We report a simple fiber-implemented technique for complete reconstruction of intensity profile and phase of ultrashort laser pulses based on processing only pulse spectrum and two self-phase modulated spectra measured after a short piece of optical fiber. Its applicability is shown on an example of a fiber optical system in the telecommunication range. A retrieval algorithm in a dispersionless approximation and with considering dispersion effects is developed. The obtained results are confirmed by independent measurements using the second-harmonic generation frequency-resolved optical gating technique and by reconstructing purposely introduced signal features. We also provide estimates demonstrating great opportunities for implementing this technique in all-waveguide optical systems ranging from optical communications to nanophotonics with femtojoule pulses as well as to mid-IR photonics, where specialty fibers with huge optical nonlinearities can be used.
Recent progresses in femtosecond ytterbium-doped fiber laser technology areopening new perspectives in strong field physics and attosecond science. Highorder harmonic generation from these systems is particularly interesting because it provides high flux beams of ultrashort extreme ultraviolet radiation. A lot of efforts have been devoted to optimize the macroscopic generation parameters. Here we investigate the possibility of enhancing the single-atom response by producing high-harmonics from the second, third and fourth harmonics of a turnkey Yb-fiber laser at 1030 nm. We show that the harmo…
We examine properties of an ultrashort laser pulse propagating through an artificial Saturable Absorber based on Nonlinear Polarization Evolution device which has been realized with Polarization Maintaining fibers only (PM NPE). We study and compare in-line and Faraday Mirror geometries showing that the latter is immune to errors in the PM NPE construction. Experimental results for the transmission measurements of the PM NPE setup for different input linear polarization angles and various input pulse powers are presented. We show that PM NPE topology is of crucial importance for controlling th…
We develop a spatiotemporal mode decomposition technique to study the mode power distribution of ultrashort pulses emerging from long spans of graded-index multimode fiber, for different input laser conditions. We find that beam mode power content in the dispersive pulse propagation regime can be described by the Bose-Einstein law, as a result of the process of power diffusion from linear and nonlinear mode coupling among nondegenerate mode groups. In the soliton regime, the output mode power distribution approaches the Rayleigh-Jeans law
We report generation of ultrashort UV pulses by soliton self-compression in kagomé-style hollow-core photonic crystal fiber filled with ambient air. Pump pulses with energy 2.6 uJ and duration 54 fs at 400 nm were compressed temporally by a factor of 5, to a duration of ~11 fs. The experimental results are supported by numerical simulations, showing that both Raman and Kerr effects play a role in the compression dynamics. The convenience of using ambient air, and the absence of glass windows that would distort the compressed pulses, makes the setup highly attractive as the basis of an efficien…
Supercontinuum (SC) generation based on ultrashort pulse compression constitutes one of the most promising technologies towards an ultra-wide bandwidth, high-brightness and spatially coherent light sources for applications such as spectroscopy and microscopy. Here, multi-octave SC generation in a gas-filled hollow-core antiresonant fiber (HC-ARF) is reported spanning from 200 nm in the deep ultraviolet (DUV) to 4000 nm in the mid-infrared (mid-IR). A measured average output power of 5 mW was obtained by pumping at the center wavelength of the first anti-resonance transmission window (2460 nm) …
While the performance of mode-locked fiber lasers has been improved significantly, the limited gain bandwidth restricts them to generate ultrashort pulses approaching a few cycles or even shorter. Here we present a novel method to achieve few cycle pulses (~5 cycles) with ultra-broad spectrum (~400 nm). To our best knowledge, this is the shortest pulse width and broadest spectrum directly generated from fiber lasers. It is noteworthy that a dramatic ultrashort pulse evolution can be stabilized in a laser oscillator by the unique nonlinear processes of a self-similar evolution as a nonlinear at…
We shape fs optical pulses and deliver them in a single spatial mode to the input of a multimode fiber. The pulse is shaped in time such that at the output of the multimode fiber an ultrashort pulse appears at a predefined focus. Our result shows how to raster scan an ultrashort pulse at the output of a stiff piece of square-core step-index multimode fiber and in this way the potential for making a nonlinear fluorescent image of the scene behind the fiber, while the connection to the multimode fiber can be established via a thin and flexible single-mode fiber. The experimental results match ou…
We introduce a small-core air-guiding photonic crystal fiber whose cladding is made of improved air-silica photonic crystal with non-circular air holes placed in triangular lattice. The fiber achieves un-disturbed bandgap guidance over 350nm wavelength range.
We demonstrate generation of 7.6 fs near-UV pulses centered at 400 nm via 8-fold soliton-effect self-compression in an Ar-filled hollow-core kagomé-style photonic crystal fiber with ultrathin core walls. Analytical calculations of the effective compression length and soliton order permit adjustment of the experimental parameters, and numerical modelling of the nonlinear pulse dynamics in the fiber accurately predict the spectro-temporal profiles of the self-compressed pulses. After compensation of phase distortion introduced by the optical elements along the beam path from the fiber to the dia…
Optical waveguide segments based on geometrically unbound photonic crystal fibers (PCF) designs could be exploited as building blocks to realize miniaturized complex devices which implement advanced photonic operations. Here, we show how to fabricate optical waveguide segments with PCF designs by direct high-resolution 3D printing and how the combination of these segments can realise complex photonic devices. We demonstrate the unprecedented precision and flexibility of our method by fabricating the first-ever fiber polarising beam splitter based on PCFs. The device was directly printed in one…
Using femtosecond laser machining, we have fabricated photonic bandgap materials that influence propagation of phonon-polaritons in ferroelectric crystals. Broadband polaritons were generated with impulsive stimulated Raman scattering (ISRS) using an ultrashort laser pulse, and the spatial and temporal evolution of the polaritons were imaged as they propagated through the fabricated structures with polariton real-space imaging. These techniques offer a new approach to optical materials design.
Broadband mid-infrared (MIR) molecular spectroscopy demands a bright and broadband light source in the molecular fingerprint region. To this end, intra-pulse difference frequency generation (IDFG) has shown excellent properties among various techniques. However, previous IDFG systems have mainly used unconventional long-wavelength 2-$μ$m ultrashort pulsed lasers. A few systems have been demonstrated with 1-$μ$m lasers, but they use bulky 100-W-class high-power Yb thin-disk lasers. In this work, we demonstrate a simple and robust approach of 1-$μ$m-pumped broadband IDFG with a conventional mode…
We present a formal analogy between the eigenvalue problem for guided scalar modes in a low-contrast photonic bandgap fiber and quasi-stationary TM modes of a two-dimensional (2D) photonic structure. Using this analogy, we numerically study the confinement losses of disordered microstructured fibers through the leakage rate of an open 2D system with high refractive index inclusions. Our results show that for large values of the disorder, the confinement losses increase. However, they also suggest that losses might be improved in strongly disordered fibers by exploring ranges of physical parame…
The efficiency of evanescent coupling between a silica optical fiber taper and a silicon photonic crystal waveguide is studied. A high reflectivity mirror on the end of the photonic crystal waveguide is used to recollect, in the backwards propagating fiber mode, the optical power that is initially coupled into the photonic crystal waveguide. An outcoupled power in the backward propagating fiber mode of 88% of the input power is measured, corresponding to a lower bound on the coupler efficiency of 94%.
Photonic crystal fibers represent one of the most active research fields in modern fiber optics. The recent advancements of topological photonics have inspired new fiber concepts and designs. Here, we demonstrate a new type of topological photonic crystal fibers based on second order photonic corner modes from the Su-Schrieffer-Heeger model. Different from previous works where the in-plane properties at $k_z=0$ have been mainly studied, we find that in the fiber configuration of $k_z>0$, a topological bandgap only exists when the propagation constant $k_z$ along the fiber axis is larger than a…
A single-mode all-silica photonic crystal fiber with an effective area of 600 square-micron and low bending loss is demonstrated. The fiber is characterized in terms of attenuation, chromatic dispersion and modal properties.
We experimentally compare the optical bandwidth of a conventional single-mode fiber (SMF) with 3 different photonic crystal fibers (PCF) all optimized for visible applications. The spectral attenuation, single-turn bend loss, and mode-field diameters (MFD) are measured and the PCF is found to have a significantly larger bandwidth than the SMF for an identical MFD. It is shown how this advantage can be utilized for realizing a larger MFD for the PCF while maintaining a bending resistant fiber.
We report on a polarization maintaining large mode area photonic crystal fiber. Unlike, previous work on polarization maintaining photonic crystal fibers, birefringence is introduced using stress applying parts. This has allowed us to realize fibers, which are both single mode at any wavelength and have a practically constant birefringence for any wavelength. The fibers presented in this work have mode field diameters from about 4 to 6.5 micron, and exhibit a typical birefringence of 1.5e-4.
We report generation of broadband low divergent supercontinuum over the entire wavelength window of 1.5 to 3.5 μm from a 2.25 meter long effective single moded photonic bandgap fiber with mode area of 1100 μm2.
We report on a highly-efficient experimental scheme for the generation of deep-ultraviolet ultrashort light pulses using four-wave mixing in gas-filled kagomé-style photonic crystal fiber. By pumping with ultrashort, few $μ$J, pulses centered at 400 nm, we generate an idler pulse at 266 nm, and amplify a seeded signal at 800 nm. We achieve remarkably high pump-to-idler energy conversion efficiencies of up to 38%. Although the pump and seed pulse durations are ~100 fs, the generated ultraviolet spectral bandwidths support sub-15 fs pulses. These can be further extended to support few-cycle puls…
We demonstrate a simple and rapid epoxy-based method for transferring photonic crystal cavities to the facets of optical fibers. Passive Si cavities were measured via fiber taper coupling as well as direct transmission from the fiber facet. Active quantum dot containing GaAs cavities showed photoluminescence that was collected both in free space and back through the original fiber. Cavities maintain a high quality factor (2000-4000) in both material systems. This new design architecture provides a practical mechanically stable platform for the integration of photonic crystal cavities with macr…
We analyze the guiding problem in a realistic photonic crystal fiber using a novel full-vector modal technique, a biorthogonal modal method based on the nonselfadjoint character of the electromagnetic propagation in a fiber. Dispersion curves of guided modes for different fiber structural parameters are calculated along with the 2D transverse intensity distribution of the fundamental mode. Our results match those achieved in recent experiments, where the feasibility of this type of fiber was shown.
We study the class of endlessly single-mode all-silica photonic crystal fibers with a triangular air-hole cladding. We consider the sensibility to longitudinal nonuniformities and the consequences and limitations for realizing low-loss large-mode area photonic crystal fibers. We also discuss the dominating scattering mechanism and experimentally we confirm that both macro and micro-bending can be the limiting factor.
The field of attosecond physics has seen an almost explosive growth since the early 2000's and represents by now an increasing fraction of contributions to the bi-annual series of International Conferences of Photonic, Electronic, and Atomic Collisions (ICPEAC). The latter is anything but a coincidence as many of the underlying concepts of electronic and photonic dynamics are closely intertwined with atomic-scale collision processes. We illustrate this fruitful connection and its implications with the help of a few prototypical examples of current topical interest.
The field energy distributions and effective mode areas of silica-based photonic bandgap fibers with a honeycomb airhole structure in the cladding and an extra airhole defining the core are investigated. We present a generalization of the common effective area definition, suitable for the problem at hand, and compare the results for the photonic bandgap fibers with those of index-guiding microstructured fibers. While the majority of the field energy in the honeycomb photonic bandgap fibers is found to reside in the silica, a substantial fraction (up to ~30%) can be located in the airholes. Thi…
We consider chromatic dispersion of capillary tubes and photonic crystal fibers infiltrated with liquid crystals. A perturbative scheme for inclusion of material dispersion of both liquid crystal and the surrounding waveguide material is derived. The method is used to calculate the chromatic dispersion at different temperatures.
Results from the calculation of the basic characteristics of the photonic crystal fiber with two rings of holes are presented by the approach which takes into account the exact distribution of the refractive index over the cross section of the photonic crystal fiber. Formulae are theoretically derived for the calculation of holes with arbitrary shapes by dividing the material within them into rotated at different angles rectangles. Keywords: photonic crystal fibre, Galerkin method, a set of sine functions, local coordinate systems.
In the paper, we propose the new technology for mass production of the photonic crystal devices and all-optical integrated circuits. We carry out the brief analysis of positive and negative sides paying attention to recent advances in silicon fibers fabrication which is crucial moment in the proposed technology.
Quasi error-free 10 Gbit/s data transmission is demonstrated over a novel type of 50 micron core diameter photonic crystal fiber with as much as 100 m length. Combined with 850$ nm VCSEL sources, this fiber is an attractive alternative to graded-index multi-mode fibers for datacom applications. A comparison to numerical simulations suggests that the high bit-rate may be partly explained by inter-modal diffusion.
We demonstrate experimentally that random phase modulation of an erbium-doped fiber ring-laser by an intra-cavity electro-optic phase modulator did not inhibit ultrashort-pulse operation. Stable and self-starting ultrashort-pulse operation with a single pulse circulating in the cavity was achieved even when the phase modulator was driven with random sequences sufficiently fast and strong to render the laser cavity modeless, in the sense that heterodyning of the laser output did not show any spectral lines corresponding to a mode spectrum. No significant change in measured pulse characteristics…
For the first time, we demonstrated that a hyper-broadband from 2μm to 10μm can be generated with a high spectral flatness by using a ~4 um pump and an As2Se3 photonic crystal fiber. The broad and flat dispersion profile and the low guiding loss of the endlessly single-mode As2Se3 photonic crystal fibers combining with the high nonlinearity and wide mid-infrared transparent window of As2Se3 chalcogenide glass are essential for this high performance mid-infrared laser source.
Multimode optical fibers has emerged as the platform that will bridge the gap between nonlinear optics in bulk media and in single-mode fibers. However, the understanding of the transition between these two research fields still remains incomplete despite numerous investigations of intermodal nonlinear phenomena and spatiotemporal coupling. Some of the striking phenomena observed in bulk media with ultrashort and ultra-intense pulses (i.e., conical emission, harmonic generation and light bullets) require a deeper insight to be possibly unveiled in multimode fibers. Here we generalize the conce…
We build ring resonators to assess the potentialities of Kagome Hollow-Core Photonic Crystal Fibers for future applications to resonant rotation sensing. The large mode diameter of Kagome fibers permits to reduce the free space fiber-to-fiber coupling losses, leading to cavities with finesses of about 30 for a diameter equal to 15 cm. Resonance linewidths of 3.2~MHz with contrasts as large as 89\% are obtained. Comparison with 7-cell photonic band gap (PBG) fiber leads to better finesse and contrast with Kagome fiber. Resonators based on such fibers are compatible with the angular random walk …
Structured light have made deep impacts on modern biotechnology and clinical practice, with numerous optical systems and lasers currently being used in medicine to treat disease. We demonstrate a new concept of fiber-based optical hook scalpel. The subwavelength photonic hook is obtained in the vicinity of a shaped fiber tip with asymmetric radiation. A 1550 nm continuous-wave source, commonly used for medical imaging, has been required. Photonic hook with a lateral feature size less than the half-wavelength is achieved using a hemispherical shaped fiber tip with metallic mask. This breakthrou…
Optical fiber tapers are used to collect photoluminescence emission at ~1.5 um from photonic crystal cavities fabricated in erbium doped silicon nitride on silicon. Photoluminescence collection via fiber taper is enhanced 2.5 times relative to free space, with a total taper collection efficiency of 53%. By varying the fiber taper offset from the cavity, a broad tuning range of coupling strength is obtained. This material system combined with fiber taper collection is promising for building on-chip optical amplifiers.
We demonstrate experimentally that the spectral broadening of CW supercontinuum can be controlled by using photonic crystal fibers with two zero-dispersion wavelengths pumped by an Yb fiber laser at 1064 nm. The spectrum is bounded by two dispersive waves whose spectral location depends on the two zero-dispersion wavelengths of the fiber. The bandwidth of the generated spectrum and the spectral power density may thus be tailored for particular applications, such as high-resolution optical coherence tomography or optical spectroscopy.
Transient fully reconfigurable photonic circuits can be introduced at the optical fiber surface with subangstrom precision. A building block of these circuits, a 0.7 angstrom-precise nano-bottle resonator, is experimentally created by local heating, translated, and annihilated.
We present highly sensitive refractometers based on a long-period grating in a large mode area PCF. The maximum sensitivity is 1500 nm/RIU at a refractive index of 1.33, the highest reported for any fiber grating. The minimal detectable index change is $2\times 10^{-5}$. The high sensitivity is obtained by infiltrating the sample into the holes of the photonic crystal fiber to give a strong interaction between the sample and the probing field.
The possibility of soliton self-compression of ultrashort laser pulses down to the few-cycle regime in photonic crystal fibers is numerically investigated. We show that efficient sub-two-cycle temporal compression of nanojoule-level 800 nm pulses can be achieved by employing short (typically 5-mm-long) commercially available photonic crystal fibers and pulse durations of around 100 fs, regardless of initial linear chirp, and without the need of additional dispersion compensation techniques. We envisage applications in a new generation of compact and efficient sub-two cycle laser pulse sources.
We propose a new method for mass production of the photonic crystal devices on the basis of widely-known and well-developed technology such as microstructured optical fibers. In this paper, we investigate the optical properties of side-excited microstructured optical fiber and discuss the conditions for utilization such a structure as a planar photonic crystal device, namely, the high-quality resonance filter.
In this paper we propose a new hypothesis of out of plane band gap formation in all solid photonic band gap (PBG) fibers. At first, one considers the process of the core modes formation as a result of excitation of continuous mode spectrum of single dielectric rod of the cladding. It is shown that the core modes can be considered as transverse resonance of a set of the radiation modes decoupled from the continuum provided that the phase matching condition for the propagation constants are fulfilled. An analogy between the core mode formation in all solid PBG fibers and formation of bound state…
In a recent paper, Subbaraman et al report a theoretical and numerical study of highly dispersive pure silica photonic crystal fiber supporting group-velocity dispersion exceeding -2*10^4 ps/nm/km. This comment argues that the authors only consider one out of the two sides of the same coin, by not taking the corresponding beating length into account.
Based on a recent formulation of the V-parameter of a photonic crystal fiber we provide numerically based empirical expressions for this quantity only dependent on the two structural parameters - the air hole diameter and the hole-to-hole center spacing. Based on the unique relation between the V-parameter and the equivalent mode field radius we identify how the parameter space for these fibers is restricted in order for the fibers to remain single mode while still having a guided mode confined to the core region.
We study photonic crystal fibers and ring resonators with topological features induced by Aubry- Andre-Harper modulations of the cladding. We find non trivial gaps and edge states at the interface between regions with different Chern numbers. We calculate the field profile and eigenvalue dispersion by an exact recursive approach. Compared with conventional circular resonators and fibers, the proposed structure features topological protection and hence robustness against symmetry-preserving local perturbations that do not close the gap. These topological photonic crystal fibers sustain strong f…
The waveguiding properties of two silica-based airguiding photonic bandgap fiber designs are investigated with special emphasis on material effects. The nonlinear coefficients are found to be 1-2 orders of magnitude smaller than those obtained in index-guiding microstructured fibers with large mode areas. The material dispersion of silica makes a significant contribution to the total chromatic dispersion although less than 10% of the field energy is located in the silica regions of the fibers. These findings suggest that dispersion engineering through the choice of base material may be a possi…
Flying particle sensors in hollow-core photonic crystal fibers require accurate localization of the optically trapped microparticles. We report position measurement to micrometer-resolution, using optical frequency domain reflectometry, of two 1.65-$μ$m-diameter polystyrene particles.
We investigate resonant nonlinear optical interactions and demonstrate induced transparency in acetylene molecules in a hollow-core photonic band-gap fiber at 1.5$μ$m. The induced spectral transmission window is used to demonstrate slow-light effects, and we show that the observed broadening of the spectral features is due to collisions of the molecules with the inner walls of the fiber core. Our results illustrate that such fibers can be used to facilitate strong coherent light-matter interactions even when the optical response of the individual molecules is weak.
We propose an optical trapping technique in which a fundamental soliton traps an ultrashort small amplitude radiation in a symmetric hollow-core photonic crystal fiber filled with a noble gas, preventing its dispersion. The system is Raman- and plasma-free. Trapping is due to the cross phase modulation effect between the two pulses. The trapped radiation inside the soliton-induced potential will oscillate periodically due to the shock effect, similar to the motion of a mechanical pendulum.
We consider large-mode area photonic crystal fibers for visible applications where micro-deformation induced attenuation becomes a potential problem when the effective area A_eff is sufficiently large compared to lambda^2. We argue how a slight increase in fiber diameter D can be used in screening the high-frequency components of the micro-deformation spectrum mechanically and we confirm this experimentally for both 15 and 20 micron core fibers. For typical bending-radii (R~16 cm) the operating band-width increases by ~3-400 nm to the low-wavelength side.
We demonstrate an amplitude-based micro-displacement sensor that uses a plastic photonic bandgap Bragg fiber with one end coated with a silver layer. The reflection intensity of the Bragg fiber is characterized in response to different displacements (or bending curvatures). We note that the Bragg reflector of the fiber acts as an efficient mode stripper for the wavelengths near the edge of the fiber bandgap, which makes the sensor extremely sensitive to bending or displacements at these wavelengths. Besides, by comparison of the Bragg fiber sensor to a sensor based on a regular multimode fiber…
We demonstrate analytically and numerically that a subwavelength-core dielectric photonic nanowire embedded in a properly designed photonic crystal fiber cladding shows evidence of a previously unknown kind of nonlinearity (the magnitude of which is strongly dependent on the waveguide parameters) which acts on solitons so as to considerably reduce their Raman self-frequency shift. An explanation of the phenomenon in terms of indirect pulse negative chirping and broadening is given by using the moment method. Our conclusions are supported by detailed numerical simulations.
We address the long-standing unresolved problem concerning the V-parameter in a photonic crystal fiber (PCF). Formulate the parameter appropriate for a core-defect in a periodic structure we argue that the multi-mode cut-off occurs at a wavelength lambda* which satisfies V_PCF(lambda*)=pi. Comparing to numerics and recent cut-off calculations we confirm this result.
We have investigated the interaction between a strong soliton and a weak probe with certain configurations that allow optical trapping in gas-filled hollow-core photonic crystal fibers in the presence of the shock effect. We have shown theoretically and numerically that the shock term can lead to an unbroken parity-time $ \left(\mathcal{PT}\right) $ symmetry potential in these kinds of fibers. Reciprocity breaking, a remarkable feature of the $ \mathcal{PT} $ symmetry, is also demonstrated numerically. Our results will open different configurations and avenues for observing $ \mathcal{PT} $-sy…
We show that point defects in two-dimensional photonic crystals can support bound states in the continuum (BICs). The mechanism of confinement is a symmetry mismatch between the defect mode and the Bloch modes of the photonic crystal. These BICs occur in the absence of bandgaps and therefore provide an alternative mechanism to confine light. Furthermore, we show that such BICs can propagate in a fiber geometry and exhibit arbitrarily small group velocity which could serve as a platform for enhancing non-linear effects and light-matter interactions in structured fibers.
