Wireless Sensor Networks (WSNs) are being used in various applications such as structural health monitoring and industrial control. Since energy efficiency is one of the major design factors, the existing WSNs primarily rely on low-power, low-rate wireless technologies such as 802.15.4 and Bluetooth. In this paper, we strive to tackle the challenges of developing ultra-high-rate WSNs based on 802.11 (WiFi) standard by proposing Sensifi. As an illustrative application of this system, we consider vibration test monitoring of spacecraft and identify system design requirements and challenges. Our main contributions are as follows. First, we propose packet encoding methods to reduce the overhead of assigning accurate timestamps to samples. Second, we propose energy efficiency methods to enhance the system's lifetime. Third, we reduce the overhead of processing outgoing packets through network stack to enhance sampling rate and mitigate sampling rate instability. Fourth, we study and reduce the delay of processing incoming packets through network stack to enhance the accuracy of time synchronization among nodes. Fifth, we propose a low-power node design for ultra-high-rate applications. Sixth, we use our node design to empirically evaluate the system.
Heterogeneous ultra-dense networks enable ultra-high data rates and ultra-low latency through the use of dense sub-6 GHz and millimeter wave (mmWave) small cells with different antenna configurations. Existing work has widely studied spectral and energy efficiency in such networks and shown that high spectral and energy efficiency can be achieved. This article investigates the benefits of heterogeneous ultra-dense network architecture from the perspectives of three promising technologies, i.e., physical layer security, caching, and wireless energy harvesting, and provides enthusiastic outlook …
Wireless networks are becoming extremely pervasive while traffic demand is ever increasing. In order to cope with the forecast increase in traffic volume for the upcoming years, as well as the number of connected devices, new technologies, practices and spectrum rearrangements are required. In this context, a key question arises: how to provide extensive backhaul connectivity and capacity for pervasive ultra dense networks? The answer is rather complex, if feasible. To shed some light into this issue we overview potential technologies, either wired or wireless, and identify technical challenge…
This paper describes a detailed performance evaluation of distributed Medium Access Control (MAC) protocols for Wireless Sensor Networks based on Impulse Radio Ultra Wideband (IR-UWB) Physical layer (PHY). Two main classes of Medium Access Control protocol have been considered: Slotted and UnSlotted with reliability. The reliability is based on Automatic Repeat ReQuest (ARQ). The performance evaluation is performed using a complete Wireless Sensor Networks (WSN) simulator built on the Global Mobile Information System Simulator (GloMoSim). The optimal operating parameters are first discussed fo…
The future connectivity landscape and, notably, the 5G wireless systems will feature Ultra-Reliable Low Latency Communication (URLLC). The coupling of high reliability and low latency requirements in URLLC use cases makes the wireless access design very challenging, in terms of both the protocol design and of the associated transmission techniques. This paper aims to provide a broad perspective on the fundamental tradeoffs in URLLC as well as the principles used in building access protocols. Two specific technologies are considered in the context of URLLC: massive MIMO and multi-connectivity, …
Impulse Radio Ultra Wide Band (IR-UWB) is a promising technology to address Wireless Sensor Network (WSN) constraints. However, existing network simulation tools do not provide a complete WSN simulation architecture, with the IR-UWB specificities at the PHYsical (PHY) and the Medium Access Control (MAC) layers. In this paper, we propose a WSN simulation architecture based on the IR-UWB technique. At the PHY layer, we take into account the pulse collision by dealing with the pulse propagation delay. We also modelled MAC protocols specific to IRUWB, for WSN applications. To completely fit the WS…
This paper proposes and demonstrates a PHY-layer design of a real-time prototype that supports Ultra-Reliable Communication (URC) in wireless infrastructure networks. The design makes use of Orthogonal Frequency Division Multiple Access (OFDMA) as a means to achieve URC. Compared with Time-Division Multiple Access (TDMA), OFDMA concentrates the transmit power to a narrower bandwidth, resulting in higher effective SNR. Compared with Frequency-Division Multiple Access (FDMA), OFDMA has higher spectrum efficiency thanks to the smaller subcarrier spacing. Although OFDMA has been introduced in 802.…
Wireless 5G systems will not only be "4G, but faster". One of the novel features discussed in relation to 5G is Ultra-Reliable Communication (URC), an operation mode not present in today's wireless systems. URC refers to provision of certain level of communication service almost 100 % of the time. Example URC applications include reliable cloud connectivity, critical connections for industrial automation and reliable wireless coordination among vehicles. This paper puts forward a systematic view on URC in 5G wireless systems. It starts by analyzing the fundamental mechanisms that constitute a …
Throughput capacity is a critical parameter for the design and evaluation of ad-hoc wireless networks. Consider n identical randomly located nodes, on a unit area, forming an ad-hoc wireless network. Assuming a fixed per node transmission capability of T bits per second at a fixed range, it has been shown that the uniform throughput capacity per node r(n) is Theta((T)/(sqrt{n log n})), a decreasing function of node density n. However an alternate communication model may also be considered, with each node constrained to a maximum transmit power P_0 and capable of utilizing W Hz of bandwidth. Un…
This paper presents a performance evaluation of Wireless Sensor Networks (WSN) based on Impulse Radio Ultra Wideband (IR-UWB) over a new simulation platform developed for this purpose. The simulation platform is built on an existing network simulator: Global Mobile Information System Simulator (GloMoSim). It mainly focuses on the accurately modeling of IR-UWB PHYsical (PHY) and Medium Access Control (MAC) layer. Pulse collision is modeled according to the used time hopping sequence (THS) and the pulse propagation delay in order to increase the simulation fidelity. It also includes a detection …
This paper compares two models for delivering broadband wireless services: best effort vs. QoS guaranteed services. The 'best effort' services we refer to in this paper are more commonly known as unlicensed wireless services, while the 'Quality of Service guaranteed' services are more commonly referred to as traditional landline telephony, as well as cellular telephone services of either the second or third generation. This paper highlights the differing 'market' versus 'engineering' philosophies implicit in alternative wireless service architectures.
Ultra-low latency supported by the fifth generation (5G) give impetus to the prosperity of many wireless network applications, such as autonomous driving, robotics, telepresence, virtual reality and so on. Ultra-low latency is not achieved in a moment, but requires long-term evolution of network structure and key enabling communication technologies. In this paper, we provide an evolutionary overview of low latency in mobile communication systems, including two different evolutionary perspectives: 1) network architecture; 2) physical layer air interface technologies. We firstly describe in deta…
Ultra-Reliable Low Latency Communication (URLLC) is one of the distinctive features of the upcoming 5G wireless communication, going down to packet error rates (PER) of $10^{-9}$. In this paper we discuss the statistical properties of the wireless channel models that are relevant for characterization of the lower tail of the Cumulative Distribution Function (CDF). We show that, for a wide range of channel models, the outage probability at URLLC levels can be approximated by a simple power law expression, whose exponent and offset depend on the actual channel model. The main insights from the a…
The extreme traffic load that future wireless networks are expected to accommodate requires a re-thinking of the system design. Initial estimations indicate that, different from the evolutionary path of previous cellular generations that was based on spectral efficiency improvements, the most substantial amount of future system performance gains will be obtained by means of network infrastructure densification. By increasing the density of operator-deployed infrastructure elements, along with incorporation of user-deployed access nodes and mobile user devices acting as "infrastructure prosumer…
Next-generation wireless networks must enable emerging technologies such as augmented reality and connected autonomous vehicles via wide range of wireless services that span enhanced mobile broadband (eMBB), as well as ultra-reliable low-latency communication (URLLC). Existing wireless systems that solely rely on the scarce sub-6 GHz, microwave ($μ$W) frequency bands will be unable to meet such stringent and mixed service requirements for future wireless services due to spectrum scarcity. Meanwhile, operating at high-frequency millimeter wave (mmWave) bands is seen as an attractive solution, p…
Ultra-reliable low latency communication (URLLC) is an important new feature brought by 5G, with a potential to support a vast set of applications that rely on mission-critical links. In this article, we first discuss the principles for supporting URLLC from the perspective of the traditional assumptions and models applied in communication/information theory. We then discuss how these principles are applied in various elements of the system design, such as use of various diversity sources, design of packets and access protocols. The important messages are that there is a need to optimize the t…
It has become increasingly clear that the current design paradigm for mobile broadband systems is not a scalable and economically feasible way to solve the expected future 'capacity crunch', in particular in indoor locations with large user densities. 'Moore's law', e.g. state-of-the art signal processing and advanced antenna techniques now being researched, as well as more millimeter wave spectrum indeed provide more capacity, but are not the answer to the 3-4 orders of magnitude more capacity at today's cost, that is needed.We argue that solving the engineering problem of providing high data…
The next 5 th generation (5G) and above ultra-high speed, ultra-low latency, and extremely high reliable communication systems will consist of heterogeneous networks. These heterogeneous networks will consist not only radio frequency (RF) based systems but also optical wireless based systems. Hybrid architectures among different networks is an excellent approach for achieving the required level of service quality. In this paper, we provide the opportunities bring by hybrid systems considering RF as well as optical wireless based communication technologies. We also discuss about the key researc…
Ultra network densification is considered a major trend in the evolution of cellular networks, due to its ability to bring the network closer to the user side and reuse resources to the maximum extent. In this paper we explore spatial resources coordination as a key empowering technology for next generation (5G) ultra-dense networks. We propose an optimization framework for flexibly associating system users with a densely deployed network of access nodes, opting for the exploitation of densification and the control of overhead signaling. Combined with spatial precoding processing strategies, w…
Coming cellular systems are envisioned to open up to new services with stringent reliability and energy efficiency requirements. In this paper we focus on the joint power control and rate allocation problem in Single-Input Multiple-Output (SIMO) wireless systems with Rayleigh fading and stringent reliability constraints. We propose an allocation scheme that maximizes the energy efficiency of the system while making use only of average statistics of the signal and interference, and the number of antennas $M$ that are available at the receiver side. We show the superiority of the Maximum Ratio C…
Ultra network densification and Massive MIMO are considered major 5G enablers since they promise huge capacity gains by exploiting proximity, spectral and spatial reuse benefits. Both approaches rely on increasing the number of access elements per user, either through deploying more access nodes over an area or increasing the number of antenna elements per access node. At the network-level, optimal user-association for a densely and randomly deployed network of Massive MIMO empowered access nodes must account for both channel and load conditions. In this paper we formulate this complex problem…
The 5th generation (5G) wireless access technology, known as new radio (NR), will address a variety of usage scenarios from enhanced mobile broadband to ultra-reliable low-latency communications to massive machine type communications. Key technology features include ultra-lean transmission, support for low latency, advanced antenna technologies, and spectrum flexibility including operation in high frequency bands and inter-working between high and low frequency bands. This article provides an overview of the essentials of the state of the art in 5G wireless technology represented by the 3GPP N…
In 5G Ultra-Dense Networks, a distributed wireless backhaul is an attractive solution for forwarding traffic to the core. The macro-cell coverage area is divided into many small cells. A few of these cells are designated as gateways and are linked to the core by high-capacity fiber optic links. Each small cell is associated with one gateway and all small cells forward their traffic to their respective gateway through multi-hop mesh networks. We investigate the gateway location problem and show that finding near-optimal gateway locations improves the backhaul network capacity. An exact p-median…
This article provides dives into the fundamentals of dense and ultra-dense small cell wireless networks, discussing the reasons why dense and ultra-dense small cell networks are fundamentally different from sparse ones, and why the well-known linear scaling law of capacity with the base station (BS) density in the latter does not apply to the former. In more detail, we review the impact of the following factors on ultradense networks (UDNs), (i) closed-access operations and line-of-sight conditions, (ii) the near-field effect, (iii) the antenna height difference between small cell BSs and user…
For high data rate ultra wideband communication system, performance comparison of Rake, MMSE and Rake-MMSE receivers is attempted in this paper. Further a detail study on Rake-MMSE time domain equalizers is carried out taking into account all the important parameters such as the effect of the number of Rake fingers and equalizer taps on the error rate performance. This receiver combats inter-symbol interference by taking advantages of both the Rake and equalizer structure. The bit error rate performances are investigated using MATLAB simulation on IEEE 802.15.3a defined UWB channel models. Sim…
In this paper, we study the cell planning problem for a two-tier cellular network containing two types of base stations (BSs)-- i.e. with fiber backhaul, referred to as wired BSs (W-BSs), and BSs with wireless backhaul, referred to as unwired-BSs (U-BSs). In-band full-duplex wireless communications is used to connect U-BSs and W-BSs. We propose an algorithm to determine the minimum number of W-BSs and U-BSs to satisfy given cell and capacity coverage constraints. Furthermore, we apply our proposed non-dominated sorting genetic algorithm II (NSGA-II) to solve both cell planning and joint cell a…
Achieving end-to-end ultra-reliability and resiliency in mission critical communications is a major challenge for future wireless networks. Dual connectivity has been proposed by 3GPP as one of the viable solutions to fulfill the reliability requirements. However, the potential correlation in failures occurring over different wireless links is commonly neglected in current network design approaches. In this paper, we investigate the impact of realistic correlation among different wireless links on end-to-end reliability for two selected architectures from 3GPP. In ultra-reliable use-cases, we …
University of Piraeus（比雷埃夫斯大学）；RapidMiner GmbH（RapidMiner有限公司）；Nokia Standardization Department（诺基亚标准化部）；Université Paris-Saclay（巴黎萨克雷大学）；CNRS（法国国家科学研究中心）；CentraleSupélec（巴黎中央理工-高等电力学院）
Terahertz (THz) wireless networks are expected to catalyze the beyond fifth generation (B5G) era. However, due to the directional nature and the line-of-sight demand of THz links, as well as the ultra-dense deployment of THz networks, a number of challenges that the medium access control (MAC) layer needs to face are created. In more detail, the need of rethinking user association and resource allocation strategies by incorporating artificial intelligence (AI) capable of providing "real-time" solutions in complex and frequently changing environments becomes evident. Moreover, to satisfy the ul…
This paper studies the effect of bandwidth partitioning (BWP) on the reliability and delay performance in infrastructureless wireless networks. The reliability performance is characterized by the density of concurrent transmissions that satisfy a certain reliability (outage) constraint and the delay performance by so-called local delay, defined as the average number of time slots required to successfully transmit a packet. We concentrate on the ultrareliable regime where the target outage probability is close to 0. BWP has two conflicting effects: while the interference is reduced as the concu…
Several researches are focused on the QoS (Quality of Service) and Energy consumption in wireless Multimedia Sensor Networks. Those research projects invest in theory and practice in order to extend the spectrum of use of norms, standards and technologies which are emerged in wireless communications. The performance of these technologies is strongly related to domains of use and limitations of their characteristics. In this paper, we give a comparison of ZigBee technology, most widely used in sensor networks, and UWB (Ultra Wide Band) which presents itself as competitor that present in these w…
Mission critical Machine-type Communication, also referred to as Ultra-reliable Low Latency Communication is primarily characterized by communication that provides ultra-high reliability and very low latency to concurrently transmit short commands to a massive number of connected devices. While the reduction in PHY layer overhead and improvement in channel coding techniques are pivotal in reducing latency and improving reliability, the current wireless standards dedicated to support mcMTC rely heavily on adopting the bottom layers of general-purpose wireless standards and customizing only the …
Internet of things is in progress to build a smart society, and wireless networks are critical enablers for many of its use cases. In this paper, we present a multi-coordinated transmission scheme to achieve ultra-reliability for critical machine-type wireless communication networks. We take advantage of diversity, which is fundamental for dealing with fading channel impairments, and for achieving ultra-reliable region of operation in order of five 9's as defined by 3GPP standardization bodies. We evaluate an interference-limited network composed of multiple remote radio heads that are allowed…
The wireless backhaul network provides an attractive solution for the urban deployment of fifth generation (5G) wireless networks that enables future ultra dense small cell networks to meet the ever-increasing user demands. Optimal deployment and management of 5G wireless backhaul networks is an interesting and challenging issue. In this paper we propose the optimal gateways deployment and wireless backhaul route schemes to maximize the cost efficiency of 5G wireless backhaul networks. In generally, the changes of gateways deployment and wireless backhaul route are presented in different time …
Enabling ultra-reliable low latency communications (uRLLC) over 5G wireless networks creates challenging design requirements, particularly on the air-interface. The stringent latency and reliability targets require enhancements at different layers of the protocol stack. On the other hand, the parallel redundancy protocol (PRP), wherein each data packet is duplicated and transmitted concurrently over two independent networks, provides a simple solution for improving reliability and reducing latency in wireless networks. PRP can be realized in cellular networks through the dual connectivity (DC)…
Multi-connectivity offers diversity in terms of multiple interfaces through which the data can be sent, thereby improving simultaneously the overall reliability and latency. This makes interface diversity a natural candidate for supporting Ultra-Reliable Low Latency Communications (URLLC). This work investigates how the packet error statistics from different interfaces impacts the overall reliability-latency characteristics. We use the simple Gilbert-Elliott model for burst errors and estimate its parameters based on experimental measurement traces from LTE and {Wi-Fi} packet transmissions col…
This paper addresses the radio interface problematic for MANET (Mobile Ad-hoc NETwork) applications. Here we propose to study the radio reconfigurability in order to provide a unique physical layer which is able to deal with all MANET applications. For implementing this reconfigurable physical layer, we propose to use Impulse Radio Ultra WideBand (IRUWB). This paper presents also our two level design approach for obtaining our reconfigurable IR-UWB receiver on FPGA (Field Programmable Gate Array).
In this paper,a new design of wireless sensor network (WSN)node is discussed which is based on components with ultra low power.We ha e de eloped a Low cost and low power WSN Node using MSP430 and nRF24L01.The architectural circuit details are presented.This architecture fulfils the requirements like low cost,low power,compact size and self organization.Various tests are carried out to test the performance of the nRF24L01 module.The packet loss,free Space loss (FSL)and battery lifetime calculations are described.These test results will help the researchers to build new applications using abo e …
Accurate wireless timing synchronization has been an extremely important topic in wireless sensor networks, required in applications ranging from distributed beam forming to precision localization and navigation. However, it is very challenging to realize, in particular when the required accuracy should be better than the runtime between the nodes. This work presents, to our knowledge for the first time, an experimental timing synchronization scheme that achieves a timing accuracy better than 5ns rms in a network with 4 nodes. The experimental hardware is built from commercially available comp…
Wireless Sensor Networks (WSNs) have gained worldwide attention in recent years, particularly with the proliferation in Micro-Electro-Mechanical Systems (MEMS) technology which has facilitated the development of smart sensors. The paper discusses about classification of WSN and challenges of the Next Generation WSN. One of the major challenges of Next Generation WSN is reduction of power consumption. The two approaches are discussed: Ultra-Low-Power Networks and Energy Harvesting. The paper also discusses about some major applications as designing low cost secured Intelligent Buildings, In-Hom…
To date, model-based reliable communication with low latency is of paramount importance for time-critical wireless control systems. In this work, we study the downlink (DL) controller-to-actuator scheduling problem in a wireless industrial network such that the outage probability is minimized. In contrast to the existing literature based on well-known stationary fading channel models, we assume an arbitrary and unknown channel fading model, which is available only via samples. To overcome the issue of limited data samples, we invoke the generative adversarial network framework and propose an o…
Ultra-reliable communication (URC) is a key enabler for supporting immersive and mission-critical 5G applications. Meeting the strict reliability requirements of these applications is challenging due to the absence of accurate statistical models tailored to URC systems. In this letter, the wireless connectivity over dynamic channels is characterized via statistical learning methods. In particular, model-based and data-driven learning approaches are proposed to estimate the non-blocking connectivity statistics over a set of training samples with no knowledge on the dynamic channel statistics. U…
The fifth generation (5G) of wireless systems holds the promise of supporting a wide range of services with different communication requirements. Ultra-reliable low-latency communications (URLLC) is a generic service that enables mission-critical applications, such as industrial automation, augmented reality, and vehicular communications. URLLC has stringent requirements for reliability and latency of delivering both data and control information. In order to meet these requirements, the Third Generation Partnership Project (3GPP) has been introducing new features to the upcoming releases of th…
5G wireless networks are expected to support Ultra Reliable Low Latency Communications (URLLC) traffic which requires very low packet delays ( < 1 msec.) and extremely high reliability ($\sim$99.999\%). In this paper we focus on the design of a wireless system supporting downlink URLLC traffic. Using a queuing network based model for the wireless system we characterize the effect of various design choices on the maximum URLLC load it can support, including: 1) system parameters such as the bandwidth, link SINR , and QoS requirements; 2) resource allocation schemes in Orthogonal Frequency Divis…
This paper studies the power allocation of an ultra-dense cellular network consisting of multiple full-duplex (FD) base stations (BSs) serving a large number of half-duplex (HD) user equipments (UEs) located in a wide geographical area. Each BS consists of a baseband unit (BBU) that is responsible for signal processing and base station control, and a radio remote unit (RRU) that corresponds to a radio transceiver remotely built closer to the UEs. We consider a wireless-powered cellular network in which the BBU can periodically charge the RRU. We model the energy efficiency and coverage optimiz…
Emerging 5G and next generation 6G wireless are likely to involve myriads of connectivity, consisting of a huge number of relatively smaller cells providing ultra-dense coverage. Guaranteeing seamless connectivity and service level agreements in such a dense wireless system demands efficient network management and fast service recovery. However, restoration of a wireless network, in terms of maximizing service recovery, typically requires evaluating the service impact of every network element. Unfortunately, unavailability of real-time KPI information, during an outage, enforces most of the ex…
Wireless on-chip communication is a promising candidate to address the performance and efficiency issues that arise when scaling current Network-on-Chip (NoC) techniques to manycore processors. A Wireless Network-on-Chip (WNoC) can serve global and broadcast traffic with ultra-low latency even in thousand-core chips, thus acting as a natural complement of conventional and throughput-oriented wireline NoCs. However, the development of Medium Access Control (MAC) strategies needed to efficiently share the wireless medium among the increasing number of cores remains as a considerable challenge gi…
Driven by new types of wireless devices and the proliferation of bandwidth-intensive applications, data traffic and the corresponding network load are increasing dramatically. Network densification has been recognized as a promising and efficient way to provide higher network capacity and enhanced coverage. Most prior work on performance analysis of ultra-dense networks (UDNs) has focused on random spatial deployment with idealized singular path loss models and Rayleigh fading. In this paper, we consider a more precise and general model, which incorporates multi-slope path loss and general fad…
Ultra-reliability and low-latency are pivotal requirements of the new 6th generation of communication systems (xURLLC). Over the past years, to increase throughput, adaptive active antennas were introduced in advanced wireless communications, specifically in the domain of millimeter-wave (mmWave). Consequently, new lower-layer techniques were proposed to cope with practical challenges of high dimensional and electronically-steerable beams. The transition from omni-directional to highly directional antennas presents a new type of wireless systems that deliver high bandwidth, but that are suscep…
In this article, we first present the vision, key performance indicators, key enabling techniques (KETs), and services of 6G wireless networks. Then, we highlight a series of general resource management (RM) challenges as well as unique RM challenges corresponding to each KET. The unique RM challenges in 6G necessitate the transformation of existing optimization-based solutions to artificial intelligence/machine learning-empowered solutions. In the sequel, we formulate a joint network selection and subchannel allocation problem for 6G multi-band network that provides both further enhanced mobi…
The 5G Phase-2 and beyond wireless systems will focus more on vertical applications such as autonomous driving and industrial Internet-of-things, many of which are categorized as ultra-Reliable Low-Latency Communications (uRLLC). In this article, an alternative view on uRLLC is presented, that information latency, which measures the distortion of information resulted from time lag of its acquisition process, is more relevant than conventional communication latency of uRLLC in wireless networked control systems. An AI-assisted Situationally-aware Multi-Agent Reinforcement learning framework for…
This article explores the concepts of online protocol synthesis using Reinforcement Learning (RL). The study is performed in the context of sensor and IoT networks with ultra low complexity wireless transceivers. The paper introduces the use of RL and Multi Armed Bandit (MAB), a specific type of RL, for Medium Access Control (MAC) under different network and traffic conditions. It then introduces a novel learning based protocol synthesis framework that addresses specific difficulties and limitations in medium access for both random access and time slotted networks. The mechanism does not rely …
Virtual reality (VR) enables mobile wireless users to experience multimodal perceptions in a virtual space. In this paper we investigate the problem of concurrent support of visual and haptic perceptions over wireless cellular networks, with a focus on the downlink transmission phase. While the visual perception requires moderate reliability and maximized rate, the haptic perception requires fixed rate and high reliability. Hence, the visuo-haptic VR traffic necessitates the use of two different network slices: enhanced mobile broadband (eMBB) for visual perception and ultra-reliable and low l…
