Reconfigurable intelligent surface (RIS), a recently introduced technology for future wireless com-munication systems, enhances the spectral and energy efficiency by intelligently adjusting the propaga-tion conditions between a base station (BS) and mobile equipments (MEs). An RIS consists of manylow-cost passive reflecting elements to improve the quality of the received signal. In this paper, westudy the problem of power control at the BS for the RIS aided physical-layer broadcasting. Our goalis to minimize the transmit power at the BS by jointly designing the transmit beamforming at the BSand the phase shifts of the passive elements at the RIS. Furthermore, to help validate the proposedoptimization methods, we derive lower bounds to quantify the average transmit power at the BS as afunction of the number of MEs, the number of RIS elements, and the number of antennas at the BS.The simulation results demonstrated that the average transmit power at the BS is close to the lowerbound in an RIS aided system, and is significantly lower than the average transmit power in conventionalschemes without the RIS.
An intelligent reflecting surface (IRS) is invoked for enhancing the energy harvesting performance of a simultaneous wireless information and power transfer (SWIPT) aided system. Specifically, an IRS-assisted SWIPT system is considered, where a multi-antenna aided base station (BS) communicates with several multi-antenna assisted information receivers (IRs), while guaranteeing the energy harvesting requirement of the energy receivers (ERs). To maximize the weighted sum rate (WSR) of IRs, the transmit precoding (TPC) matrices of the BS and passive phase shift matrix of the IRS should be jointly…
This paper presents a deep learning (DL) approach for estimating and detecting symbols in signals transmitted through reconfigurable intelligent surfaces (RIS). The proposed network utilizes fully connected layers to estimate channels and phase angles from a reflected signal received through an RIS. Because the proposed network can estimate and detect symbols without any pilot signaling, this method reduces the overhead required for transmission. The improvements achieved by this method are quantified in terms of the bit-error rate, outperforming traditional detectors.
By reconfiguring the propagation environment of electromagnetic waves artificially, reconfigurable intelligent surfaces (RISs) have been regarded as a promising and revolutionary hardware technology to improve the energy and spectrum efficiency of wireless networks. In this paper, we study a RIS aided multiuser multiple-input single-output (MISO) wireless power transfer (WPT) system, where the transmitter is equipped with a constant-envelope analog beamformer. We formulate a novel problem to maximize the total received power of all the users by jointly optimizing the beamformer at transmitter …
Reconfigurable intelligent surfaces (RISs) assist in paving the way for the evolution of conventional vehicular networks to autonomous driving. Having said that, the 3rd Generation Partnership Project (3GPP) faces numerous open challenges concerning the RIS-aided vehicle-to-everything (V2X) solutions of the near future. To tackle these challenges and to stimulate future research, this article focuses on the prospective transmission design of RIS-aided V2X communications. In particular, two V2X sidelink modes are enhanced by exploiting RISs and their variants, followed by a customized transmiss…
In this letter, we investigate the secrecy rate of an reconfigurable intelligent surface (RIS)-aided millimeter-wave (mmWave) system with hardware limitations. Compared to the RIS-aided systems in most existing works, we consider the case of the RIS-aided mmWave system with low-resolution digital-to-analog converters (LDACs). We formulate a secrecy rate maximization problem hardware constraints. Then by optimizing the RIS phase shift and the transmit beamforming to maximize the secrecy rate. Due to the nonconvexity of the problem, the formulated problem is intractable. To handle the problem, a…
The received signal strength (RSS) based technique is extensively utilized for localization in the indoor environments. Since the RSS values of neighboring locations may be similar, the localization accuracy of the RSS based technique is limited. To tackle this problem, in this paper, we propose to utilize reconfigurable intelligent surface (RIS) for the RSS based multi-user localization. As the RIS is able to customize the radio channels by adjusting the phase shifts of the signals reflected at the surface, the localization accuracy in the RIS aided scheme can be improved by choosing the prop…
The direction of arrival (DOA) estimation problem is addressed in this letter. A reconfigurable intelligent surface (RIS) aided system for the DOA estimation is proposed. Unlike traditional DOA estimation systems, a low-cost system with only one complete functional receiver is given by changing the phases of the reflected signals at the RIS elements to realize the multiple measurements. Moreover, an atomic norm-based method is proposed for the DOA estimation by exploiting the target sparsity in the spatial domain and solved by a semi-definite programming (SDP) method. Furthermore, the RIS elem…
As a recently proposed idea for future wireless systems, intelligent reflecting surface (IRS) can assist communications between entities which do not have high-quality direct channels in between. Specifically, an IRS comprises many low-cost passive elements, each of which reflects the incident signal by incurring a phase change so that the reflected signals add coherently at the receiver. In this paper, for an IRS-aided wireless network, we study the problem of power control at the base station (BS) for physical-layer broadcasting under quality of service (QoS) constraints at mobile users, by …
Reconfigurable intelligent surfaces (RIS) is a promising solution to build a programmable wireless environment via steering the incident signal in fully customizable ways with reconfigurable passive elements. In this paper, we consider a RIS-aided multiuser multiple-input single-output (MISO) downlink communication system. Our objective is to maximize the weighted sum-rate (WSR) of all users by joint designing the beamforming at the access point (AP) and the phase vector of the RIS elements, while both the perfect channel state information (CSI) setup and the imperfect CSI setup are investigat…
In this paper, we study the user localization and tracking problem in the reconfigurable intelligent surface (RIS) aided multiple-input multiple-output (MIMO) system, where a multi-antenna base station (BS) and multiple RISs are deployed to assist the localization and tracking of a multi-antenna user. By establishing a probability transition model for user mobility, we develop a message-passing algorithm, termed the Bayesian user localization and tracking (BULT) algorithm, to estimate and track the user position and the angle-of-arrival (AoAs) at the user in an online fashion. We also derive B…
Reconfigurable intelligent surface (RIS) technology has recently emerged as a spectral- and cost-efficient approach for wireless communications systems. However, existing hand-engineered schemes for passive beamforming design and optimization of RIS, such as the alternating optimization (AO) approaches, require a high computational complexity, especially for multiple-input-multiple-output (MIMO) systems. To overcome this challenge, we propose a low-complexity unsupervised learning scheme, referred to as learning-phase-shift neural network (LPSNet), to efficiently find the solution to the spect…
Reconfigurable intelligent surfaces (RISs) have been recently considered as one of the emerging technologies for future communication systems by leveraging the tuning capabilities of their reflecting elements. In this paper, we investigate the potential of an RIS-based architecture for uplink sensor data transmission in an ultra-reliable low-latency communication (URLLC) context. In particular, we propose an RIS-aided grant-free access scheme for an industrial control scenario, aiming to exploit diversity and achieve improved reliability performance. We consider two different resource allocati…
In this letter, we investigate the uplink of a reconfigurable intelligent surface (RIS)-aided millimeter-wave (mmWave) multi-user system. In the considered system, however, problems with hardware cost and power consumption arise when massive antenna arrays coupled with power-demanding analog-to-digital converters (ADCs) are employed. To account for practical hardware complexity, we consider that the access point (AP) is equipped with resolution-adaptive analog-to-digital converters (RADCs). We maximize the achievable rate under hardware constraints by jointly optimizing the ADC quantization bi…
This paper proposes a new simultaneous terahertz (THz) information and power transfer (STIPT) system, which is assisted by reconfigurable intelligent surface (RIS) for both the information data and power transmission. We aim to maximize the information users' (IUs') data rate while guaranteeing the energy users' (EUs') and RIS's power harvesting requirements. To solve the formulated non-convex problem, the block coordinate descent (BCD) based algorithm is adopted to alternately optimize the transmit precoding of IUs, RIS's reflecting coefficients, and RIS's coordinate. The Penalty Constrained …
In this work, we investigate a reconfigurable intelligent surface (RIS) aided integrated sensing and communication scenario, where a base station (BS) communicates with multiple devices in a full-duplex mode, and senses the positions of these devices simultaneously. An RIS is assumed to be mounted on each device to enhance the reflected echoes. Meanwhile, the information of each device is passively transferred to the BS via reflection modulation. We aim to tackle the problem of joint localization and information retrieval at the BS. A grid based parametric model is constructed and the joint es…
Terahertz (THz) systems have the benefit of high bandwidth and hence are capable of supporting ultra-high data rates, albeit at the cost of high pathloss. Hence they tend to harness high-gain beamforming. Therefore a novel hybrid 3D beamformer relying on sophisticated sensor-based beam training and channel estimation is proposed for Reconfigurable Intelligent Surface (RIS) aided THz MIMO systems. A so-called array-of-subarray based THz BS architecture is adopted and the corresponding sub-RIS structure is proposed. The BS, RIS and receiver antenna arrays of the users are all uniform planar arra…
Reconfigurable intelligent surface (RIS) is a promising technique for millimeter wave (mmWave) positioning systems. In this paper, we consider multiple mobile users (MUs) positioning problem in the multiple-input multiple-output (MIMO) time-division duplex (TDD) mmWave systems aided by the RIS. We derive the expression for the space-time channel response vector (STCRV) as a novel type of fingerprint. The STCRV consists of the multipath channel characteristics, e.g., time delay and angle of arrival (AOA), which is related to the position of the MU. By using the STCRV as input, we propose a nove…
As a widely used localization and sensing technique, radars will play an important role in future wireless networks. However, the wireless channels between the radar and the targets are passively adopted by traditional radars, which limits the performance of target detection. To address this issue, we propose to use the reconfigurable intelligent surface (RIS) to improve the detection accuracy of radar systems due to its capability to customize channel conditions by adjusting its phase shifts, which is referred to as MetaRadar. In such a system, it is challenging to jointly optimize both radar…
Reconfigurable intelligent surface (RIS) is an attractive technology to improve the transmission rate of millimetre-wave (mmWave) communication systems. The previous {research} on RIS technology mainly focused on improving the transmission rate and security rate of the mmWave communication systems. Since the emergence of RIS technology creates the conditions for generating an intelligent radio environment, it also has potential advantages on improving the localization accuracy of the mmWave communication systems. Deployed on walls and objects, RISs are capable of significantly improving commun…
The conventional direction of arrival (DOA) estimation methods are performed with multiple receiving channels. In this paper, a changeling DOA estimation problem is addressed in a different scenario with only one full-functional receiving channel. A new unmanned aerial vehicle (UAV) swarm system using multiple lifted reconfigurable intelligent surface (RIS) is proposed for the DOA estimation. The UAV movement degrades the DOA estimation performance significantly, and the existing atomic norm minimization (ANM) methods cannot be used in the scenario with array perturbation. Specifically, consid…
By reconfiguring the propagation environment of electromagnetic waves artificially, reconfigurable intelligent surfaces (RISs) have been regarded as a promising and revolutionary hardware technology to improve the energy and spectrum efficiency of wireless networks. In this paper, we study a RIS aided multiuser multiple-input multiple-output (MIMO) wireless power transfer (WPT) system, where the transmitter is equipped with a constant-envelope analog beamformer. First, we maximize the total received power of the users by jointly optimizing the beamformer at transmitter and the phase-shifts at …
A novel reconfigurable intelligent surface (RIS)-aided hybrid reflection/transmitter design is proposed for achieving information exchange in cross-media communications. In pursuit of the balance between energy efficiency and low-cost implementations, the cloud-management transmission protocol is adopted in the integrated multi-media system. Specifically, the messages of devices using heterogeneous propagation media, are firstly transmitted to the medium-matched AP, with the aid of the RIS-based dual-hop transmission. After the operation of intermediate frequency conversion, the access point (…
In this paper, we propose a novel computer vision-based approach to aid Reconfigurable Intelligent Surface (RIS) for dynamic beam tracking and then implement the corresponding prototype verification system. A camera is attached at the RIS to obtain the visual information about the surrounding environment, with which RIS identifies the desired reflected beam direction and then adjusts the reflection coefficients according to the pre-designed codebook. Compared to the conventional approaches that utilize channel estimation or beam sweeping to obtain the reflection coefficients, the proposed one …
In this letter, we focus on the hybrid precoding (HP) design for the reconfigurable intelligent surface (RIS) aided multi-user (MU) millimeter wave (mmWave) communication systems. Specifically, we aim to minimize the mean-squared-error (MSE) between the received symbols and the transmitted symbols by jointly optimizing the analog-digital HP at the base-station (BS) and the phase shifts (PSs) at the RIS, where the non-convex element-wise constant-modulus constraints for the analog precoding and the PSs are tackled by resorting to the gradient-projection (GP) method. We analytically prove the co…
We propose a low-cost reconfigurable metasurface transmitter to implement generalized polarization-space modulation (GPSM) that has been proposed for next-generation wireless communications. Unlike conventional multiple-input multiple-output GPSM, our electromagnetically-compliant, reduced form-factor design using Barium-Strontium-Titanate film yields more than two polarization states. Full-wave simulations show our optimized design achieves 0.08-0.95 polarization conversion ratio with 5% bandwidth at 28 GHz and bit error rates comparable or better than conventional systems.
Channel acquisition is one of the main challenges for the deployment of reconfigurable intelligent surface (RIS) aided communication systems. This is because an RIS has a large number of reflective elements, which are passive devices with no active transmitting/receiving abilities. In this paper, we study the channel estimation problem for the RIS aided multi-user millimeter-wave (mmWave) multi-input multi-output (MIMO) system. Specifically, we propose a novel channel estimation protocol for the above system to estimate the cascaded channels, which are the products of the channels from the bas…
Future wireless communications look forward to constructing a ubiquitous intelligent information network with high data rates through cost-efficient devices. Benefiting from the tunability and programmability of metamaterials, the reconfigurable holographic surface (RHS) composed of numerous metamaterial radiation elements is developed as a promising solution to fulfill such challenging visions. The RHS is more likely to serve as an ultra-thin and lightweight surface antenna integrated with the transceiver to generate beams with desirable directions by leveraging the holographic principle. Thi…
This paper investigates a reconfigurable intelligent surface (RIS)-aided unsourced random access (URA) scheme for the sixth-generation (6G) wireless networks with massive sporadic traffic devices. First of all, this paper proposes a novel joint active device separation (the message recovery of active device) and channel estimation architecture for the RIS-aided URA. Specifically, the RIS passive reflection is optimized before the successful device separation. Then, by associating the data sequences to multiple rank-one tensors and exploiting the angular sparsity of the RIS-BS channel, the dete…
The demands for high data rate, reliability, high energy efficiency, high spectral efficiency, and low latency communication have been increasing rapidly. For this reason, communication models that use limited resources in the best way, allow fast data transmission, and increase performance has become very important. In this work, a novel high energy and spectral efficient reconfigurable intelligent surface aided spatial media-based modulation system, called RIS-SMBM, is proposed for Rayleigh fading channels. In addition to the bits carried in the M-QAM symbol, while media-based modulation (MB…
In this paper, we propose two reconfigurable intelligent surface-aided $M$-ary frequency-modulated differential chaos shift keying (RIS-$M$-FM-DCSK) schemes. In scheme I, the RIS is regarded as a transmitter at the source to incorporate the $M$-ary phase-shift-keying ($M$-PSK) symbols into the FM chaotic signal and to reflect the resultant $M$-ary FM chaotic signal toward the destination. The information bits of the source are carried by both the positive/negative state of the FM chaotic signal and the $M$-PSK symbols. In scheme II, the RIS is treated as a relay so that both the source and rel…
In this paper, we explore optimization-based and data-driven solutions in a reconfigurable intelligent surface (RIS)-aided multi-user mobile edge computing (MEC) system, where the user equipment (UEs) can partially offload their computation tasks to the access point (AP). We aim at maximizing the total completed task-input bits (TCTB) of all UEs with limited energy budgets during a given time slot, through jointly optimizing the RIS reflecting coefficients, the AP's receive beamforming vectors, and the UEs' energy partition strategies for local computing and offloading. A three-step block coor…
Given the proliferation of wireless sensors and smart mobile devices, an explosive escalation of the volume of data is anticipated. However, restricted by their limited physical sizes and low manufacturing costs, these wireless devices tend to have limited computational capabilities and battery lives. To overcome this limitation, wireless devices may offload their computational tasks to the nearby computing nodes at the network edge in mobile edge computing (MEC). At the time of writing, the benefits of MEC systems have not been fully exploited, predominately because the computation offloading…
In the sixth-generation (6G) era, emerging large-scale computing based applications (for example processing enormous amounts of images in real-time in autonomous driving) tend to lead to excessive energy consumption for the end users, whose devices are usually energy-constrained. In this context, energy-efficiency becomes a critical challenge to be solved for harnessing these promising applications to realize 'green' 6G networks. As a remedy, reconfigurable intelligent surfaces (RIS) have been proposed for improving the energy efficiency by beneficially reconfiguring the wireless propagation e…
By activating blocked users and altering successive interference cancellation (SIC) sequences, reconfigurable intelligent surfaces (RISs) become promising for enhancing non-orthogonal multiple access (NOMA) systems. This work investigates the downlink performance of RIS-aided NOMA networks via stochastic geometry. We first introduce the unique path loss model for RIS reflecting channels. Then, we evaluate the angle distributions based on a Poisson cluster process (PCP) framework, which theoretically demonstrates that the angles of incidence and reflection are uniformly distributed. Lastly, we …
Current scene depth estimation approaches mainly rely on optical sensing, which carries privacy concerns and suffers from estimation ambiguity for distant, shiny, and transparent surfaces/objects. Reconfigurable intelligent surfaces (RISs) provide a path for employing a massive number of antennas using low-cost and energy-efficient architectures. This has the potential for realizing RIS-aided wireless sensing with high spatial resolution. In this paper, we propose to employ RIS-aided wireless sensing systems for scene depth estimation. We develop a comprehensive framework for building accurate…
A two-user downlink network aided by a reconfigurable intelligent surface is considered. The weighted sum signal to interference plus noise ratio maximization and the sum rate maximization models are presented, where the precoding vectors and the RIS matrix are jointly optimized. Since the optimization problem is non-convex and difficult, new approximation models are proposed. The upper bounds of the corresponding objective functions are derived and maximized. Two new algorithms based on the alternating direction method of multiplier are proposed. It is proved that the proposed algorithms conv…
We consider a reconfigurable intelligent surface (RIS)-aided massive multi-user multiple-input multiple-output (MIMO) communication system with transceiver hardware impairments (HWIs) and RIS phase noise. Different from the existing contributions, the phase shifts of the RIS are designed based on the long-term angle informations. Firstly, an approximate analytical expression of the uplink achievable rate is derived. Then, we use genetic algorithm (GA) to maximize the sum rate and the minimum date rate. Finally, we show that it is crucial to take HWIs into account when designing the phase shift…
A visible light communication broadcast channel is considered, in which a transmitter luminaire communicates with two legitimate receivers in the presence of an external eavesdropper. A number of trusted cooperative half-duplex relay luminaires are deployed to aid with securing the transmitted data. Transmitters are equipped with single light fixtures, containing multiple light emitting diodes, and receiving nodes are equipped with single photo-detectors, rendering the considered setting as a single-input single-output system. Transmission is amplitude-constrained to maintain operation within …
This paper investigates the performance of reconfigurable intelligent surface (RIS)-aided massive multiple-input multiple-output (MIMO) systems with direct links, and the phase shifts of the RIS are designed based on the statistical channel state information (CSI). We first derive the closed-form expression of the uplink ergodic data rate. Then, based on the derived expression, we use the genetic algorithm (GA) to solve the sum data rate maximization problem. With low-complexity maximal-ratio combination (MRC) and low-overhead statistical CSI-based scheme, we validate that the RIS can still br…
In this letter, we investigate joint application of reconfigurable intelligent surface (RIS) and vertical beamforming in cognitive radio networks (CRN). After properly modeling the network, an optimization problem is formed to jointly design the beamforming vector and tilt angle at the secondary base station (BS) as well as the phase shifts at the RIS with the objective of maximizing spectral efficiency of the secondary network. The optimization problem is non-convex; thus, we propose an efficient solution method for it. Numerical results show that adding a RIS and optimizing the radiation ori…
Reconfigurable intelligent surface (RIS)-aided networks have been investigated for the purpose of improving the system performance. However, the introduced unit modulus phase shifts and coupling characteristic bring enormous challenges to the optimization in the RIS-aided networks. Many efforts have been made to jointly optimize phase shift vector and other parameters. This article intends to survey the latest research results about the optimization in RIS-aided networks. A taxonomy is devised to categorize the existing literatures based on optimization types, phase shift form, and decoupling …
The reconfigurable intelligent surface (RIS) has arose an upsurging research interest recently due to its promising outlook in 5G-and-beyond wireless networks. With the assistance of RIS, the wireless propagation environment is no longer static and could be customized to support diverse service requirements. In this paper, we will approach the rate maximization problems in RIS-aided wireless networks by considering the beamforming and reflecting design jointly. Three representative design problems from different system settings are investigated based on a proposed unified algorithmic framework…
In this work, we consider the target detection problem in a sensing architecture where the radar is aided by a reconfigurable intelligent surface (RIS), that can be modeled as an array of sub-wavelength small reflective elements capable of imposing a tunable phase shift to the impinging waves and, ultimately, of providing the radar with an additional echo of the target. A theoretical analysis is carried out for closely- and widely-spaced (with respect to the target) radar and RIS and for different beampattern configurations, and some examples are provided to show that large gains can be achiev…
