Approaching the limits of optoelectronic performance in mixed cation mixed halide perovskites by controlling surface recombination
Sarthak Jariwala, Sven Burke, Sean Dunfield, Clayton Shallcross, Margherita Taddei, Jian Wang, Giles E. Eperon, Neal R. Armstrong, Joseph J. Berry, David S. Ginger
We demonstrate the critical role of surface recombination in mixed-cation, mixed-halide perovskite, FA0.83Cs0.17Pb(I0.85Br0.15)3. By passivating non-radiative defects with the polymerizable Lewis base (3-aminopropyl)trimethoxysilane (APTMS) we transform these thin films. We demonstrate average minority carrier lifetimes > 4 μs, nearly single exponential monomolecular PL decays, and concomitantly high external photoluminescence quantum efficiencies (>20%, corresponding to ~97% of the maximum theoretical quasi-Fermi-level splitting) at low excitation fluence. We confirm both the composition and valence band edge position of the FA0.83Cs0.17Pb(I0.85Br0.15)3 perovskite using multi-institution, cross-validated, XPS and UPS measurements. We extend the APTMS surface passivation to higher bandgap double cation (FA,Cs) compositions (1.7 eV, 1.75 eV and 1.8 eV) as well as the widely used triple cation (FA,MA,Cs) composition and observe significant PL and PL lifetime improvements after surface passivation. Finally, we demonstrate that the average surface recombination velocity (SRV) decreases from ~1000 cm/s to ~10 cm/s post APTMS passivation for FA0.83Cs0.17Pb(I0.85Br0.15)3. Our results demonstrate that surface-mediated recombination is the primary non-radiative loss pathway in MA-free mixed-cation mixed-halide films with a range of different bandgaps, which is a problem observed for a wide range of perovskite active layers and reactive electrical contacts. This study indicates that surface passivation and contact engineering will enable near-theoretical device efficiencies with these materials.
Previous theoretical calculations show azetidinium has the right radial size to form a 3D perovskite with lead halides [1], and has been shown to impart, as the A-site cation of ABX3 unit, beneficial properties to ferroelectric perovskites [2]. However, there has been very limited research into its use as the cation in lead halide perovskites to date. In this communication we report the synthesis and characterization of azetidinium-based lead mixed halide perovskite colloidal nanocrystals. The mixed halide system is iodine and chlorine unlike other reported nanocrystals in the literature where…
Halide perovskites are promising materials for light-emitting and light-harvesting applications. In this context, two-dimensional perovskites such as nanoplatelets or Ruddlesden-Popper and Dion-Jacobson layered structures are important because of their structural flexibility, electronic confinement, and better stability. This review article brings forth an extensive overview of the recent developments of two-dimensional halide perovskites both in the colloidal and non-colloidal forms. We outline the strategy to synthesize and control the shape and discuss different crystalline phases and optoe…
Hybrid lead halide perovskites with 2D stacking structures have recently emerged as promising materials for optoelectronic applications. We report a method for growing 2D nanosheets of hybrid lead halide perovskites (I, Br and Cl), with tunable lateral sizes ranging from 0.05 to 8 microns, and a structure consisting of n stacked monolayers separated by long alkylamines, tunable from bulk down to n=1. The key to obtaining such a wide range of perovskite properties hinged on utilizing the respective lead halide nanosheets as precursors in a hot-injection synthesis that afforded careful control o…
Ionic migration in organo-halide perovskites plays an important role in operation of perovskite based solar cells and light emitting diodes. Despite the ionic migration being a reversible process, it often leads to worsening of perovskite based device performance, hysteresis in current-voltage characteristics, and phase segregation in mixed halide perovskites being as the most harmful effect. The reason is in dynamical band structure changes, which controllable engineering would solve one of the biggest challenges for development of light-emitting solar cells. Here we demonstrate controllable …
Mixed-cation Cesium-Methylammonium lead halide perovskite (CsxMA1-xPbI3-xBrx) thin-films have been used to demonstrate stable and efficient perovskite devices. However, a systematic study of the Cs incorporation on the properties of the perovskite films has not been reported. In this report, Impact of Cesium incorporation on the minority carrier recombination lifetime of Cesium-Methylammonium lead halide perovskite thin-films is studied. The lifetime for the as-deposited perovskite films decreases with increasing concentration of cesium. However, mixed cation perovskite film is more stable, sh…
Light emission and detection are the two fundamental attributes of optoelectronic communication systems. Until now, both functions have been demonstrated using the p-n diode which is exploited across a wide range of applications. However, due to the competing dynamics of carrier injection and photocarrier collection, with this device light emission and detection are realized separately by switching the direction of the applied electrical bias. Here we use mobile ions in halide perovskites to demonstrate light-emitting photodetection in either condition of applied electrical bias. Our device co…
One of the most significant features of lead-halide perovskites are their ability to have comparably slow recombination despite the fact that these materials are mostly processed from solution at room temperature. The slow recombination allows achieving high open-circuit voltages when the lead-halide perovskite layers are used in solar cells. This perspective discusses the state of the art of our understanding and of experimental data with regard to recombination and open-circuit voltages in lead-halide perovskites. A special focus is put onto open questions that the community has to tackle to…
Halide perovskites have emerged as disruptive semiconductors for applications including photovoltaics and light emitting devices, with modular optoelectronic properties realisable through composition and dimensionality tuning. Layered Ruddlesden-Popper perovskites of the form BA2MAn-1PbnI3n+1, where n is the number of lead-halide and methylammonium (MA) sheets spaced by longer butylammonium (BA) cations, are particularly interesting due to their unique two-dimensional character and charge carrier dynamics dominated by strongly bound excitons. However, long-range energy transport through excito…
Nanoscale investigations by scanning probe microscopy have provided major contributions to the rapid development of organic-inorganic halide perovskites (OIHP) as optoelectronic devices. Further improvement of device level properties requires a deeper understanding of the performance-limiting mechanisms such as ion migration, phase segregation and their effects on charge extraction both at the nano- and macroscale. Here, we have studied the dynamic electrical response of Cs0.05(FA0.83-MA0.17)0.95PbI3-xBrx perovskite structures by employing conventional and microsecond time-resolved Kelvin prob…
Adding a large A-site cation, such as dimethylammonium (DMA), to the perovskite growth solution has been shown to improve performance and long-term operational stability of halide perovskite solar cells. To better understand the origins of these improvements, we explore the changes in film structure, composition, and optical properties of a formamidinium (FA), Cs, Pb, mixed halide perovskite following addition of DMA to the perovskite growth solution in the ratio DMA0.1FA0.6Cs0.3Pb(I0.8Br0.2)3. Using time-of-flight secondary-ion mass spectrometry (TOF-SIMS) we show that DMA is indeed incorpora…
Organic-inorganic lead halide perovskites containing a mixture of iodide and bromide anions consistently perform better in donor-acceptor heterojunction solar cells than the standard methylammonium lead triiodide material. This observation is counterintuitive, as it is generally expected for photovoltaic materials that heterogeneities and compositional disorder cause reduced carrier diffusion length and conversion efficiency. Here, we combine ultrafast photoinduced electroabsorption and broadband fluorescence up-conversion spectroscopy measurements to scrutinize the carrier dynamics in mixed-c…
Point defects in metal halide perovskites play a critical role in determining their properties and optoelectronic performance; however, many open questions remain unanswered. In this work, we apply impedance spectroscopy and deep-level transient spectroscopy to characterize the ionic defect landscape in methylammonium lead triiodide ($MAPbI_3$) perovskites in which defects were purposely introduced by fractionally changing the precursor stoichiometry. Our results highlight the profound influence of defects on the electronic landscape, exemplified by their impact on the device built-in potentia…
Two-dimensional perovskites, in which inorganic layers are stabilized by organic spacer molecules, are attracting increasing attention as a more robust analogue to the conventional three-dimensional metal-halide perovskites. However, reducing the perovskite dimensionality alters their optoelectronic properties dramatically, yielding excited states that are dominated by bound electron-hole pairs known as excitons, rather than by free charge carriers common to their bulk counterparts. Despite the growing interest in two-dimensional perovskites for both light harvesting and light emitting applica…
In recent years, metal halide perovskites have generated tremendous interest for optoelectronic applications and their underlying fundamental properties. Due to the large electron-phonon coupling characteristic of soft lattices, self-trapping phenomena are expected to dominate hybrid perovskite photoexcitation dynamics. Yet, while the photogeneration of small polarons was proven in low dimensional perovskites, the nature of polaron excitations in technologically relevant 3D perovskites, and their influence on charge carrier transport, remain elusive. In this study, we used a combination of fir…
Halide perovskites perform remarkably in optoelectronic devices including tandem photovoltaics. However, this exceptional performance is striking given that perovskites exhibit deep charge carrier traps and spatial compositional and structural heterogeneity, all of which should be detrimental to performance. Here, we resolve this long-standing paradox by providing a global visualisation of the nanoscale chemical, structural and optoelectronic landscape in halide perovskite devices, made possible through the development of a new suite of correlative, multimodal microscopy measurements combining…
Surface-defect passivation is key to achieving high photoluminescence quantum yield in lead halide perovskite nanocrystals. However, in perovskite light-emitting diodes these surface ligands also have to enable balanced charge injection into the nanocrystals to yield high efficiency and operational lifetime. In this respect, alkaline halides have been reported to passivate surface trap states and increase the overall stability of perovskite light emitters. On the one side, the incorporation of alkaline ions into the lead halide perovskite crystal structure is considered to counterbalance catio…
Perovskite solar cells (PSCs) are attracting great attention as the most promising candidate for the next generation solar cells. This is due to their low cost and high power conversion efficiency in spite of their relatively short period of development. Key components of PSCs are a variety of halide perovskites with ABX3 stoichiometry used as a photoabsorber, which brought the factual breakthrough in the field of photovoltaic (PV) technology with their outstanding optoelectronic properties. To commercialize PSCs in the near future, however, these materials need to be further improved for a be…
Mixing halides in metal halide perovskites (MHPs) is an effective approach to adjust MHPs bandgap for applications in tandem solar cells. However, mixed-halide (MH-) MHPs undergo light-induced-phase-segregation (LIPS) under continuous illumination. Therefore, understanding the mechanism of LIPS is necessary for developing stable MH-MHPs. In this work, we investigated LIPS in layered (L) MHPs and discovered a critical role of spacer cations in LIPS. Through probing chemical changes of LIPS, we unveil light-induced-iodide-repulsion and the formation of Br-rich-phase in illuminated regions during…
Recently, halide perovskites have gained significant attention from the perspective of efficient spintronics owing to Rashba effect. This effect occurs as a consequence of strong spin-orbit coupling under noncentrosymmetric environment, which can be dynamic and/or static. However, there exist intense debates on the origin of broken inversion symmetry since the halide perovskites typically crystallize into a centrosymmetric structure. In order to clarify the issue, we examine both dynamic and static effects in the all-inorganic CsPbBr3 and organic-inorganic CH3NH3PbBr3 (MAPbBr3) perovskite sing…
The ultrafast polarization response to incident light and ensuing exciton/carrier generation are essential to outstanding optoelectronic properties of lead halide perovskites (LHPs). A large number of mechanistic studies in the LHP field to date have focused on contributions to polarizability from organic cations and the highly polarizable inorganic lattice. For a comprehensive understanding of the ultrafast polarization response, we must additionally account for the nearly instantaneous hyperpolarizability response to the propagating light field itself. While light propagation is pivotal to o…
Halide perovskites have recently gained widespread attention for their exceptional optoelectronic properties which have been illuminated by extensive spectroscopic investigations. In this article, nanophotonic surface-engineering using soft-lithography has been used to reproduce nanostructures with enhanced functionalities. A non-invasive optical technique based on Raman and photolumines-cence (PL) spectroscopy is employed to investigate the interactive effect of the thermal and optical behaviour in surface-patterned hybrid organic-inorganic halide perovskite thin films. The thermophys-ical pr…
Metal halide perovskites possess many physical properties amenable to optoelectronic applications, whereas the realization of these potentials has been hampered by their environmental and electronic instabilities. The morphological and molecular low dimensional perovskites and perovskite related materials have shown much promise in enhancing the chemical stability due to their unique molecular structures. Here we report on robust and reproducible four-terminal (4T) electrical measurements in a one-dimensional (1D) organic metal halide hybrid, (R)-α-methylbenzylammonium lead triiodide ((R-α-MBA…
The bandgap tunability of mixed-halide perovskites makes them promising candidates for light emitting diodes and tandem solar cells. However, illuminating mixed-halide perovskites results in the formation of segregated phases enriched in a single-halide. This segregation occurs through ion migration, which is also observed in single-halide compositions, and whose control is thus essential to enhance the lifetime and stability. Using pressure-dependent transient absorption spectroscopy, we find that the formation rates of both iodide- and bromide-rich phases in MAPb(BrxI1-x)3 reduce by two orde…
Investigation of the inherent field-driven charge transport behaviour of 3D lead halide perovskites has largely remained a challenging task, owing primarily to undesirable ionic migration effects near room temperature. In addition, the presence of methylammonium in many high performing 3D perovskite compositions introduces additional instabilities, which limit reliable room temperature optoelectronic device operation. Here, we address both these challenges and demonstrate that field-effect transistors (FETs) based on methylammonium-free, mixed-metal (Pb/Sn) perovskite compositions, that are wi…
Perovskite solar cells with record power conversion efficiency are fabricated by alloying both hybrid and fully inorganic compounds. While the basic electronic properties of the hybrid perovskites are now well understood, key electronic parameters for solar cell performance, such as the exciton binding energy of fully inorganic perovskites, are still unknown. By performing magneto transmission measurements, we determine with high accuracy the exciton binding energy and reduced mass of fully inorganic CsPbX$_3$ perovskites (X=I, Br, and an alloy of these). The well behaved (continuous) evolutio…
Halide perovskites have emerged recently as promising materials for many applications in photovoltaics and optoelectronics. Recent studies of their optical properties suggest many novel opportunities for a design of advanced nanophotonic devices due to low-cost fabrication, high values of the refractive index, existence of excitons at room temperatures, broadband bandgap tunability, high optical gain and nonlinear response, as well as simplicity of their integration with other types of structures. This paper provides an overview of the recent progress in the study of optical effects originatin…
Halide perovskites have attracted increasing research attention regarding their outstanding optoelectronic applications. Owing to its low activation energy, ion migration is implicated in the long-term stability and many unusual transport behaviors of halide perovskite devices. However, precise control of the ionic transport in halide perovskite crystals remains challenging. Here we visualized and quantified the electric-field-induced halide ion migration in an axial CsPbBr$_3$-CsPbCl$_3$ nanowire heterostructure and demonstrated a solid-state ionic rectification, which is due to the non-unifo…
Achieving control over the transport properties of charge-carriers is a crucial aspect of realizing high-performance electronic materials. In metal-halide perovskites, which offer convenient manufacturing traits and tunability for certain optoelectronic applications, this is challenging: The perovskite structure itself, poses fundamental limits to maximum dopant incorporation. Here, we demonstrate an organic modifier incorporation strategy capable of modulating the electronic density of states in halide tin perovskites without altering the perovskite lattice, in a similar fashion to substituti…
Meta-optics based on optically-resonant dielectric nanostructures is a rapidly developing research field with many potential applications. Halide perovskite metasurfaces emerged recently as a novel platform for meta-optics, and they offer unique opportunities for control of light in optoelectronic devices. Here we employ the generalized Kerker conditions to overlap electric and magnetic Mie resonances in each meta-atom of MAPbBr3 perovskite metasurface and demonstrate broadband suppression of reflection down to 4%. We reveal also that metasurface nanostructuring is also beneficial for the enha…
Recent observations indicated that the photoelectric conversion properties of perovskite materials are intimately related to the presence of superlattice structures and other unusual nanoscale features in them. The low dimensional or mixed dimensional halide perovskite family are found to be more efficient materials for device application compared to 3-dimensional halide perovskites. The emergence of perovskite solar cell has revolutionized the solar cell industry because of their flexible architecture and rapidly increased efficiency. Tuning the dielectric constant, charge separation are the …
Halide perovskites have indisputably exceptional optical and electronic properties, which are attractive for next-generation optoelectronic device technologies. We report on a reversible photoluminescence (PL) peak in iodide-based organic-inorganic lead halide perovskite materials under a two-photon absorption (TPA) process, while tuning the excitation wavelength. This phenomenon occurs when the incoming femtosecond (fs) laser photon energy is higher than a threshold energy. Intriguingly, this phenomenon also occurs in other kinds of iodide perovskite materials. Moreover, two more shorter wave…
