In Massive MIMO base stations (BSs), the hardware design needs to balance high spectral efficiency (SE) with low complexity. The level of hardware impairments (HWIs) indicates how strong the signal distortion introduced by hardware imperfections is. In particular, the analog-to-digital converters (ADCs) have an important impact on signal distortion and power consumption. This article addresses the fundamental problem of selecting the optimal hardware quality in the Massive MIMO space. In particular, we examine the optimal HWI and ADC bit allocation per BS antenna to maximize the SE. The results show that in co-located arrays with low channel gain variations across antennas, equal ADC bit allocation is optimal. In contrast, cell-free Massive MIMO systems benefit the most from optimizing the ADC bit allocation achieving improvements in the order of 2 [bit-per-channel-use] per user equipment when using regularized zero-forcing (RZF). In addition, when including the impact of power consumption in cell-free Massive MIMO with RZF, allocating low values of mixed ADC bit resolutions across the BS antennas can increase the energy efficiency up to 30% compared to equal ADC bit allocation.
The low-resolution analog-to-digital convertor (ADC) is a promising solution to significantly reduce the power consumption of radio frequency circuits in massive multiple-input multiple-output (MIMO) systems. In this letter, we investigate the uplink spectral efficiency (SE) of massive MIMO systems with low-resolution ADCs over Rician fading channels, where both perfect and imperfect channel state information are considered. By modeling the quantization noise of low-resolution ADCs as an additive quantization noise, we derive tractable and exact approximation expressions of the uplink SE of ma…
This paper investigated the uplink of multi-user massive multi-input multi-output (MIMO) systems with a mixed analog-to-digital converter (ADC) receiver architecture, in which some antennas are equipped with costly full-resolution ADCs and others with less expensive low-resolution ADCs. A closed-form approximation of the achievable spectral efficiency (SE) with the maximum-ratio combining (MRC) detector is derived. Based on this approximated result, the effects of the number of base station antennas, the transmit power, the proportion of full-resolution ADCs in the mixed-ADC structure, and the…
This paper considers a multiple-input multiple-output (MIMO) system with low-resolution analog-to-digital converters (ADCs). In this system, the paper presents a new MIMO detection approach using coding theory. The principal idea of the proposed approach is to transform a non-linear MIMO channel to a linear MIMO channel by leveraging both a $p$-level quantizer and a lattice code where $p\geq 2$. After transforming to the linear MIMO channel with the sets of finite input and output elements, efficient MIMO detection methods are proposed to attain both diversity and multiplexing gains by using a…
Nowadays, millimeter-wave (mmWave) massive multiple-input multiple-output (MIMO) systems is a favorable candidate for the fifth generation (5G) cellular systems. However, a key challenge is the high power consumption imposed by its numerous radio frequency (RF) chains, which may be mitigated by opting for low-resolution analog-to-digital converters (ADCs), whilst tolerating a moderate performance loss. In this article, we discuss several important issues based on the most recent research on mmWave massive MIMO systems relying on low-resolution ADCs. We discuss the key transceiver design challe…
In this letter, we derive an approximate analytical expression for the uplink achievable rate of a massive multi-input multi-output (MIMO) antenna system when finite precision analog-digital converters (ADCs) and the common maximal ratio combining technique are used at the receivers. To obtain this expression, we treat quantization noise as an additive quantization noise model. Considering the obtained expression, we show that low-resolution ADCs lead to a decrease in the achievable rate but the performance loss can be compensated by increasing the number of receiving antennas. In addition, we…
Multiple antenna systems have been extensively used by standards designing multi-gigabit communication systems operating in bandwidth of several GHz. In this paper, we study the use of transmitter (Tx) beamforming techniques to improve the performance of a MIMO system with a low precision ADC. We motivate an approach to use eigenmode transmit beamforming (which imposes a diagonal structure in the complete MIMO system) and use an eigenmode power allocation which minimizes the uncoded BER of the finite precision system. Although we cannot guarantee optimality of this approach, we observe that ev…
We investigate massive multiple-input-multiple output (MIMO) uplink systems with 1-bit analog-to-digital converters (ADCs) on each receiver antenna. Receivers that rely on 1-bit ADC do not need energy-consuming interfaces such as automatic gain control (AGC). This decreases both ADC building and operational costs. Our design is based on maximal ratio combining (MRC), zero-forcing (ZF), and least squares (LS) detection, taking into account the effects of the 1-bit ADC on channel estimation. Through numerical results, we show good performance of the system in terms of mutual information and symb…
We study the spectral efficiency (SE) of a mixed-ADC massive MIMO system in which K single-antenna users communicate with a base station (BS) equipped with M antennas connected to N high-resolution ADCs and M-N one-bit ADCs. This architecture has been proposed as an approach for realizing massive MIMO systems with reasonable power consumption. First, we investigate the effectiveness of mixed-ADC architectures in overcoming the channel estimation error caused by coarse quantization. For the channel estimation phase, we study to what extent one can combat the SE loss by exploiting just N << M pa…
Analog-to-digital converters (ADCs) stand for a significant part of the total power consumption in a massive MIMO base station. One-bit ADCs are one way to reduce power consumption. This paper presents an analysis of the spectral efficiency of single-carrier and OFDM transmission in massive MIMO systems that use one-bit ADCs. A closed-form achievable rate, i.e., a lower bound on capacity, is derived for a wideband system with a large number of channel taps that employs low-complexity linear channel estimation and symbol detection. Quantization results in two types of error in the symbol detect…
Millimeter wave (mmWave) systems operating over a wide bandwidth and using a large number of antennas impose a heavy burden on power consumption. In a massive multiple-input multiple-output (MIMO) uplink, analog-to-digital con- verters (ADCs) would be the primary consumer of power in the base station receiver. This paper proposes a bit allocation (BA) method for mmWave multi-user (MU) massive MIMO systems under a power constraint. We apply ADCs to the outputs of an analog phased array for beamspace projection to exploit mmWave channel sparsity. We relax a mean square quantization error (MSQE) …
One way to reduce the power consumption in large-scale multiple-input multiple-output (MIMO) systems is to employ low-resolution analog-to-digital converters (ADCs). In this paper, we investigate antenna selection for large-scale MIMO receivers with low-resolution ADCs, thereby providing more flexibility in resolution and number of ADCs. To incorporate quantization effects, we generalize an existing objective function for a greedy capacity-maximization antenna selection approach. The derived objective function offers an opportunity to select an antenna with the best tradeoff between the additi…
In this paper, we present a successive-cancellation-soft-output (SCSO) detector for an uplink multiuser multiple-input-multiple-output (MU-MIMO) system with one-bit analog-to-digital converters (ADCs). The proposed detector produces soft outputs (e.g., log-likelihood ratios (LLRs)) from one-bit quantized observations in a successive way: each user k's message is sequentially decoded from a channel decoder $k$ for $k=1,...,K$ in that order, and the previously decoded messages are exploited to improve the reliabilities of LLRs. Furthermore, we develop an efficient greedy algorithm to optimize a …
This letter considers the architecture of distributed antenna system, which is made up of a massive number of single-antenna remote radio heads (RRHs), some with full-resolution but others with low-resolution analog-to-digital converter (ADC) receivers. This architecture is greatly motivated by its high energy efficiency and low-cost implementation. We derive the worst-case uplink spectral efficiency (SE) of the system assuming a frequency-flat channel and maximum-ratio combining (MRC), and reveal that the SE increases as the number of quantization bits for the low-resolution ADCs increases, a…
The fundamental limits of communication over multiple-input multiple-output (MIMO) networks are considered when a limited number of one-bit analog to digital converters (ADC) are used at the receiver terminals. Prior works have mainly focused on point-to-point communications, where receiver architectures consisting of a concatenation of an analog processing module, a limited number of one-bit ADCs with non-adaptive thresholds, and a digital processing module are considered. In this work, a new receiver architecture is proposed which utilizes adaptive threshold one-bit ADCs - where the ADC thre…
High resolution analog to digital converters (ADCs) are conventionally used at the receiver terminals to store an accurate digital representation of the received signal, thereby allowing for reliable decoding of transmitted messages. However, in a wide range of applications, such as communication over millimeter wave and massive multiple-input multiple-output (MIMO) systems, the use of high resolution ADCs is not feasible due to power budget limitations. In the conventional fully digital receiver design, where each receiver antenna is connected to a distinct ADC, reducing the ADC resolution le…
Using a very low-resolution analog-to-digital convertor (ADC) unit at each antenna can remarkably reduce the hardware cost and power consumption of a massive multiple-input multiple-output (MIMO) system. However, such a pure low-resolution ADC architecture also complicates parameter estimation problems such as time/frequency synchronization and channel estimation. A mixed-ADC architecture, where most of the antennas are equipped with low-precision ADCs while a few antennas have full-precision ADCs, can solve these issues and actualize the potential of the pure low-resolution ADC architecture. …
In this paper, we investigate a multi-cell millimeter wave (mmWave) massive multiple-input multiple-output (MIMO) network with low-precision analog-to-digital converters (ADCs) at the base station (BS). Each cell serves multiple users and each user is equipped with multiple antennas but driven by a single RF chain. We first introduce a channel estimation strategy for the mmWave massive MIMO network and analyze the achievable rate with imperfect channel state information. Then, we derive an insightful lower bound for the achievable rate, which becomes tight with a growing number of users. The b…
We develop a broadband channel estimation algorithm for millimeter wave (mmWave) multiple input multiple output (MIMO) systems with few-bit analog-to-digital converters (ADCs). Our methodology exploits the joint sparsity of the mmWave MIMO channel in the angle and delay domains. We formulate the estimation problem as a noisy quantized compressed-sensing problem and solve it using efficient approximate message passing (AMP) algorithms. In particular, we model the angle-delay coefficients using a Bernoulli-Gaussian-mixture distribution with unknown parameters and use the expectation-maximization…
Motivated by the demand for energy-efficient communication solutions in the next generation cellular network, a mixed-ADC receiver architecture for massive multiple input multiple output (MIMO) systems is proposed, which differs from previous works in that herein one-bit analog-to-digital converters (ADCs) partially replace the conventionally assumed high-resolution ADCs. The information-theoretic tool of generalized mutual information (GMI) is exploited to analyze the achievable data rates of the proposed system architecture and an array of analytical results of engineering interest are obtai…
In this paper, we investigate the massive MIMO relay system, where the relay station (RS) forwards the signals from multiple remote users to the base station (BS). Large-scale antenna arrays in conjunction with low-resolution analog-to-digital converters (ADCs) are equipped at the RS and the BS to guarantee the high spectral efficiency with low cost. Considering the ever-present spatial correlation at both the RS and the BS, we first study the canonical channel estimation process, from which a tractable equivalent form of the channel estimate is extracted for further analysis. Under these tran…
We investigate the uplink throughput achievable by a multiple-user (MU) massive multiple-input multiple-output (MIMO) system in which the base station is equipped with a large number of low-resolution analog-to-digital converters (ADCs). Our focus is on the case where neither the transmitter nor the receiver have any a priori channel state information. This implies that the fading realizations have to be learned through pilot transmission followed by channel estimation at the receiver, based on coarsely quantized observations. We propose a novel channel estimator, based on Bussgang's decomposi…
Massive multiple-input multiple-output (M-MIMO) architecture is the workhorse of modern communication systems. Currently, two fundamental bottlenecks, namely, power consumption and receiver saturation, limit the full potential achievement of this technology. These bottlenecks are intricately linked with the analog-to-digital converter (ADC) used in each radio frequency (RF) chain. The power consumption in MIMO systems grows exponentially with the ADC's bit budget while ADC saturation causes permanent loss of information. This motivates the need for a solution that can simultaneously tackle the…
Communication systems with low-resolution analog-to-digital-converters (ADCs) can exploit channel state information at the transmitter and receiver. This paper presents codebook designs and performance analyses for limited feedback MIMO systems with finite-bit ADCs. A point-to-point single-user channel is firstly considered. When the received signal is sliced by 1-bit ADCs, the absolute phase at the receiver is important to align the phase of the received signals. A new codebook design for beamforming, which separately quantizes the channel direction and the residual phase, is therefore propos…
Hybrid analog-digital precoding architectures and low-resolution analog-to-digital converter (ADC) receivers are two solutions to reduce hardware cost and power consumption for millimeter wave (mmWave) multiple-input multiple-output (MIMO) communication systems with large antenna arrays. In this study, we consider a mmWave MIMO-OFDM receiver with a generalized hybrid architecture in which a small number of radio-frequency (RF) chains and low-resolution ADCs are employed simultaneously. Owing to the strong nonlinearity introduced by low-resolution ADCs, the task of data detection is challenging…
In millimeter wave (mmWave) systems, we investigate uplink user scheduling when a basestation employs low-resolution analog-to-digital converters (ADCs) with a large number of antennas. To reduce power consumption in the receiver, low-resolution ADCs can be a potential solution for mmWave systems in which many antennas are likely to be deployed to compensate for the large path loss. Due to quantization error, we show that the channel structure in the beamspace, in addition to the channel magnitude and beamspace orthogonality, plays a key role in maximizing the achievable rates of scheduled use…
This paper considers a multiple-input multiple-output (MIMO) receiver with very low-precision analog-to-digital convertors (ADCs) with the goal of developing massive MIMO antenna systems that require minimal cost and power. Previous studies demonstrated that the training duration should be {\em relatively long} to obtain acceptable channel state information. To address this requirement, we adopt a joint channel-and-data (JCD) estimation method based on Bayes-optimal inference. This method yields minimal mean square errors with respect to the channels and payload data. We develop a Bayes-optima…
In this paper, we analyze the ergodic rate of single transmit antenna selection (TAS) in low-resolution analog-to-digital converter (ADC) systems. Using low-resolution ADCs is a potential power-reduction solution for multiple antenna systems. Low-resolution ADC systems with TAS can further reduce cost and power consumption in wireless transceivers. Considering such systems, we derive the approximated lower bound of ergodic rate with TAS. Here, we exploit the approximated distribution of the sum of Weibull random variables to address the challenge involved in analyzing the quantization error. W…
The use of low precision (e.g., 1-3 bits) analog-to-digital convenors (ADCs) in very large multiple-input multiple-output (MIMO) systems is a technique to reduce cost and power consumption. In this context, nevertheless, it has been shown that the training duration is required to be {\em very large} just to obtain an acceptable channel state information (CSI) at the receiver. A possible solution to the quantized MIMO systems is joint channel-and-data (JCD) estimation. This paper first develops an analytical framework for studying the quantized MIMO system using JCD estimation. In particular, w…
The aim of this paper is to investigate the recently developed mixed-ADC architecture for frequency-selective channels. Multi-carrier techniques such as orthogonal frequency division multiplexing (OFDM) are employed to handle inter-symbol interference (ISI). A frequency-domain equalizer is designed for mitigating the inter-carrier interference (ICI) introduced by the nonlinearity of one-bit quantization. For static single-input-multiple-output (SIMO) channels, a closed-form expression of the generalized mutual information (GMI) is derived, and based on which the linear frequency-domain equaliz…
Advances in analog-to-digital converter (ADC) technology have opened up the possibility to directly digitize wideband radio frequency (RF) signals, avoiding the need for analog down-conversion. In this work, we consider an orthogonal frequency-division multiplexing (OFDM)-based massive multi-user (MU) multiple-input multiple-output (MIMO) uplink system that relies on direct RF-sampling at the base station and digitizes the received RF signals with 1-bit ADCs. Using Bussgang's theorem, we provide an analytical expression for the error-vector magnitude (EVM) achieved by digital down-conversion a…
The use of low-precision analog-to-digital converters (ADCs) is a low-cost and power-efficient solution for a millimeter wave (mmWave) multiple-input multiple-output (MIMO) system operating at sampling rates higher than a few Gsample/sec. This solution, however, can make significant frame-error-rates (FERs) degradation due to inter-subcarrier interference when applying conventional frequency-domain equalization techniques. In this paper, we propose computationally-efficient yet near-optimal soft-output detection methods for the coded mmWave MIMO systems with low-precision ADCs. The underlying …
The practical deployment of massive multiple-input multiple-output (MIMO) in future fifth generation (5G) wireless communication systems is challenging due to its high hardware cost and power consumption. One promising solution to address this challenge is to adopt the low-resolution analog-to-digital converter (ADC) architecture. However, the practical implementation of such architecture is challenging due to the required complex signal processing to compensate the coarse quantization caused by low-resolution ADCs. Therefore, few high-resolution ADCs are reserved in the recently proposed mixe…
This paper focuses on channel estimation in single-user and multi-user MIMO systems with multi-antenna base stations equipped with 1-bit spatial sigma-delta analog-to-digital converters (ADCs). A careful selection of the quantization voltage level and phase shift used in the feedback loop of 1-bit sigma-delta ADCs is critical to improve its effective resolution. We first develop a quantization noise model for 1-bit spatial sigma-delta ADCs. Using the developed noise model, we then present a two-step channel estimation algorithm to estimate a multipath channel parameterized by the gains, angles…
We study an uplink multiuser multiple-input multiple-output (MU-MIMO) system with one-bit analog-to-digital converters (ADCs). For such system, a supervised-learning (SL) detector has been recently proposed by modeling a non-linear end-to-end system function into a parameterized Bernoulli-like model. Despite its attractive performance, the SL detector requires a large amount of labeled data (i.e., pilot signals) to estimate the parameters of the underlying model accurately. This is because the amount of the parameters grows exponentially with the number of users. To overcome this drawback, we …
In this paper, we propose a hybrid analog-digital beamforming architecture with resolution-adaptive ADCs for millimeter wave (mmWave) receivers with large antenna arrays. We adopt array response vectors for the analog combiners and derive ADC bit-allocation (BA) solutions in closed form. The BA solutions reveal that the optimal number of ADC bits is logarithmically proportional to the RF chain's signal-to-noise ratio raised to the 1/3 power. Using the solutions, two proposed BA algorithms minimize the mean square quantization error of received analog signals under a total ADC power constraint.…
Motivated by the demand for energy-efficient communication solutions in the next generation cellular network, a mixed-ADC architecture for massive multiple input multiple output (MIMO) systems is proposed, which differs from previous works in that herein one-bit analog-to-digital converters (ADCs) partially replace the conventionally assumed high-resolution ADCs. The information-theoretic tool of generalized mutual information (GMI) is exploited to analyze the achievable data rates of the proposed system architecture and an array of analytical results of engineering interest are obtained. For …
We propose a novel low-resolution-aware recursive least squares channel estimation algorithm for uplink multi-user multiple-input multiple-output systems. In order to reduce the energy consumption, 1-bit ADCs are used on each receive antenna. The loss of performance can be recovered by the large-scale antenna arrays at the receiver. The proposed adaptive channel estimator can mitigate the distortions due to the coarse quantization. Moreover, we propose a low-resolution-aware minimum mean square error based successive interference canceler to successively mitigate the multiuser interference. Si…
This paper analyzes the performance of multicell massive multiple-input and multiple-output (MIMO) systems with variable-resolution analog-to-digital converters (ADCs). In such an architecture, each ADC uses arbitrary quantization resolution to save power and hardware cost. Along this direction, we first introduce a quantization-aware channel estimator based on additive quantization noise model (AQNM) and linear minimum mean-squared error (LMMSE) estimate theory. Afterwards, by leveraging on the estimated channel state information (CSI), we derive the asymptotic expressions of achievable uplin…
In this paper, we present a new scenario of direction of arrival (DOA) estimation using massive multiple-input multiple-output (MIMO) receive array with low-resolution analog-to-digital convertors (ADCs), which can strike a good balance between performance and circuit cost. Based on the linear additive quantization noise model (AQNM), the effect of low-resolution ADCs on the methods, such as Root-MUSIC method, is analyzed. Also, the closed-form expression of Cramer-Rao lower bound (CRLB) is derived to evaluate the performance loss caused by the low-resolution ADCs. The simulation results show …
Analog to Digital Converters (ADCs) are a major contributor to the energy consumption on the receiver side of millimeter-wave multiple-input multiple-output (MIMO) systems with large antenna arrays. Consequently, there has been significant interest in using low-resolution ADCs along with hybrid beam-forming at MIMO receivers for energy efficiency. However, decreasing the ADC resolution results in performance loss -- in terms of achievable rates -- due to increased quantization error. In this work, we study the application of practically implementable nonlinear analog operations, prior to sampl…
In this article, we investigate channel estimation for wideband millimeter-wave (mmWave) massive multiple-input multiple-output (MIMO) under hybrid architecture with lowprecision analog-to-digital converters (ADCs). To design channel estimation for the hybrid structure, both analog processing components and frequency-selective digital combiners need to be optimized. The proposed channel estimator follows the typical linear-minimum-mean-square-error (LMMSE) structure and applies for an arbitrary channel model. Moreover, for sparsity channels as in mmWave, the proposed estimator performs more ef…
In massive multiple-input multiple-output (MIMO) systems, it may not be power efficient to have a high-resolution analog-to-digital converter (ADC) for each antenna element. In this paper, a near maximum likelihood (nML) detector for uplink multiuser massive MIMO systems is proposed where each antenna is connected to a pair of one-bit ADCs, i.e., one for each real and imaginary component of the baseband signal. The exhaustive search over all the possible transmitted vectors required in the original maximum likelihood (ML) detection problem is relaxed to formulate an ML estimation problem. Then…
In this article, deep learning is applied to estimate the uplink channels for mixed analog-to-digital converters (ADCs) massive multiple-input multiple-output (MIMO) systems, where a portion of antennas are equipped with high-resolution ADCs while others employ low-resolution ones at the base station. A direct-input deep neural network (DI-DNN) is first proposed to estimate channels by using the received signals of all antennas. To eliminate the adverse impact of the coarsely quantized signals, a selective-input prediction DNN (SIP-DNN) is developed, where only the signals received by the high…
Use of low resolution analog to digital converters (ADCs) is an effective way to reduce the high power consumption of millimeter wave (mmWave) receivers. In this paper, a receiver with low resolution ADCs based on adaptive thresholds is considered in downlink mmWave communications in which the channel state information is not known a-priori and acquired through channel estimation. A performance comparison of low-complexity algorithms for power and ADC allocation among transmit and receive terminals, respectively, is provided. Through simulation of practical mmWave cellular networks, it is show…
In this paper, we investigate the capacity of massive multiple-input multiple-output (MIMO) systems corrupted by complex-valued additive white Gaussian noise (AWGN) when both the transmitter and the receiver employ 1-bit digital-to-analog converters (DACs) and 1-bit analog-to-digital-converters (ADCs). As a result of 1-bit DACs and ADCs, the transmitted and received symbols, as well as the transmit- and receive-side channel state information (CSI), are assumed to be quantized to 1-bit of information. The derived results show that the capacity of the considered massive MIMO system is $2N$ and $…
High hardware cost and high power consumption of massive multiple-input and multiple output (MIMO) are two challenges for the future wireless communications including beyond fifth generation (B5G) and sixth generation (6G). Adopting the low-resolution analog-to-digital converter (ADC) is viewed as a promising solution. Additionally, the direction of arrival (DOA) estimation is an indispensable technology for beam alignment and tracking in massive MIMO systems. Thus, in this paper, the performance of DOA estimation with mixed-ADC structure is firstly investigated. The Cramer-Rao lower bound (CR…
High power consumption and expensive hardware are two bottlenecks for practical massive multiple-input multiple-output (mMIMO) systems. One promising solution is to employ low-resolution analog-to-digital converters (ADCs) and digital-to-analog converters (DACs). In this paper, we consider a general multipair mMIMO relaying system with a mixed-ADC/DAC architecture, in which some antennas are connected to low-resolution ADCs/DACs, while the rest of the antennas are connected to high-resolution ADCs/DACs. Leveraging on the additive quantization noise model, both exact and approximate closed-form…
This paper considers an uplink multiuser massive multiple-input-multiple-output (MIMO) system with low-resolution analog-to-digital converters (ADCs), in which K users with a single-antenna communicate with one base station (BS) with Nr antennas. In this system, we present a novel multiuser MIMO detection framework that is inspired by coding theory. The key idea of the proposed framework is to create a code C of length 2Nr over a spatial domain. This code is constructed by a so-called auto-encoding function that is not designable but is completely described by a channel transformation followed…
This paper considers a multipair amplify-and-forward massive MIMO relaying system with low-resolution ADCs at both the relay and destinations. The channel state information (CSI) at the relay is obtained via pilot training, which is then utilized to perform simple maximum-ratio combining/maximum-ratio transmission processing by the relay. Also, it is assumed that the destinations use statistical CSI to decode the transmitted signals. Exact and approximated closed-form expressions for the achievable sum rate are presented, which enable the efficient evaluation of the impact of key system parame…
This paper investigates an uplink multiuser massive multiple-input multiple-output (MIMO) system with one-bit analog-to-digital converters (ADCs), in which $K$ users with a single-antenna communicate with one base station (BS) with $n_r$ antennas. In this system, we propose a novel MIMO detection framework, which is inspired by coding theory. The key idea of the proposed framework is to create a non-linear code $\Cc$ of length $n_r$ and rate $K/n_r$ using the encoding function that is completely characterized by a non-linear MIMO channel matrix. From this, a multiuser MIMO detection problem is…
This paper considers channel estimation and uplink achievable rate of the coarsely quantized massive multiple-input multiple-output (MIMO) system with radio frequency (RF) impairments. We utilize additive quantization noise model (AQNM) and extended error vector magnitude (EEVM) model to analyze the impacts of low-resolution analog-to-digital converters (ADCs) and RF impairments respectively. We show that hardware impairments cause a nonzero floor on the channel estimation error, which contraries to the conventional case with ideal hardware. The maximal-ratio combining (MRC) technique is then …
Millimeter wave (mmWave) massive multiple-input multiple-output (massive MIMO) is one of the most promising technologies for the fifth generation and beyond wireless communication system. However, a large number of antennas incur high power consumption and hardware costs, and high-frequency communications place a heavy burden on the analog-to-digital converters (ADCs) at the base station (BS). Furthermore, it is too costly to equipping each antenna with a high-precision ADC in a large antenna array system. It is promising to adopt low-resolution ADCs to address this problem. In this paper, we …
This paper considers the channel estimation problem for massive multiple-input multiple-output (MIMO) systems that use one-bit analog-to-digital converters (ADCs). Previous channel estimation techniques for massive MIMO using one-bit ADCs are all based on single-shot estimation without exploiting the inherent temporal correlation in wireless channels. In this paper, we propose an adaptive channel estimation technique taking the spatial and temporal correlations into account for massive MIMO with one-bit ADCs. We first use the Bussgang decomposition to linearize the one-bit quantized received s…
This paper considers an uplink multiuser multiple-input-multiple-output (MU-MIMO) system with one-bit analog-to-digital converters (ADCs), in which $K$ users with a single transmit antenna communicate with one base station (BS) with $N_{\rm r}$ receive antennas. In this system, a novel MU-MIMO detection method, named weighted minimum distance (wMD) decoding, was recently proposed by introducing an equivalent coding problem. Despite of its attractive performance, the wMD decoding has the two limitations to be used in practice: i) the hard-decision outputs can degrade the performance of a channe…
Fixed low-resolution Analog to Digital Converters (ADC) help reduce the power consumption in millimeter-wave Massive Multiple-Input Multiple-Output (Ma-MIMO) receivers operating at large bandwidths. However, they do not guarantee optimal Energy Efficiency (EE). It has been shown that adopting variable-resolution (VR) ADCs in Ma-MIMO receivers can improve performance with Mean Squared Error (MSE) and throughput while providing better EE. In this paper, we present an optimal energy-efficient bit allocation (BA) algorithm for Ma-MIMO receivers equipped with VR ADCs under a power constraint. We de…
In this paper, we derive an optimal ADC bit-allocation (BA) condition for a Single-User (SU) Millimeter wave (mmWave) Massive Multiple-Input Multiple-Output (Ma-MIMO) receiver equipped with variable-resolution ADCs under power constraint with the following criteria: (i) Minimizing the Mean Squared Error (MSE) of the received, quantized and combined symbol vector and (ii) Maximizing the capacity of the SU mmWave Ma-MIMO channel encompassing hybrid precoder and combiner. Optimal BA under both criteria results the same. We jointly design the hybrid combiner based on the SVD of the channel. We dem…
This paper considers a multiple-input-multiple-output (MIMO) system with low-resolution analog-to-digital converters (ADCs). In this system, we propose a novel communication framework that is inspired by supervised learning. The key idea of the proposed framework is to learn the non-linear input-output system, formed by the concatenation of a wireless channel and a quantization function used at the ADCs, for data detection. In this framework, a conventional channel estimation process is replaced by a system learning process, in which the conditional probability mass functions (PMFs) of the non…
