The strict latency and reliability requirements of ultra-reliable low-latency communications (URLLC) use cases are among the main drivers in fifth generation (5G) network design. Link adaptation (LA) is considered to be one of the bottlenecks to realize URLLC. In this paper, we focus on predicting the signal to interference plus noise ratio at the user to enhance the LA. Motivated by the fact that most of the URLLC use cases with most extreme latency and reliability requirements are characterized by semi-deterministic traffic, we propose to exploit the time correlation of the interference to compute useful statistics needed to predict the interference power in the next transmission. This prediction is exploited in the LA context to maximize the spectral efficiency while guaranteeing reliability at an arbitrary level. Numerical results are compared with state of the art interference prediction techniques for LA. We show that exploiting time correlation of the interference is an important enabler of URLLC.
Ensuring ultra-reliable and low-latency communication (URLLC) for 5G wireless networks and beyond is of capital importance and is currently receiving tremendous attention in academia and industry. At its core, URLLC mandates a departure from expected utility-based network design approaches, in which relying on average quantities (e.g., average throughput, average delay and average response time) is no longer an option but a necessity. Instead, a principled and scalable framework which takes into account delay, reliability, packet size, network architecture, and topology (across access, edge, a…
Ultra-reliable low-latency communications (URLLC) has been considered as one of the three new application scenarios in the \emph{5th Generation} (5G) \emph {New Radio} (NR), where the physical layer design aspects have been specified. With the 5G NR, we can guarantee the reliability and latency in radio access networks. However, for communication scenarios where the transmission involves both radio access and wide area core networks, the delay in radio access networks only contributes to part of the \emph{end-to-end} (E2E) delay. In this paper, we outline the delay components and packet loss p…
This work considers the multihop multiple-input multiple-output relay network under short-packet communications to facilitate not only ultra-reliability but also low-latency communications. We assume that the transmit antenna selection (TAS) scheme is utilized at the transmit side, whereas either selection combining (SC) or maximum ratio combining (MRC) is leveraged at the receive side to achieve diversity gains. For quasi-static Rayleigh fading channels and the finite-blocklength regime, we derive the approximate closed-form expressions of the end-to-end (e2e) block error rate (BLER) for both…
The rapid development of the fifth generation mobile communication systems accelerates the implementation of vehicle-to-everything communications. Compared with the other types of vehicular communications, vehicle-to-vehicle (V2V) communications mainly focus on the exchange of driving safety information with neighboring vehicles, which requires ultra-reliable and low-latency communications (URLLCs). However, the frame size is significantly shortened in V2V URLLCs because of the rigorous latency requirements, and thus the overhead is no longer negligible compared with the payload information fr…
The Internet of Things (IoT) enables smart cities to achieve the vision of connecting everything by smartly linking gadgets without the need for human interaction. However, due to the rapid proliferation of IoT devices, the amount of data produced accounts for a significant share of all communication services. Hence, 6G-enabled specifications for wireless networks are required to enable both massive and ultra-reliable low-latency access to such a hybrid IoT network. In this article, we propose a smart hybrid random access (SH-RA) scheme for massive connections and ultra-reliable low-latency ac…
To efficiently support the real-time control applications, networked control systems operating with ultra-reliable and low-latency communications (URLLCs) become fundamental technology for future Internet of things (IoT). However, the design of control, sensing and communications is generally isolated at present. In this paper, we propose the joint optimization of control cost and energy consumption for a centralized wireless networked control system. Specifically, with the ``sensing-then-control'' protocol, we first develop an optimization framework which jointly takes control, sensing and co…
Online Learning of Modular Bayesian Deep Receivers: Single-Step Adaptation with Streaming Data
School of ECE, Ben-Gurion University of the Negev（内盖夫本-古里安大学电气与计算机工程学院）；Institute for Intelligent Networked Systems, Northeastern University London（伦敦东北大学智能网络系统研究所）
The fifth generation (5G) mobile technology features the ultra-reliable and low-latency communications (URLLC) as a major service class. URLLC applications demand a tight radio latency with extreme link reliability. In 5G dynamic time division duplexing (TDD) systems, URLLC requirements become further challenging to achieve due to the severe and fast-varying cross link interference (CLI) and the switching time of the radio frame configurations (RFCs). In this work, we propose a quasi-dynamic inter-cell frame coordination algorithm using hybrid frame design and a cyclic-offset-based RFC code-bo…
This paper presents novel ultrareliable and low-latency communication (URLLC) techniques for URLLC services, such as Tactile Internet services. Among typical use-cases of URLLC services are tele-operation, immersive virtual reality, cooperative automated driving, and so on. In such URLLC services, new kinds of traffic such as haptic information including kinesthetic information and tactile information need to be delivered in addition to high-quality video and audio traffic in traditional multimedia services. Further, such a variety of traffic has various characteristics in terms of packet size…
For the fifth generation (5G) wireless network technology, the most important design goals were improved metrics of reliability and latency, in addition to network resilience and flexibility so as to best adapt the network operation for new applications such as augmented virtual reality, industrial automation and autonomous vehicles. That led to design efforts conducted under the subject of ultra-reliable low-latency communication (URLLC). The technologies integrated in Release 15 of the 3rd Generation Partnership Project (3GPP) finalized in December 2017 provided the foundation of physical la…
The next generation ultra-reliable and low-latency communications (xURLLC) need novel design to provide satisfactory services to the emerging mission-critical applications. To improve the spectrum efficiency and enhance the robustness of xURLLC, this paper proposes a robust beamforming and rate-splitting design in the finite blocklength (FBL) regime for downlink multi-user multi-antenna xURLLC systems. In the design, adaptive rate-splitting is introduced to flexibly handle the complex inter-user interference and thus improve the spectrum efficiency. Taking the imperfection of the channel state…
This paper presents a new class of sparse superposition codes for low-rates and short-packet communications over the additive white Gaussian noise channel. The new code is orthogonal sparse superposition (OSS) code. A codeword of OSS codes is represented as a superposition of sparse sub-codewords whose support sets are mutually non-overlapping. To construct such codewords in a computationally efficient manner, a successive encoding method is presented. Harnessing the orthogonal property among sub-codewords, a simple yet near-optimal decoding method is proposed, which performs element-wise maxi…
The ultra-reliable and low-latency communication (URLLC) is the key driver of the current 5G new radio standardization. URLLC encompasses sporadic and small-payload transmissions that should be delivered within extremely tight radio latency and reliability bounds, i.e., a radio latency of 1 ms with 99.999% success probability. However, such URLLC targets are further challenging in the 5G dynamic time division duplexing (TDD) systems, due to the switching between the uplink and downlink transmission opportunities and the additional inter-cell cross-link interference (CLI). This paper presents a…
Current radio systems are currently optimized for capacity and range. However, certain applications of wireless systems require fast and reliable communication over short distances. The challenge of these systems is to communicate with a minimum time delay (latency) while at the same time being very reliable and resilient to interference. This paper describes the concept and the proposed abstract architecture of a wireless technology that allows highly reliable and ultra low latency transmission of data between moving units over a few meters, the applications of which can be found in multitude…
In this paper, we study how to solve resource allocation problems in ultra-reliable and low-latency communications by unsupervised deep learning, which often yield functional optimization problems with quality-of-service (QoS) constraints. We take a joint power and bandwidth allocation problem as an example, which minimizes the total bandwidth required to guarantee the QoS of each user in terms of the delay bound and overall packet loss probability. The global optimal solution is found in a symmetric scenario. A neural network was introduced to find an approximated optimal solution in general …
Major goal of ultra reliable and low latency communication (URLLC) is to reduce the latency down to a millisecond (ms) level while ensuring reliability of the transmission. Since the current uplink transmission scheme requires a complicated handshaking procedure to initiate the transmission, to meet this stringent latency requirement is a challenge in wireless system design. In particular, in the time division duplexing (TDD) systems, supporting the URLLC is difficult since the mobile device has to wait until the transmit direction is switched to the uplink. In this paper, we propose a new app…
University of Sydney（悉尼大学）；Beihang University（北京航空航天大学）；Princeton University（普林斯顿大学）
As one of the key communication scenarios in the 5th and also the 6th generation (6G) of mobile communication networks, ultra-reliable and low-latency communications (URLLC) will be central for the development of various emerging mission-critical applications. State-of-the-art mobile communication systems do not fulfill the end-to-end delay and overall reliability requirements of URLLC. In particular, a holistic framework that takes into account latency, reliability, availability, scalability, and decision making under uncertainty is lacking. Driven by recent breakthroughs in deep neural netwo…
The fifth generation (5G) of wireless systems holds the promise of supporting a wide range of services with different communication requirements. Ultra-reliable low-latency communications (URLLC) is a generic service that enables mission-critical applications, such as industrial automation, augmented reality, and vehicular communications. URLLC has stringent requirements for reliability and latency of delivering both data and control information. In order to meet these requirements, the Third Generation Partnership Project (3GPP) has been introducing new features to the upcoming releases of th…
The integration of Visible-Light Communications technology (VLC) in Intelligent Transportation Systems (ITS) is a very promising platform for a cost-effective implementation of revolutionary ITS and cooperative ITS protocols. In this paper, we propose an infrastructure-to-vehicle-to-vehicle (I2V2V) VLC system for ITS, implementing it through a regular LED traffic light serving as a transmitter and a digital Active Decode-and-Relay (ADR) stage for decoding and relaying the received information towards further incoming units. The proposed VLC system targets the challenging and important case of …
Future mobile networks not only envision enhancing the traditional link quality and data rates of mobile broad band (MBB) links, but also development of new control channels to meet the requirements of delay sensitive use cases. In particular, the need for ultra-reliable low-latency communications (URLLC) for many internet of things (IoT) users is greatly emphasized. In this paper, we present a novel spread spectrum waveform design that we propose for transmission of control signals to establish URLLC communications. These control signals are transmitted over the spectral resources that belong…
With the rapid deployment of the Internet of Things (IoT), fifth-generation (5G) and beyond 5G networks are required to support massive access of a huge number of devices over limited radio spectrum radio. In wireless networks, different devices have various quality-of-service (QoS) requirements, ranging from ultra-reliable low latency communications (URLLC) to high transmission data rates. In this context, we present a joint energy-efficient subchannel assignment and power control approach to manage massive access requests while maximizing network energy efficiency (EE) and guaranteeing diffe…
To date, model-based reliable communication with low latency is of paramount importance for time-critical wireless control systems. In this work, we study the downlink (DL) controller-to-actuator scheduling problem in a wireless industrial network such that the outage probability is minimized. In contrast to the existing literature based on well-known stationary fading channel models, we assume an arbitrary and unknown channel fading model, which is available only via samples. To overcome the issue of limited data samples, we invoke the generative adversarial network framework and propose an o…
School of Electrical and Information Engineering, the University of Sydney（悉尼大学电气与信息工程学院）；School of Electronics and Information Engineering, Beihang University（北京航空航天大学电子信息工程学院）；School of Electrical Engineering and Computer Science, Peking University（北京大学电子工程与计算机科学学院）
In the future 6th generation networks, ultra-reliable and low-latency communications (URLLC) will lay the foundation for emerging mission-critical applications that have stringent requirements on end-to-end delay and reliability. Existing works on URLLC are mainly based on theoretical models and assumptions. The model-based solutions provide useful insights, but cannot be directly implemented in practice. In this article, we first summarize how to apply data-driven supervised deep learning and deep reinforcement learning in URLLC, and discuss some open problems of these methods. To address the…
In this paper, the problems of user offloading and resource optimization are jointly addressed to support ultra-reliable and low latency communications (URLLC) in HetNets. In particular, a multi-tier network with a single macro base station (MBS) and multiple overlaid small cell base stations (SBSs) is considered that includes users with different latency and reliability constraints. Modeling the latency and reliability constraints of users with probabilistic guarantees, the joint problem of user offloading and resource allocation (JUR) in a URLLC setting is formulated as an optimization probl…
While the notion of age of information (AoI) has recently been proposed for analyzing ultra-reliable low-latency communications (URLLC), most of the existing works have focused on the average AoI measure. Designing a wireless network based on average AoI will fail to characterize the performance of URLLC systems, as it cannot account for extreme AoI events, occurring with very low probabilities. In contrast, this paper goes beyond the average AoI to improve URLLC in a vehicular communication network by characterizing and controlling the AoI tail distribution. In particular, the transmission po…
University of Piraeus（比雷埃夫斯大学）；RapidMiner GmbH（RapidMiner有限公司）；Nokia Standardization Department（诺基亚标准化部）；Université Paris-Saclay（巴黎萨克雷大学）；CNRS（法国国家科学研究中心）；CentraleSupélec（巴黎中央理工-高等电力学院）
Terahertz (THz) wireless networks are expected to catalyze the beyond fifth generation (B5G) era. However, due to the directional nature and the line-of-sight demand of THz links, as well as the ultra-dense deployment of THz networks, a number of challenges that the medium access control (MAC) layer needs to face are created. In more detail, the need of rethinking user association and resource allocation strategies by incorporating artificial intelligence (AI) capable of providing "real-time" solutions in complex and frequently changing environments becomes evident. Moreover, to satisfy the ul…
The University of Sydney（悉尼大学）；Huazhong University of Science and Technology（华中科技大学）；Harbin Institute of Technology (Shenzhen)（哈尔滨工业大学（深圳））
In this paper, we aim to improve the Quality-of-Service (QoS) of Ultra-Reliability and Low-Latency Communications (URLLC) in interference-limited wireless networks. To obtain time diversity within the channel coherence time, we first put forward a random repetition scheme that randomizes the interference power. Then, we optimize the number of reserved slots and the number of repetitions for each packet to minimize the QoS violation probability, defined as the percentage of users that cannot achieve URLLC. We build a cascaded Random Edge Graph Neural Network (REGNN) to represent the repetition …
Edge Computing in 5G and Beyond is a promising solution for ultra-low latency applications (e.g. Autonomous Vehicle, Augmented Reality, and Remote Surgery), which have an extraordinarily low tolerance for the delay and require fast data processing for a very high volume of data. The requirements of delay-sensitive applications (e.g. Low latency, proximity, and Location/Context-awareness) cannot be satisfied by Cloud Computing due to the high latency between User Equipment and Cloud. Nevertheless, Edge Computing in 5G and beyond can promise an ultra-high-speed caused by placing computation capa…
