Terahertz (THz) systems have the benefit of high bandwidth and hence are capable of supporting ultra-high data rates, albeit at the cost of high pathloss. Hence they tend to harness high-gain beamforming. Therefore a novel hybrid 3D beamformer relying on sophisticated sensor-based beam training and channel estimation is proposed for Reconfigurable Intelligent Surface (RIS) aided THz MIMO systems. A so-called array-of-subarray based THz BS architecture is adopted and the corresponding sub-RIS structure is proposed. The BS, RIS and receiver antenna arrays of the users are all uniform planar arrays (UPAs). The Ultra-wideband (UWB) sensors are integrated into the RIS and the user location information obtained by the UWB sensors is exploited for channel estimation and beamforming. Furthermore, the novel concept of a Precise Beamforming Algorithm (PBA) is proposed, which further improves the beam-forming accuracy by circumventing the performance limitations imposed by positioning errors. Moreover, the conditions of maintaining the orthogonality of the RIS-aided THz channel are derived in support of spatial multiplexing. The closed-form expressions of the near-field and far-field path-loss are also derived. Our simulation results show that the proposed scheme accurately estimates the RIS-aided THz channel and the spectral efficiency is much improved, despite its low complexity. This makes our solution eminently suitable for delay-sensitive applications.
We propose novel hybrid beamforming schemes for the terahertz (THz) wireless system where a multi-antenna base station (BS) communicates with a multi-antenna user over frequency selective fading. Here, we assume that the BS employs sub-connected hybrid beamforming and multi-carrier modulation to deliver ultra high data rate. We consider a three-dimensional wideband THz channel by incorporating the joint effect of molecular absorption, high sparsity, and multi-path fading, and consider the carrier frequency offset in multi-carrier systems. With this model, we first propose a two-stage wideband …
In this letter, we study the reconfigurable intelligent surfaces (RIS) aided full-duplex (FD) communication system. By jointly designing the active beamforming of two multi-antenna sources and passive beamforming of RIS, we aim to maximize the energy efficiency of the system, where extra self-interference cancellation power consumption in FD system is also considered. We divide the optimization problem into active and passive beamforming design subproblems, and adopt the alternative optimization framework to solve them iteratively. Dinkelbach's method is used to tackle the fractional objective…
In this work, we consider the Direction-of-Arrival (DOA) estimation problem in a low-cost architecture where only one antenna as the receiver is aided by a reconfigurable intelligent surface (RIS). We introduce the one-bit RIS as a signal reflector to enhance signal transmission in non-line-of-sight (NLOS) situations and substantially simplify the physical hardware for DOA estimation. We optimize the beamforming scheme called measurement matrix to focus the echo power on the receiver with the coarse localization information of the targets as the prior. A beamforming scheme based on the modifie…
This paper investigates the problem of resource allocation for multiuser communication networks with a reconfigurable intelligent surface (RIS)-assisted wireless transmitter. In this network, the sum transmit power of the network is minimized by controlling the phase beamforming of the RIS and transmit power of the BS. This problem is posed as a joint optimization problem of transmit power and RIS control, whose goal is to minimize the sum transmit power under signal-to-interference-plus-noise ratio (SINR) constraints of the users. To solve this problem, a dual method is proposed, where the du…
This paper proposes a new simultaneous terahertz (THz) information and power transfer (STIPT) system, which is assisted by reconfigurable intelligent surface (RIS) for both the information data and power transmission. We aim to maximize the information users' (IUs') data rate while guaranteeing the energy users' (EUs') and RIS's power harvesting requirements. To solve the formulated non-convex problem, the block coordinate descent (BCD) based algorithm is adopted to alternately optimize the transmit precoding of IUs, RIS's reflecting coefficients, and RIS's coordinate. The Penalty Constrained …
Reconfigurable intelligent surface (RIS) is an attractive technology to improve the transmission rate of millimetre-wave (mmWave) communication systems. The previous {research} on RIS technology mainly focused on improving the transmission rate and security rate of the mmWave communication systems. Since the emergence of RIS technology creates the conditions for generating an intelligent radio environment, it also has potential advantages on improving the localization accuracy of the mmWave communication systems. Deployed on walls and objects, RISs are capable of significantly improving commun…
Future wireless services, such as the metaverse require high information rate, reliability, and low latency. Multi-user wireless systems can meet such requirements by utilizing the abundant terahertz bandwidth with a massive number of antennas, creating narrow beamforming solutions. However, existing solutions lack proper modeling of channel dynamics, resulting in inaccurate beamforming solutions in high-mobility scenarios. Herein, a dynamic, semantically aware beamforming solution is proposed for the first time, utilizing novel artificial intelligence algorithms in variational causal inferenc…
Beamforming technique realized by the multiple-input-multiple-output (MIMO) antenna arrays has been widely used to compensate for the severe path loss in the millimeter wave (mmWave) bands. In 5G NR system, the beam sweeping and beam refinement are employed to find out the best beam codeword aligned to the mobile. Due to the complicated handshaking and finite resolution of the codebook, today's 5G-based beam management strategy is ineffective in various scenarios in terms of the data rate, energy consumption, and also processing latency. An aim of this article is to introduce a new type of bea…
Tri-Hybrid Beamforming Design for ISAC Systems with Reconfigurable Antennas
University of Electronic Science and Technology of China（电子科技大学）；King Abdullah University of Science and Technology（阿卜杜拉国王科技大学）；University of Manchester（曼彻斯特大学）；University College London（伦敦大学学院）
Reconfigurable Intelligent Surface (RIS) has become a popular technology to improve the capability of a THz multiuser Multi-input multi-output (MIMO) communication system. THz wave characteristics, on the other hand, restrict THz beam coverage on RIS when using a uniform planar array (UPA) antenna. In this study, we propose a dynamic RIS subarray structure to improve the performance of a THz MIMO communication system. In more details, an RIS is divided into several RIS subarrays according to the number of users. Each RIS subarray is paired with a user and only reflects beams to the correspondi…
A Fully Reconfigurable RF Vector Modulator based Wideband Phase Shifter for NextG Beamforming Phased Array in Satellite Communications (SATCOM)
University of North Dakota（北达科他大学）；Florida A&M University - Florida State University College of Engineering（佛罗里达农工大学-佛罗里达州立大学工程学院）；University of Massachusetts, Lowell（马萨诸塞大学洛厄尔分校）
This paper investigates the problem of secure energy efficiency maximization for a reconfigurable intelligent surface (RIS) assisted uplink wireless communication system, where an unmanned aerial vehicle (UAV) equipped with an RIS works as a mobile relay between the base station (BS) and a group of users. We focus on maximizing the secure energy efficiency of the system via jointly optimizing the UAV's trajectory, the RIS's phase shift, users' association and transmit power. To tackle this problem, we divide the original problem into three sub-problems, and propose an efficient iterative algor…
Reconfigurable intelligent surface (RIS) is regarded as a promising technology with great potential to boost wireless networks. Affected by the "double fading" effect, however, conventional passive RIS cannot bring considerable performance improvement when users are not close enough to RIS. Recently, active RIS is introduced to combat the double fading effect by actively amplifying incident signals with the aid of integrated reflection-type amplifiers. In order to reduce the hardware cost and energy consumption due to massive active components in the conventional fully-connected active RIS, a …
To meet the demand of supreme data rates in terabits-per-second, the next-generation mobile system needs to exploit the abundant spectrum in the millimeter-wave and terahertz bands. However, high-frequency transmission heavily relies on large-scale antenna arrays to reap high beamforming gain, used to compensate for severe propagation loss. It raises a problem of omni-directional beamforming during the phase of initial access, where a base station is required to broadcast synchronization signals and system information to all users within its coverage. This paper proposes a novel initial beamfo…
With the fifth-generation (5G) networks widely commercialized and fast deployed, the sixth-generation (6G) wireless communication is envisioned to provide competitive quality of service (QoS) in multiple aspects to global users. The critical and underlying research of the 6G is, firstly, highly dependent on the precise modeling and characterization of the wireless propagation when the spectrum is believed to expand to the terahertz (THz) domain. Moreover, future networks' power consumption and energy efficiency are critical factors to consider. In this research, based on a review of the fundam…
Reciprocal Beyond Diagonal Reconfigurable Intelligent Surface: Distributed Scattering Matrix Design and MIMO Beamforming via Fractional Programming and Manifold Optimization
School of Computer Science and Engineering, Constructor University (previously Jacobs University Bremen)（康斯坦茨大学（原雅各布斯不来梅大学）计算机科学与工程学系）；Department of Computer Science, KTH Royal Institute of Technology（瑞典皇家理工学院计算机系）
In this letter, we investigate joint application of reconfigurable intelligent surface (RIS) and vertical beamforming in cognitive radio networks (CRN). After properly modeling the network, an optimization problem is formed to jointly design the beamforming vector and tilt angle at the secondary base station (BS) as well as the phase shifts at the RIS with the objective of maximizing spectral efficiency of the secondary network. The optimization problem is non-convex; thus, we propose an efficient solution method for it. Numerical results show that adding a RIS and optimizing the radiation ori…
Future wireless communications look forward to constructing a ubiquitous intelligent information network with high data rates through cost-efficient devices. Benefiting from the tunability and programmability of metamaterials, the reconfigurable holographic surface (RHS) composed of numerous metamaterial radiation elements is developed as a promising solution to fulfill such challenging visions. The RHS is more likely to serve as an ultra-thin and lightweight surface antenna integrated with the transceiver to generate beams with desirable directions by leveraging the holographic principle. Thi…
Given its ability to control and manipulate wireless environments, reconfigurable intelligent surface (RIS), also known as intelligent reflecting surface (IRS), has emerged as a key enabler technology for the six-generation (6G) cellular networks. In the meantime, vehicular environment radio propagation is negatively influenced by a large set of objects that cause transmission distortion such as high buildings. Therefore, this work is devoted to explore the area of RIS technology integration with vehicular communications while considering the dynamic nature of such communication environment. S…
Near-optimal Reconfigurable Intelligent Surface Configuration: Blind Beamforming with Sensing
Warwick Manufacturing Group, University of Warwick（华威制造集团，华威大学）；Department of Computer Science, University of Warwick（华威大学计算机系）；Inria Centre at the University of Lille（里尔大学Inria中心）
In order to achieve terabits-per-second (Tbps) data rates in the sixth-generation (6G) mobile system, wireless communications are required to exploit the abundant spectrum in the millimeter-wave (mmWave) and terahertz (THz) bands. However, high-frequency transmission heavily relies on high beamforming gain to compensate for severe propagation loss. A beam-based system faces a barrier in the process of initial access, where a base station must broadcast synchronization signals and system information to all users within its coverage. Hence, this paper proposes a novel omnidirectional broadcastin…
Fairness-Aware Beamforming for Polarimetric ISAC Systems with Polarization-Reconfigurable Antennas
University of Electronic Science and Technology of China（电子科技大学）；Laboratory of Electromagnetic Space Cognition and Intelligent Control（电磁空间认知与智能控制实验室）；Tianfu Jiangxi Laboratory（天府江西实验室）；National Mobile Communications Research Laboratory, Southeast University（东南大学移动通信国家重点实验室）
Reconfigurable intelligent surface (RIS) can improve the communications between a source and a destination. Recently, continuous aperture RIS is proved to have better communication performance than discrete aperture RIS and has received much attention. However, the conventional continuous aperture RIS is designed to convert the incoming planar waves into the outgoing planar waves, which is not the optimal reflecting scheme when the receiver is not a planar array and is located in the near field of the RIS. In this paper, we consider two types of receivers in the radiating near field of the RIS…
In this paper, an reconfigurable intelligent surface (RIS)-aided millimeter wave (mmWave) non-orthogonal multiple access (NOMA) system is considered. In particular, we consider an RIS-aided mmWave-NOMA downlink system with a hybrid beamforming structure. To maximize the achievable sum-rate under a minimum rate constraint for the users and a minimum transmit power constraint, a joint RIS phase shifts, hybrid beamforming, and power allocation problem is formulated. To solve this non-convex optimization problem, we develop an alternating optimization algorithm. Specifically, first, the non-convex…
Wireless communication in the TeraHertz band (0.1--10 THz) is envisioned as one of the key enabling technologies for the future six generation (6G) wireless communication systems. However, very high propagation attenuations and molecular absorptions of THz frequencies often limit the signal transmission distance and coverage range. Benefited from the recent breakthrough on the reconfigurable intelligent surfaces (RIS) for realizing smart radio propagation environment, we propose a novel hybrid beamforming scheme for the multi-hop RIS-assisted communication networks to improve the coverage rang…
Terahertz (THz) communications are regarded as a pillar technology for the 6G systems, by offering multi-ten-GHz bandwidth. To overcome the huge propagation loss while reducing the hardware complexity, THz ultra-massive (UM) MIMO systems with hybrid beamforming are proposed to offer high array gain. Notably, the adjustable-phase-shifters considered in most existing hybrid beamforming studies are power-hungry and difficult to realize in the THz band. Moreover, due to the ultra-massive antennas, full channel-state-information (CSI) is challenging to obtain. To address these practical concerns, i…
Terahertz Beam Squint Mitigation via Six-Dimensional Movable Antennas
National Key Laboratory of Wireless Communications, University of Electronic Science and Technology of China（电子科技大学）；Glasgow College, University of Electronic Science and Technology of China（电子科技大学格拉斯哥学院）
We consider reconfigurable intelligent surface (RIS) aided sixth-generation (6G) terahertz (THz) communications for indoor environment in which a base station (BS) wishes to send independent messages to its serving users with the help of multiple RISs. For indoor environment, various obstacles such as pillars, walls, and other objects can result in no line-of-sight signal path between the BS and a user, which can significantly degrade performance. To overcome such limitation of indoor THz communication, we firstly optimize the placement of RISs to maximize the coverage area. Under the optimize…
Terahertz (THz) communications with a frequency band $0.1-10$ THz are envisioned as a promising solution to future high-speed wireless communication. Although with tens of gigahertz available bandwidth, THz signals suffer from severe free-spreading loss and molecular-absorption loss, which limit the wireless transmission distance. To compensate for the propagation loss, the ultra-massive multiple-input-multiple-output (UM-MIMO) can be applied to generate a high-gain directional beam by beamforming technologies. In this paper, a review of beamforming technologies for THz UM-MIMO systems is prov…
The decadal research in integrated true-time-delay arrays have seen organic growth enabling realization of wideband beamformers for large arrays with wide aperture widths. This article introduces highly reconfigurable delay elements implementable at analog or digital baseband that enables multiple SSP functions including wideband beamforming, wideband interference cancellation, and fast beam training. Details of the beam-training algorithm, system design considerations, system architecture and circuits with large delay range-to-resolution ratios are presented leveraging integrated delay compen…
