arXivDaily arXiv每日学术速递 周一至周五更新
arXiv周末暂无论文更新,休息一下吧,周末愉快~~
arXiv 2212.03110physics.ins-dethep-ex
收藏

ATLAS sTGC探测器的高计数率研究及前端放大器输入滤波电路的优化

High Rate Studies of the ATLAS sTGC Detector and Optimization of the Filter Circuit on the Input of the Front-End Amplifier

Siyuan Sun, Luca Moleri, Gerardo Vasquez, Peter Teterin, Sabrina Corsetti, Liang Guan, Benoit Lefebvre, Enrique Kajomovitz, Lorne Levinson, Nachman Lupu, Rob Mc… 展开作者

Siyuan Sun, Luca Moleri, Gerardo Vasquez, Peter Teterin, Sabrina Corsetti, Liang Guan, Benoit Lefebvre, Enrique Kajomovitz, Lorne Levinson, Nachman Lupu, Rob McPherson, Alexander Vdovin, Rongkun Wang, Bing Zhou, Junjie Zhu

AI总结:

本文研究ATLAS sTGC探测器在高计数率下的性能,揭示电子学死时间是效率损失主因,并通过优化π型网络输入滤波器和上拉电阻来减少死时间、降低效率损失。

摘要:

欧洲核子研究中心(CERN)的大型强子对撞机(LHC)预计将在2029年前升级为高亮度大型强子对撞机(HL-LHC),并实现约5至7.5×10^34 cm^-2 s^-1的瞬时亮度。这比Run 2期间所达到的瞬时亮度提高了3到4倍以上。新小轮(NSW)升级的设计目标是在这种高本底计数率环境中高效运行。本文总结了使用接近最终版本的前端电子学对小条薄间隙室(sTGC)在高计数率下的多项性能研究。我们证明效率随计数率的分布可以用指数衰减很好地描述,其中电子学死时间是在高计数率下效率损失的主要原因。随后,我们展示了几种能够减少电子学死时间从而最小化效率损失的方法。其中一种方法是安装π型网络输入滤波器或上拉电阻,以最小化进入放大器的电荷输入。我们利用测量结果优化了π型网络的电容和上拉电阻的阻值。本文展示的结果不仅对最终确定前端板上的元器件至关重要,而且对于在ATLAS实验洞内设定sTGC探测器及电子学的最佳运行参数也至关重要。

英文摘要:

The Large Hadron Collider (LHC) at CERN is expected to be upgraded to the High-Luminosity LHC (HL-LHC) by 2029 and achieve instantaneous luminosity around 5 - 7.5 $\times$ 10$^{34}$cm$^{-2}$ s$^{-1}$. This represents a more than 3-4 fold increase in the instantaneous luminosity compared to what has been achieved in Run 2. The New Small Wheel (NSW) upgrade is designed to be able to operate efficiently in this high background rate environment. In this article, we summarize multiple performance studies of the small-strip Thin Gap Chamber (sTGC) at high rate using nearly final front-end electronics. We demonstrate that the efficiency versus rate distribution can be well described by an exponential decay with electronics dead-time being the primary cause of loss of efficiency at high rate. We then demonstrate several methods that can decrease the electronics dead-time and therefore minimize efficiency loss. One such method is to install either a pi-network input filter or pull-up resistor to minimize the charge input into the amplifier. We optimized the pi-network capacitance and pull-up resistor resistance using the results from our measurements. The results shown here were not only critical to finalizing the components on the front-end board, but also are critical for setting the optimal operating parameters of the sTGC detector and electronics in the ATLAS cavern.

机构、总结、中文摘要均由AI分析而来,可能存在错误,请以论文正文为准。

↑