC-PHY cross-layer scheme is proposed that enables collaborative beamforming at significantly reduced collaboration overhead. It consists of two phases. In the first phase, nodes transmit locally in a random access time-slotted fashion. Simultaneous transmissions from multiple source nodes are viewed as linear mixtures of all t…
