Massive MIMO is attractive for wireless information and energy transfer due to its ability to focus energy towards desired spatial locations. In this paper, the overall power transfer efficiency (PTE) and the energy efficiency (EE) of a wireless-powered massive MIMO system is investigated where a multi-antenna base-station (BS) uses wireless energy transfer to charge single-antenna energy harvesting users on the downlink. The users may exploit the harvested energy to transmit information to the BS on the uplink. The overall system performance is analyzed while accounting for the nonlinear nature of practical energy harvesters. First, for wireless energy transfer, the PTE is characterized using a scalable model for the BS circuit power consumption. The PTE-optimal number of BS antennas and users are derived. Then, for wireless energy and information transfer, the EE performance is characterized. The EE-optimal BS transmit power is derived in terms of the key system parameters such as the number of BS antennas and the number of users. As the number of antennas becomes large, increasing the transmit power improves the energy efficiency for moderate to large number of antennas. Simulation results suggest that it is energy efficient to operate the system in the massive antenna regime.
This paper develops a novel approach to obtaining the optimal scheduling strategy in a multi-input multi-output (MIMO) multi-access channel (MAC), where each transmitter is powered by an individual energy harvesting process. Relying on the state-of-the-art convex optimization tools, the proposed approach provides a low-complexity block coordinate ascent algorithm to obtain the optimal transmission policy that maximizes the weighted sum-throughput for MIMO MAC. The proposed approach can provide the optimal benchmarks for all practical schemes in energy-harvesting powered MIMO MAC transmissions.…
We consider a full-duplex decode-and-forward system, where the wirelessly powered relay employs the time-switching protocol to receive power from the source and then transmit information to the destination. It is assumed that the relay node is equipped with two sets of antennas to enable full-duplex communications. Three different interference mitigation schemes are studied, namely, 1) optimal 2) zero-forcing and 3) maximum ratio combining/maximum ratio transmission. We develop new outage probability expressions to investigate delay-constrained transmission throughput of these schemes. Our ana…
Cell-free massive multiple-input multiple-output (MIMO) and intelligent reflecting surface (IRS) are considered as the prospective multiple antenna technologies for beyond the fifth-generation (5G) networks. Cell-free MIMO systems powered by IRSs, combining both technologies, can further improve the performance of cell-free MIMO systems at low cost and energy consumption. Prior works focused on instantaneous performance metrics and relied on alternating optimization algorithms, which impose huge computational complexity and signaling overhead. To address these challenges, we propose a novel tw…
This paper explores the potential of wireless power transfer (WPT) in massive multiple input multiple output (MIMO) aided heterogeneous networks (HetNets), where massive MIMO is applied in the macrocells, and users aim to harvest as much energy as possible and reduce the uplink path loss for enhancing their information transfer. By addressing the impact of massive MIMO on the user association, we compare and analyze two user association schemes. We adopt the linear maximal ratio transmission beam-forming for massive MIMO power transfer to recharge users. By deriving new statistical properties,…
Radio frequency (RF) energy transfer and harvesting has been intensively studied recently as a promising approach to significantly extend the lifetime of energy-constrained wireless networks. This technique has a great potential to provide relatively stable and continuous RF energy to devices wirelessly; it thus opened a new research paradigm, termed wireless-powered communication (WPC), which has raised many new research opportunities with wide applications. Among these, the design and analysis of cooperative schemes towards efficient WPC have attracted tremendous research interests nowadays.…
In this letter, we consider a large-scale multiple-input multiple-output (MIMO) system where the receiver should harvest energy from the transmitter by wireless power transfer to support its wireless information transmission. The energy beamforming in the large-scale MIMO system is utilized to address the challenging problem of long-distance wireless power transfer. Furthermore, considering the limitation of the power in such a system, this letter focuses on the maximization of the energy efficiency of information transmission (bit per Joule) while satisfying the quality-of-service (QoS) requi…
Massive multiple-inputmultiple-output (MIMO) systems, dense small-cells (SCs), and full duplex are three candidate techniques for next-generation communication systems. The cooperation of next-generation techniques could offer more benefits, e.g., SC in-band wireless backhaul in massive MIMO systems. In this paper, three strategies of SC in-band wireless backhaul in massive MIMO systems are introduced and compared, i.e., complete time-division duplex (CTDD), zero-division duplex (ZDD), and ZDD with interference rejection (ZDD-IR). Simulation results demonstrate that SC in-band wireless backhau…
In this paper, we consider a multiple-input multiple-output wireless powered communication network (MIMO-WPCN), where multiple users harvest energy from a dedicated power station in order to be able to transmit their information signals to an information receiving station. Employing a practical non-linear energy harvesting (EH) model, we propose a joint time allocation and power control scheme, which takes into account the uncertainty regarding the channel state information (CSI) and provides robustness against imperfect CSI knowledge. In particular, we formulate two non-convex optimization pr…
In this paper, we derive an asymptotic closed--form expression for the error bound on extrapolation of doubly selective mobile MIMO wireless channels. The bound shows the relationship between the prediction error and system design parameters such as bandwidth, number of antenna elements, and number of frequency and temporal pilots, thereby providing useful insights into the effects of these parameters on prediction performance. Numerical simulations show that the asymptotic bound provides a good approximation to previously derived bounds while eliminating the need for repeated computation and …
This article reviews existing related work and identifies the main challenges in the key 5G area at the intersection of waveform design and large-scale multiple antenna systems, also known as Massive MIMO. The property of self-equalization is introduced for Filter Bank Multicarrier (FBMC)-based Massive MIMO, which can reduce the number of subcarriers required by the system. It is also shown that the blind channel tracking property of FBMC can be used to address pilot contamination -- one of the main limiting factors of Massive MIMO systems. Our findings shed light into and motivate for an enti…
Information on the future state of time varying frequency selective channels can significantly enhance the effectiveness of feedback in adaptive and limited feedback MIMO-OFDM systems. This paper investigates the parametric extrapolation of wideband MIMO channels using variations of the double directional MIMO model. We propose three predictors which estimate parameters of the channel using 4D, 3D and 2D extensions of the ESPRIT algorithm and predict future states of the channel using the models. Furthermore, using the vector formulation of the Cramer Rao lower bound for functions of parameter…
We propose techniques for optimizing transmit beamforming in a full-duplex multiple-input-multiple-output (MIMO) wireless-powered communication system, which consists of two phases. In the first phase, the wireless-powered mobile station (MS) harvests energy using signals from the base station (BS), whereas in the second phase, both MS and BS communicate to each other in a full-duplex mode. When complete instantaneous channel state information (CSI) is available, the BS beamformer and the time-splitting (TS) parameter of energy harvesting are jointly optimized in order to obtain the BS-MS rate…
In this paper, we address the problem of secure wireless information and power transfer in a large-scale multiple-input multiple-output (LS-MIMO) amplify-and-forward (AF) relaying system. The advantage of LS-MIMO relay is exploited to enhance wireless security, transmission rate and energy efficiency. In particular, the challenging issues incurred by short interception distance and long transfer distance are well addressed simultaneously. Under very practical assumptions, i.e., no eavesdropper's channel state information (CSI) and imperfect legitimate channel CSI, this paper investigates the i…
In this letter, a novel wireless powered protocol is proposed to maximize the system throughput of an energy harvesting (EH) based cognitive radio network, while satisfying a minimum primary user rate requirement. For EH, we exploit both dedicated wireless power transfer from primary base station as well as ambient ones available due to wireless information transfer among primary and secondary users. Specifically, we prove convexity of the optimization problem and obtain semi-closed-form for globally optimal solution. Numerical results validate the analysis, and show an average performance imp…
This letter considers spectrum sharing between a primary multiuser multiple-input multiple-output (MIMO) wireless energy transfer (WET) system and a coexisting secondary point-to-point MIMO wireless information transmission (WIT) system, where WET generates interference to WIT and degrades its throughput performance. We show that due to the interference, the WIT system suffers from a loss of the degrees of freedom (DoF) proportional to the number of energy beams sent by the energy transmitter (ET), which, in general, needs to be larger than one in order to optimize the multiuser WET with user …
Motivated by MIMO broad-band fading channel model, in this section a comparative study is presented regarding various uncoded adaptive and non-adaptive MIMO detection algorithms with respect to BER/PER performance, and hardware complexity. All the simulations are conducted within MIMO-OFDM framework and with a packet structure similar to that of IEEE 802.11a/g standard. As the comparison results show, the RLS algorithm appears to be an affordable solution for wideband MIMO system targeting at Giga-bit wireless transmission. So MIMO can overcome huge processing power required for MIMO detection…
Ultra-dense network (UDN) has been considered as a promising candidate for future 5G network to meet the explosive data demand. To realize UDN, a reliable, Gigahertz bandwidth, and cost-effective backhaul connecting ultra-dense small-cell base stations (BSs) and macro-cell BS is prerequisite. Millimeter-wave (mmWave) can provide the potential Gbps traffic for wireless backhaul. Moreover, mmWave can be easily integrated with massive MIMO for the improved link reliability. In this article, we discuss the feasibility of mmWave massive MIMO based wireless backhaul for 5G UDN, and the benefits and …
Multiple-input multiple-output orthogonal frequency division multiplexing with index modulation (MIMO-OFDM-IM) is a novel multicarrier transmission technique which has been proposed recently as an alternative to classical MIMO-OFDM. In this scheme, OFDM with index modulation (OFDM-IM) concept is combined with MIMO transmission to take advantage of the benefits of these two techniques. In this paper, we shed light on the implementation and error performance analysis of the MIMO-OFDM-IM scheme for next generation 5G wireless networks. Maximum likelihood (ML), near-ML, simple minimum mean square …
How would a cellular network designed for high energy efficiency look like? To answer this fundamental question, we model cellular networks using stochastic geometry and optimize the energy efficiency with respect to the density of base stations, the number of antennas and users per cell, the transmit power levels, and the pilot reuse. The highest efficiency is neither achieved by a pure small-cell approach, nor by a pure massive MIMO solution. Interestingly, it is the combination of these approaches that provides the highest energy efficiency; small cells contributes by reducing the propagati…
Non-orthogonal multiple access (NOMA) and the cooperative relaying systems are two of the promising techniques to meet requirements of future wireless networks such as high spectral efficiency and wide coverage area. On the other hand, the energy efficiency has also high priority in the applications with limited energy such as sensor networks and/or internet of things (IoTs). To this end, in this paper, we propose wireless powered cooperative relaying system with NOMA thereby increasing spectral and energy efficiency. We consider three different energy harvesting (EH) protocols (i.e., power sh…
Wireless powered backscatter communications is an attractive technology for next-generation low-powered sensor networks such as the Internet of Things. However, backscattering suffers from collisions due to multiple simultaneous transmissions and a dyadic backscatter channel, which greatly attenuate the received signal at the reader. This letter deals with backscatter communications in sensor networks from a large-scale point-of-view and considers various collision resolution techniques: directional antennas, ultra-narrow band transmissions and successive interference cancellation. We derive a…
In this paper, the design of a multiple-input multiple-output (MIMO) optical wireless communication (OWC) link based on vertical cavity surface emitting laser (VCSEL) arrays is systematically carried out with the aim to support data rates in excess of 1 Tb/s for the backhaul of sixth generation (6G) indoor wireless networks. The proposed design combines direct current optical orthogonal frequency division multiplexing (DCO-OFDM) and a spatial multiplexing MIMO architecture. For such an ultra-high-speed line-of-sight (LOS) OWC link with low divergence laser beams, maintaining alignment is of hi…
As future networks aim to meet the ever-increasing requirements of high data rate applications, dense and heterogeneous networks (HetNets) will be deployed to provide better coverage and throughput. Besides the important implications for energy consumption, the trend towards densification calls for more and more wireless links to forward a massive backhaul traffic into the core network. It is critically important to take into account the presence of a wireless backhaul for the energy-efficient design of HetNets. In this paper, we provide a general framework to analyze the energy efficiency of …
We demonstrate a high capacity IF-over-fiber mobile fronthaul solution for multi-user massive MIMO 5G RAN. Using this scheme, a record aggregated radio bandwidth of 25.6 GHz was transmitted on a single optical wavelength over 40 km without fiber chromatic dispersion compensation
Considering a multiple-user multiple-input multiple-output (MIMO) channel with an eavesdropper, this letter develops a beamformer design to optimize the energy efficiency in terms of secrecy bits per Joule under secrecy quality-of-service constraints. This is a very difficult design problem with no available exact solution techniques. A path-following procedure, which iteratively improves its feasible points by using a simple quadratic program of moderate dimension, is proposed. Under any fixed computational tolerance the procedure terminates after finitely many iterations, yielding at least a…
The extreme or maximum age of information (AoI) is analytically studied for wireless communication systems. In particular, a wireless powered single-antenna source node and a receiver (connected to the power grid) equipped with multiple antennas are considered when operated under independent Rayleigh-faded channels. Via the extreme value theory and its corresponding statistical features, we demonstrate that the extreme AoI converges to the Gumbel distribution whereas its corresponding parameters are obtained in straightforward closed-form expressions. Capitalizing on this result, the risk of t…
In this paper, we introduce a mathematical approach for system-level analysis and optimization of densely deployed multiple-antenna cellular networks, where low-energy devices are capable of decoding information data and harvesting power simultaneously. The base stations are assumed to be deployed according to a Poisson point process and tools from stochastic geometry are exploited to quantify the trade-off in terms of information rate and harvested power. It is shown that multiple-antenna transmission is capable of increasing information rate and harvested power at the same time.
RF energy harvesting is a promising potential solution to provide convenient and perpetual energy supplies to low-power wireless sensor networks. In this paper, we investigate the energy harvesting performance of a wireless sensor node powered by harvesting RF energy from existing multiuser MIMO system. Specifically, we propose a random unitary beamforming (RUB) based cooperative beam selection scheme to enhance the energy harvesting performance at the sensor. Under a constant total transmission power constraint, the multiuser MIMO system tries to select a maximal number of active beams for da…
This paper studies the impact of mobility on the power consumption of wireless networks. With increasing mobility, we show that the network should dedicate a non negligible fraction of the useful rate to estimate the different degrees of freedom. In order to keep the rate constant, we quantify the increase of power required for several cases of interest. In the case of a point to point MIMO link, we calculate the minimum transmit power required for a target rate and outage probability as a function of the coherence time and the number of antennas. Interestingly, the results show that there is …
Providing consistently high wireless capacity is becoming increasingly important to support the applications required by future digital enterprises. In this paper, we propose Eigen-direction-aware ZF (EDA-ZF) with partial coordination among base stations (BSs) and distributed interference suppression as a practical approach to achieve this objective. We compare our solution with Zero Forcing (ZF), entailing neither BS coordination or inter-cell interference mitigation, and Network MIMO (NeMIMO), where full BS coordination enables centralized inter-cell interference management. We also evaluate…
This letter studies a multi-antenna wireless powered communication (WPC) system with co-channel energy and information transfer, where a wireless device (WD), powered up by wireless energy transfer (WET) from an energy transmitter (ET), communicates to an information receiver (IR) over the same frequency band. We maximize the achievable data rate from the WD to the IR by jointly optimizing the energy beamforming at the ET and the information beamforming at the WD, subject to their individual transmit power constraints. We obtain the optimal solution to this problem in closed-form, where the op…
This paper investigates the system achievable rate and optimization for the multiple-input multiple-output (MIMO)-orthogonal frequency division multiplexing (OFDM) system with an energy harvesting (EH) relay. Firstly we propose a time switchingbased relaying (TSR) protocol to enable the simultaneous information processing and energy harvesting at the relay. Then, we discuss its achievable rate performance theoretically and formulated an optimization problem to maximize the system achievable rate. As the problem is difficult to solve, we design an Augmented Lagrangian Penalty Function (ALPF) me…
The wireless communication systems has gone from different generations from SISO systems to MIMO systems. Bandwidth is one important constraint in wireless communication. In wireless communication, high data transmission rates are essential for the services like tripple play i.e. data, voice and video. At user end the capacity determines the quality of the communication systems. This paper aims to compare the different RF wireless communication systems like SISO, MISO, SIMO and MIMO systems on the capacity basis and explaining the concept as today, the wireless communication has evolved from 2…
For one isolated wireless link we take a unified look at simple beamforming (BF) as contrasted with MIMO to see how both emerge and under which conditions advantage goes to one or the other. Communication is from a high base array to a user in clutter. The channel propagation model is derived from fundamentals. The base knows the power angular spectrum, but not the channel instantiation. Eigenstates of the field spatial autocorrelation are the preferred apodizations (APODs) which are drivers of the natural modes for exciting lectric fields. Preference for MIMO or BF depends on APOD spectra whi…
Wireless-powered communications will entail short packets due to naturally small payloads, low latency requirements and/or insufficient energy resources to support longer transmissions. In this paper, a wireless-powered communication system is investigated where an energy harvesting transmitter, charged by a power beacon via wireless energy transfer, attempts to communicate with a receiver over a noisy channel. Leveraging the framework of finite-length information theory, the system performance is analyzed using metrics such as the energy supply probability at the transmitter, and the achievab…
In this paper, we consider a multiple-input-multiple-output optical wireless communication (MIMO-OWC) system suffering from log-normal fading. In this scenario, a general criterion for the design of full large-scale diversity space code (FLDSC) with the maximum likelihood (ML) detector is developed. Based on our criterion, FLDSC is attained if and only if all the entries of the space coding matrix are positive. Particularly for $2\times 2$ MIMO-OWC with unipolar pulse amplitude modulation (PAM), a closed-form linear FLDSC satisfying this criterion is attained by smartly taking advantage of som…
The recently commercialized fifth-generation (5G) wireless communication networks achieved many improvements, including air interface enhancement, spectrum expansion, and network intensification by several key technologies, such as massive multiple-input multiple-output (MIMO), millimeter-wave communications, and ultra-dense networking. Despite the deployment of 5G commercial systems, wireless communications is still facing many challenges to enable connected intelligence and a myriad of applications such as industrial Internet-of-things, autonomous systems, brain-computer interfaces, digital …
This paper maximizes the achievable throughput of a relay-assisted wirelessly powered communications system, where an energy constrained source, helped by an energy constrained relay and both powered by a dedicated power beacon (PB), communicates with a destination. Considering the time splitting approach, the source and relay first harvest energy from the PB, which is equipped with multiple antennas, and then transmits information to the destination. Simple closed-form expressions are derived for the optimal PB energy beamforming vector and time split for energy harvesting and information tra…
Reconfigurable intelligent surface (RIS) is an emerging technology to enhance wireless communication in terms of energy cost and system performance by equipping a considerable quantity of nearly passive reflecting elements. This study focuses on a downlink RIS-assisted multiple-input multiple-output (MIMO) wireless communication system that comprises three communication links of Rician channel, including base station (BS) to RIS, RIS to user, and BS to user. The objective is to design an optimal transmit covariance matrix at BS and diagonal phase-shifting matrix at RIS to maximize the achievab…
To determine the transmission strategy for joint wireless information and energy transfer (JWIET) in the MIMO interference channel (IFC), the information access point (IAP) and energy access point (EAP) require the channel state information (CSI) of their associated links to both the information-decoding (ID) mobile stations (MSs) and energy-harvesting (EH) MSs (so-called local CSI). In this paper, to reduce th e feedback overhead of MSs for the JWIET in two-user MIMO IFC, we propose a Geodesic energy beamforming scheme that requires partial CSI at the EAP. Furthermore, in the two-user MIMO IF…
In this paper, a unified linear minimum mean-square-error (LMMSE) transceiver design framework is investigated, which is suitable for a wide range of wireless systems. The unified design is based on an elegant and powerful mathematical programming technology termed as quadratic matrix programming (QMP). Based on QMP it can be observed that for different wireless systems, there are certain common characteristics which can be exploited to design LMMSE transceivers e.g., the quadratic forms. It is also discovered that evolving from a point-to-point MIMO system to various advanced wireless systems…
To meet the future demand for huge traffic volume of wireless data service, the research on the fifth generation (5G) mobile communication systems has been undertaken in recent years. It is expected that the spectral and energy efficiencies in 5G mobile communication systems should be ten-fold higher than the ones in the fourth generation (4G) mobile communication systems. Therefore, it is important to further exploit the potential of spatial multiplexing of multiple antennas. In the last twenty years, multiple-input multiple-output (MIMO) antenna techniques have been considered as the key tec…
In this paper, we provide a comprehensive system model of a wireless-powered sensor network (WPSN) based on experimental results on a real-life testbed. In the WPSN, a sensor node is wirelessly powered by the RF energy transfer from a dedicated RF power source. We define the behavior of each component comprising the WPSN and analyze the interaction between these components to set up a realistic WPSN model from the systematic point of view. Towards this, we implement a real-life and full-fledged testbed for the WPSN and conduct extensive experiments to obtain model parameters and to validate th…
There have been active research activities worldwide in developing the next-generation 5G wireless network. The 5G network is expected to support significantly large amount of mobile data traffic and huge number of wireless connections, achieve better cost- and energy-efficiency as well as quality of service (QoS) in terms of communication delay, reliability and security. To this end, the 5G wireless network should exploit potential gains in different network dimensions including super dense and heterogeneous deployment of cells and massive antenna arrays (i.e., massive multiple input multiple…
In this letter, we reconsider a popular simplified received signal power model with single stream beamforming employed by the transmitter and the receiver in the regime when the beams have high gain and narrow beamwidth. We define the correction factor as the ratio of the average actual received signal power divided by the average received signal power using the popular simplified model. We analytically quantify this factor for LOS and NLOS service and interfering links under some assumptions. The analysis along with simulations using a 3GPP compliant new radio (NR) channel model confirm the i…
In this paper, we compare two common modes of duplexing in wireless powered communication networks (WPCN); namely TDD and FDD. So far, TDD has been the most widely used duplexing technique due to its simplicity. Yet, TDD does not allow the energy transmitter to function continuously, which means to deliver the same amount of energy as that in FDD, the transmitter has to have a higher maximum transmit power. On the other hand, when regulations for power spectral density limits are not restrictive, using FDD may lead to higher throughput than that of TDD by allocating less bandwidth to energy an…
We consider simultaneous wireless information and power transfer (SWIPT) in MIMO Broadcast networks where one energy harvesting (EH) user and one information decoding (ID) user share the same time and frequency resource. In contrast to previous SWIPT systems based on the information rate, this paper addresses the problem in terms of the weighted minimum mean squared error (WMMSE) criterion. First, we formulate the WMMSE-SWIPT problem which minimizes the weighted sum-MSE of the message signal arrived at the ID user, while satisfying the requirement on the energy that can be harvested from the s…
In future sixth-generation (6G) mobile networks, the Internet-of-Everything (IoE) is expected to provide extremely massive connectivity for small battery-powered devices. Indeed, massive devices with limited energy storage capacity impose persistent energy demand hindering the lifetime of communication networks. As a remedy, wireless energy transfer (WET) is a key technology to address these critical energy supply issues. On the other hand, cell-free (CF) massive multiple-input multiple-output (MIMO) systems offer an efficient network architecture to realize the roll-out of the IoE. In this ar…
Wireless power transfer (WPT) is a promising new solution to provide convenient and perpetual energy supplies to wireless networks. In practice, WPT is implementable by various technologies such as inductive coupling, magnetic resonate coupling, and electromagnetic (EM) radiation, for short-/mid-/long-range applications, respectively. In this paper, we consider the EM or radio signal enabled WPT in particular. Since radio signals can carry energy as well as information at the same time, a unified study on simultaneous wireless information and power transfer (SWIPT) is pursued. Specifically, th…
Integrating mobile edge computing (MEC) and wireless power transfer (WPT) has been regarded as a promising technique to improve computation capabilities for self-sustainable Internet of Things (IoT) devices. This paper investigates a wireless powered multiuser MEC system, where a multi-antenna access point (AP) (integrated with an MEC server) broadcasts wireless power to charge multiple users for mobile computing. We consider a time-division multiple access (TDMA) protocol for multiuser computation offloading. Under this setup, we aim to maximize the weighted sum of the computation rates (in t…
This work considers the design of online transmission policy in a wireless-powered communication system with a given energy budget. The system design objective is to maximize the long-term throughput of the system exploiting the energy storage capability at the wireless-powered node. We formulate the design problem as a constrained Markov decision process (CMDP) problem and obtain the optimal policy of transmit power and time allocation in each fading block via the Lagrangian approach. To investigate the system performance in different scenarios, numerical simulations are conducted with variou…
Using tools from stochastic geometry, we develop a framework to model the downlink rate coverage probability of a user in a given small cell network (SCN) with massive MIMO-enabled wireless backhauls. The considered SCN is composed of a mixture of small cells that are configured in either in-band or out-of-band backhaul modes with a certain probability. The performance of the user in the considered hierarchical network is limited by several sources of interference such as the backhaul interference, small cell base station (SBS)-to-SBS interference and the SI. Moreover, due to the channel harde…
We propose the QoS-aware BS-selection and the corresponding resource-allocation schemes for downlink multi-user transmissions over the distributed multiple-input-multiple-output (MIMO) links, where multiple location-independent base-stations (BS), controlled by a central server, cooperatively transmit data to multiple mobile users. Our proposed schemes aim at minimizing the BS usages and reducing the interfering range of the distributed MIMO transmissions, while satisfying diverse statistical delay-QoS requirements for all users, which are characterized by the delay-bound violation probability…
In this paper, we consider a multiple-input-multiple-output optical wireless communication (MIMO-OWC) system in the presence of log-normal fading. In this scenario, a general criterion for the design of full-diversity space code (FDSC) with the maximum likelihood (ML) detector is developed. This criterion reveals that in a high signal-to-noise ratio (SNR) regime, MIMO-OWC offers both large-scale diversity gain, governing the exponential decaying of the error curve, and small-scale diversity gain, producing traditional power-law decaying. Particularly for a two by two MIMO-OWC system with unipo…
The performance of wireless communication is fundamentally constrained by the limited battery life of wireless devices, whose operations are frequently disrupted due to the need of manual battery replacement/recharging. The recent advance in radio frequency (RF) enabled wireless energy transfer (WET) technology provides an attractive solution named wireless powered communication (WPC), where the wireless devices are powered by dedicated wireless power transmitters to provide continuous and stable microwave energy over the air. As a key enabling technology for truly perpetual communications, WP…
This paper investigates a wireless-powered cooperative communication network consisting of a source, a destination and a multi-antenna decode-and-forward relay. We consider the relay as a wireless-powered node that has no external power supply; but it is equipped with an energy harvesting (EH) unit and a rechargeable battery such that it can harvest and accumulate energy from radio-frequency signals broadcast by the source. By fully incorporating the EH feature of the relay, we develop an opportunistic relaying protocol, termed accumulate-then-forward (ATF), for the considered WPCCN. We then a…
A wireless video transmission architecture relying on the emerging large-scale multiple-input--multiple-output (LS-MIMO) technique is proposed. Upon using the most advanced High Efficiency Video Coding (HEVC) (also known as H.265), we demonstrate that the proposed architecture invoking the low-complexity linear zero-forcing (ZF) detector and dispensing with any channel coding is capable of significantly outperforming the conventional small-scale MIMO based architecture, even if the latter employs the high-complexity optimal maximum-likelihood (ML) detector and a rate-$1/3$ recursive systematic…
In this paper, we study wireless networks where nodes have two energy sources, namely a battery and radio frequency (RF) energy harvesting circuitry. We formulate two optimization problems with different objective functions, namely maximizing the sum throughput and maximizing the minimum throughput, for enhanced fairness. Furthermore, we show the generality of the proposed system model through characterizing the conditions under which the two formulated optimization problems can be reduced to the corresponding problems of different known wireless networks, namely, conventional wireless network…
Recently, the so-called cell-free Massive MIMO architecture has been introduced, wherein a very large number of distributed access points (APs) simultaneously and jointly serve a much smaller number of mobile stations (MSs). A variant of the cell-free technique is the user-centric approach, wherein each AP just decodes the MSs that it receives with the largest power. This paper considers both the cell-free and user-centric approaches, and, using an interplay of sequential optimization and alternating optimization, derives downlink power-control algorithms aimed at maximizing either the minimum…
