The analysis of substances outside the cladding has challenged the optical fiber sensors community for decades. A common solution relies on the propagation of light in cladding modes. However, the coupling of light to/from these modes is typically based on permanent gratings in specific locations, which restrict the sensors to point measurements only. In this work, we present dynamic, random-access coupling of light between core and cladding modes of standard fibers, in arbitrarily located short sections. Coupling is based on the stimulation of Brillouin dynamic gratings by two coded pump waves and intermodal scattering of a third optical probe wave. All waves are launched and collected inthe core mode. No permanent gratings are inscribed. Distributed sensing of surrounding media is demonstrated with 2 m range and 8 cm resolution. Measurements distinguish between water and ethanol outside the fiber. The measurement accuracty of the local index outside the cladding is 0.004 - 0.0004 refractive index units.
We introduce a small-core air-guiding photonic crystal fiber whose cladding is made of improved air-silica photonic crystal with non-circular air holes placed in triangular lattice. The fiber achieves un-disturbed bandgap guidance over 350nm wavelength range.
Understanding cladding properties is crucial for designing microstructured optical fibers. This is particularly acute for Inhibited-Coupling guiding fibers because of the reliance of their core guidance on the core and cladding mode-field overlap integral. Consequently, careful planning of the fiber cladding parameters allows obtaining fibers with optimized characteristics such as low loss and broad transmission bandwidth. In this manuscript, we report on how one can tailor the modal properties of hollow-core photonic crystal fibers by adequately modifying the fiber cladding. We show that the …
A Core/Cladding Yb-doped fiber amplifier configuration is presented that relies on anti-Stokes fluorescence cooling for effective heat mitigation in high-power operation. In the proposed design, the inner cladding of the double clad fiber is doped with the same ion as in the core; therefore, the excess heat generated from the background absorption is removed by the anti-Stokes fluorescence in both core and inner cladding. We consider both silica and ZBLAN glasses for the host material in the Core/Cladding Yb-doped fiber amplifier. The model incorporates the spatial profiles of the signal and p…
The beam quality factor $M^2$ for the fundamental LP01 mode of a step-index fiber with a finite cladding diameter is calculated in the presence of gain, in a closed form, as a function of the complex generalized V-number. It is shown that the conventional infinite cladding diameter approximation cannot be used for index-antiguided gain-guided fibers, and the rigorous analysis presented in this paper is required for accurate prediction of the beam quality factor, as reported in recent experimental measurements.
In this paper we present a theoretical and numerical analysis of light localization in hollow core microstructured fibers (HCMFs) with a complicated shape of the core cladding boundary. The analysis is based on well established models (for example, the ARROW model) and also on the models proposed for the first time. In particular, we consider local and nonlocal mechanisms of light localization in the waveguide structures with a determined type of discrete rotational symmetry of the core cladding boundary. We interpret and analyze mechanisms of light localization in negative curvature hollow co…
Two highly birefringent polymer terahertz (THz) fibers were proposed in this paper, which were formed with honeycomb cladding and some elliptical air holes in the fiber core. The losses and mode birefringence for two different fibers are investigated by finite-different time-domain method. The results show that fiber 2 can achieve both high birefringence (larger than 0.022) and low confinement loss (0.01 dB/m) in a wide THz frequency range. Moreover, compared with a round solid-core fiber, guiding loss of the THz fiber caused by polymer material absorption can be reduced effectively as a part …
In this paper we consider an interaction between the air core modes of hollow core waveguide microstructures and core cladding boundary walls in various shapes. The analysis is based on well established models such as the anti-resonant reflecting optical waveguide model and on the models proposed for the first time. In particular, we consider the dynamics of light localization in the polygonalcore cladding boundary wall as dependant on the type of its discrete rotational symmetry. Based on our findings we analyze the mechanisms of light localization in the core cladding boundary walls of negat…
Here a detailed formalism to achieve an analytical solution of a lossy high power Yb-doped silica fiber laser is introduced. The solutions for the lossless fiber laser is initially attained in detail. Next, the solution for the lossy fiber laser is obtained based on the lossless fiber laser solution. To examine the solutions for both lossless and lossy fiber laser two sets of values are compared with the exact numerical solutions and the results are in a good agreement. Furthermore, steps and procedures for achieving the final solutions are explained clearly and precisely.
The spectral characteristics of a fiber Bragg grating (FBG) with a transversely inhomogeneous refractive index profile, differs con- siderably from that of a transversely uniform one. Transmission spectra of inhomogeneous and asymmetric FBGs that have been inscribed with focused ultrashort pulses with the so-called point-by-point technique are investigated. The cladding mode resonances of such FBGs can span a full octave in the spectrum and are very pronounced (deeper than 20dB). Using a coupled-mode approach, we compute the strength of resonant coupling and find that coupling into cladding mo…
We report on the writing of chirped volume Bragg gratings using 400 nm femtosecond pulses and the phase-mask inscription technique in the pure silica inner cladding of the gain fiber. The usefulness of such fiber component is demonstrated as a pump reflector in a cladding-pumped all-fiber laser. A reflectivity of 53% for the residual pump power guided in the cladding of the highly multimode 125 microns fiber is achieved, allowing for significant pump recycling in the fiber laser cavity which therefore optimizes the overall laser performances. As proof of concept, adding this pump reflector at …
Motivated by recent experimental work by Folkenberg et al. we consider the effect of weak disorder in the air-hole lattice of small-core photonic crystal fibers. We find that the broken symmetry leads to higher-order modes which have generic intensity distributions resembling those found in standard fibers with elliptical cores. This explains why recently reported experimental higher-order mode profiles appear very different from those calculated numerically for ideal photonic crystal fibers with inversion and six-fold rotational symmetry. The splitting of the four higher-order modes into two …
We consider an air-silica honeycomb lattice and demonstrate a new approach to the formation of a core defect. Typically, a high or low-index core is formed by adding a high-index region or an additional air-hole (or other low-index material) to the lattice, but here we discuss how a core defect can be formed by manipulating the cladding region rather than the core region itself. Germanium-doping of the honeycomb lattice has recently been suggested for the formation of a photonic band-gap guiding silica-core and here we experimentally demonstrate how an index-guiding silica-core can be formed b…
The temperature distribution inside a double-cladding optical fiber laser or amplifier is examined in detail. Traditionally, the quantum defect in the core is taken to be the main source of heating in an active optical fiber. However, contributions from the parasitic absorption of the signal and the pump may also play an important role, especially for low quantum defect or radiation-balanced lasers and amplifiers. The contributions to the heating in both the core and the inner-cladding are considered and analyzed in general terms in this paper. In particular, it is shown that if the maximum to…
Space-division multiplexing (SDM), whereby multiple spatial channels in multimode and multicore optical fibers are used to increase the total transmission capacity per fiber, is being investigated to avert a data capacity crunch and reduce the cost per transmitted bit. With the number of channels employed in SDM transmission experiments continuing to rise, there is a requirement for integrated SDM components that are scalable. Here, we demonstrate a cladding-pumped SDM erbium-doped fiber amplifier (EDFA) that consists of six uncoupled multimode erbium-doped cores. Each core supports three spat…
The advent of photonic bandgap (PBG) guiding hollow- core photonic crystal fiber (HC-PCF) sparked the hope of guiding light with attenuation below the fundamental silica Rayleigh scattering limit (SRSL) of conventional step-index fibers. Unfortunately, the combination of the strong core-cladding optical-overlap, the surface roughness at the silica cladding struts and the presence of interface-modes limited the lowest reported transmission-loss to 1.2 dB/km at 1550 nm. This hope is recently revived by the introduction of hypocycloid core- contour (i.e. negative curvature) in inhibited-coupling …
Understanding the impact of the cladding tube structure on the overall guiding performance is crucial for designing single-mode, wide-band, and ultra low-loss nested hollow-core anti-resonant fiber (HC-ARF). Here we thoroughly investigate on how the propagation loss is affected by the nested elements when their geometry is realistic (i.e., non-ideal). Interestingly, it was found that the size rather than the shape of the nested elements, have a dominant role in the final loss performance of the HC-ARFs. We identify a unique 'V-shape' pattern for suppression of higher-order modes loss by optimi…
Cladding structures of photonic band-gap fibers often have air-holes of non-circular shape and, typically, close-to-hexagonal air holes with curved corners are observed. We study photonic band-gaps in such structures by aid of a two-parameter representation of the size and curvature. For the fundamental band-gap we find that the band-gap edges (the intersections with the air line) shift toward shorter wavelengths when the air-filling fraction f is increased. The band-gap also broadens and the relative band-width increases exponentially with f^2. Comparing to recent experiments [Nature 424, 657…
By means of the transfer matrix method, the optical properties of fibers with a distinct intermediate layer between a hol-low core and periodic cladding are calculated. The periodic cladding consists of two types of the alternating layers. The intermediate layer has distinct thickness and refractive index. Depending on these parameters, the fiber can work in the single-mode or multi-mode regimes. In the multi-mode regime, the optical loss of the smallest loss mode can be de-creased by increasing the thickness of the layer. In the single-mode regime, the optical loss falls with a rise in the re…
A theoretical model for laser cooled continuous-wave fiber amplifier is presented. The amplification process takes place in the Tm3+-doped core of the fluoride ZBLAN (ZrF4-BaF2-LaF3-AlF3-NaF) glass fiber. The cooling process takes place in the Yb3+:ZBLAN fiber cladding. It is shown that for each value of the pump power and the amplified signal there is a distribution of the concentration of the Tm3+ along the length of the fiber amplifier, which provides its athermal operation. The influence of a small deviation in the value of the amplified signal on the temperature of the fiber with the fixe…
A novel plasmonic THz fiber is described that features two metallic wires that are held in place by the porous dielectric cladding functioning as a mechanical support. This design is more convenient for practical applications than a classic two metal wire THz waveguide as it allows direct manipulations of the fiber without the risk of perturbing its core-guided mode. Not surprisingly, optical properties of such fibers are inferior to those of a classic two-wire waveguide due to the presence of lossy dielectric near an inter-wire gap. At the same time, composite fibers outperform porous fibers …
In this work we report two designs of subwavelength fibers packaged for practical terahertz wave guiding. We describe fabrication, modeling and characterization of microstructured polymer fibers featuring a subwavelength-size core suspended in the middle of a large porous outer cladding. This design allows convenient handling of the subwavelength fibers without distorting their modal profile. Additionally, the air-tight porous cladding serves as a natural enclosure for the fiber core, thus avoiding the need for a bulky external enclosure for humidity-purged atmosphere. Fibers of 5 mm and 3 mm …
Optical fiber with high numerical aperture (NA) can efficiently relieve the degeneracy of higher order linearly polarized modes. The degeneracy relief is investigated in two types of high NA fibers, i.e., low index cladding fiber and high-index-core fiber. A naked core fiber, as with low index cladding, can be used theoretically to generate the orbital angular momentum mode (OAMM) HE21 and the cylindrically symmetric modes (CSMs) TM01 and TE01. A high index core fiber incorporated with high contrast index structure can be used similarly to obtain OAMM HE31. The generation of both CSMs and OAMM…
In this paper we propose a new hypothesis of out of plane band gap formation in all solid photonic band gap (PBG) fibers. At first, one considers the process of the core modes formation as a result of excitation of continuous mode spectrum of single dielectric rod of the cladding. It is shown that the core modes can be considered as transverse resonance of a set of the radiation modes decoupled from the continuum provided that the phase matching condition for the propagation constants are fulfilled. An analogy between the core mode formation in all solid PBG fibers and formation of bound state…
Wave chaos is a concept which has already proved its practical usefulness in design of double-clad fibers for cladding-pumped fiber lasers and fiber amplifiers. In general, classically chaotic geometries will favor strong pump absorption and we address the extent of chaotic wave dynamics in typical air-clad geometries. While air-clad structures supporting sup-wavelength convex air-glass interfaces (viewed from the high-index side) will promote chaotic dynamics we find guidance of regular whispering-gallery modes in air-clad structures resembling an overall cylindrical symmetry. Highly symmetri…
We analyse a multilayer leaky cladding (MLC) fibre using the finite element method and study the effect of the MLC on the bending loss and birefringence of two types of structures: (i) a circular core large-mode-area structure and (ii) an elliptical-small-core structure. In a large-mode-area structure, we verify that the multilayer leaky cladding strongly discriminates against higher order modes to achieve single-mode operation, the fibre shows negligible birefringence, and the bending loss of the fibre is low for bending radii larger than 10 cm. In the elliptical-small-core structure we show …
We demonstrate a quantitative broadband fiber sensor, based on evanescent field sensing in the cladding holes of an air-suspended solid-core photonic crystal fiber. We discuss the fabrication process, together with the structural- and optical characterization of a range of different fibers. Measured mode profiles are in good agreement with finite element method calculations made without free parameters. The fraction of the light in the hollow cladding can be tuned via the core diameter of the fiber. Dispersion measurements are in excellent agreement with theory and demonstrate tuning of the ze…
We study the class of endlessly single-mode all-silica photonic crystal fibers with a triangular air-hole cladding. We consider the sensibility to longitudinal nonuniformities and the consequences and limitations for realizing low-loss large-mode area photonic crystal fibers. We also discuss the dominating scattering mechanism and experimentally we confirm that both macro and micro-bending can be the limiting factor.
Optical fibers containing multiple cores are being developed towards capacity enhancement in space-division multiplexed optical communication networks. In many cases, the fibers are designed for negligible direct coupling of optical power among the cores. The cores remain, however, embedded in a single, mechanically-unified cladding. Elastic (or acoustic) modes supported by the fiber cladding geometry are in overlap with multiple cores. Acoustic waves may be stimulated by light in any core through electrostriction. Once excited, the acoustic waves may induce photo-elastic perturbations to opti…
We report on detailed in-situ distributed temperature measurements inside a high power fiber amplifier. The deducted thermal load and the TMI-threshold of a commercial LMA fiber with 25 micron core and 400 micron cladding was measured at various seed wavelengths. By matching these results with detailed simulations we show that photodarkening has a negligible impact on the thermal load and, therefore, on the TMI threshold in this fiber.
Leakage channel fibers, designed to suppress higher-order modes, demonstrate resonant power loss at certain critical radii of curvature. Outside the resonance, the power recovers to the levels offset by the usual mechanism of bend-induced loss. Using C$^2$-imaging, we experimentally characterize this anomaly and identify the corresponding physical mechanism as the radiative decay of the fundamental mode mediated by the resonant coupling to a cladding mode.
The remarkable recent demonstrations in ultralow loss Inhibited-Coupling (IC) hollow-core photonic crystal fibers (HCPCFs) place them as serious candidates for the next-generation of long-haul fiber optics systems. A hindrance to this prospect, but also to short-haul applications such as micromachining, where stable and high-quality beam delivery is needed, is the challenge to design and fabricate an IC-guiding fiber that combines ultra-low loss, truly and robust single-modeness, and polarization-maintaining operation. Design solutions proposed up to now require a trade-off between low loss an…
In recent years we are witnessing a flourish in research aimed to facilitate alkali vapors in guided wave configurations. Owing to the significant reduction in device dimensions, the increase in density of states, the interaction with surfaces and primarily the high intensities carried along the structure, a rich world of light vapor interactions can be studied, and new functionalities, e.g. low power nonlinear light-matter interactions can be achieved. One immense remaining challenge is to study the effects of quantum coherence and shifts in such nano-scale waveguides, characterized by ultra-…
We present detailed experimental study on noise-seeded intermodal modulation instability (IM-MI) in normal dispersion region of a conventional step-index fiber. The sharp refractive index contrast between core and cladding leads to large group velocity mismatch between the spatial modes, coaxing to efficient IM-MI and generation of multiple spectral peaks along with Raman peaks. Evolution of the spectrum with pump powers and fiber lengths are observed. Experimental findings are well supported with the theoretical framework based on bimodal-MI model considering the distinct dispersion parameter…
We propose a method for producing a conical beam based on the lateral refraction of the TM01 mode from a two-mode fiber after chemical etching of the cladding, and for controlling its radial polarization. The whole power of the guided mode is transferred to the refracted beam with low diffraction. Polarization control by a series of azimuthal detectors and a stress controller affords the transmission of a stabilized radial polarization through an optical fiber. A solid component usable for many applications has been obtained.
Hyperbolic Meta-Materials~(HMMs) are anisotropic materials with permittivity tensor that has both positive and negative eigenvalues. Here we report that by using a type II HMM as cladding material, a waveguide which only supports higher order modes can be achieved, while the lower order modes become leaky and are absorbed in the HMM cladding. This counter intuitive property can lead to novel application in optical communication and photonic integrated circuit. The loss in our HMM-Insulator-HMM~(HIH) waveguide is smaller than that of similar guided mode in a Metal-Insulator-Metal~(MIM) waveguid…
In this paper we present a label-free, stable and highly sensitive fiber-optic sensor for detection of environmental toxin microcystin-LR (MC-LR). Thiolated MC-LR-targeting aptamer covalently immobilized on dual-resonance long-period fiber gratings (DR-LPFG) is used as MC-LR recognition element and the spectral response of the DR-LPFG is monitored for various concentrations of MC-LR. Sensitivity of the DR-LPFG is optimized by coating an appropriate thickness of gold layer to the fiber surface. Gold coating serves two purposes, first it locally supports a surface-Plasmon mode associated with th…
We propose a Watt-level, all-fiber, ultrafast Er/Yb-codoped double-clad fiber laser passively mode-locked by reduced graphene oxide (rGO) interacting with a weak evanescent field of photonic crystal fiber (PCF). The rGO solution is filled into the cladding holes of the PCF based on total reflection, and after evaporation, the rGO flakes bear only 1/107 of the total energy in laser system, which enhances the thermal damage threshold and decreases the accumulated nonlinearity. By incorporating the saturable absorber into an Er/Yb-codoped fiber ring cavity, stable conventional soliton with a dura…
Surface modes (SM) are highly spatially localized modes existing at the core-cladding interface of photonic-bandgap hollow-core fiber (PBG-HCF). When coupling with SM, the air modes (AM) in the core would suffer a higher loss despite being spectrally within the cladding photonic bandgap, and would be highly dispersive around the avoided crossing (anti-crossing) wavelength. In this paper, we numerically demonstrate that such avoided crossings can play an important role in the tuning of the temperature dependence of group delay of AM of PBG-HCF. At higher temperatures, both the thermal-optic eff…
The optical properties of solid core microstructured optical fibers (SC MOFs) have been studied for a long time. The process of energy outflow of the core modes has always been associated with the process of constructive interference of the core modes fields under reflection from the photonic crystal cladding. In this paper, we want to offer a new look at the light localization in the core of SC MOFs related to the behavior of spin and orbital parts of the Poynting vector of these core modes and singularities arising in it.
The development of highly-sensitive and miniaturized sensors that capable of real-time analytes detection is highly desirable. Nowadays, toxic or colorless gas detection, air pollution monitoring, harmful chemical, pressure, strain, humidity, and temperature sensors based on photonic crystal fiber (PCF) are increasing rapidly due to its compact structure, fast response and efficient light controlling capabilities. The propagating light through the PCF can be controlled by varying the structural parameters and core-cladding materials, as a result, evanescent field can be enhanced significantly …
We study the dispersion and leakage properties for the recently reported low-loss photonic band-gap fiber by Smith et al. [Nature 424, 657 (2003)]. We find that surface modes have a significant impact on both the dispersion and leakage properties of the fundamental mode. Our dispersion results are in qualitative agreement with the dispersion profile reported recently by Ouzounov et al. [Science 301, 1702 (2003)] though our results suggest that the observed long-wavelength anomalous dispersion is due to an avoided crossing (with surface modes) rather than band-bending caused by the photonic ban…
The field energy distributions and effective mode areas of silica-based photonic bandgap fibers with a honeycomb airhole structure in the cladding and an extra airhole defining the core are investigated. We present a generalization of the common effective area definition, suitable for the problem at hand, and compare the results for the photonic bandgap fibers with those of index-guiding microstructured fibers. While the majority of the field energy in the honeycomb photonic bandgap fibers is found to reside in the silica, a substantial fraction (up to ~30%) can be located in the airholes. Thi…
Cylindrical vector beams (CVBs) have a wide range of applications owing to their particular polarization characteristics and optical field distributions. For the first time, an azimuthally polarized fiber laser without any polarization controller is proposed and demonstrated experimentally. The scheme is based on a self-designed ring-core fiber and transverse mode filter (TMF). The ring-core fiber can break the degeneracy of LP11 modes and make the TE01 mode propagate stably in the fiber laser. The TMF, which made from the ring-core fiber by depositing a layer of Aluminum on the cladding surfa…
We propose the use of a silicon-core optical fiber for terahertz (THz) waveguide applications. Finite-difference time-domain simulations have been performed based on a cylindrical waveguide with a silicon core and silica cladding. High-resistivity silicon has a flat dispersion over a 0.1 - 3 THz range, making it viable for propagation of tunable narrowband CW THz and possibly broadband picosecond pules of THz radiation. Simulations show the propagation dynamics and the integrated intensity, from which transverse mode profiles and absorption lengths are extraced. It is found that for 140 - 250 …
The analysis of surrounding media has been a long-standing challenge of optical fiber sensors. Measurements are difficult due to the confinement of light to the inner core of standard fibers. Over the last two years, new sensor concepts have enabled the analysis of liquids outside the cladding boundary, where light does not reach. Sensing is based on opto-mechanical, forward stimulated Brillouin scattering interactions between guided light and sound waves. In most previous works, however, the protective polymer coating of the fiber had to be removed first. In this work, we report the opto-mech…
The photonic crystal fibers (PCF) or air-silica microstructured fibers consist of a periodic array of dielectric transverse. By introducing a defect in this structure, it is possible to guide the light by a photonic bandgap effect, whose properties are different fundamentally from the guide by total internal reflection that takes place in conventional fibers. PCF with two cores have significant potential, and this is one of the main motivations witches led us to approach this theme in this article. Analysis of the inter-core coupling was also necessary to study the problem of crosstalk. Their …
We report on fabrication of depressed cladding optical waveguides buried in lithium niobate crystal with shaped femtosecond laser pulses. Depressed cladding waveguides of variable mode-field sizes are fabricated by forming the four sides of the cladding using a slit-beam shaping technique. We show that the waveguides fabricated by our technique allows single-mode propagation of the light polarized in both vertical and horizontal directions.
All-optical switching of 77 fs pulses centered at 1560 nm, driven by 270 fs, 1030 nm pulses in a dual-core optical fiber exhibiting high index contrast is presented. The fiber is made of a thermally matched pair of lead silicate and borosilicate glasses used as core and cladding material, respectively. The novel switching approach is based on nonlinear balancing of dual-core asymmetry, by control pulse intensity induced group velocity reduction of the fast fiber channel. Due to the fiber core made of soft glass with high nonlinearity high switching contrast exceeding 20 dB is attained under ap…
We report on the influence of core NA on thermal-induced mode instabilities (MI) in high power fiber amplifiers. Influence of core NA and V-parameter on MI has been investigated numerically. It shows that core NA has larger influence on MI for fibers with smaller core-cladding-ratio, and the influence of core NA on threshold is more obvious when the amplifiers are pumped at 915nm. The dependence of threshold on V-parameter revealed that the threshold increases linearly as V-parameter decreases when V-parameter is larger than 3.5, and the threshold shows exponentially increase as V-parameter de…
