We report evidence of a non-adiabatic Kohn anomaly in boron-doped diamond, using a joint theoretical and experimental analysis of the phonon dispersion relations. We demonstrate that standard calculations of phonons using density functional perturbation theory are unable to reproduce the dispersion relations of the high-energy phonons measured by high-resolution inelastic x-ray scattering. On the contrary, by taking into account non-adiabatic effects within a many-body field-theoretic framework, we obtain excellent agreement with our experimental data. This result indicates a breakdown of the Born-Oppenheimer approximation in the phonon dispersion relations of boron-doped diamond.
Isolated hydrogen and hydrogen pairs in bulk diamond matrix have been studied using density functional theory calculations. The electronic structure and stability of isolated and paired hydrogen defects are investigated at different possible lattice sites in pure diamond and boron doped diamond. Calculations revealed that isolated hydrogen defect is stable at bond center sites for pure diamond and bond center puckered site for boron doped diamond. In case of hydrogen pairs, H2 defect (one hydrogen at bond center and second at anti-bonding site) is stable for pure diamond, while for boron doped…
Kim et al. have reported a dependence of the infrared excitation energies of boron acceptors in diamond on the isotopic mass of the carbon atoms. We show that this change can be quantitatively interpreted as induced by a change in the hole effective mass. Keywords: A. Diamond, A. Stable isotopes, D. Acceptor binding energies, D. Effective masses of holes
Using angle-resolved photoelectron spectroscopy, we compare the electronic band structure of an ultrathin (1.8 nm) δ-layer of boron-doped diamond with a bulk-like boron doped diamond film (3 μm). Surprisingly, the measurements indicate that except for a small change in the effective mass, there is no significant difference between the electronic structure of these samples, irrespective of their physical dimensionality. While this suggests that, at the current time, it is not possible to fabricate boron-doped diamond structures with quantum properties, it also means that nanoscale doped diamond…
The boron-doped single crystal diamond films were grown homoepitaxially on synthetic (100) oriented Type Ib diamond substrates using a Microwave Plasma Chemical Vapor Deposition (MPCVD) technique. Raman spectrum showed a few additional bands at the lower wavenumber regions along with the zone center optical phonon mode for diamond. The change in the peak profile of the zone center optical phonon mode and its downshift were observed with the increasing boron content in the film. A modification in surface morphology of the film with increasing boron content had been observed by atomic force micr…
This work demonstrates the effectiveness of the high-pressure method for the production of graphite and diamond with a high degree of boron doping using adamantanecarborane mixture as a precursor. At 8 GPa and $1700 ^{o}C$, graphite is obtained from adamantane $C_{10}H_{16}$, whereas microcrystals of boron-doped diamond (2÷2.5 at.% of boron) are synthesized from a mixture of adamantane and ortho-carborane $C_{2}B_{10}H_{12}$ (atomic ratio B:C = 5:95). This result shows convincingly the catalytical activity of boron in the synthesis of diamond under high pressure. At pressures lower than 7 GPa,…
Boron-doped diamond undergoes an insulator-metal transition at some critical value (around 2.21 at %) of the dopand concentration. Here, we report a simple method for the calculation of its bulk modulus, based on the thermodynamical model, by Varotsos and Alexopoulos, that has been originally suggested for the interconnection between the defect formation parameters in solids and bulk properties. The results obtained at the doping level of 2.6 at %, which was later improved at the level 0.5 at %, are in agreement with the experimental values.
The light scattering properties of superconducting (Tc=3.8 K) heavily boron doped nanocrystalline diamond has been investigated by Raman spectroscopy using visible excitations. Fano type interference of the zone-center phonon line and the electronic continuum was identified. Lineshape analysis reveals Fano lineshapes with a significant asymmetry (q=-2). An anomalous wavelength dependence and small value of the Raman scattering amplitude is observed in agreement with previous studies.
Boron-doped single crystal diamond films were grown homoepitaxially on synthetic (100) Type Ib diamond substrates using microwave plasma assisted chemical vapor deposition. A modification in surface morphology of the film with increasing boron concentration in the plasma has been observed using atomic force microscopy. Use of nitrogen during boron doping has been found to improve the surface morphology and the growth rate of films but it lowers the electrical conductivity of the film. The Raman spectra indicated a zone center optical phonon mode along with a few additional bands at the lower w…
Isotopic substitution of boron and carbon is applied for the identification of the vibrational modes of heavily boron-doped diamond synthesized by high-pressure high-temperature technique. None of the bands in the Raman spectra are shifting upon ^{10}B-substitution, whereas shifts to lower frequency are observed for all bands upon ^{13}C-substitution as compared to a sample with natural isotope abundancies. These isotopic substitution experiments exclude the hypothesis of boron dimer related normal modes and strongly support the assignment of the previously studied "500 cm^{-1}" and "1230 cm^{…
Both boron nitride (BN) and carbon (C) have sp, sp2 and sp3 hybridization modes, and thus resulting in a variety of BN and C polymorphs with similar structures, such as hexagonal BN (hBN) and graphite, cubic BN (cBN) and diamond. Here, five types of BN polymorph structures were proposed theoretically, inspired by the graphite-diamond hybrid structures discovered in recent experiment. These BN polymorphs with graphite-diamond hybrid structures possessed excellent mechanical properties with combined high hardness and high ductility, and also exhibited various electronic properties such as semi-c…
The density of states and the band diagrams were computed for diamond, cubic boron nitrde (cBN), and hexagonal boron nitride (hBN) using a Korringa-Kohn-Rostoker (KKR) scheme to investigate the shift of the Fermi level by impurity-atom doping below 10 at.%. The dopant atoms were B and N for diamond, Be, Si, and C for cBN, and Be and C for hBN. It was found that the Fermi level was located at the valence band maximum or the conduction band minimum in the following seven cases: (i) the B concentration was 0.3 at.% in B-doped diamond, (ii) the N concentration was 0.4 at.% in N-doped diamond, (iii…
Optical centers in cubic boron nitride and diamond: remarkable similarities
Central European Institute of Technology, Brno University of Technology（中欧技术研究所，布尔诺理工大学）；Jilin Diamond Technology Research & Development（吉林金刚石技术研发有限公司）
With the best overall electronic and thermal properties, single crystal diamond (SCD) is the extreme wide bandgap material that is expected to revolutionize power electronics and radio-frequency electronics in the future. However, turning SCD into useful semiconductors requires overcoming doping challenges, as conventional substitutional doping techniques, such as thermal diffusion and ion implantation, are not easily applicable to SCD. Here we report a simple and easily accessible doping strategy demonstrating that electrically activated, substitutional doping in SCD without inducing graphiti…
Boron-doped diamond granular thin films are known to exhibit superconductivity with an optimal critical temperature of Tc = 7.2K. Here we report the measured complex surface impedance of Boron-doped diamond films in the microwave frequency range using a resonant technique. Experimentally measured inductance values are in good agreement with estimates obtained from the normal state sheet resistance of the material. The magnetic penetration depth temperature dependence is consistent with that of a fully-gapped s-wave superconductor. Boron-doped diamond films should find application where high ki…
The electronic structure, lattice dynamics, and electron-phonon coupling of the boron-doped diamond are investigated using the density functional supercell method. Our results indicate the boron-doped diamond is a phonon mediated superconductor, con rming previous theoretical conclusions deduced from the calculations employing the virtual crystal approximation. We show that the optical phonon modes involving B vibrations play an important role in the electron-phonon coupling. Di erent from previous theoretical results, our calculated electron-phonon coupling constant is 0.39 and the estimated …
Diamond and cBN are two of the most promising ultra-wide-band-gap (UWBG) semiconductors for applications in high-power high-frequency electronic devices. Yet despite extensive studies on carrier transport in these materials, there are large discrepancies in their reported carrier mobilities. In this work, we investigate the phonon- and dopant-limited electron and hole mobility of cBN and diamond with atomistic first-principles calculations in order to understand their fundamental upper bounds to carrier transport. Our results show that although the phonon-limited electron mobilities are compar…
In succession to the first paper (arXiv 1406.6204v5), the impurity-atom concentrations when the Fermi levels are either at the valence band maximum (VBM) or the conduction band minimum (CBM) were identified for diamond, cubic boron nitride (cBN), and hexagonal boron nitride (hBN) using the Korringa-Kohn-Rostoker (KKR) scheme using the local density approximation (LDA). In the present paper, the generalized gradient approximation (GGA) was used instead of the LDA for exchange-correlation. The impurity atoms were B and N for diamond, Be, Si, and C for cBN, and Be for hBN; these impurity atoms we…
We report the results of the investigation of bulk and surface acoustic phonons in the undoped and boron-doped single-crystal diamond films using the Brillouin-Mandelstam light scattering spectroscopy. The evolution of the optical phonons in the same set of samples was monitored with Raman spectroscopy. It was found that the frequency and the group velocity of acoustic phonons decrease non-monotonically with the increasing boron doping concentration, revealing pronounced phonon softening. The change in the velocity of the shear horizontal and the high-frequency pseudo-longitudinal acoustic pho…
We report optical reflectivity study on pure and boron-doped diamond films grown by a hot-filament chemical vapor deposition method. The study reveals the formation of an impurity band close to the top of the valence band upon boron-doping. A schematic picture for the evolution of the electronic structure with boron doping was drawn based on the experimental observation. The study also reveals that the boron doping induces local lattice distortion, which brings an infrared-forbidden phonon mode at 1330 cm$^{-1}$ activated in doped sample. The antiresonance characteristic of the mode in conduct…
In this paper, we describe the modification of Nanoscale Impedance Microscopy (NIM), namely, a combination of contact-mode atomic force microscopy with local impedance measurements. The postulated approach is based on the application of multifrequency voltage perturbation instead of standard frequency-by-frequency analysis, which among others offers more time-efficient and accurate determination of the resultant impedance spectra with high spatial resolution. Based on the impedance spectra analysis with an appropriate electric equivalent circuit, it was possible to map surface resistance and c…
Diamond has outstanding physical properties: the hardest known material, a wide band gap, the highest thermal conductivity, and a very high Debye temperature. In 2004, Ekimov et al. discovered that heavily boron-doped (B-doped) diamond becomes a superconductor around 4 K. Our group successfully controlled the boron concentration and synthesized homoepitaxially grown superconducting diamond films by a CVD method. By CVD method, we found that superconductivity appears when the boron concentration (nB) exceeds a metal-insulator transition concentration of 3.0x10^20 cm^-3 and its Tczero increases …
We report on the transport properties of nanostructures made from boron-doped superconducting diamond. Starting from nanocrystalline superconducting boron-doped diamond thin films, grown by Chemical Vapor Deposition, we pattern by electron-beam lithography devices with dimensions in the nanometer range. We show that even for such small devices, the superconducting properties of the material are well preserved: for wires of width less than $100\, nm$, we measure critical temperatures in the Kelvin range and critical field in the Tesla range.
Expressions for dependences of the pre-exponential factor σ_3 and the thermal activation energy ε_3 of hopping electric conductivity of holes via boron atoms on the boron atom concentration N and the compensation ratio K are obtained in the quasiclassical approximation. It is assumed that the acceptors (boron atoms) in charge states (0) and (-1) and the donors that compensate them in the charge state (+1) form a nonstoichiometric simple cubic lattice with translational period R_h = [(1 + K)N]^{-1/3} within the crystalline matrix. A hopping event occurs only over the distance R_h at a thermally…
A high-current annealing technique is used to fabricate nanogaps and hybrid diamond/graphite structures in boron-doped nanocrystalline diamond films. Nanometer-sized gaps down to 1 nm are produced using a feedback-controlled current annealing procedure. The nanogaps are characterized using scanning electron microscopy and electronic transport measurements. The structural changes produced by the elevated temperature, achieved by Joule heating during current annealing, are characterized using Raman spectroscopy. The formation of hybridized diamond/graphite structure is observed at the point of m…
Superconductivity of boron-doped diamond, reported recently at T_c=4 K, is investigated exploiting its electronic and vibrational analogies to MgB2. The deformation potential of the hole states arising from the C-C bond stretch mode is 60% larger than the corresponding quantity in MgB2 that drives its high Tc, leading to very large electron-phonon matrix elements. The calculated coupling strength λ~ 0.5 leads to T_c in the 5-10 K range and makes phonon coupling the likely mechanism. Higher doping should increase T_c somewhat, but effects of three dimensionality primarily on the density of stat…
X-ray absorption (XAS) and emission (XES) spectroscopy near B-K and C-K edges have been performed on metallic (~1at%B, B-diamond) and semiconducting (~0.1at%B and N, BN-diamond) doped-diamond films. Both B-K XAS and XES spectra shows metallic partial density of state (PDOS) with the Fermi energy of 185.3 eV, and there is no apparent boron-concentration dependence in contrast to the different electric property. In C-K XAS spectrum of B-diamond, the impurity state ascribed to boron is clearly observed near the Fermi level. The Fermi energy is found to be almost same with the top of the valence b…
Isotopic enrichment offers cutting-edge properties of materials opening exciting research and development opportunities. In semiconductors, reached progress of ultimate control in growth and doping techniques follows nowadays the high level isotopic purification. This requires deep understanding of isotopic disorder effects and techniques of their effective determination. Isotopic content of both crystal lattice and impurity centers cause the effects, which can be examined by different optical techniques. While disorder in the host lattice can be straight forward evaluated by inelastic light s…
We observe the electron spin resonance of conduction electrons in boron doped (6400 ppm) superconducting diamond (Tc =3.8 K). We clearly identify the benchmarks of conduction electron spin resonance (CESR): the nearly temperature independent ESR signal intensity and its magnitude which is in good agreement with that expected from the density of states through the Pauli spin-susceptibility. The temperature dependent CESR linewidth weakly increases with increasing temperature which can be understood in the framework of the Elliott-Yafet theory of spin-relaxation. An anomalous and yet unexplained…
We predict a new three-dimensional (3D) boron allotrope based on systematic first-principles electronic structure calculations. This allotrope can be derived by substituting each carbon atom in a hexagonal diamond lattice with a B$_{4}$ tetrahedron and possesses the same space group $P6_{3}/mmc$ as hexagonal diamond, hence it is termed as H-boron. We show that H-boron has good stability and excellent mechanical property. Remarkably, we find that H-boron is a topological metal with rich types of spin-orbit-free emergent fermions, including semi-Dirac fermion, quadratic and linear triple-point f…
Ultrananocrystalline diamond/hydrogenated amorphous carbon composite thin films synthesized via coaxial arc plasma possess a marked structural feature of diamond grains embedded in an amorphous carbon and a hydrogenated amorphous carbon matrix which are the largest constituents of the films. Since the amorphous nature yields much larger light absorption coefficients as well as a generation source of photo-induced carriers with UV rays, these films can be potential candidates for deep-UV photodetector applications. From some previous studies p-type conduction of the films has been realized by d…
We report a study of the relaxation time of the restoration of the resistive superconducting state in single crystalline boron-doped diamond using amplitude-modulated absorption of (sub-)THz radiation (AMAR). The films grown on an insulating diamond substrate have a low carrier density of about 2.5x10^{21} cm^{-3} and a critical temperature of about 2 K. By changing the modulation frequency we find a high-frequency rolloff which we associate with the characterstic time of energy relaxation between the electron and the phonon systems or the relaxation time for nonequilibrium superconductivity. …
Electrical conductivity of a highly boron doped chemical vapor deposited diamond thin film has been studied at different temperatures under high electric field conditions. Current-voltage characteristics have been measured using pulsed technique to reduce thermal effects. Experimental results evidence deep impurity impact ionization avalanche in p-type diamond up to room temperature.
Boron-doped diamond (BDD) has attracted much attentions in semi-/super-conductor physics and electrochemistry, where the surface structures play crucial roles. Herein, we systematically re-examined the probable surface reconstructions of the bare and H-terminated BDD(100) and (111) surfaces by using density functional theory (DFT). For the optimized structures, we performed STM image simulations based on Tersoff-Hamman scheme and calculations of the projected density of states. We found that: on the BDD(100), the p(2x1) reconstruction has lowest energy and the c(2x2) reconstruction has 0.1673 …
Polarized negative muons were used to study the behaviour of the boron acceptor centre in synthetic diamond produced by the chemical vapour deposition (CVD) method. The negative muon substitutes one of the electrons in a carbon atom, and this muonic atom imitates the boron acceptor impurity in diamond. The temperature dependence of the muon spin relaxation rate and spin precession frequency were measured in the range of 20 - 330 K in a transverse magnetic field of 14 kOe. For the first time a negative shift of the muon spin precession was observed in diamond. It is tentatively attributed to an…
A review of electronic properties of insulating-, boron- and phosphorus-doped diamond is given. The main goal is, to show data in a wider context, to reveal trends and limitations with respect to carrier mobilities, conductivities, p- and n-type doping. Undoped diamond is an insulator with conductivities significantly smaller than 10^-17 Ohmcm at room temperature. Mostly, these insulating films show conductivity activation energies of 1.7 eV, an indication that small amounts of substitutional nitrogen dominates the Fermi-level. The electron and hole mobilities are very high (> 20.000 cm2/Vs at…
Improvement of Morphology and Electrical Properties of Boron-doped Diamond Films via Seeding with HPHT Nanodiamonds Synthesized from 9-Borabicyclononane
Comparison of periodic B dopants with a random alloy of substitional boron in diamond is carried out using several supercells and the coherent potential approximation (CPA) for the random alloy case. The main peak in the B local density of states is shifted to lower binding energy compared to the corresponding C peak in intrinsic diamond. In supercells, this shows up as strongly B-character bands split from bulk C bands away from the zone center,in an energy region around -1 eV. Even for a 4*4*4 supercell (BC$_{127}$), effects of the dopant order are evident in the form of primarily B-characte…
We report the discovery of superconductivity in boron-doped diamond synthesized at high pressure (8-9 GPa) and temperature (2,500-2,800 K). Electrical resistivity, magnetic susceptibility, specific heat, and field-dependent resistance measurements show that boron-doped diamond is a bulk, type-II superconductor below the superconducting transition temperature Tc=4 K; superconductivity survives in a magnetic field up to Hc2(0)=3.5 T. The discovery of superconductivity in diamond-structured carbon suggests that Si and Ge, which also form in the diamond structure, may similarly exhibit superconduc…
A phase slip is a localized disturbance in the coherence of a superconductor allowing an abrupt 2$π$ phase shift. Phase slips are a ubiquitous feature of one-dimensional superconductors and also have an analogue in two-dimensions. Here we present electrical transport measurements on boron-doped nanocrystalline diamond (BNCD) microbridges where, despite their three-dimensional macroscopic geometry, we find clear evidence of phase slippage in both the resistance-temperature and voltage-current characteristics. We attribute this behavior to the unusual microstructure of BNCD. We argue that the co…
Cubic boron phosphide BP has been studied in situ by X-ray diffraction and Raman scattering up to 55 GPa at 300 K in a diamond anvil cell. The bulk modulus of B0 = 174(2) GPa has been established, which is in excellent agreement with our ab initio calculations. The data on Raman shift as a function of pressure, combined with equation-of-state data, allowed us to estimate the Grüneisen parameters of the TO and LO modes of zinc-blende structure, γGTO = 1.16 and γGLO = 1.04, just like in the case of other AIIIBV diamond-like phases, for which γGTO > γGLO = 1. We also established that the pressure…
Interface phonon modes governing the ideal limit of thermal transport across diamond/cubic boron nitride interfaces
School of Science, Harbin Institute of Technology, Shenzhen（哈尔滨工业大学（深圳）理学院）；Institute of Industrial Science, The University of Tokyo（东京大学工业科学研究所）；Department of Physical Chemistry, School of Chemistry, Tel Aviv University（特拉维夫大学化学学院物理化学系）；College of Physical Science and Technology, Bohai University（渤海大学物理科学与技术学院）；Ministry of Industry and Information Technology Key Laboratory of Micro-Nano Optoelectronic Information System, Harbin Institute of Technology, Shenzhen（工业和信息化部微纳光电子信息系统重点实验室，哈尔滨工业大学（深圳））；Collaborative Innovation Center of Extreme Optics, Shanxi University（山西大学极端光学协同创新中心）
Diamond is an electrical insulator in its natural form. However, when doped with boron above a critical level (~0.25 at.%) it can be rendered superconducting at low temperatures with high critical fields. Here we present the realization of a micrometer scale superconducting quantum interference device $μ$-SQUID made from nanocrystalline boron doped diamond (BDD) films. Our results demonstrate that $μ$-SQUIDs made from superconducting diamond can be operated in magnetic fields as large as 4T independent on the field direction. This is a decisive step towards the detection of quantum motion in a…
Hole doping can control the conductivity of diamond either through boron substitution, or carrier accumulation in a field-effect transistor. In this work, we combine the two methods to investigate the insulator-to-metal transition at the surface of nanocrystalline diamond films. The finite boron doping strongly increases the maximum hole density which can be induced electrostatically with respect to intrinsic diamond. The ionic gate pushes the conductivity of the film surface away from the variable-range hopping regime and into the quantum critical regime. However, the combination of the stron…
The deposition of boron-doped amorphous carbon thin films on SiO2 substrate was achieved via a focused ion beam-assisted chemical vapor deposition of triphenyl borane (C18H15B) and triphenyl borate (C18H15BO3). The existence of boron in the deposited film from triphenyl borane, with a precursor temperature of 90 °C, was confirmed by a core level X-ray photoelectron spectroscopy analysis. The film exhibited a semiconducting behavior with a band gap of 285 meV. Although the band gap was decreased to 197 meV after an annealing process, the film was still semiconductor. Additionally, a drastic red…
Diamond, a well-known wide-bandgap insulator, becomes a low-temperature superconductor upon substitutional doping of carbon with boron. However, limited boron solubility and significant lattice disorder introduced by boron doping prevent attaining the theoretically-predicted high-temperature superconductivity. Here we present an alternative co-doping approach, based on the combination of ionic gating and boron substitution, in hydrogenated thin films epitaxially grown on (111)- and (110)-oriented single crystals. Gate-dependent electric transport measurements show that the effect of boron dopi…
Electrochemically switchable selective membranes play an important role in selective filtration processes such as water desalination, industrial waste treatment and hemodialysis. Currently, membranes for these purposes need to be optimized in terms of electrical conductivity and stability against fouling and corrosion. In this paper, we report the fabrication of boron-doped diamond membrane by template diamond growth on quartz fiber filters. The morphology and quality of the diamond coating are characterized via SEM and Raman spectroscopy. The membrane is heavily boron doped (> 1021 cm-3) with…
Theoretical predictions of pressure-induced phase transformations often become long-standing enigmas because of limitations of contemporary available experimental possibilities. Hitherto the existence of a non-icosahedral boron allotrope has been one of them. Here we report on the first non-icosahedral boron allotrope, which we denoted as ζ-B, with the orthorhombic α-Ga-type structure (space group Cmce) synthesized in a diamond anvil cell at extreme high-pressure high-temperature conditions (115 GPa and 2100 K). The structure of ζ-B was solved using single-crystal synchrotron X-ray diffraction…
