In this work, we employ multiple energy harvesting relays to assist information transmission from a multi-antenna hybrid access point (HAP) to a receiver. All the relays are wirelessly powered by the HAP in the power-splitting (PS) protocol. We introduce the novel concept of hybrid relay communications, which allows each relay to switch between two radio modes, i.e., the active RF communications and the passive backscatter communications, according to its channel and energy conditions. We envision that the complement transmissions in two radio modes can be exploited to improve the overall relay performance. As such, we aim to jointly optimize the HAP's beamforming, individual relays' radio mode, the PS ratio, and the relays' collaborative beamforming to enhance the throughput performance at the receiver. The resulting formulation becomes a combinatorial and non-convex problem. Thus, we firstly propose a convex approximation to the original problem, which serves as a lower bound of the relay performance. Then, we design an iterative algorithm that decomposes the binary relay mode optimization from the other operating parameters. In the inner loop of the algorithm, we exploit the structural properties to optimize the relay performance with the fixed relay mode in the alternating optimization framework. In the outer loop, different performance metrics are derived to guide the search for a set of passive relays to further improve the relay performance. Simulation results verify that the hybrid relaying communications can achieve 20% performance improvement compared to the conventional relay communications with all active relays.
The performance of cooperative ambient backscatter communications (CABC) can be enhanced by employing reconfigurable intelligent surface (RIS) to assist backscatter transmitters. Since the RIS power consumption is a non-negligible issue, we consider a RIS assisted CABC system where the RIS with energy harvesting circuit can not only reflect signal but also harvest wireless energy. We study a transmission design problem to minimize the RIS power consumption with the quality of service constraints for both active and backscatter transmissions. The optimization problem is a mixed-integer non-conv…
Spectrum sharing backscatter communication systems are among the most prominent technologies for ultralow power and spectrum efficient communications. In this paper, we propose an underlay spectrum sharing backscatter communication system, in which the secondary network is a backscatter communication system. We analyze the performance of the secondary network under a transmit power adaption strategy at the secondary transmitter, which guarantees that the interference caused by the secondary network to the primary receiver is below a predetermined threshold. We first derive a novel analytical e…
Low-power ambient backscatter communication (AmBC) relying on radio-frequency (RF) energy harvesting is an energy-efficient solution for batteryless Internet of things (IoT). However, ambient backscatter signals are severely faded by dyadic backscatter channel (DBC), limiting connectivity in conventional orthogonal time-division-based AmBC (TD-AmBC). In order to support massive connectivity in AmBC, we propose sparse-coded AmBC (SC-AmBC) based on non-orthogonal signaling. Sparse code utilizes inherent sparsity of AmBC where power supplies of RF tags rely on ambient RF energy harvesting. Conseq…
Ambient backscatter communications (AmBackComs) have been recognized as a spectrum- and energy-efficient technology for Internet of Things, as it allows passive backscatter devices (BDs) to modulate their information into the legacy signals, e.g., cellular signals, and reflect them to their associated receivers while harvesting energy from the legacy signals to power their circuit operation. {\color{black} However, the co-channel interference between the backscatter link and the legacy link and the non-linear behavior of energy harvesters at the BDs have largely been ignored in the performance…
Wirelessly powered backscatter communication (WPBC) has been identified as a promising technology for low-power communication systems, which can reap the benefits of energy beamforming to improve energy transfer efficiency. However, existing studies on energy beamforming fail to simultaneously take energy supply and information transfer in WPBC into account. This paper takes the first step to fill this gap, by considering the restrictive relationship between the energy harvesting rate and achievable rate with estimated backscatter channel state information (BS-CSI). To ensure reliable communic…
Unmanned aerial vehicle (UAV) has been widely adopted in wireless systems due to its flexibility, mobility, and agility. Nevertheless, a limited onboard battery greatly hinders UAV to prolong the serving time from communication tasks that need a high power consumption in active RF communications. Fortunately, caching and backscatter communication (BackCom) are appealing technology for energy efficient communication systems. This motivates us to investigate a wireless communication network with backscatter- and cache-assisted UAV technology. We assume a UAV with a cache memory is deployed as a …
Self-sustainable communications based on advanced energy harvesting technologies have been under rapid development, which facilitate autonomous operation and energy-efficient transmission. Recently, ambient backscattering that leverages existing RF signal resources in the air has been invented to empower data communication among low-power devices. In this paper, we introduce hybrid device-to-device (D2D) communications by integrating ambient backscattering and wireless-powered communications. The hybrid D2D communications are self-sustainable, as no dedicated external power supply is required.…
In the present contribution, we propose a novel opportunistic ambient backscatter communication (ABC) framework for radio frequency (RF)-powered cognitive radio (CR) networks. This framework considers opportunistic spectrum sensing integrated with ABC and harvest-then-transmit (HTT) operation strategies. Novel analytic expressions are derived for the average throughput, the average energy consumption and the energy efficiency in the considered set up. These expressions are represented in closed-form and have a tractable algebraic representation which renders them convenient to handle both anal…
This letter introduces a novel wireless-powered backscatter communication system which allows sensors to utilize RF signals transmitted from a dedicated RF energy source to transmit data. In the proposed system, when the RF energy source transmits RF signals, the sensors are able to backscatter the RF signals to transmit date to the gateway and/or harvest energy from the RF signals for their operations. By integrating backscattering and energy harvesting techniques, we can optimize the network throughput of the system. In particular, we first formulate the time scheduling problem for the syste…
In this paper, we investigate optimal scheme to manage time scheduling of different modules including spectrum sensing, radio frequency (RF) energy harvesting (RFH) and ambient backscatter communication (ABCom) by maximizing data transmission rate in the internet of things (IoT). We first consider using spectrum sensing with energy detection techniques to detect high power ambient RF signals, and then performing RFH and ABCom with them. Specifically, to improve the spectrum sensing efficiency, compressive sensing is used to detect the wideband RF singals. We propose a joint optimization proble…
With the emerging Internet-of-Things services, massive machine-to-machine (M2M) communication will be deployed on top of human-to-human (H2H) communication in the near future. Due to the coexistence of M2M and H2H communications, the performance of M2M (i.e., secondary) network depends largely on the H2H (i.e., primary) network. In this paper, we propose ambient backscatter communication for the M2M network which exploits the energy (signal) sources of the H2H network, referring to traffic applications and popularity. In order to maximize the harvesting and transmission opportunities offered b…
Future Internet-of-Things (IoT) will connect billions of small computing devices embedded in the environment and support their device-to-device (D2D) communication. Powering this massive number of embedded devices is a key challenge of designing IoT since batteries increase the devices' form factors and their recharging/replacement is difficult. To tackle this challenge, we propose a novel network architecture that integrates wireless power transfer and backscatter communication, called wirelessly powered backscatter communication (WP-BC) networks. In this architecture, power beacons (PBs) are…
Motivated by the recent advances in the Internet of Things (IoT) and in Wireless Power Transfer (WPT), we study a network architecture that consists of power beacons (PBs) and passive backscatter nodes (BNs). The PBs transmit a sinusoidal continuous wave (CW) and the BNs reflect back a portion of this signal while harvesting the remaining part. A BN harvests energy from multiple nearby PBs and modulates its information bits on the composite CW through backscatter modulation. The analysis poses real challenges due to the double fading channel, and its dependence on the PPPs of both the BNs and …
Future Internet-of-Things (IoT) is expected to wirelessly connect billions of low-complexity devices. For wireless information transfer (WIT) in IoT, high density of IoT devices and their ad hoc communication result in strong interference which acts as a bottleneck on WIT. Furthermore, battery replacement for the massive number of IoT devices is difficult if not infeasible, making wireless energy transfer (WET) desirable. This motivates: (i) the design of full-duplex WIT to reduce latency and enable efficient spectrum utilization, and (ii) the implementation of passive IoT devices using backsc…
Intelligent reflecting surface (IRS) has recently been emerged as an effective way for improving the performance of wireless networks by reconfiguring the propagation environment through a large number of passive reflecting elements. This game-changing technology is especially important for stepping into the Internet of Everything (IoE) era, where high performance is demanded with very limited available resources. In this paper, we study a backscatter-assisted wireless powered communication network (BS-WPCN), in which a number of energy-constrained users, powered by a power station (PS), trans…
The next generation Internet of Things (IoT) exhibits a unique feature that IoT devices have different energy profiles and quality of service (QoS) requirements. In this paper, two energy and spectrally efficient transmission strategies, namely wireless power transfer assisted non-orthogonal multiple access (WPT-NOMA) and backscatter communication assisted NOMA (BAC-NOMA), are proposed by utilizing this feature of IoT and employing spectrum and energy cooperation among the devices. Furthermore, for the proposed WPT-NOMA scheme, the application of hybrid successive interference cancelation (SIC…
Wireless power transfer (WPT) using energy beamforming is a promising solution for low power Internet of Things (IoT) devices. In this work, we consider WPT from an energy transmitter (ET) employing retrodirective WPT using a large phased antenna array to an energy receiver (ER) capable of ambient backscatter. The advantage of retrodirective WPT is that no explicit channel estimation is needed at the ET and the use of ambient backscattering eliminates the need for active transmission at the ER. We propose a training sequence design, i.e., pattern of varying the reflection coefficient at the ER…
In this paper, we study the optimal resource allocation algorithm design for large intelligent reflecting surface (IRS)-assisted simultaneous wireless information and power transfer (SWIPT) systems. To facilitate efficient system design for large IRSs, instead of jointly optimizing all the IRS elements, we partition the IRS into several tiles and employ a scalable optimization framework comprising an offline design stage and an online optimization stage. In the offline stage, the IRS elements of each tile are jointly designed to support a set of different phase shift configurations, referred t…
Over the last decade, simultaneous wireless information and power transfer (SWIPT) has become a practical and promising solution for connecting and recharging battery-limited devices, thanks to significant advances in low-power electronics technology and wireless communications techniques. To realize the promised potentials, advanced resource allocation design plays a decisive role in revealing, understanding, and exploiting the intrinsic rate-energy tradeoff capitalizing on the dual use of radio frequency (RF) signals for wireless charging and communication. In this paper, we provide a compre…
In this paper, we study an active IRS-aided simultaneous wireless information and power transfer (SWIPT) system. Specifically, an active IRS is deployed to assist a multi-antenna access point (AP) to convey information and energy simultaneously to multiple single-antenna information users (IUs) and energy users (EUs). Two joint transmit and reflect beamforming optimization problems are investigated with different practical objectives. The first problem maximizes the weighted sum-power harvested by the EUs subject to individual signal-to-interference-plus-noise ratio (SINR) constraints at the I…
