Due to high density of native defects, the prototypical topological insulator (TI), Bi$_2$Se$_3$, is naturally n-type. Although Bi$_2$Se$_3$ can be converted into p-type by substituting 2+ ions for Bi, only light elements such as Ca have been so far effective as the compensation dopant. Considering that strong spin-orbit coupling (SOC) is essential for the topological surface states, a light element is undesirable as a dopant, because it weakens the strength of SOC. In this sense, Pb, which is the heaviest 2+ ion, located right next to Bi in the periodic table, is the most ideal p-type dopant for Bi$_2$Se$_3$. However, Pb-doping has so far failed to achieve p-type Bi$_2$Se$_3$ not only in thin films but also in bulk crystals. Here, by utilizing an interface engineering scheme, we have achieved the first Pb-doped p-type Bi$_2$Se$_3$ thin films. Furthermore, at heavy Pb-doping, the mobility turns out to be substantially higher than that of Ca-doped samples, indicating that Pb is a less disruptive dopant than Ca. With this SOC-preserving counter-doping scheme, it is now possible to fabricate Bi$_2$Se$_3$ samples with tunable Fermi levels without compromising their topological properties.
Thin FeRh film was extensively studied recently, and an emergent substrate- and capping-dependent interfacial ferromagnetism (FM) was widely observed in experiments. However, the voltage modulation of this interfacial ferromagnetism is barely studied, which would have profound applications in antiferromagnetic (AFM) FeRh-based magnetoelectric-random access memory (MeRAM). Using ab initio techniques, we comparatively study the interfacial ferromagnetic properties and magnetoelectric responses of ultrathin FeRh films capped by heavy transition metal Ta. We find that Ta capping reverses the phase…
A defining feature of topological insulating phases is symmetry-protected interfacial Dirac states. SnTe is a representative topological crystalline insulator, of which (110) thin films have two symmetry-unrelated valleys of interfacial states. With the help of valley-contrasting couplings of interfacial states, we design various two-dimensional topological phases in (110) SnTe thin film systems. Our first-principles calculations demonstrate that surface-state coupling strengths of two valleys independently vary with the thickness of the thin film, leading to both two-dimensional topological c…
Atomic-layer-deposited Al2O3 and HfO2 films on GaSb substrates were treated by in-situ ozone post deposition treatment (PDT). The effects of ozone PDT on the interfacial and electrical properties of Al2O3 and HfO2 gate dielectric films on GaSb substrates were investigated carefully. It is found that the dielectric quality and the interfacial properties of the Al2O3 and HfO2 films are improved by ozone PDT. After in-situ ozone PDT for 5 min, the Al2O3 and HfO2 films on GaSb substrates exhibit improved electrical and interfacial properties, such as reduced frequency dispersion, gate leakage curr…
The interfacial Dzyaloshinskii Moriya Interaction (DMI) in ultrathin magnetic thin film heterostructures provides a new approach for controlling spin textures on mesoscopic length scales. Here we investigate the dependence of the interfacial DMI constant D on a Pt wedge insertion layer in Ta_CoFeB_Pt(wedge)_MgO thin films by observing the asymmetric spin wave dispersion using Brillouin light scattering. Continuous tuning of D by more than a factor of three is realized by inserting less than one monolayer of Pt. The observations provide new insights for designing magnetic thin film heterostruct…
Band structure engineering and interfacial buffer layers have been demonstrated as effective means to tune the Fermi level in topological insulators (TI). In particular, the charge compensated compound (BixSb1-x)2Te3 (BST) plays a critical role in the molecular beam epitaxy growth of magnetic TIs. Here we introduce a strategy of exploiting epitaxial Cr2O3 as a buffer layer and amorphous Cr2O3 as a capping layer in the growth of BST films. These films exhibit carrier density lower than 1012/cm2 over a wide range of Bi contents and higher mobility than BST films directly grown on Al2O3 substrate…
Spin waves in perpendicularly-magnetized Pt/Co/AlO$_x$/Pt ultrathin films with varying Co thicknesses (0.6-1.2 nm) have been studied with Brillouin light spectroscopy in the Damon-Eshbach geometry. The measurements reveal a pronounced nonreciprocal propagation, which increases with decreasing Co thicknesses. This nonreciprocity is attributed to an interfacial Dzyaloshinskii-Moriya interaction (DMI), which is significantly stronger than asymmetries resulting from surface anisotropies for such modes. Results are consistent with an interfacial DMI constant $D_s = -1.7 \pm 0.11$ pJ/m, which favors…
This article reviews a method for calculating an equilibrium interfacial phase diagram depicting regions of stability for different interface structures as function of temperature and chemical potentials. Density functional theory (DFT) is used for interfacial energies, Monte Carlo simulations together with cluster expansions based on DFT results for obtaining configurational free energies, and CALPHAD-type modeling for describing the thermodynamic properties of the adjoining bulk phases. An explicit case, vanadium doped cemented carbides, is chosen to illustrate the progress in the research f…
The interfacial structure of SrZr$_{x}$Ti$_{1-x}$O$_3$ films grown on semiconducting Ge substrates are investigated by synchrotron X-ray diffraction and first-principles density functional theory. By systematically tuning Zr content x, the effects of bonding at the interface and epitaxial strain on the physical structure of the film can be distinguished. The interfacial perovskite layers are found to be polarized as a result of cation-anion ionic displacements perpendicular to the perovskite/semiconductor interface. We find a correlation between the observed buckling and valence band offsets a…
We studied electric field modification of magnetic properties in a Pt/Co/AlO$_x$ trilayer via magneto-optical Kerr microscopy. We observed the spontaneous formation of labyrinthine magnetic domain structure due to thermally activated domain nucleation and propagation under zero applied magnetic field. A variation of the period of the labyrinthine structure under electric field is observed as well as saturation magnetization and magnetic anisotropy variations. Using an analytical formula of the stripe equilibrium width we estimate the variation of the interfacial Dzyaloshinskii-Moriya interacti…
We have determined the depth-resolved magnetization structures of a series of highly ordered Sr$_{2}$CrReO$_{6}$ (SCRO) ferrimagnetic epitaxial films via combined studies of x-ray reflectometry, polarized neutron reflectometry and SQUID magnetometry. The SCRO films deposited directly on (LaAlO$_3$)$_{0.3}$(Sr$_2$AlTaO$_6$)$_{0.7}$ or SrTiO$_{3}$ substrates show reduced magnetization of similar width near the interfaces with the substrates, despite having different degrees of strain. When the SCRO film is deposited on a Sr$_{2}$CrNbO$_{6}$ (SCNO) double perovskite buffer layer, the width the in…
Zero field cooled spontaneous exchange bias (SEB) is observed in epitaxial La0.7Sr0.3MnO3 (LSMO):NiO self-assembled nanocomposite thin films grown on (001) SrTiO3 single crystal substrate by pulsed laser deposition. SEB is displayed by the novel asymmetry in the hysteresis loop of the composite film along with the field cooled conventional exchange bias (CEB) effect. The training effect shows that exchange bias relaxation is disorder mediated. It is revealed from DC magnetization results that such nanocomposite film divulges spin glass like behaviour, which is arising due to competing ferromag…
A detailed spectroscopic and structural characterization of ultrathin cobalt oxide films grown by O-assisted molecular beam epitaxy on a-Al2O3(0001) single crystals is reported. The experimental results show that the cobalt oxide films become progressively more disordered with increasing thickness, starting from the early stages of deposition. Low energy electron diffraction patterns suggest that the unit cell remains similar to that of a-Al2O3(0001) up to a thickness of 17 A, while at larger thicknesses a pattern identified with that of Co3O4(111) becomes visible. X-ray photoelectron spectros…
Collective spin ensembles known as skyrmion bubbles can exist in ultrathin magnetic film heterostructures and promise miniscule diameters and low-power all-electrical manipulation. The nucleation, identification and manipulation of skyrmions is of great interest, in part, because of their non-trivial topology. Here we ascertain the topology of 100 nm isolated hedgehog skyrmion bubbles and probe their response to external fields at room temperature in [ Pt \ Co (0.8 nm) \ Ir ] films. We find that structural disorder can stabilize skyrmion bubble states which exhibit creep-like domain wall motio…
By considering an interfacial layer between the electrode and the $BiFeO_{3}$($BFO$) layer, the polarization and the hysteresis behavior of $BFO$ film are simulated. It is found that the non-ferroelectric interface will increase the coercive field, and remarkably suppress the polarization of the ultrathin film under low applied fields. Due to the competition between the interfacial effect and the internal compressive stress, the maximum polarization on the P-E loop of a $BFO$ film can be independent on the film thickness under an adequate applied field.
Doping ferroelectric Hf0.5Zr0.5O2 with La is a promising route to improve endurance. However, the beneficial effect of La on the endurance of polycrystalline films may be accompanied by degradation of the retention. We have investigated the endurance - retention dilemma in La-doped epitaxial films. Compared to undoped epitaxial films, large values of polarization are obtained in a wider thickness range, whereas the coercive fields are similar, and the leakage current is substantially reduced. Compared to polycrystalline La-doped films, epitaxial La-doped films show more fatigue but there is no…
Under the correct conditions, Dzyaloshinskii-Moriya interactions (DMI) can lead to topologically protected spin textures such as skyrmions. The application of DMI for spin-based computation and memory technologies is promising and requires a detailed consideration of the role intrinsic energies have on stabilizing the diverse textures observed thus far. Here we experimentally investigate the effect of dipolar energy from interlayer coupling on the remanent spin textures found at room temperature for interfacial DMI multilayers of [ Pt \ Co \ Ir ]$_{\times N}$. The total dipolar energy is modif…
Studies of magnetization dynamics have incessantly facilitated the discovery of fundamentally novel physical phenomena, making steady headway in the development of magnetic and spintronics devices. The dynamics can be induced and detected electrically, offering new functionalities in advanced electronics at the nanoscale. However, its scattering mechanism is still disputed. Understanding the mechanism in thin films is especially important, because most spintronics devices are made from stacks of multilayers with nanometer thickness. The stacks are known to possess interfacial magnetic anisotro…
An original modification of the standard Pulse Laser Deposition (PLD) method for preparing both undoped and indium doped zinc oxide (ZnO:In) thin films at low substrate temperature is proposed. This preparation method does not demand any further post-deposition annealing treatment of the grown films. The developed method allows to grow thin films at low substrate temperature that prevents them from the considerable loss of their intrinsic electrical and optical properties. The influence of deposition parameters on the electrical and optical parameters of the undoped and the indium doped ZnO th…
We develop a model describing the electrochemical conversion of an organic semiconductor (specifically, the active material in a light-emitting electrochemical cell) from the undoped non-conducting state to the doped conducting state. The model takes into account both strongly concentration-dependent mobility and diffusion for the electronic charge carriers and the Nernst equation in the doped conducting regions. It is demonstrated that the experimentally observed doping front progression in light-emitting electrochemical cells can be accurately described with this model.
Hard-soft bilayers are analogous to prototype exchange-biased ferromagnetic -antiferromagnetic systems as the minor loop of the soft layer is biased by the hard and furthermore they offer bias layer tunability. In sputtered CoPt/Co hard-soft bilayers we demonstrate that the exchange bias field shows a linear dependence on the hard layer magnetization, while the coercivity shows a quadratic dependence. Analysis of the minor hysteresis loop features supported by Monte-Carlo simulations provide clear evidence that the coercivity of the soft layer is mainly determined by the tunable randomness of …
We have observed room temperature ferromagnetism (FM) in In$_2$O$_3$ thin films doped with either 5 at.% Mn or Fe, prepared by pulsed laser deposition (PLD) at substrate temperatures ranging from 300 to 600$\,^{\circ}{\rm C}$. The dependence of saturation magnetization on grain size was investigated for both types of In$_2$O$_3$ films. It is revealed that, for the Mn-doped films, the magnetization was largest with small grains, indicating the importance of grain boundaries. In contrast, for Fe-doped films, the largest magnetization was observed with large grains.
Vanadium doped diamond-like carbon films prepared by unbalanced magnetron sputtering have been investigated by X-ray and ultraviolet photoelectron spectroscopy measurements for the purpose of revealing electronic structures including values of work function on the surfaces. In addition to these photoelectron measurements, X-ray diffraction measurements have been performed to characterize the crystal structures.
(Li,Al)-co-doped magnesium spinel (Li$_x$Mg$_{1-2x}$Al$_{2+x}$O$_4$) is a solid lithium-ion electrolyte with potential use in all-solid-state lithium-ion batteries. Interfaces with spinel electrodes, such as Li$_y$Mn$_2$O$_4$ and Li$_{4+3z}$Ti$_5$O$_{12}$, may be lattice-matched, with potentially low interfacial resistances. Small lattice parameter differences across a lattice-matched interface are unavoidable, causing residual epitaxial strain. This strain potentially modifies lithium diffusion near the interface, contributing to interfacial resistance. Here we report a density functional the…
Interfacial mixing of elements is a well-known phenomenon found in thin film deposition. For thin-film magnetic heterostructures, interfacial compositional inhomogeneities can have drastic effects on the resulting functionalities. As such, care must be taken to characterize the compositional and magnetic properties of thin films intended for device use. Recently, ferrimagnetic Mn$_4$N thin films have drawn considerable interest due to exhibiting perpendicular magnetic anisotropy, high domain-wall mobility, and good thermal stability. In this study, we employed X-ray photoelectron spectroscopy …
The structure and chemical composition are the key parameters influencing the properties of organic thin films deposited on inorganic substrates. Such films often display structures that substantially differ from the bulk, and the substrate has a relevant influence on their polymorphism. In this work, we illuminate the role of the substrate by studying its influence for para-benzoquinone on two different substrates, Ag(111) and graphene. We employ a combination of first principles calculations and machine learning to identify the energetically most favorable structures on both substrates and s…
We investigated the origin of ferromagnetism in epitaxially grown Mn-doped Ge thin films. Using low-temperature molecular beam epitaxy, Mn-doped Ge films were successfully grown without precipitation of ferromagnetic Ge-Mn intermetallic compounds, such as Mn5Ge3. Magnetic circular dichroism measurements revealed that the epitaxially grown Mn-doped Ge films exhibited clear ferromagnetic behavior, but the Zeeman splitting observed at the critical points was not induced by the s,p-d exchange interactions. High-resolution transmission electron microscopy and energy dispersive X-ray spectroscopy an…
In this work, we demonstrate a massive intrinsic exchange bias (3 kOe) in epitaxial CoFe2O4(111) thin films deposited on Al2O3(0001) substrates. This exchange bias is indicative of intrinsic exchange or a ferromagnetic material combined with an antiferromagnet. The analysis of structure, magnetism and electronic states corroborate that there is an interfacial layer CoO between the CoFe2O4(111) thin film and the Al2O3(0001) substrate. The power-law thickness dependence of the intrinsic exchange bias verifies its interfacial origin. This work suggests interfacial engineering can be an effective …
Although rare earth nickelates (ReNiO3) exhibit abundant electronic phases and widely adjustable metal to insulator electronic transition properties, their practical electronic applications are largely impeded by their intrinsic meta stability. Apart from elevating oxygen reaction pressures, heterogeneous nucleation is expected as an alternative strategy that enables the crystallization of ReNiO3 at low meta stability. In this work, the respective roles of high oxygen pressure and heterogeneous interface in triggering ReNiO3 thin films growth at metastable state are revealed. The ReNiO3 (Re:Nd…
Doped films of organic small molecules are investigated with respect to their thermoelectric properties. A variety of hosts and dopants, for both n and p-doping, are compared. C$_{60}$ n-doped by Cr$_2$(hpp)$_4$ or o-MeO-DMBI-I are found to be the most promising material systems with a maximum of ZT$_\text{M}$ = 0.069 at T$_\text{M}$ = 40°C, assuming a doping-independent thermal conductivity due to phonon-based heat transport. This value is 16% of the current record reported for optimized devices employing the doped polymer PEDOT:PSS.
Single-phase perovskite 5 at.% Mn-doped and undoped polycrystalline BaTiO3 thin films have been grown under different oxygen partial pressures by pulsed laser deposition on platinum-coated sapphire substrates. Ferroelectricity is only observed for the Mn-doped and undoped BaTiO3 thin films grown under relatively high oxygen partial pressure. Compared to undoped BaTiO3, Mn-doped BaTiO3 reveals a low leakage current, increased dielectric loss, and a decreased dielectric constant. Ferromagnetism is seen on Mn-doped BaTiO3 thin films prepared under low oxygen partial pressure and is attributed to …
Ferromagnetism above room temperature was observed in Cr-doped hydrogenated amorphous silicon films deposited by rf magnetron-sputtering. Structure analysis reveals that films are amorphous without any detectable precipitates up to the solubility limit 16 atomic percentages of Cr. Experimental results suggest that hydrogenation has a dramatic influence on magnetic properties, electrical conductivity and carrier concentration in the thin films. Pronounced anomalous Hall effect and magnetization curve both suggest the origin of the ferromagnetism may arises from percolation of magnetic polarons.
In this paper we report the results about the synthesis and characterization of optimally doped La1-xNaxMnO3 thin films grown onto SrTiO3 (100), NdGaO3 (100) and NdGaO3 (110) for thickness ranging from 11 to 82 nm. The effect of substrate nature and orientation, film thickness and annealing procedure was investigated in order to optimize their magnetoresistance (MR). We obtained very smooth films displaying MR values greater than 70%, near to room temperature.
SrTiO$_3$ is a promising $n$-type oxide semiconductor for thermoelectric energy conversion. Epitaxial thin films of SrTiO$_3$ doped with both La and oxygen vacancies have been synthesized by pulsed laser deposition (PLD). The thermoelectric and galvanomagnetic properties of these films have been characterized at temperatures ranging from 300 K to 900 K and are typical of a doped semiconductor. Thermopower values of double-doped films are comparable to previous studies of La doped single crystals at similar carrier concentrations. The highest thermoelectric figure of merit ($ZT$) was measured t…
We study the interfacial structure, stability, and elastic properties of composite carbon films containing nanotubes. Our Monte Carlo simulations show that Van der Waals forces play a vital role in shaping up the interfacial geometry, producing a curved graphitic wall surrounding the tubes. The most stable structures are predicted to have intermediate densities, high anisotropies, and increased elastic moduli compared to pure amorphous carbon films.
In the present investigation resistivity Vs temperature measurements have been performed for solgel prepared pure and Ni doped CdO (NDO) thin films. The semiconducting behavior i.e. negative temperature coefficient of resistivity (TCR) of pure CdO thin film through-out the whole temperature range can be attributed mainly due to concentration dependent thermally activation mechanism of the carriers. The semiconductor to metal transition (SMT) for NDO thin films has been elucidated via combined effect of involved grain boundaries, ionic impurities, phonon scattering and carrier activation.
The control of the in-plane domain evolution in ferroelectric thin films is not only critical to understanding ferroelectric phenomena but also to enabling functional device fabrication. However, in-plane polarized ferroelectric thin films typically exhibit complicated multi-domain states, not desirable for optoelectronic device performance. Here we report a strategy combining interfacial symmetry engineering and anisotropic strain to design single-domain, in-plane polarized ferroelectric BaTiO$_3$ thin films. Theoretical calculations predict the key role of the BaTiO$_3$ / PrScO$_3$ (110)$_O$…
In the present work, the Mn doped benzimidazole (BMZ) thin films were prepared by simple chemical bath deposition technique. The material was directly deposited as thin film on glass substrates and the metal concentration in the solution was varied in weight percentage in order to investigate the dopant effect on the properties of thin films. Similarly, the Mn doped BMZ films were deposited in different solution temperature to study the effect of deposition temperature on the properties of thin films. The PXRD and FT-IR spectroscopy are used to study the structural and the presence of function…
Perovskite oxide based thin film gas sensors have long been considered as potential alternatives to commonly investigated binary metal oxides based sensors. BiFeO3, which is a prototype of p-type perovskite based semiconducting oxides, has recently drawn significant attention for its promising gas sensing characteristics. In the present work, the hydrogen sensing characteristics of calcium doped BiFeO3 has been reported by varying the film thickness, doping concentration, operating temperature, and test gas concentration. The films were deposited on glass substrates by sol-gel route using spin…
In this paper, we investigate three-phase eutectic growth during thin-film directional solidification of a model symmetric ternary eutectic alloy. In contrast to two-phase eutectics that have only a single possibility, $αβαβ$..., as the growth pattern, during three-phase eutectic growth infinite possibilities exist. Here, we explore the possible existence of pattern selection influenced by the change in the solid-solid interfacial energies and the diffusivities. We begin the study by estimating the undercooling vs. spacing variation for the simplest possible configurations of pattern lengths 3…
Electrodynamic properties of La-doped SrTiO3 thin films with controlled elemental vacancies have been investigated using optical spectroscopy and thermopower measurement. In particular, we observed a correlation between the polaron formation and thermoelectric properties of the transition metal oxide (TMO) thin films. With decreasing oxygen partial pressure during the film growth (P(O2)), a systematic lattice expansion was observed along with the increased elemental vacancy and carrier density, experimentally determined using optical spectroscopy. Moreover, we observed an absorption in the mid…
Hematite Fe$_2$O$_3$ seed layers are shown to constitute a pathway to prepare highly conductive transparent tin-doped indium oxide (ITO) thin films by room temperature magnetron sputtering. Conductivities of up to $σ= 3300\,{\rm S/cm}$ are observed. The improved conductivity is not restricted to the interface but related to an enhanced crystallization of the films, which proceeds in the rhombohedral phase.
We have investigated heteroepitaxial films of Sm-doped BiFeO3 with a Sm-concentration near a morphotropic phase boundary. Our high-resolution synchrotron X-ray diffraction, carried out in a temperature range of 25C to 700C, reveals substantial phase coexistence as one changes temperature to crossover from a low-temperature PbZrO3-like phase to a high-temperature orthorhombic phase. We also examine changes due to strain for films greater or less than the critical thickness for misfit dislocation formation. Particularly, we note that thicker films exhibit a substantial volume collapse associated…
A novel sol-gel route to c-axis orientated undoped and Co, Fe, Mn and V doped ZnO films is reported. Sols were prepared from a hydrated zinc acetate precursor and dimethyl formamide (DMF) solvent. Films were spin-coated on to hydrophilic sapphire substrates then dried, annealed and post-annealed, producing almost purely uniaxial ZnO crystallites and a high degree of long-range structural order. Specific orientation of hexagonal crystallites is demonstrated both perpendicular and parallel to the substrate surface. Cobalt doping resulted in the formation of columnar ZnO nanocrystals. Vanadium do…
We formulate a theoretical model of the shear failure of a thin film tethered to a rigid substrate. The interface between film and substrate is modeled as a cohesive layer with randomly fluctuating shear strength/fracture energy. We demonstrate that, on scales large compared with the film thickness, the internal shear stresses acting on the interface can be approximated by a second-order gradient of the shear displacement across the interface. The model is used to study one-dimensional shear cracks, for which we evaluate the stress-dependent probability of nucleation of a critical crack. This …
Ferroelectric materials with up-conversion luminescence (UCL) properties have potential opto-electric applications for display and sensing etc. Here, we demonstrate strong green UCL and enhanced electrical properties in Er3+-doped Na0.5Bi0.5TiO3 thin films. The thin films are prepared via using a modified chemical solution deposition method. These thin films are phase-pure and crystallized in perovskite structure. The largest remnant polarization (Pr) and highest dielectric constant are obtained from Na0.5Bi0.49Er0.01TiO3 thin films, and their values are 0.22 C/m2 and 1166, respectively. Meanw…
We observe remarkably strong room temperature ferromagnetism (~1.5 Bohr Magneton/Mn) in optically transparent Mn(II)-doped indium tin oxide (ITO) films. The nanocrystalline films with average grain size 10-22 nm and thickness 150-350 nm are prepared by sol-gel coating technique on sodalime silica glass substrate. The ferromagnetic property is, of course, weak for films deposited on pure silica glass substrate. The structural parameters of the films appear to be governing the magnetic property strongly which vary appreciably depending on the substrate. The observation of room temperature ferrom…
Atomistic simulations are used to study segregation-induced intergranular film formation in Cu-Zr and Cu-Nb alloys. While Cu-Zr forms structurally disordered or amorphous films, ordered films comprised of a second phase usually precipitate in Cu-Nb, with a critical nucleation size of ~1 nm below which the ordered phase cannot form. While the ordered film is retained at high temperature for a low energy Σ11 (113) boundary, a disordering transition is observed for a high energy Σ5 (310) boundary at low dopant concentrations. Finally, the effect of free surfaces on dopant segregation and intergra…
We use point contact Andreev reflection measurements to determine the spin polarization of the transport current in pulse laser deposited thin films of ZnO with 1% Al and with and without 2%Mn. Only films with Mn are ferromagnetic and show spin polarization of the transport current of up to 55 $\pm$ 0.5% at 4.2 K, in sharp contrast to measurements of the nonmagnetic films without Mn where the polarization is consistent with zero. Our results imply strongly that ferromagnetism in these Al doped ZnO films requires the presence of Mn.
Thin p-type Sb-doped ZnO films were grown by filtered vacuum arc deposition (FVAD), on untreated glass samples. The arc cathode was prepared by dissolving Sb into molten Zn. The deposition was performed with 200 A arc current, running for 120-240 s in 0.426 Pa oxygen pressure. The film thickness was 330-500 nm. The aotmic concentration of Sb in the films was ~1.5%, whereas the O/Zn atomic concentration ratio was ~0.7. Sb incorporation into the polycrystalline ZnO matrix was concluded from XRD analysis. The film resistivity (0.15-0.3 Ohm*m), carrier density (~10^22 m^(-3)), and carrier type, we…
Si doped ZnO thin films with Si concentrations ranging from 0.4 to 10 % have been grown by sequential pulsed laser deposition on sapphire substrates. The resistivity of the films first decreased from ~ 6.6x10-3 to 4.7x10-4 ohm-cm as the Si concentration was increased from ~ 0.4 to 2% and then it increased with further increase in Si concentration. The electron concentrations in the films were in the range from 3x1019 to 4x1020 cm-3 showing their degenerate nature. However, temperature dependent resistivity measurements in the range from 300 to 4.2 K revealed negative temperature coefficient of…
For most applications, zirconia (ZrO2) is doped with yttria. Doping leads to the stabilization of the tetragonal or cubic phase, and increased oxygen ion conductivity. Most previous surface studies of yttria-doped zirconia were plagued by impurities, however. We have studied doping of pure, 5-monolayer ZrO2 films on Rh(111) by x-ray photoelectron spectroscopy (XPS), scanning tunneling microscopy (STM), and low-energy electron diffraction (LEED). STM and LEED show that the tetragonal phase is stabilized by unexpectedly low dopant concentrations, 0.5 mol% Y2O3, even when the films are essentiall…
We present a synthesis/processing method for fabricating ferrimagnetic insulator (Bi-doped yttrium iron garnet) thin films with tunable magnetic anisotropy. Since the desired magnetic properties rely on controllable thickness and successful doping, we pay attention to the entire synthesis/processing procedure (nanopowder synthesis, nanocrystalline target preparation and pulsed laser deposition (PLD)). Atomically flat films were deposited by PLD on (111)-orientated yttrium aluminum garnet. We show a significant enhancement of perpendicular anisotropy in the films, caused by strain-induced aniso…
Organic semiconductors find increasing importance in spin transport devices due to the modulation and control of their properties through chemical synthetic versatility. The organic materials are used as interlayers between two ferromagnet (FM) electrodes in organic spin valves (OSV), as well as for magnetic spin manipulation of metal-organic complexes at the molecular level. In the latter, specifically, the substrate-induced magnetic switching in a paramagnetic molecule has been evoked extensively, but studied by delicate surface spectroscopies. Here we present evidence of the substantial mag…
We report a detailed magnetic and structural analysis of highly reduced Co doped rutile TiO2 films displaying an anomalous Hall effect (AHE). The temperature and field dependence of magnetization, and transmission electron microscopy clearly establish the presence of nano-sized superparamagnetic cobalt clusters of 8-10 nm size in the films at the interface. The co-occurrence of superparamagnetism and AHE raises questions regarding the use of the AHE as a test of the intrinsic nature of ferromagnetism in diluted magnetic semiconductors.
