The Jellyfish network has recently be proposed as an alternate to the fat-tree network as the interconnect for data centers and high performance computing clusters. Jellyfish adopts a random regular graph as its topology and has been showed to be more cost-effective than fat-trees. Effective routing on Jellyfish is challenging. It is known that shortest path routing and equal-cost multi-path routing (ECMP) do not work well on Jellyfish. Existing schemes use variations of k-shortest path routing (KSP). In this work, we study two routing components for Jellyfish: path selection that decides the paths to route traffic, and routing mechanisms that decide which path to be used for each packet. We show that the performance of the existing KSP can be significantly improved by incorporating two heuristics, randomization and edge-disjointness. We evaluate a range of routing mechanisms including traffic oblivious and traffic adaptive schemes and identify an adaptive routing scheme that has significantly higher performance than others including the Universal Globally Adaptive Load-balance (UGAL) routing.
Industry experience indicates that the ability to incrementally expand data centers is essential. However, existing high-bandwidth network designs have rigid structure that interferes with incremental expansion. We present Jellyfish, a high-capacity network interconnect, which, by adopting a random graph topology, yields itself naturally to incremental expansion. Somewhat surprisingly, Jellyfish is more cost-efficient than a fat-tree: A Jellyfish interconnect built using the same equipment as a fat-tree, supports as many as 25% more servers at full capacity at the scale of a few thousand nodes…
The recent line of research into topology design focuses on lowering network diameter. Many low-diameter topologies such as Slim Fly or Jellyfish that substantially reduce cost, power consumption, and latency have been proposed. A key challenge in realizing the benefits of these topologies is routing. On one hand, these networks provide shorter path lengths than established topologies such as Clos or torus, leading to performance improvements. On the other hand, the number of shortest paths between each pair of endpoints is much smaller than in Clos, but there is a large number of non-minimal …
In Kleinrock and Kamoun's paper, the inverse relation of routing table length index and routing path length index in hierarchical routing model is illustrated. In this paper we give the analytical correlation of routing table length index and routing path length index in hierarchical routing model.
We study {\em routing} and {\em scheduling} in packet-switched networks. We assume an adversary that controls the injection time, source, and destination for each packet injected. A set of paths for these packets is {\em admissible} if no link in the network is overloaded. We present the first on-line routing algorithm that finds a set of admissible paths whenever this is feasible. Our algorithm calculates a path for each packet as soon as it is injected at its source using a simple shortest path computation. The length of a link reflects its current congestion. We also show how our algorithm …
Routing in Wireless Sensor Network (WSN) aims to interconnect sensor nodes via single or multi-hop paths. The routes are established to forward data packets from sensor nodes to the sink. Establishing a single path to report each data packet results in increasing energy consumption in WSN, hence, data aggregation routing is used to combine data packets and consequently reduce the number of transmissions. This reduces the routing overhead by eliminating redundant and meaningless data. There are two models for data aggregation routing in WSN: mobile agent and client/server. This paper describes …
Internet is composed of numbers of independent autonomous systems. BGP is used to disseminate reachability information and establishing path between autonomous systems. Each autonomous system is allowed to select a single route to a destination and then export the selected route to its neighbors. The selection of single best route imposes restrictions on the use of alternative paths during interdomain link failure and thus, incurred packet loss. Packet loss still occurs even when multiple paths exist between source and destination but these paths have not been utilized. To minimize the packet …
Today's communication networks have stringent availability requirements and hence need to rapidly restore connectivity after failures. Modern networks thus implement various forms of fast reroute mechanisms in the data plane, to bridge the gap to slow global control plane convergence. State-of-the-art fast reroute commonly relies on disjoint route structures, to offer multiple independent paths to the destination. We propose to leverage the network's path diversity to extend edge disjoint path mechanisms to tree routing, in order to improve the performance of fast rerouting. We present two suc…
Unlike traditional routing procedures that, at the best, single out a unique route, multi-path routing protocols discover proactively several alternative routes. It has been recognized that multi-path routing can be more efficient than traditional one mainly for mobile ad hoc networks, where route failure events are frequent. Most studies in the area of multi-path routing focus on heuristic methods, and the performances of these strategies are commonly evaluated by numerical simulations. The need of a theoretical analysis motivates such a paper, which proposes to resort to the terminal-pair ro…
We consider wireless mesh networks and the problem of routing end-to-end traffic over multiple paths for the same origin-destination pair with minimal interference. We introduce a heuristic for path determination with two distinguishing characteristics. First, it works by refining an extant set of paths, determined previously by a single- or multi-path routing algorithm. Second, it is totally local, in the sense that it can be run by each of the origins on information that is available no farther than the node's immediate neighborhood. We have conducted extensive computational experiments with…
Most studies on path-vector routing stability have been conducted empirically by means of ad-hoc analysis of BGP data traces. None of them consider prior specification of an analytic method including the use of stability measurement metrics for the systematic analysis of BGP traces and associated meta-processing for determining the local state of the routing system. In this paper, we define a set of metrics that characterize the local stability properties of path-vector routing such as BGP (Border Gateway Protocol). By means of these stability metrics, we propose a method to analyze the effect…
Most studies on path-vector routing stability have been conducted empirically by means of ad-hoc analysis of BGP data traces. None of them consider prior specification of an analytic method including the use of stability measurement metrics for the systematic analysis of BGP traces and associated meta-processing for determining the local state of the routing system. In this paper, we define a set of metrics that characterize the local stability properties of path-vector routing such as BGP (Border Gateway Protocol). By means of these stability metrics, we propose a method to analyze the effect…
The high-level contribution of this paper is a simulation-based analysis to evaluate the tradeoffs between lifetime and hop count of link-disjoint, node-disjoint and zone-disjoint multi-path routes vis-à-vis single-path minimum hop routes for mobile ad hoc networks. The link-disjoint, node-disjoint and zone-disjoint algorithms proposed in this paper can be used to arrive at benchmarks for the time between successive multi-path route discoveries, the number of disjoint paths per multi-path set and the hop count per multi-path set. We assume a multi-path set exists as long as at least one path i…
Some multi-path routing algorithm in MANET, simultaneously send information to the destination through several directions to reduce end-to-end delay. In all these algorithms, the sent traffic through a path affects the adjacent path and unintentionally increases the delay due to the use of adjacent paths. Because, there are repetitive competitions among neighboring nodes, in order to obtain the joint channel in adjacent paths. The represented algorithm in this study tries to discover the distinct paths between source and destination nodes with using Omni directional antennas, to send informati…
The greedy strategy of geographical routing may cause the local minimum problem when there is a hole in the routing area. It depends on other strategies such as perimeter routing to find a detour path, which can be long and result in inefficiency of the routing protocol. In this paper, we propose a new approach called Intermediate Target based Geographic Routing (ITGR) to solve the long detour path problem. The basic idea is to use previous experience to determine the destination areas that are shaded by the holes. The novelty of the approach is that a single forwarding path can be used to det…
The main challenge in wireless sensor network is to improve the fault tolerance of each node and also provide an energy efficient fast data routing service. In this paper we propose an energy efficient node fault diagnosis and recovery for wireless sensor networks referred as fault tolerant multipath routing scheme for energy efficient wireless sensor network (FTMRS).The FTMRS is based on multipath data routing scheme. One shortest path is use for main data routing in FTMRS technique and other two backup paths are used as alternative path for faulty network and to handle the overloaded traffic…
The performances of the routing protocols are important since they compute the primary path between source and destination. In addition, routing protocols need to detect failure within a short period of time when nodes move to start updating the routing table in order to find a new primary path to the destination. Meantime, loss of packets and end-to- end delays will increase thereby reducing throughput and degrading the performance of the network. This paper proposes a new algorithm, DBRT (Driven Backup Routing Table), to improve the existing proactive protocols such as DSDV (Destination Sequ…
Enabling real time applications in wireless sensor networks requires certain delay and bandwidth which pose more challenges in the design of routing protocols. The algorithm that is used for packet routing in such applications should be able to establish a tradeoff between end to end delay parameter and energy consumption. In this paper, we propose a new multi path routing algorithm for real time applications in wireless sensor networks namely QEMPAR which is QoS aware and can increase the network lifetime. Simulation results show that the proposed algorithm is more efficient than previous alg…
A reliable network infrastructure must be able to sustain traffic flows, even when a failure occurs and changes the network topology. During the occurrence of a failure, routing protocols, like OSPF, take from hundreds of milliseconds to various seconds in order to converge. During this convergence period, packets might traverse a longer path or even a loop. An even worse transient behaviour is that packets are dropped even though destinations are reachable. In this context, this paper describes a proactive fast rerouting approach, named Fast Emergency Paths Schema (FEP-S), to overcome problem…
In optical WDM networks, transmission of information along optical lines is advantageous since it has high transmission capacity, scalability, feasibility and also high reliability. But large amount of information is being carried; any problem during transmission can lead to severe damage to the data being carried. Hence it is essential to consider the routing as well as the wavelength assignment problems and then develop a combined solution for both the problems. In this paper, we propose to develop a routing and wavelength assignment algorithm for selecting the suitable alternate path for th…
In this paper we present a methodology employing statistical analysis and stochastic geometry to study geometric routing schemes in wireless ad-hoc networks. In particular, we analyze the network layer performance of one such scheme, the random $\frac{1}{2}$disk routing scheme, which is a localized geometric routing scheme in which each node chooses the next relay randomly among the nodes within its transmission range and in the general direction of the destination. The techniques developed in this paper enable us to establish the asymptotic connectivity and the convergence results for the mea…
Information-Centric Networking is still an incomplete paradigm which introduces a large variety of new topics and approaches over the traditional networking. Since it is a relatively new concept which promises for easier and faster data access many aspects of it have been studied intensely in recent years. Nonetheless, load balancing is one of the least focused but high potency, open-ended areas. The aim of this project is to present an alternative technique to load balancing in the domain of pre-suggested routing method LSCR (Link State Content Routing). We suggested multi-path interest and m…
Internal routing inside an ISP network is the foundation for lots of services that generate revenue from the ISP's customers. A fine-grained control of paths taken by network traffic once it enters the ISP's network is therefore a crucial means to achieve a top-quality offer and, equally important, to enforce SLAs. Many widespread network technologies and approaches (most notably, MPLS) offer limited (e.g., with RSVP-TE), tricky (e.g., with OSPF metrics), or no control on internal routing paths. On the other hand, recent advances in the research community are a good starting point to address t…
We investigate the design of the optimal routing path in a moving vehicles involved the internet of things (IoT). In our model, jammers exist that may interfere with the information exchange between wireless nodes, leading to worsened quality of service (QoS) in communications. In addition, the transmit power of each battery-equipped node is constrained to save energy. We propose a three-step optimal routing path algorithm for reliable and energy-efficient communications. Moreover, results show that with the assistance of moving vehicles, the total energy consumed can be reduced to a large ext…
Several emerging classes of applications that run over wireless networks have a need for mathematical models and tools to systematically characterize the reliability of the network. We propose two metrics for measuring the reliability of wireless mesh routing topologies, one for flooding and one for unicast routing. The Flooding Path Probability (FPP) metric measures the end-to-end packet delivery probability when each node broadcasts a packet after hearing from all its upstream neighbors. The Unicast Retransmission Flow (URF) metric measures the end-to-end packet delivery probability when a r…
Erasure resilient FEC codes in off-line packetized streaming rely on time diversity. This requires unrestricted buffering time at the receiver. In real-time streaming the playback buffering time must be very short. Path diversity is an orthogonal strategy. However, the large number of long paths increases the number of underlying links and consecutively the overall link failure rate. This may increase the overall requirement in redundant FEC packets for combating the link failures. We introduce the Redundancy Overall Requirement (ROR) metric, a routing coefficient specifying the total number o…
This paper presents a scalability and load balancing study of the All-Path protocols, a family of distributed switching protocols based on path exploration. ARP-Path is the main protocol and it explores every possible path reaching from source to destination by using ARP messages, selecting the lowest latency path. Flow-Path and Bridge-Path are respectively the flow-based and bridge-based versions, instead of the source address-based approach of ARP-Path. While preserving the main advantages of ARP-Path, Flow-Path has the advantages of full independence of flows for path creation, guaranteeing…
In this paper, we consider the problem of finding the maximum routing throughput between any pair of nodes in an arbitrary multirate wireless mesh network (WMN) using multiple paths. Multipath routing is an efficient technique to maximize routing throughput in WMN, however maximizing multipath routing throughput is a NP-complete problem due to the shared medium for electromagnetic wave transmission in wireless channel, inducing collision-free scheduling as part of the optimization problem. In this work, we first provide problem formulation that incorporates collision-free schedule, and then ba…
Geocast is the concept of sending data packets to nodes in a specified geographical area instead of nodes with a specific address. To route geocast messages to their destination we need a geographic routing algorithm that can route packets efficiently to the devices inside the destination area. Our goal is to design an algorithm that can deliver shortest path tree like forwarding while relying purely on distributed data without central knowledge. In this paper, we present two algorithms for geographic routing. One based purely on distance vector data, and one more complicated algorithm based o…
Understanding how packets are routed in Internet is significantly important to Internet measurement and modeling. The conventional solution for route simulation is based on the assumption of unweighted shortest path. However, it has been found and widely accepted that a packet in Internet is usually not transmitted along the unweighted shortest path between its source and destination. To better simulate the routing behavior of a packet, we thoroughly explore the real-world Internet routes and present a novel local information based simulation model, with a tuning parameter, which assigns weigh…
In this paper, we present a new routing algorithm called "the Self Avoiding Paths Routing Algorithm". Its application to traffic flow in scale-free networks shows a great improvement over the so called "efficient routing" protocol while at the same time maintaining a relatively low average packet travel time. It has the advantage of minimizing path overlapping throughout the network in a self consistent manner with a relatively small number of iterations by maintaining an equilibrated path distribution especially among the hubs. This results in a significant shifting of the critical packet gen…
We present Contra, a system for performance-aware routing that can adapt to traffic changes at hardware speeds. While existing work has developed point solutions for performance-aware routing on a fixed topology (e.g., a Fattree) with a fixed routing policy (e.g., use least utilized paths), Contra can be configured to operate seamlessly over any network topology and a wide variety of sophisticated routing policies. Users of Contra write network-wide policies that rank network paths given their current performance. A compiler then analyzes such policies in conjunction with the network topology …
Wireless NanoSensor Network (WNSN) is a new type of sensor network with broad application prospects. In view of the limited energy of nanonodes and unstable links in WNSNs, we propose a reliable multi-path routing based on link stability (RMRLS). RMRLS selects the optimal path which perfects best in the link stability evaluation model, and then selects an alternative route by the routing similarity judgment model. RMRLS uses tew paths to cope with changes in the network topology. The simulation shows that the RMRLS protocol has advantages in data packet transmission success rate and average th…
Wide-area network traffic engineering enables network operators to reduce congestion and improve utilization by balancing load across multiple paths. Current approaches to traffic engineering can be modeled in terms of a routing component that computes forwarding paths, and a load balancing component that maps incoming flows onto those paths dynamically, adjusting sending rates to fit current conditions. Unfortunately, existing systems rely on simple strategies for one or both of these components, which leads to poor performance or requires making frequent updates to forwarding paths, signific…
Offchain networks emerge as a promising solution to address the scalability challenge of blockchain. Participants directly make payments through a network of payment channels without the overhead of committing onchain transactions. Routing is critical to the performance of offchain networks. Existing solutions use either static routing with poor performance or dynamic routing with high overhead to obtain the dynamic channel balance information. In this paper, we propose Flash, a new dynamic routing solution that leverages the unique characteristics of transactions in offchain networks to strik…
Locating the demanded content is one of the major challenges in Information-Centric Networking (ICN). This process is known as content discovery. To facilitate content discovery, in this paper we focus on Named Data Networking (NDN) and propose a novel routing scheme for content discovery, called Bloom Filter-based Routing (BFR), which is fully distributed, content oriented, and topology agnostic at the intra-domain level. In BFR, origin servers advertise their content objects using Bloom filters. We compare the performance of the proposed BFR with flooding and shortest path content discovery …
We study a class of robust network design problems motivated by the need to scale core networks to meet increasingly dynamic capacity demands. Past work has focused on designing the network to support all hose matrices (all matrices not exceeding marginal bounds at the nodes). This model may be too conservative if additional information on traffic patterns is available. Another extreme is the fixed demand model, where one designs the network to support peak point-to-point demands. We introduce a capped hose model to explore a broader range of traffic matrices which includes the above two as sp…
This paper proposes and evaluates a new position-based Parallel Routing Protocol (PRP) for simultaneously routing multiple data packets over disjoint paths in a mobile ad-hoc network (MANET) for higher reliability and reduced communication delays. PRP views the geographical region where the MANET is located as a virtual 2-dimensional grid of cells. Cell-disjoint (parallel) paths between grid cells are constructed and used for building pre-computed routing tables. A single gateway node in each grid cell handles routing through that grid cell reducing routing overheads. Each node maintains updat…
The Internet provides physical path diversity between a large number of hosts, making it possible for networks to use alternative paths when one path fails to deliver the required Quality of Service. However, for various reasons, many established protocols (e.g. de facto Internet inter-domain routing protocol, Border-Gateway Protocol - BGP) do not fully exploit such alternate paths. This paper surveys research into techniques for discovering end-to-end alternate paths, including those based on monitoring path performance, choosing paths that are maximally disjoint, and in routing across multip…
We introduce FatPaths: a simple, generic, and robust routing architecture that enables state-of-the-art low-diameter topologies such as Slim Fly to achieve unprecedented performance. FatPaths targets Ethernet stacks in both HPC supercomputers as well as cloud data centers and clusters. FatPaths exposes and exploits the rich ("fat") diversity of both minimal and non-minimal paths for high-performance multi-pathing. Moreover, FatPaths uses a redesigned "purified" transport layer that removes virtually all TCP performance issues (e.g., the slow start), and incorporates flowlet switching, a techni…
Maximum throughput requires path diversity enabled by bifurcating traffic at different network nodes. In this work, we consider a network where traffic bifurcation is allowed only at a subset of nodes called \emph{routers}, while the rest nodes (called \emph{forwarders}) cannot bifurcate traffic and hence only forward packets on specified paths. This implements an overlay network of routers where each overlay link corresponds to a path in the physical network. We study dynamic routing implemented at the overlay. We develop a queue-based policy, which is shown to be maximally stable (throughput…
In optical WDM networks, since each lightpath can carry a huge mount of traffic, failures may seriously damage the end user applications. Hence fault tolerance becomes an important issue on these networks. The light path which carries traffic during normal operation is called as primary path. The traffic is rerouted on a backup path in case of a failure. In this paper we propose to design a reliable and fault tolerant routing algorithm for establishing primary and backup paths. In order to establish the primary path, this algorithm uses load balancing in which link cost metrics are estimated b…
In off-line streaming, packet level erasure resilient Forward Error Correction (FEC) codes rely on the unrestricted buffering time at the receiver. In real-time streaming, the extremely short playback buffering time makes FEC inefficient for protecting a single path communication against long link failures. It has been shown that one alternative path added to a single path route makes packet level FEC applicable even when the buffering time is limited. Further path diversity, however, increases the number of underlying links increasing the total link failure rate, requiring from the sender pos…
Quantum networks are gaining momentum in finding applications in a wide range of domains. However, little research has investigated the potential of a quantum network framework to enable highly reliable communications. The goal of this work is to investigate and design the multiple-entanglement routing framework, namely k-entangled routing. In particular, the $k$-entangled routing will enable k paths connecting all demands (source-destination pairs) in the network. To design the $k$-entangled routing, we propose two algorithms that are called Sequential Multi-path Scheduling Algorithm and Min-…
We present PIE, a scalable routing scheme that achieves 100% packet delivery and low path stretch. It is easy to implement in a distributed fashion and works well when costs are associated to links. Scalability is achieved by using virtual coordinates in a space of concise dimensionality, which enables greedy routing based only on local knowledge. PIE is a general routing scheme, meaning that it works on any graph. We focus however on the Internet, where routing scalability is an urgent concern. We show analytically and by using simulation that the scheme scales extremely well on Internet-like…
Unlike classical routing algorithms, quantum routing algorithms make use of entangled states - a type of resources that have a limited lifetime and need to be regenerated after consumption. In a nutshell, quantum routing algorithms have to use these resources efficiently, while optimizing some objectives such as the total waiting time. Current routing algorithms tend to keep a routing request waiting until all of the resources on its path are available. In this paper, we introduce a new way of managing entanglement resources in an opportunistic fashion: a request can move forward along its pat…
In wireless sensor networks, bandwidth is one of precious resources to multimedia applications. To get more bandwidth, multipath routing is one appropriate solution provided that inter-path interferences are minimized. In this paper, we address the problem of interfering paths in the context of wireless multimedia sensor networks and consider both intra-session as well as inter-session interferences. Our main objective is to provide necessary bandwidth to multimedia applications through non-interfering paths while increasing the network lifetime. To do so, we adopt an incremental approach wher…
Quality of Service provisioning is one of the major design goals of IEEE 802.16 mesh networks. In order to provide quality delivery of delay sensitive services such as voice, video etc., it is required to route such traffic over a minimum delay path. In this paper we propose a routing metric for delay sensitive services in IEEE 802.16 mesh networks. We design a new cross layer routing metric, namely Expected Scheduler Delay (ESD), based on HoldOff exponent and the current load at each node of the network. This proposed metric takes into account the expected theoretical end-to-end delay of rout…
In this paper we compare the two intelligent route generation system and its performance capability in graded networks using Artificial Bee Colony (ABC) algorithm and Genetic Algorithm (GA). Both ABC and GA have found its importance in optimization technique for determining optimal path while routing operations in the network. The paper shows how ABC approach has been utilized for determining the optimal path based on bandwidth availability of the links and determines better quality paths over GA. Here the nodes participating in the routing are evaluated for their QoS metric. The nodes which s…
Realizing delay-capacity in intermittently connected mobile networks remains a largely open question, with state-of-the-art routing schemes typically focusing either on delay or on capacity. We show the feasibility of routing with both high goodput and desired delay constraints, with REAPER (for Reliable, Efficient, and Predictive Routing), a fully distributed convergecast routing framework that jointly optimizes both path length and path delay. A key idea for efficient instantiation of REAPER is to exploit predictability of mobility patterns, in terms of a semi-deterministic model which appro…
Current directions in network routing research have not kept pace with the latest developments in network architectures, such as peer-to-peer networks, sensor networks, ad-hoc wireless networks, and overlay networks. A common characteristic among all of these new technologies is the presence of highly dynamic network topologies. Currently deployed single-path routing protocols cannot adequately cope with this dynamism, and existing multi-path algorithms make trade-offs which lead to less than optimal performance on these networks. This drives the need for routing protocols designed with the un…
