This paper presents a deep learning (DL) approach for estimating and detecting symbols in signals transmitted through reconfigurable intelligent surfaces (RIS). The proposed network utilizes fully connected layers to estimate channels and phase angles from a reflected signal received through an RIS. Because the proposed network can estimate and detect symbols without any pilot signaling, this method reduces the overhead required for transmission. The improvements achieved by this method are quantified in terms of the bit-error rate, outperforming traditional detectors.
Massive MIMO Channel-aware Decision Fusion Aided by Reconfigurable Intelligent Surfaces
University of Naples Federico II（那不勒斯费德里科二世大学）；University of Cassino and Southern Lazio（卡西诺与南拉齐奥大学）；CNIT（意大利电信与信息技术研究中心）；CentraleSupélec（中央理工-高等电力学院）；CNRS（法国国家科学研究中心）；Université Paris-Saclay（巴黎萨克雷大学）；University of Luxembourg（卢森堡大学）
By reconfiguring the propagation environment of electromagnetic waves artificially, reconfigurable intelligent surfaces (RISs) have been regarded as a promising and revolutionary hardware technology to improve the energy and spectrum efficiency of wireless networks. In this paper, we study a RIS aided multiuser multiple-input single-output (MISO) wireless power transfer (WPT) system, where the transmitter is equipped with a constant-envelope analog beamformer. We formulate a novel problem to maximize the total received power of all the users by jointly optimizing the beamformer at transmitter …
Reconfigurable intelligent surfaces (RISs) assist in paving the way for the evolution of conventional vehicular networks to autonomous driving. Having said that, the 3rd Generation Partnership Project (3GPP) faces numerous open challenges concerning the RIS-aided vehicle-to-everything (V2X) solutions of the near future. To tackle these challenges and to stimulate future research, this article focuses on the prospective transmission design of RIS-aided V2X communications. In particular, two V2X sidelink modes are enhanced by exploiting RISs and their variants, followed by a customized transmiss…
In this letter, we investigate the secrecy rate of an reconfigurable intelligent surface (RIS)-aided millimeter-wave (mmWave) system with hardware limitations. Compared to the RIS-aided systems in most existing works, we consider the case of the RIS-aided mmWave system with low-resolution digital-to-analog converters (LDACs). We formulate a secrecy rate maximization problem hardware constraints. Then by optimizing the RIS phase shift and the transmit beamforming to maximize the secrecy rate. Due to the nonconvexity of the problem, the formulated problem is intractable. To handle the problem, a…
The received signal strength (RSS) based technique is extensively utilized for localization in the indoor environments. Since the RSS values of neighboring locations may be similar, the localization accuracy of the RSS based technique is limited. To tackle this problem, in this paper, we propose to utilize reconfigurable intelligent surface (RIS) for the RSS based multi-user localization. As the RIS is able to customize the radio channels by adjusting the phase shifts of the signals reflected at the surface, the localization accuracy in the RIS aided scheme can be improved by choosing the prop…
The direction of arrival (DOA) estimation problem is addressed in this letter. A reconfigurable intelligent surface (RIS) aided system for the DOA estimation is proposed. Unlike traditional DOA estimation systems, a low-cost system with only one complete functional receiver is given by changing the phases of the reflected signals at the RIS elements to realize the multiple measurements. Moreover, an atomic norm-based method is proposed for the DOA estimation by exploiting the target sparsity in the spatial domain and solved by a semi-definite programming (SDP) method. Furthermore, the RIS elem…
In this paper, we study the user localization and tracking problem in the reconfigurable intelligent surface (RIS) aided multiple-input multiple-output (MIMO) system, where a multi-antenna base station (BS) and multiple RISs are deployed to assist the localization and tracking of a multi-antenna user. By establishing a probability transition model for user mobility, we develop a message-passing algorithm, termed the Bayesian user localization and tracking (BULT) algorithm, to estimate and track the user position and the angle-of-arrival (AoAs) at the user in an online fashion. We also derive B…
Reconfigurable intelligent surface (RIS) technology has recently emerged as a spectral- and cost-efficient approach for wireless communications systems. However, existing hand-engineered schemes for passive beamforming design and optimization of RIS, such as the alternating optimization (AO) approaches, require a high computational complexity, especially for multiple-input-multiple-output (MIMO) systems. To overcome this challenge, we propose a low-complexity unsupervised learning scheme, referred to as learning-phase-shift neural network (LPSNet), to efficiently find the solution to the spect…
Reconfigurable intelligent surface (RIS), a recently introduced technology for future wireless com-munication systems, enhances the spectral and energy efficiency by intelligently adjusting the propaga-tion conditions between a base station (BS) and mobile equipments (MEs). An RIS consists of manylow-cost passive reflecting elements to improve the quality of the received signal. In this paper, westudy the problem of power control at the BS for the RIS aided physical-layer broadcasting. Our goalis to minimize the transmit power at the BS by jointly designing the transmit beamforming at the BSan…
In this letter, we investigate the uplink of a reconfigurable intelligent surface (RIS)-aided millimeter-wave (mmWave) multi-user system. In the considered system, however, problems with hardware cost and power consumption arise when massive antenna arrays coupled with power-demanding analog-to-digital converters (ADCs) are employed. To account for practical hardware complexity, we consider that the access point (AP) is equipped with resolution-adaptive analog-to-digital converters (RADCs). We maximize the achievable rate under hardware constraints by jointly optimizing the ADC quantization bi…
In this thesis, we introduce the fundamental equations behind the estimation of the link budget in a communications channel, highlighting the key limitations of conventional systems. Furthermore, we investigate the use of reconfigurable intelligent surfaces as a modern method of overcoming obstruction losses, while making use of numerical methods and computational electromagnetics to understand its physical mechanism and probe its theory of operation. Additionally, a preprint on computational geometry is presented, applicable to the field of computational electromagnetics, enabling the simulat…
With the recent introduction of electromagnetic meta-surfaces and reconfigurable intelligent surfaces, a paradigm shift is currently taking place in the world of wireless communications and related industries. These new technologies have enabled the inclusion of the wireless channel as part of the optimization process. This is of great interest as we transition from 5G mobile communications towards 6G. In this paper, we explore the possibility of using a reconfigurable intelligent surface in order to disrupt the ability of an unintended receiver to geolocate the source of transmitted signals i…
This paper presents the analytic framework for evaluating the ergodic capacity (EC) of the reconfigurable intelligent surface (RIS) assisted systems. Moreover, high-signal-to-noise-ratio and high-number of reflection units (RUs) approximations for the EC are provided. Finally, the special case in which the RIS is equipped with a single RU is investigated. Our analysis is verified through respective Monte Carlo simulations, which highlight the accuracy of the proposed framework.
This paper presents an analytical pathloss model for reconfigurable intelligent surface (RIS) assisted terahertz (THz) wireless systems. Specifically, the model accommodates both the THz link and the RIS particularities. Finally, we derive a closed-form expression that returns the optimal phase shifting of each RIS reflection unit. The derived pathloss model is validated through extensive electromagnetic simulations and is expected to play a key role in the design of RIS-assisted THz wireless systems.
This paper proposes a new simultaneous terahertz (THz) information and power transfer (STIPT) system, which is assisted by reconfigurable intelligent surface (RIS) for both the information data and power transmission. We aim to maximize the information users' (IUs') data rate while guaranteeing the energy users' (EUs') and RIS's power harvesting requirements. To solve the formulated non-convex problem, the block coordinate descent (BCD) based algorithm is adopted to alternately optimize the transmit precoding of IUs, RIS's reflecting coefficients, and RIS's coordinate. The Penalty Constrained …
In this work, we investigate a reconfigurable intelligent surface (RIS) aided integrated sensing and communication scenario, where a base station (BS) communicates with multiple devices in a full-duplex mode, and senses the positions of these devices simultaneously. An RIS is assumed to be mounted on each device to enhance the reflected echoes. Meanwhile, the information of each device is passively transferred to the BS via reflection modulation. We aim to tackle the problem of joint localization and information retrieval at the BS. A grid based parametric model is constructed and the joint es…
Terahertz (THz) systems have the benefit of high bandwidth and hence are capable of supporting ultra-high data rates, albeit at the cost of high pathloss. Hence they tend to harness high-gain beamforming. Therefore a novel hybrid 3D beamformer relying on sophisticated sensor-based beam training and channel estimation is proposed for Reconfigurable Intelligent Surface (RIS) aided THz MIMO systems. A so-called array-of-subarray based THz BS architecture is adopted and the corresponding sub-RIS structure is proposed. The BS, RIS and receiver antenna arrays of the users are all uniform planar arra…
Reconfigurable intelligent surface (RIS) is a promising technique for millimeter wave (mmWave) positioning systems. In this paper, we consider multiple mobile users (MUs) positioning problem in the multiple-input multiple-output (MIMO) time-division duplex (TDD) mmWave systems aided by the RIS. We derive the expression for the space-time channel response vector (STCRV) as a novel type of fingerprint. The STCRV consists of the multipath channel characteristics, e.g., time delay and angle of arrival (AOA), which is related to the position of the MU. By using the STCRV as input, we propose a nove…
As a widely used localization and sensing technique, radars will play an important role in future wireless networks. However, the wireless channels between the radar and the targets are passively adopted by traditional radars, which limits the performance of target detection. To address this issue, we propose to use the reconfigurable intelligent surface (RIS) to improve the detection accuracy of radar systems due to its capability to customize channel conditions by adjusting its phase shifts, which is referred to as MetaRadar. In such a system, it is challenging to jointly optimize both radar…
Reconfigurable intelligent surface (RIS) is an attractive technology to improve the transmission rate of millimetre-wave (mmWave) communication systems. The previous {research} on RIS technology mainly focused on improving the transmission rate and security rate of the mmWave communication systems. Since the emergence of RIS technology creates the conditions for generating an intelligent radio environment, it also has potential advantages on improving the localization accuracy of the mmWave communication systems. Deployed on walls and objects, RISs are capable of significantly improving commun…
The conventional direction of arrival (DOA) estimation methods are performed with multiple receiving channels. In this paper, a changeling DOA estimation problem is addressed in a different scenario with only one full-functional receiving channel. A new unmanned aerial vehicle (UAV) swarm system using multiple lifted reconfigurable intelligent surface (RIS) is proposed for the DOA estimation. The UAV movement degrades the DOA estimation performance significantly, and the existing atomic norm minimization (ANM) methods cannot be used in the scenario with array perturbation. Specifically, consid…
Reconfigurable intelligent surface (RIS) has become a promising technology for enhancing the reliability of wireless communications, which is capable of reflecting the desired signals through appropriate phase shifts. However, the intended signals that impinge upon an RIS are often mixed with interfering signals, which are usually dynamic and unknown. In particular, the received signal-to-interference-plus-noise ratio (SINR) may be degraded by the signals reflected from the RISs that originate from non-intended users. To tackle this issue, we introduce the concept of intelligent spectrum learn…
By reconfiguring the propagation environment of electromagnetic waves artificially, reconfigurable intelligent surfaces (RISs) have been regarded as a promising and revolutionary hardware technology to improve the energy and spectrum efficiency of wireless networks. In this paper, we study a RIS aided multiuser multiple-input multiple-output (MIMO) wireless power transfer (WPT) system, where the transmitter is equipped with a constant-envelope analog beamformer. First, we maximize the total received power of the users by jointly optimizing the beamformer at transmitter and the phase-shifts at …
Reconfigurable intelligent surface (RIS) is one of the most promising technologies for 5G-Adv and 6G. It has the characteristics of low cost, low complexity, and easy deployment, which provides a new opportunity to develop intelligent high-speed railway communications. The typical applications of RIS-assisted smart high-speed railway communications are introduced in detail, including suppressing the Doppler shift effect, solving frequent handoff problems, overcoming high penetration loss problems, and supporting high-precision train positioning. The key technologies of RIS-assisted smart high-…
We propose a low-cost reconfigurable metasurface transmitter to implement generalized polarization-space modulation (GPSM) that has been proposed for next-generation wireless communications. Unlike conventional multiple-input multiple-output GPSM, our electromagnetically-compliant, reduced form-factor design using Barium-Strontium-Titanate film yields more than two polarization states. Full-wave simulations show our optimized design achieves 0.08-0.95 polarization conversion ratio with 5% bandwidth at 28 GHz and bit error rates comparable or better than conventional systems.
Reconfigurable intelligent surface (RIS) based communications have emerged as a new paradigm. This letter proposes a differential reflecting modulation (DRM) scheme for RIS based communication systems. In DRM, information bits are jointly carried by the activation permutations of the reflecting patterns and the phases of the transmitted signals, leading to that DRM can work without any channel state information (CSI) at the transmitter, RIS or receiver. In other words, DRM can release the intricate and resource-consuming channel estimation in the transmission process. Simulation results show t…
In this letter, we study the reconfigurable intelligent surfaces (RIS) aided full-duplex (FD) communication system. By jointly designing the active beamforming of two multi-antenna sources and passive beamforming of RIS, we aim to maximize the energy efficiency of the system, where extra self-interference cancellation power consumption in FD system is also considered. We divide the optimization problem into active and passive beamforming design subproblems, and adopt the alternative optimization framework to solve them iteratively. Dinkelbach's method is used to tackle the fractional objective…
Reconfigurable intelligent surface (RIS) has recently drawn significant attention in wireless communication technologies. However, identifying, modeling, and estimating the RIS channel in multiple-input multiple-output (MIMO) systems are considered challenging in recent studies. In this paper, a disassembled channel estimation framework for the RIS-MIMO system is proposed based on the eigenvalue decomposition (EVD) concept to separate the cascaded channel links and estimate each link separately. This estimation is based on modeling the RIS-MIMO channel as a keyhole MIMO system model. Numerical…
Optical reconfigurable intelligent surface (ORIS) is an emerging technology that can achieve reconfigurable optical propagation environments by precisely adjusting signal's reflection and shape through a large number of passive reflecting elements. In this paper, we investigate the performance of an ORIS-assisted dual-hop hybrid radio frequency (RF) and free space optics (FSO) communication system. By jointly considering the physical models of ORIS, RF channel, atmospheric turbulence, and pointing error, the closed-form solutions of the system's precise outage probability, asymptotic outage pr…
5G radio at millimeter wave (mmWave) and beyond 5G concepts at 0.1-1 THz can exploit angle and delay measurements for localization, by the virtue of increased bandwidth and large antenna arrays but are limited in terms of blockage caused by obstacles. Reconfigurable intelligent surfaces (RISs) are seen as a transformative technology that can control the physical propagation environment in which they are embedded by passively reflecting EM waves in preferred directions. Whereas such RISs have been mainly intended for communication purposes, RISs can have great benefits in terms of performance, …
A novel reconfigurable intelligent surface (RIS)-aided hybrid reflection/transmitter design is proposed for achieving information exchange in cross-media communications. In pursuit of the balance between energy efficiency and low-cost implementations, the cloud-management transmission protocol is adopted in the integrated multi-media system. Specifically, the messages of devices using heterogeneous propagation media, are firstly transmitted to the medium-matched AP, with the aid of the RIS-based dual-hop transmission. After the operation of intermediate frequency conversion, the access point (…
We investigate the benefits of integrating unmanned aerial vehicles (UAVs) with reconfigurable intelligent surface (RIS) elements to passively relay information sampled by Internet of Things devices (IoTDs) to the base station (BS). In order to maintain the freshness of relayed information, an optimization problem with the objective of minimizing the expected sum Age-of-Information (AoI) is formulated to optimize the altitude of the UAV, the communication schedule, and phases-shift of RIS elements. In the absence of prior knowledge of the activation pattern of the IoTDs, proximal policy optimi…
In this paper, we propose a novel computer vision-based approach to aid Reconfigurable Intelligent Surface (RIS) for dynamic beam tracking and then implement the corresponding prototype verification system. A camera is attached at the RIS to obtain the visual information about the surrounding environment, with which RIS identifies the desired reflected beam direction and then adjusts the reflection coefficients according to the pre-designed codebook. Compared to the conventional approaches that utilize channel estimation or beam sweeping to obtain the reflection coefficients, the proposed one …
Channel acquisition is one of the main challenges for the deployment of reconfigurable intelligent surface (RIS) aided communication systems. This is because an RIS has a large number of reflective elements, which are passive devices with no active transmitting/receiving abilities. In this paper, we study the channel estimation problem for the RIS aided multi-user millimeter-wave (mmWave) multi-input multi-output (MIMO) system. Specifically, we propose a novel channel estimation protocol for the above system to estimate the cascaded channels, which are the products of the channels from the bas…
This work demonstrates the effectiveness of a novel simultaneous transmission and reflection reconfigurable intelligent surface (STAR-RIS) in Full-Duplex (FD) aided communication system. The objective is to minimize the total transmit power by jointly designing the transmit power and the transmitting and reflecting (T&R) coefficients of the STAR-RIS. To solve the nonconvex problem, an efficient algorithm is proposed by utilizing the alternating optimization framework to iteratively optimize variables. Specifically, in each iteration, we drive the closed-form expression for the optimal power de…
We consider an uplink multi-user scenario and investigate the use of reconfigurable intelligent surfaces (RIS) to optimize spatial multiplexing performance when a linear receiver is used. We study two different formulations of the problem, namely maximizing the effective rank and maximizing the minimum singular value of the RIS-augmented channel. We employ gradient-based optimization to solve the two problems and compare the solutions in terms of the sum-rate achievable when a linear receiver is used. Our results show that the proposed criteria can be used to optimize the RIS to obtain effecti…
In the recent years, the proliferation of wireless data traffic has led the scientific community to explore the use of higher unallocated frequency bands, such as the millimeter wave and terahertz (0.1-10 THz) bands. However, they are prone to blockages from obstacles laid in the transceiver path. To address this, in this work, the use of a reconfigurable-intelligent-surface (RIS) to restore the link between a transmitter (TX) and a receiver (RX), operating in the D-band (110-170 GHz) is investigated. The system performance is evaluated in terms of pathgain and capacity considering the RIS des…
