In this paper, we propose a distributed power control algorithm for addressing the global energy efficiency (GEE) maximization problem subject to satisfying a minimum target SINR for all user equipments (UEs) in wireless cellular networks. We state the problem as a multi-objective optimization problem which targets minimizing total power consumption and maximizing total throughput, simultaneously, while a minimum target SINR is guaranteed for all UEs. We propose an iterative scheme executed in the UEs to control their transmit power using individual channel state information (CSI) such that the GEE is maximized in a distributed manner. We prove the convergence of the proposed iterative algorithm to its corresponding unique fixed point also shown by our numerical results. Additionally, simulation results demonstrate that our proposed scheme outperforms other algorithms in the literature and performs like the centralized algorithm executed in the base station and maximizes the GEE using the global CSI.
The integration of mobile edge computing (MEC) and wireless power transfer (WPT) technologies has recently emerged as an effective solution for extending battery life and increasing the computing power of wireless devices. In this paper, we study the resource allocation problem of a multi-user wireless powered MEC system, where the users share the wireless channel via direct sequence code division multiple access (DS-CDMA). In particular, we are interested in jointly optimizing the task offloading decisions and resource allocation, to maximize the weighted sum computation rate of all the users…
Wireless sensor network (WSN) consists of a group of dedicated sensors nodes which are distributed over a certain area for observing and recording the physical conditions (like temperature, sound, pressure) of the environment and organizing the collected data at a central location. These Sensor nodes are powered by a battery, so energy conservation becomes an important aspect in WSN. The Paper proposes a way of combining traditional LEACH (Low Energy Adaptive Clustering Hierarchy) with Mobile Sink and Rendezvous Nodes (RN Nodes) along with some changes in terms of cluster head selection proces…
The reconfigurable intelligent surface (RIS) has arose an upsurging research interest recently due to its promising outlook in 5G-and-beyond wireless networks. With the assistance of RIS, the wireless propagation environment is no longer static and could be customized to support diverse service requirements. In this paper, we will approach the rate maximization problems in RIS-aided wireless networks by considering the beamforming and reflecting design jointly. Three representative design problems from different system settings are investigated based on a proposed unified algorithmic framework…
The conventional outage in wireless communication systems is caused by the deterioration of the wireless communication link, i.e., the received signal power is less than the minimum received signal power. Is there a possibility that the outage occurs in wireless communication systems with a good channel state? Based on both communication and heat transfer theories, a power-consumption outage in the wireless communication between millimeter wave (mmWave) massive multiple-input multiple-output (MIMO) base stations (BSs) and smartphones has been modeled and analyzed. Moreover, the total transmiss…
Sparse code multiple access (SCMA) is the most concerning scheme among non-orthogonal multiple access (NOMA) technologies for 5G wireless communication new interface. Another efficient technique in 5G aimed to improve spectral efficiency for local communications is device-to-device (D2D) communications. Therefore, we utilize the SCMA cellular network coexisting with D2D communications for the connection demand of the Internet of things (IOT), and improve the system sum rate performance of the hybrid network. We first derive the information-theoretic expression of the capacity for all users and…
The fifth-generation (5G) wireless cellular system, which would be deployed by 2020, is expected to deliver significantly higher capacity and better network performance compared to those of the current fourth-generation (4G) system. Specifically, it is predicted that tens of billions of wireless devices will be connected to the wireless network over the next few years, which results in an exponential explosion of mobile data traffic. Therefore, more advanced wireless architecture, as well as radical and innovative access technologies, must be proposed to meet this urgent increasing growth of m…
Electronic health monitoring is one of the major applications of wireless body area networks (WBANs) that helps with early detection of any abnormal physiological symptoms. In this paper, we propose and solve an optimization problem that maximizes the energy efficiency (EE) of WBAN consisting of sensor nodes (SNs) equipped with energy harvesting capabilities communicating with an aggregator. We exploit the structure of the optimization problem to provide a sub-optimal solution at a lower computational complexity and derive the mathematical expressions of upper and lower bounds of the source ra…
By using wireless connectivity through cellular base stations (BSs), swarms of unmanned aerial vehicles (UAVs) can provide a plethora of services ranging from delivery of goods to surveillance. In particular, UAVs in a swarm can utilize wireless communications to collect information, like velocity and heading angle, from surrounding UAVs for coordinating their operations and maintaining target speed and intra-UAV distance. However, due to the uncertainty of the wireless channel, wireless communications among UAVs will experience a transmission delay which can impair the swarm's ability to stab…
Cellular-connected wireless connectivity provides new opportunities for virtual reality(VR) to offer seamless user experience from anywhere at anytime. To realize this vision, the quality-of-service (QoS) for wireless VR needs to be carefully defined to reflect human perception requirements. In this paper, we first identify the primary drivers of VR systems, in terms of applications and use cases. We then map the human perception requirements to corresponding QoS requirements for four phases of VR technology development. To shed light on how to provide short/long-range mobility for VR services…
Virtual reality (VR) enables mobile wireless users to experience multimodal perceptions in a virtual space. In this paper we investigate the problem of concurrent support of visual and haptic perceptions over wireless cellular networks, with a focus on the downlink transmission phase. While the visual perception requires moderate reliability and maximized rate, the haptic perception requires fixed rate and high reliability. Hence, the visuo-haptic VR traffic necessitates the use of two different network slices: enhanced mobile broadband (eMBB) for visual perception and ultra-reliable and low l…
Mobile edge computing (MEC) and wireless power transfer (WPT) are two promising techniques to enhance the computation capability and to prolong the operational time of low-power wireless devices that are ubiquitous in Internet of Things. However, the computation performance and the harvested energy are significantly impacted by the severe propagation loss. In order to address this issue, an unmanned aerial vehicle (UAV)-enabled MEC wireless powered system is studied in this paper. The computation rate maximization problems in a UAV-enabled MEC wireless powered system are investigated under bot…
Weighted-sum energy efficiency (WSEE) is a key performance metric in heterogeneous networks, where the nodes may have different energy efficiency (EE) requirements. Nevertheless, WSEE maximization is a challenging problem due to its nonconvex sum-of-ratios form. Unlike previous work, this paper presents a systematic approach to WSEE maximization under not only power constraints, but also data rate constraints, using a general SINR expression. In particular, the original problem is transformed into an equivalent form, and then a sequential convex optimization (SCO) algorithm is proposed. This a…
In this paper, we study an energy efficiency maximization problem in uplink for D2D communications underlaid with cellular networks on multiple bands. Utilizing stochastic geometry, we derive closed-form expressions for the average sum rate, successful transmission probability, and energy efficiency of cellular and D2D users. Then, we formulate an optimization problem to jointly maximize the energy efficiency of D2D and cellular users and obtain optimum transmission power of both D2D and cellular users. In the optimization problem, we guarantee the QoS of users by taking into account the succe…
In this paper, we consider a full duplex wireless powered communication network where multiple users with RF energy harvesting capabilities communicate to a hybrid energy and information access point. An optimization framework is proposed with the objective of maximizing the sum throughput of the users subject to energy causality and maximum transmit power constraints considering a realistic energy harvesting model incorporating initial battery levels of the users. The joint optimization of power control, time allocation and scheduling is mathematically formulated as a mixed integer non linear…
The technology of Reconfigurable Intelligent Surfaces (RISs) has lately attracted considerable interest from both academia and industry as a low-cost solution for coverage extension and signal propagation control. In this paper, we study the downlink of a multi-cell wideband communication system comprising single-antenna Base Stations (BSs) and their associated single-antenna users, as well as multiple passive RISs. We assume that each BS controls a separate RIS and performs Orthogonal Frequency Division Multiplexing (OFDM) transmissions. Differently from various previous works where the RIS u…
This paper investigates full-duplex unmanned aerial vehicle (UAV) aided small cell wireless systems, where the UAV serving as the base station (BS) is designed to transmit data to the downlink users and receive data from the uplink users simultaneously. To maximize the total system capacity, including uplink and downlink capacity, the UAV trajectory, downlink/uplink user scheduling, and uplink user transmit power are alternately optimized. The resulting optimization problem is mixed-integer and non-convex, which is challenging to solve. To address it, the block coordinate descent method and su…
Reconfigurable intelligent surfaces (RIS) is a promising solution to build a programmable wireless environment via steering the incident signal in fully customizable ways with reconfigurable passive elements. In this paper, we consider a RIS-aided multiuser multiple-input single-output (MISO) downlink communication system. Our objective is to maximize the weighted sum-rate (WSR) of all users by joint designing the beamforming at the access point (AP) and the phase vector of the RIS elements, while both the perfect channel state information (CSI) setup and the imperfect CSI setup are investigat…
This paper studies an unmanned aerial vehicle (UAV)-enabled two-user interference channel for wireless powered communication networks (WPCNs), in which two UAVs wirelessly charge two low-power Internet-of-things (IoT)-devices on the ground and collect information from them. We consider two scenarios when both UAVs cooperate in energy transmission and/or information reception via interference coordination and coordinated multi-point (CoMP), respectively. For both scenarios, the UAVs' controllable mobility is exploited via trajectory design to not only enhance the wireless power transfer (WPT) e…
University of Colorado（科罗拉多大学）；Virginia Tech（弗吉尼亚理工学院）
Collaborative deep reinforcement learning (CDRL) algorithms in which multiple agents can coordinate over a wireless network is a promising approach to enable future intelligent and autonomous systems that rely on real-time decision-making in complex dynamic environments. Nonetheless, in practical scenarios, CDRL faces many challenges due to the heterogeneity of agents and their learning tasks, different environments, time constraints of the learning, and resource limitations of wireless networks. To address these challenges, in this paper, a novel semantic-aware CDRL method is proposed to enab…
In this paper, we address the problem of three dimensional beamforming in millimeter wave (mmWave) wireless networks. In particular, we study the impact of base station (BS) antenna tilt angle optimization on the energy efficiency (EE) of mmWave networks under two different scenarios: a homogeneous network consisting of multiple macro base stations (MBSs), and a heterogeneous network where several femto base stations are added within the coverage areas of the MBSs. First, by adopting a stochastic geometry approach, we analyze the coverage probability of both scenarios that incorporate 3DBF. Th…
Traditional seismic acquisition systems suffer from a number of difficulties related to telemetry cables that are used as a means of data transmission. Transforming the traditional seismic acquisition system to a wireless system has been considered as a potential solution to most of these difficulties. The wireless seismic acquisition system has to serve a huge aggregate data rate requirement as is usually the case in a large wireless sensor network. This paper considers the wireless acquisition system, and studies the maximum achievable transmission data rates from the geophones to the wirele…
Integrated access and backhaul (IAB) networks have the potential to provide high data rate in both access and backhaul networks by sharing the same spectrum. Due to the dense deployment of small base stations (SBSs), IAB networks connect SBSs to the core network in a wireless manner without the deployment of high-cost optical fiber. As large spectrum is available in mmWave bands and high data rate is achieved by using directional beamforming, the access and backhaul links can be integrated in the same frequency band while satisfying quality-of-service constraints. In this work, we optimize the…
Wireless network virtualization is emerging as an important technology for next-generation (5G) wireless networks. A key advantage of introducing virtualization in cellular networks is that service providers can robustly share virtualized network resources (e.g., infrastructure and spectrum) to extend coverage, increase capacity, and reduce costs. {However, the inherent features of wireless networks, i.e., the uncertainty in user equipment (UE) locations and channel conditions impose significant challenges on virtualization and sharing of the network resources.} In this context, we propose a s…
The high reflect beamforming gain of the intelligent reflecting surface (IRS) makes it appealing not only for wireless information transmission but also for wireless power transfer. In this letter, we consider an IRS-assisted wireless powered communication network, where a base station (BS) transmits energy to multiple users grouped into multiple clusters in the downlink, and the clustered users transmit information to the BS in the manner of hybrid non-orthogonal multiple access and time division multiple access in the uplink. We investigate optimizing the reflect beamforming of the IRS and t…
We consider an intelligent reflecting surface (IRS)-assisted wireless powered communication network (WPCN) in which a multi antenna power beacon (PB) sends a dedicated energy signal to a wireless powered source. The source first harvests energy and then utilizing this harvested energy, it sends an information signal to destination where an external interference may also be present. For the considered system model, we formulated an analytical problem in which the objective is to maximize the throughput by jointly optimizing the energy harvesting (EH) time and IRS phase shift matrices. The optim…
The integration of renewable energy sources (RES) has facilitated efficient and sustainable resource allocation for wireless communication systems. In this paper, a novel framework is introduced to develop coordinated multicell beamforming (CMBF) design for wireless cellular networks powered by a smart microgrid, where the BSs are equipped with RES harvesting devices and can perform two-way (i.e., buying/selling) energy trading with the main grid. To this end, new models are put forth to account for the stochastic RES harvesting, two-way energy trading, and conditional value-at-risk (CVaR) bas…
This paper considers an active intelligent reflecting surface (IRS)-aided wireless powered communication network (WPCN), where devices first harvest energy and then transmit information to a hybrid access point (HAP). Different from the existing works on passive IRS-aided WPCNs, this is the first work that introduces the active IRS in WPCNs. To guarantee fairness, the problem is formulated as an amplifying power-limited weighted sum throughput (WST) maximization problem, which is solved by successive convex approximation technique and fractional programming alternatively. To balance the perfor…
Energy-efficient computation is an inevitable trend for mobile edge computing (MEC) networks. Resource allocation strategies for maximizing the computation efficiency are critically important. In this paper, computation efficiency maximization problems are formulated in wireless-powered MEC networks under both partial and binary computation offloading modes. A practical non-linear energy harvesting model is considered. Both time division multiple access (TDMA) and non-orthogonal multiple access (NOMA) are considered and evaluated for offloading. The energy harvesting time, the local computing …
In this paper, we introduce a backscatter assisted wirelessly powered mobile edge computing (MEC) network, where each edge user (EU) can offload task bits to the MEC server via hybrid harvest-then-transmit (HTT) and backscatter communications. In particular, considering a practical non-linear energy harvesting (EH) model and a partial offloading scheme at each EU, we propose a scheme to maximize the weighted sum computation bits of all the EUs by jointly optimizing the backscatter reflection coefficient and time, active transmission power and time, local computing frequency and execution time …
Simultaneous wireless information and power transfer (SWIPT) and intelligent reflecting surface (IRS) are two promising techniques for providing enhanced wireless communication capability and sustainable energy supply to energy-constrained wireless devices. Moreover, the combination of the IRS and the SWIPT can create the "one plus one greater than two" effect. However, due to the broadcast nature of wireless media, the IRS-aided SWIPT systems are vulnerable to eavesdropping. In this paper, we study the security issue of the IRS-aided SWIPT systems. The objective is to maximize the secrecy rat…
Optical wireless communication provides data transmission at high speeds which can satisfy the increasing demands for connecting a massive number of devices to the Internet. In this paper, vertical-cavity surface-emitting(VCSEL) lasers are used as transmitters due to their high modulation speed and energy efficiency. However, a high number of VCSEL lasers is required to ensure coverage where each laser source illuminates a confined area. Therefore, multiple users are classified into different sets according to their connectivity. Given this point, a transmission scheme that uses blind interfer…
In this paper we consider the uplink of a massive MIMO communication system using 5G New Radio-compliant multiple access, which is to co-exist with a radar system using the same frequency band. We propose a system model taking into account the reverberation (clutter) produced by the radar system at the massive MIMO receiver. Then, we propose several linear receivers for uplink data-detection, ranging by the simple channel-matched beamformer to the zero-forcing and linear minimum mean square error receivers for clutter disturbance rejection. Our results show that the clutter may have a strong e…
Antenna Elements' Trajectory Optimization for Throughput Maximization in Continuous-Trajectory Fluid Antenna-Aided Wireless Communications
National Key Laboratory of Wireless Communications, University of Electronic Science and Technology of China（电子科技大学无线通信国家重点实验室）；School of Electrical and Electronic Engineering, Nanyang Technological University（南洋理工大学电气与电子工程学院）；Department of Electronic and Electrical Engineering, University College London（伦敦大学学院电子与电气工程系）；Department of Electronic Engineering, Kyung Hee University（庆熙大学电子工程系）；Department of Electronics and Information Convergence Engineering, Kyung Hee University（庆熙大学电子与信息融合工程系）
Up until now, path planning for unmanned aerial vehicles (UAVs) has mainly been focused on the optimisation towards energy efficiency. However, to operate UAVs safely, wireless coverage is of utmost importance. Currently, deployed cellular networks often exhibit an inadequate performance for aerial users due to high amounts of intercell interference. Furthermore, taking the never-ending trend of densification into account, the level of interference experienced by UAVs will only increase in the future. For the purpose of UAV trajectory planning, wireless coverage should be taken into account to…
The research efforts on cellular vehicle-to-everything (V2X) communications are gaining momentum with each passing year. It is considered as a paradigm-altering approach to connect a large number of vehicles with minimal cost of deployment and maintenance. This article aims to further push the state-of-the-art of cellular V2X communications by providing an optimization framework for wireless charging, power allocation, and resource block assignment. Specifically, we design a network model where roadside objects use wireless power from RF signals of electric vehicles for charging and informatio…
In this paper, we consider a full duplex wireless powered communication network where multiple users with radio frequency energy harvesting capability communicate to an energy broadcasting hybrid access point. We investigate the minimum length scheduling and sum throughput maximization problems considering on-off transmission scheme in which users either transmit at a constant power or remain silent. For minimum length scheduling problem, we propose a polynomial-time optimal scheduling algorithm. For sum throughput maximization, we first derive the characteristics of an optimal schedule and th…
In this paper, we propose an active reconfigurable intelligent surface (RIS) enabled hybrid relaying scheme for a multi-antenna wireless powered communication network (WPCN), where the active RIS is employed to assist both wireless energy transfer (WET) from the power station (PS) to energy-constrained users and wireless information transmission (WIT) from users to the receiving station (RS). For further performance enhancement, we propose to employ both transmit beamforming at the PS and receive beamforming at the RS. We formulate a sum-rate maximization problem by jointly optimizing the RIS …
