Suppression of beam losses is essential for successful operation of high-intensity linac. Historically, the values of the field amplitudes and phases of the side-coupled, 805-MHz LANSCE linac modules are maintained using a well-known delta-t tuning procedure. Transverse matching of the beam with accelerator is performed through adjustments of beam ellipses in 4D phase space with accelerator lattice using matching quadrupoles. Control of the beam-energy ramp along the length of a proton linear accelerator is required to improve tune of accelerator and decrease beam losses. Time-of-flight measurements of the H- beam energy are now being used to confirm and improve the overall control of the energy ramp along the linac. The time-of-flight method utilizes absolute measurements of beam energy using direct signals from beam at an oscilloscope, as well as the difference in RF phases measured as the beam passes installed delta-t pickup loops. A newly developed BPPM data acquisition system is used. Beam energy measurement along accelerator together with phase scans, klystrons output power control, and delta-t method, allow tuning of accelerator much more close to original design and reduce losses generated by linac. Details of the upgraded tuning procedure and results of tuning and operation are presented.
The Fusion Prototypic Neutron Source (FPNS) is considered to be a testbed for scientific understanding of material degradation in future nuclear fusion reactors [1-3]. The primary mission of FPNS is to provide a damage rate in iron samples of 8-11 dpa/calendar year with He/dpa ratio of ~10 appm in irradiation volume of 50 cm3 or larger with irradiation temperature 300 - 1000o C and flux gradient less than 20%/cm in the plane of the sample. The Los Alamos Neutron Science Center (LANSCE) is an attractive candidate for the FPNS project. The Accelerator Facility was designed and operated for an ex…
The linear accelerator (LINAC) at the Los Alamos Neu-tron Science Center (LANSCE) consists of Pre-buncher, Main-Buncher, low-energy beam transport (LEBT), four 201.25-MHz Drift Tube Linacs (DTLs) and forty-four 805-MHz Coupled Cavity Linacs (CCLs). As a part of the upcoming LANSCE Modernization project, low-level RF (LLRF) systems of four 201-MHz DTLs and twenty-six 805-MHz SCLs have been digitized. Hence the net-work-based control of the cavity field and RF commis-sioning are possible. Each LLRF and high-power RF (HPRF) systems have many process variables (PVs) lo-cated on different computer …
The 750-keV low-energy beam transport of the Los Alamos Neutron Science Center (LANSCE) linac consists of two independent beam lines that facilitate simultaneous injection of H+ and H- beams into the linear accelerator. The efficiency of beam transport within this structure is largely controlled by the effects of space-charge neutralization. In this paper, we report a series of experiments that were performed to determine the level, as well as the required timescale for the onset of beam space charge neutralization. Measurements performed along the structure indicate significant variation of n…
Incremental upgrades of the legacy low level RF (LLRF) equipment-50 years for the Los Alamos Neutron Science Center (LANSCE)-involves challenges and problems not seen with new and total replacement opportunities. The digital LLRF upgrade at LANSCE has deployed 30 of the 53 required systems as of September 2022. This paper describes the performance of the digital upgrade, current status, and future installations along with the technical challenges, including unexpected challenges, associated with deploying new digital systems in conjunction with legacy analog equipment. In addition, this paper …
The front end of Los Alamos Neutron Science Center (LANSCE) linear accelerator uses four 201.25-MHz Drift-Tube Linacs (DTLs) to accelerate the H+ and H- beams to 100 MeV. Three of the 201.25-MHz DTLs are powered by diacrodes and the first DTL is powered by a tetrode. A 20-kW solid-state power amplifier (SSPA) is used to provide ~15 kW drive power to the tetrode. The SSPA is water-cooled and consists of 24 push-pull LDMOS transistors operating at 45% of their power saturation capability, providing ample power headroom and excellent linearity. However, the phase of the SSPA is perturbed at +/-20…
Radio frequency (RF) windows are historically a point where failure occurs in input-power couplers for accelerators. To understand more about the reliability of high power RF windows, lifetime testing was done on 700 MHz coaxial RF windows for the Low Energy Demonstration Accelerator (LEDA) project of the Accelerator Production of Tritium (APT) program. The RF windows, made by Marconi Applied Technologies (formerly EEV), were tested at 800 kW for an extended period of time. Changes in the reflected power, vacuum, air outlet temperature, and surface temperature were monitored over time. The res…
This paper describes the construction and operational status of an accelerator test facility for Project X. The purpose of this facility is for Project X component development activities that benefit from beam tests and any development activities that require 325 MHz or 650 MHz RF power. It presently includes an H- beam line, a 325 MHz superconducting cavity test facility, a 325 MHz (pulsed) RF power source, and a 650 MHz (CW) RF power source. The paper also discusses some specific Project X components that will be tested in the facility.
Los Alamos is currently developing novel particle accelerator controls and diagnostics algorithms to enable higher quality beams with lower beam losses than is currently possible. The purpose of this workshop was to consider tuning and optimization challenges of a wide range of particle accelerators including linear proton accelerators such as the Los Alamos Neutron Science Center (LANSCE), rings such as the Advanced Photon Source (APS) synchrotron, free electron lasers (FEL) such as the Linac Coherent Light Source (LCLS) and LCLS-II, the European X-ray Free Electron Laser (EuXFEL), the Swiss …
A high-intensity continuous wave (CW) radio frequency quadrupole (RFQ) accelerator is designed for boron neutron capture therapy (BNCT). The transmission efficiency of a 20-mA proton beam accelerated from 30 keV to 2.5 MeV can reach 98.7% at an operating frequency of 200 MHz. The beam dynamics has good tolerance to errors. By comparing the high-frequency parameters of quadrilateral and octagonal RFQ cross-sections, the quadrilateral structure of the four-vane cavity is selected owing to its multiple advantages, such as a smaller cross section at the same frequency and easy processing. In addit…
Linear accelerators containing the sequence of independently phased cavities with constant geometrical velocity along each structure are widely used in practice. The chain of cavities with identical cell lengths is utilized within a certain beam velocity range, with subsequent transformation to the next chain with higher cavity velocity. Design and analysis of beam dynamics in this type of accelerator are usually performed using numerical simulations. A full theoretical description of particle acceleration in an array of independent phased cavities has not been developed. In the present paper,…
We are currently operating the front end of the accelerator production of tritium (APT) accelerator, a 7 MeV radio frequency quadrapole (RFQ) using three, 1.2 MW CW klystrons. These klystrons are required and designed to dissipate the full beam power in the collector. The klystrons have less than 1500 operational hours. One collector has failed and all collectors are damaged. This paper will discuss the damage and the difficulties in diagnosing the cause. The collector did not critically fail. Tube operation was still possible and the klystron operated up to 70% of full beam power with excelle…
A concept of a 650 MHz CW magnetron transmitter with fast control in phase and power, based on two-stage injection-locked CW magnetrons, has been proposed to drive Superconducting Cavities (SC) for intensity-frontier accelerators. The concept is based on a theoretical model considering a magnetron as a forced oscillator and experimentally verified with a 2.5 MW pulsed magnetron. To fulfill fast control of phase and output power requirements of SC accelerators, both two-stage injection-locked CW magnetrons are combined with a 3-dB hybrid. Fast control in output power is achieved by varying the …
The accelerator for the APT Project is a 100 mA CW proton linac with an output energy of 1030 MeV. A High Energy Beam Transport (HEBT) conveys the beam to a raster expander, that provides a large rectangular distribution at a target/blanket (T/B) assembly. Spallation neutrons generated by the proton beam in the T/B reacts with Helium-3 to produce tritium. The design of the APT linac is an integrated normal-conducting (NC)/superconducting (SC) proton linac; the machine architecture has been discussed elsewhere [1]. The NC linac consists of a 75 keV injector, a 6.7-MeV 350-MHz RFQ (radio frequen…
Bridging Metal Additive Manufacturing and RF Accelerator Design: Development of a 704.4 MHz Crossbar H-Mode Linac for Efficient Beam Acceleration
GSI Helmholtzzentrum für Schwerionenforschung（GSI亥姆霍兹重离子研究中心）；Institute for Applied Physics, Goethe-University Frankfurt（法兰克福歌德大学应用物理研究所）；Helmholtz Research Academy Hesse for FAIR（黑森亥姆霍兹FAIR研究院）
The high-power RF systems for the Accelerator Production of Tritium (APT) program require high-power circulators at 350 MHz and 700 MHz to protect 1 MW Continuous Wave (CW) klystrons from reflected power. The 350 MHz circulator is based on the CERN, ESRF, and APS designs and has performed very well. The 700 MHz circulator is a new design. Prototype 700 MHz circulators have been high-power tested at Los Alamos National Laboratory (LANL). The first of these circulators has satisfied performance requirements. The circulator requirements, results from the testing, and lessons learned from this dev…
We consider acceleration light ions by the field of a traveling-wave in a helical waveguide. The frequency of the accelerating RF field f = 100 MHz, generator power P = 2 MW. Ion focusing is provided by a solenoidal magnetic field with the intensity B = 3.5 Tesla. With increasing the accelerator length up to L = 15 m, the final energy of the ions can be increased up to a value of E = 7 MeV / nucleon.
The Low-Energy Demonstration Accelerator (LEDA) radio-frequency quadrupole (RFQ) is a 100% duty factor (CW) linac that delivers >100 mA of H+ beam at 6.7 MeV. The 8-m-long, 350-MHz RFQ structure accelerates a dc, 75-keV, 110-mA H+ beam from the LEDA injector with >90% transmission. LEDA [1,2] consists of a 75-keV proton injector, 6.7-MeV, 350-MHz CW RFQ with associated high-power and low-level rf systems, a short high-energy beam transport (HEBT) and high-power (670-kW CW) beam stop. The beam emittance is inferred from wire scanner measurements of the beam profile at a single location in the H…
Two superconducting quarter-wave resonator (QWR) prototypes have been fabricated and tested. They operate at 80.5 MHz and 161 MHz and are optimised for beta = 0.085 and beta = 0.16, respectively. The prototypes are simplified versions without integrated helium vessels. In the first RF tests, the beta = 0.085 QWR reached a peak surface electric field (Ep) in excess of 30 MV/m, with an intrinsic quality factor (Q0) in excess of 1E9 at the design field of Ep = 20 MV/m. The beta = 0.16 QWR reached Ep = 20 MV/m with Q0 = 2.5E9. It is suspected that the performance of the latter cavity can be improv…
The 3 MV Tandem Pelletron accelerator at the Spanish Accelerator Laboratory (CNA) has been recently upgraded to produce pulsed ion beams for neutron Time-Of-Flight (TOF) measurements. The upgrade has consisted of two actions: a pulsing system installed at the low energy part of the Tandem accelerator and a new line fully equipped. The pulsing system provides approximately one nanosecond pulse width of protons with variable repetition rates from kHz down to MHz. The new line is equipped with conventional devices and a pick-up for timing measurements with high resolution. The properties of the w…
A neutron source is proposed. It is based on a proton accelerator with the energy Ep = 1.2 GeV, current Ip = 0.7A, pulse duration T = 3 mcsec, repetition rate F = 60 Hz, and accelerator length L = 30 m. Protons are accelerated by the field of electron rings. The electron rings are formed from a tube beam by way of modulation and creating rotating motion by crossing the magnetic field cusp. The frequency of modulation f1 = 142.8 MHz. The bunch is accelerated at the frequency f3 = 2856 MHz. The high frequency power required for making the field is P1 = 6 - 150 MW/section, the power transferred t…
Linear Induction Accelerator (LIA) is a unique type of accelerator, which is capable to accelerate kiloAmpere charged particle current to tens of MeV energy. The present development of LIA in MHz busting mode and successful application into synchrotron broaden LIAs usage scope. Although transformer model is widely used to explain the acceleration mechanism of LIAs, it is not appropriate to consider the induction electric field as the field which accelerates charged particles for many modern LIAs. Authors examined the transition of the magnetic cores functions during LIA acceleration modules ev…
For NOvA and future experiments requiring high intensity proton beams, Fermilab is in the process of upgrading the existing accelerator complex for increased proton production. One such improvement is to reduce the Main Injector cycle time, by performing slip stacking, previously done in the Main Injector, in the now repurposed Recycler Ring. Recycler slip stacking requires new tuneable RF cavities, discussed separately in these proceedings. These are quarter wave cavities resonant at 52.809 MHz with a 10 kHz tuning range. The 10 kHz range is achieved by use of a tuner which has an electrical …
We consider acceleration of protons in a cavity with such dimensions as length l = 10 m, width b = 20 m, height a = 1.01 m, located between two bending (180)degree magnets with isochronous magnetic field. The cavity is loaded with rows of drift plates (tubes), being excited by a wave of E110 type at the frequency fo = 148.5 MHz, excitation power P1 = 5.65 MW. Additionally, the cavity is fed with the power P2 = 8 MW, transmitted into a beam of protons with such parameters as the final energy 0.8 GeV, pulse beam current I = 10 mA, pulse width 25 microseconds, repetition rate 10 Hz. We discuss th…
For NOvA and future experiments requiring high intensity proton beams, Fermilab is in the process of upgrading the existing accelerator complex for increased proton production. One such improvement is to reduce the Main Injector cycle time, by performing slip stacking, previously done in the Main Injector, in the now repurposed Recycler Ring. Recycler slip stacking requires two new RF cavities operating at slightly different frequencies (df = 1260Hz). These are copper, coaxial, quarter wave cavities with R/Q =13 ohms. They operate at a peak gap voltage of 150 kV with 150 kW peak drive power (6…
The research note presents results of coupled RF and thermal simulation of a cryocooler conduction cooled 650 MHz SRF cavity made of bulk niobium and coated with Nb3Sn on the RF surface. The cavity is part of a particle accelerator design capable of producing 10 MeV, 1000 kW electron beam for application in wastewater treatment. More details of the accelerator design are presented in R.C. Dhuley et al. (2022) Phys. Rev. Accel. Beams 25, 041601.
The 75-keV injector and 6.7-MeV RFQ that comprise the first portion of the cw, 100-mA proton linac for the accelerator production of tritium (APT) project have been built and operated. The LEDA RFQ has been extensively tested for pulsed and cw output-beam currents <=100 mA. Up to 2.2 MW of cw rf power from the 350-MHz rf system is coupled into the RFQ, including 670 kW for the cw proton beam. The emittance for a 93-mA pulsed RFQ output beam, as determined from quadrupole-magnet-scan measurements, is ex x ey = 0.25 x 0.31 (pi mm mrad)2 [rms normalized]. A follow-on experiment, to intentionally …
Electro-optical detection has proven to be a valuable technique to study temporal profiles of THz pulses with pulse durations down to femtoseconds. As the Coulomb field around a relativistic electron bunch resembles the current profile, electro-optical detection can be exploited for non-invasive bunch length measurements at accelerators. We have developed a very compact and robust electro-optical detection system based on spectral decoding for bunch length monitoring at the European XFEL with single-shot resolution better than 200~fs. Apart from the GaP crystal and the corresponding laser opti…
The China ADS (C-ADS) project is proposed to build a 1000 MW Accelerator Driven sub-critical System around 2032. The accelerator will work in CW mode with 10 mA in beam current and 1.5 GeV in final beam energy. The linac is composed of two major sections: the injector section and the main linac section. There are two different schemes for the injector section. The Injector-I scheme is based on a 325-MHz RFQ and superconducting spoke cavities of same RF frequency and the Injector-II scheme is based on a 162.5-MHz RFQ and superconducting HWR cavities of same frequency. The main linac design will…
The Korea Multipurpose Accelerator Complex (KOMAC) has been developing a 300-kV test stand for a 1-MV electrostatic accelerator ion source. The ion source and accelerating tube will be installed in a high-pressure vessel. The ion source in the high-pressure vessel is required to have a high reliability. The test stand has been proposed and developed to confirm the stable operating conditions of the ion source. The ion source will be tested at the test stand to verify the long-time operating conditions. The test stand comprises a 300-kV high-voltage terminal, a battery for the ion-source power,…
The radiofrequency resonant four-quadrant mechanical structure of a 4-vane Radio Frequency Quadrupole (RFQ) has a high quality factor and narrow bandwidth, resulting in high sensitivity to frequency detuning caused by thermal expansion under high power operation, so minimization of frequency errors and affording dynamic tuning are very important design issues. Here we describe an optimization approach to figure out a suitable cooling design for a 4-vane RFQ in steady state. Besides, we investigate how the accelerator responds in transient thermal analysis that could help to guide commissioning…
High-frequency linear accelerators are very suitable for carbon ion therapy, thanks to the reduced operational costs and the high beam quality with respect to synchrotrons, which are presently the only available technology for this application. In the framework of the development of a new linac for carbon ion therapy, this article describes the design of a compact 750 MHz Radio Frequency Quadrupole (RFQ) with trapezoidal vanes. A new semi-analytic approach to design the trapezoidal-vane RFQ is introduced together with the relevant beam dynamics properties. The RFQ is split into two decoupled r…
High-bunch-charge photoemission electron-sources operating in a continuous wave (CW) mode are required for many advanced applications of particle accelerators, such as electron coolers for hadron beams, electron-ion colliders, and free-electron lasers (FELs). Superconducting RF (SRF) has several advantages over other electron-gun technologies in CW mode as it offers higher acceleration rate and potentially can generate higher bunch charges and average beam currents. A 112 MHz SRF electron photoinjector (gun) was developed at Brookhaven National Laboratory (BNL) to produce high-brightness and h…
Beam matching is a common technique that is routinely employed in accelerator design with the aim of minimizing beam losses and preservation of beam brightness. Despite being widely used, a full theoretical understanding of beam matching in 6D remains elusive. Here, we present an analytical treatment of 6D beam matching of a high-intensity beam onto an RF structure. We begin our analysis within the framework of a linear model, and apply the averaging method to a set of 3D beam envelope equations. Accordingly, we obtain a matched solution that is comprised of smoothed envelopes and periodic ter…
Superconducting cavities with low RF frequencies and heavy damping of higher order modes (HOM) are desired for the main accelerator of High Energy Photon Source (HEPS), a 6 GeV synchrotron light source promising ultralow emittance currently under construction in Beijing. A compact 166.6 MHz superconducting cavity was proposed adopting a quarter-wave beta=1 geometry. Based on the successful development of a proof-of-principle cavity, a HOM-damped 166.6 MHz compact superconducting cavity was subsequently designed. A ferrite damper was installed on the beam pipe to reduce HOM impedance below the …
Compact accelerator-based neutron source facilities are garnering attention and play an important and expanding role in material and engineering sciences, as well as in neutron science education and training. Neutrons are produced by bombarding a low-energy proton beam onto a beryllium or lithium target. In such an accelerator-based neutron source, a radio frequency quadrupole (RFQ) is usually utilized to accelerate a high-intensity proton beam to a few MeV. This study mainly covers the high-frequency structure design optimizations of a 4-vane RFQ with pi-mode stabilizer loops (PISLs) and its …
LINAC 4 is a normal conducting H- structure proposed to intensify the proton flux currently available for the CERN accelerator chain. This linac is designed to accelerate a 65 mA beam up to 160 MeV to be injected into the CERN Proton Synchrotron Booster. The acceleration is performed up to 3 MeV by a Radio-Frequency Quadrupole resonating at 352 MHz followed by a serie of two drift tube systems (conventional Alvarez and Cell Coupled Drift Tube Linac) boosting the beam up to 90 MeV at 352 MHz and finished by a Side Coupled Linac at 704 MHz. Beam dynamics was studied and optimized performing end-…
The Spallation Neutron Source (SNS) is being designed for operation in 2004. The SNS is a 1 GeV machine consisting of a combination normal-conducting and super-conducting linac as well as a ring and target area. The linac front end is a 402.5 MHz RFQ being developed by Lawrence Berkeley Lab. The DTL (at 402.5 MHz) and the CCL (at 805 MHz) stages are being developed by Los Alamos National Laboratory. The expected output energy of the DTL is 87 MeV and that of the CCL is 185 MeV. The RF control system under development for the linac is based on the Low Energy Demonstration Accelerator (LEDA) con…
As the second stage of the CEPC-SPPC project, SPPC (Super Proton-Proton Collider) aims at exploring new physics beyond the Standard Model. The key design goal for the SPPC accelerator complex is to reach 75 TeV in center of mass energy with a circumference of 100 km for the collider and an injector chain of four accelerators in cascade to support the collider. As an important part of the SPPC conceptual study, the longitudinal beam dynamics was studied systematically, which includes the dynamics in the collider and its complex injector chain. First, the bunch filling scheme of the SPPC complex…
Dielectric disk accelerating (DDA) structures are being studied as an alternative to conventional disk-loaded copper structures. This paper investigates numerically an efficient X-band DDA structure operating at a higher order mode of TM02-π. This accelerating structure consists of dielectric disks with irises arranged periodically in a metallic enclosure. Through optimizations, the RF power loss on the metallic wall can be significantly reduced, resulting in an extremely high quality factor Q_0=111064 and a very high shunt impedance R_shunt=605 MΩ/m. The RF-to-beam power efficiency reaches 46…
Luminosity-driven channeling extraction has been observed for the first time in a 900 GeV study at the Fermilab Tevatron. This experiment, Fermilab E853, demonstrated that useful TeV level beams can be extracted from a superconducting accelerator during high luminosity collider operations without unduly affecting the background at the collider detectors. Multi-turn extraction was found to increase significantly the efficiency of the process. The beam extraction efficiency was about 25%. Studies of time dependent effects found that the turn-to-turn structure was governed mainly by accelerator b…
The PIP-II project is a program to upgrade the Fermilab accelerator complex. The PIP-II linac includes a 2.1 MeV Medium Energy Beam Transport (MEBT) section that incorporates a unique chopping system to perform arbitrary, bunch-by-bunch removal of 162.5 MHz structured beam. The MEBT chopping system will consist of two identical kickers working together and a beam absorber. One design of two having been proposed has been a 200 Ohm characteristic impedance traveling wave dual-helix kicker driven with custom designed high-speed switches. This paper reports on the first performance results of one …
High Q-factors are of utmost importance to minimize losses of superconducting radio-frequency cavities deployed in continuous wave particle accelerators. This study elucidates the surface treatment that can maximize the Q-factors in high-beta 650 MHz elliptical niobium cavities. State-of-the-art surface treatments are applied in many single-cell cavities, and surface resistance studies are performed to understand the microwave dissipation at this unexplored frequency. The nitrogen doping treatment is confirmed to be necessary to maximize the Q-factors at medium RF fields. We applied this treat…
LINAC 4 is a normal conducting H- linac proposed at CERN to provide a higher proton flux to the CERN accelerator chain. It should replace the existing LINAC 2 as injector to the Proton Synchrotron Booster and can also operate in the future as the front end of the SPL, a 3.5 GeV Superconductingg Proton Linac. LINAC 4 consists of a Radio-Frequency Quadrupole, a chopper line, a Drift Tube Linac (DTL) and a Cell Coupled DTL all operating at 352 MHz and finally a Side Coupled Linac at 704 MHz. Beam dynamics was studied and optimized performing end-to-end simulations. This paper presents statistical…
There's presently a growing demand for high current proton and deuteron linear accelerators based on superconducting technology to better support various fields of science. A \b{eta}=0.09 162.5 MHz high current superconducting half wave resonator (HWR) has been designed at Peking University to accelerate 100 mA proton beam or 50 mA deuteron beam after the RFQ accelerating structure. The detailed electromagnetic design, multipacting simulation, mechanical analysis of the cavity will be given in this paper.
We report results of the beam commissioning and first operation of the 1.3 GHz superconducting RF electron linear accelerator at Fermilab Accelerator Science and Technology (FAST) facility. Construction of the linac was completed and the machine was commissioned with beam in 2017. The maximum total beam energy of about 300 MeV was achieved with the record energy gain of 250 MeV in the ILC-type SRF cryomodule. The photoinjector was tuned to produce trains of 200 pC bunches with a frequency of 3 MHz at a repetition rate of 1 Hz. This report describes the aspects of machine commissioning such as …
Recently, the Low-Energy Demonstration Accelerator (LEDA) portion of the Accelerator Production of Tritium (APT) project reached its 100-mA, 8-hr CW beam operation milestone. LEDA consists of a 75-keV proton injector, 6.7-MeV, 350-MHz CW radio-frequency quadrupole (RFQ) with associated high-power and low-level rf systems, a short high-energy beam transport (HEBT) and high-power (670-kW CW) beam dump. During the commissioning phase it was discovered that the RFQ field level must to be approximately 5-10% higher than design in order to accelerate the full 100-mA beam with low losses. Measurement…
We summarize the current state of a concept for muon acceleration aimed at a future Neutrino Factory. The main thrust of these studies was to reduce the overall cost while maintaining performance by exploring the interplay between the complexity of the cooling systems and the acceptance of the accelerator complex. To ensure adequate survival for the short-lived muons, acceleration must occur at high average gradient. The need for large transverse and longitudinal acceptances drives the design of the acceleration system to an initially low RF frequency, e.g., 325 MHz, which is then increased to…
