Submitted to IEEE Transactions on Wireless Communications, under second round of revisions. 10 pages, 8 figures. arXiv admin note: text overlap with arXiv:1406.4610
In a multiway relay channel (MWRC), pairwise transmission strategy can be used to reduce the computational complexity at the relay and the users without sacrificing the data rate, significantly. The performance of such pairwise strategies, however, is affected by the way that the users are paired to transmit. In this paper, we study the effect of pairing on the common rate and sum rate of an MWRC with functional-decode-forward (FDF) relaying strategy where users experience asymmetric channel conditions. To this end, we first develop a graphical model for an MWRC with pairwise transmission strategy. Using this model, we then find the maximum achievable common rate and sum rate as well as the user pairings that achieve these rates. This marks the ultimate performance of FDF relaying in an MWRC setup. Further, we show that the rate enhancement achieved through the optimal user pairing becomes less pronounced at higher SNRs. Using computer simulations, the performance of the optimal pairing is compared with those of other proposed pairings in the literature.
We consider efficient communications over the multiple-input multiple-output (MIMO) multiway distributed relay channel (MDRC) with full data exchange, where each user, equipped with multiple antennas, broadcasts its message to all the other users via the help of a number of distributive relays. We propose a physical-layer network coding (PNC) based scheme involving linear precoding for channel alignment nested lattice coding for PNC, and lattice-based precoding for interference mitigation, We show that, with the proposed scheme, distributed relaying achieves the same sum-rate as cooperative re…
The L-user additive white Gaussian noise multiway relay channel is investigated, where L users exchange information at the same rate through a single relay. A new achievable rate region, based on the functional-decode-forward coding strategy, is derived. For the case where there are three or more users, and all nodes transmit at the same power, the capacity is obtained. For the case where the relay power scales with the number of users, it is shown that both compress-forward and functional-decode-forward achieve rates within a constant number of bits of the capacity at all SNR levels; in addit…
To address the coverage and capacity challenges in fifth-generation (5G) wireless networks, the relay technique has been considered as a promising solution and recently attracted great attentions from academia. The multiway relay channel (mRC), which serves as a fundamental building block of a relay network, defines the family of all possible information-flow patterns between a relay node and its neighboring nodes. Combined with several new techniques, such as physical-layer network coding (PLNC), signal and interference alignments, multi-input multi-output (MIMO), etc., the mRC exhibits super…
We consider a joint source-channel coding problem on a finite-field multiway relay channel, and we give closed-form lower and upper bounds on the optimal source-channel rate. These bounds are shown to be tight for all discrete memoryless sources in a certain class $\mathcal{P}^*$, and we demonstrate that strict source-channel separation is optimal within this class. We show how to test whether a given source belongs to $\mathcal{P}^*$, we give a balanced-information regularity condition for $\mathcal{P}^*$, and we express $\mathcal{P}^*$ in terms of conditional multiple-mutual informations. Fi…
In this paper, we study the effect of users' transmission ordering on the common rate and sum rate of pairwise multiway relay channels (MWRCs) with functional-decode-forward strategy. To this end, we first develop a graphical model for the data transmission in a pairwise MWRC. Using this model, we then find the optimal orderings that achieve the maximum common rate and sum rate of the system. The achieved maximum common and sum rate are also found. Moreover, we show that the performance gap between optimal orderings and a random ordering vanishes when SNR increases. Computer simulations are pr…
We investigate achievable degrees of freedom (DoF) for a multiple-input multiple-output (MIMO) multiway relay channel (mRC) with $L$ clusters and $K$ users per cluster. Each user is equipped with $M$ antennas and the relay with $N$ antennas. We assume a new data exchange model, termed \emph{clustered full data exchange}, i.e., each user in a cluster wants to learn the messages of all the other users in the same cluster. Novel signal alignment techniques are developed to systematically construct the beamforming matrices at the users and the relay for efficient physical-layer network coding. Bas…
In this paper, we propose a new distributed energy beamforming and information transfer (DEBIT) scheme for realizing simultaneous wireless information and power transfer (SWIPT) in multiway relay networks (MWRNs), where multiple single-antenna users exchange information via an energy-constrained single-antenna relay node. We investigate the optimal transceiver designs to maximize the achievable sum-rate or the harvested power. The resultant sum-rate maximization problem is non-convex and the global optimal solution can be obtained through a three-dimensional search in combination with conventi…
In this paper, we study achievable degrees of freedom (DoF) of a multiple-input multiple-output (MIMO) multiway relay channel (mRC) where $K$ users, each equipped with $M$ antennas, exchange messages in a pairwise manner via a common $N$-antenna relay node. % A novel and systematic way of joint beamforming design at the users and at the relay is proposed to align signals for efficient implementation of physical-layer network coding (PNC). It is shown that, when the user number $K=3$, the proposed beamforming design can achieve the DoF capacity of the considered mRC for any $(M,N)$ setups. % Fo…
The multi-way relay channel is a multicast network where L users exchange data through a relay. In this paper, the capacity region of a class of multi-way relay channels is derived, where the channel inputs and outputs take values over finite fields. The cut-set upper bound to the capacity region is derived and is shown to be achievable by our proposed functional-decode-forward coding strategy. More specifically, for the general case where the users can transmit at possibly different rates, functional-decode-forward, combined with rate splitting and joint source-channel decoding, is proved to …
Considering two-hop cooperative communication with buffered half-duplex relays, this work jointly optimizes relay selection and transmit power at the relay to maximize the sum-throughput of the network subject to a minimum throughput requirement of each hop and transmit power constraint. The optimization problem is solved and two new buffer aware selection schemes, namely joint relay power allocation and selection scheme (JPASS) and ratio selection scheme (RSS) are proposed. Numerical results show that the average sum-throughput of both the proposed schemes is up to 40% higher compared to the …
Results for Gaussian relay channels typically focus on maximizing transmission rates for given locations of the source, relay and destination. We introduce an alternative perspective, where the objective is maximizing coverage for a given rate. The new objective captures the problem of how to deploy relays to provide a given level of service to a particular geographic area, where the relay locations become a design parameter that can be optimized. We evaluate the decode and forward (DF) and compress and forward (CF) strategies for the relay channel with respect to the new objective of maximizi…
This paper concerns maximizing the minimum achievable secrecy rate of a two-way relay network in the presence of an eavesdropper, in which two nodes aim to exchange messages in two hops, using a multi-antenna relay. Throughout the first hop, the two nodes simultaneously transmit their messages to the relay. In the second hop, the relay broadcasts a combination of the received information to the users such that the transmitted signal lies in the null space of the eavesdropper's channel; this is called null space beamforming (NSBF). The best NSBF matrix for maximizing the minimum achievable secr…
In this paper we study and analyze coverage region for half-duplex multiple-input multiple-output (MIMO) relay channel with amplify-and-forward (AF) strategy at the relay station. By assuming mixed Rayleigh and Rician fading channels with two different relay station situations, we consider the objective of maximizing coverage region for a given transmission rate and find the optimal relay location in the sense of maximizing coverage region. using Monte Carlo simulations, the coverage region and capacity bounds are shown for different fading cases and different relay station locations. Finally,…
Deploying relays and/or mobile base stations is a major means of extending the coverage of a wireless network. This paper presents models, analytical results, and algorithms to answer two related questions: The first is where to deploy relays in order to extend the reach from a base station to the maximum; the second is where to deploy a mobile base station and how many relays are needed to reach any point in a given area. Simple time-division and frequency-division scheduling schemes as well as an end-to-end data rate requirement are assumed. An important use case of the results is in the Pub…
It is known that circularly symmetric Gaussian signals are the optimal input signals for the partial decode-and-forward (PDF) coding scheme in the Gaussian multiple-input multiple-output (MIMO) relay channel, but there is currently no method to find the optimal covariance matrices nor to compute the optimal achievable PDF rate since the optimization is a non-convex problem in its original formulation. In this paper, we show that it is possible to find a convex reformulation of the problem by means of an approximation and a primal decomposition. We derive an explicit solution for the inner prob…
In this paper, with the help of an intelligent reflecting surface (IRS), the source (S) and destination (D) exchange information through the two-way decode-and-forward relay (TW-DFR). We mainly focus on the phase optimization of IRS to improve the system rate performance. Firstly, a maximizing receive power sum (Max-RPS) method is proposed via eigenvalue decomposition (EVD) with an appreciable rate enhancement, which is called Max-RPS-EVD. To further achieve a higher rate, a method of maximizing minimum rate (Max-Min-R) is proposed with high complexity. To reduce its complexity, a low-complexi…
In this paper, we study the degrees of freedom (DoF) of the symmetric multi-relay multiple-input multiple-output (MIMO) Y channel, where three user nodes, each with M antennas, communicate via K geographically separated relay nodes, each with N antennas. For this model, we establish a general DoF achievability framework based on linear precoding and post-processing methods. The framework poses a nonlinear problem with respect to user precoders and post-processors, as well as relay precoders. To solve this problem, we adopt an uplink-downlink asymmetric strategy, where the user precoders are de…
In this paper, an intelligent reflecting surface (IRS)-aided two-way decode-and-forward (DF) relay wireless network is considered, where two users exchange information via IRS and DF relay. To enhance the sum rate performance, three power allocation (PA) strategies are proposed. Firstly, a method of maximizing sum rate (Max-SR) is proposed to jointly optimize the PA factors of user U1, user U2 and relay station (RS). To further improve the sum rate performance, two high-performance schemes, namely maximizing minimum sum rate (Max-Min-SR) and maximizing sum rate with rate constraint (Max-SR-RC)…
We study and analyze coverage region in MIMO communication systems for a multiple-relay network with decode-and-forward (DF) strategy at the relays. Assuming that there is a line-of-sight (LOS) propagation environment for source-relay channels and channel state information is available at receivers (CSIR), we consider the objective of maximizing coverage region for a given transmission rate and show numerically the significant effect of propagation environment on capacity bounds, optimal relay location and coverage region. Also, we study the situation in which two adjacent relays cooperate in …
We consider a multi-pair two-way amplify-and-forward massive multi-input multi-output (MIMO) hybrid relay with MIMO user-pairs. A hybrid relay has lesser number of radio frequency (RF) chains than the antennas, which significantly reduces the implementation cost. We employ block-diagonalization-based baseband processing at the hybrid relay to cancel the inter user-pair interference and equal-gain-combining-based RF processing to maximize the beamforming gain. We also use an algebraic norm maximizing relay transmit strategy to maximize the spectral efficiency (SE) of each user-pair. We numerica…
This paper studies the achievable degrees of freedom for multi-user MIMO two-way relay channels, where there are $K$ source nodes, each equipped with $M$ antennas, one relay node, equipped with $N$ antennas, and each source node exchanges independent messages with an arbitrary set of other source nodes via the relay. By allowing an arbitrary information exchange pattern, the considered channel model is a unified one. It includes several existing channel models as special cases: $K$-user MIMO Y channel, multi-pair MIMO two-way relay channel, generalized MIMO two-way X relay channel, and $L$-clu…
This contribution presents a method of obtaining the optimal power and subcarrier allocations that maximize the energy-efficiency (EE) of a multi-user, multi-relay, orthogonal frequency division multiple access (OFDMA) cellular network. Initially, the objective function (OF) is formulated as the ratio of the spectral-efficiency (SE) over the power consumption of the network. This OF is shown to be quasi-concave, thus Dinkelbach's method can be employed for solving it as a series of parameterized concave problems. We characterize the performance of the aforementioned method by comparing the opt…
In this paper, we study a multi-user multi-relay interference-channel network, where energy-constrained relays harvest energy from sources' radio frequency (RF) signals and use the harvested energy to forward the information to destinations. We adopt the interference alignment (IA) technique to address the issue of interference, and propose a novel transmission scheme with the IA at sources and the power splitting (PS) at relays. A distributed and iterative algorithm to obtain the optimal PS ratios is further proposed, aiming at maximizing the sum rate of the network. The analysis is then vali…
Relay-aided transmission is envisioned as a key strategy to combat severe path loss and link blockages emerging as unique challenges in millimeter-wave (mmWave) communications. This work considers a relay-aided multiuser mmWave communications scenario aiming at maximizing the sum rate through optimal transmit and relay precoder design. We propose a novel joint precoder design strategy, which exploits weighted minimum mean-square error (WMMSE) using its equivalency to sum-rate maximization. We obtain closed form expressions of transmit and relay precoders, and propose to compute them through al…
In this paper, we investigate the robust transceiver design for dual-hop amplify-and-forward (AF) MIMO relay systems with Gaussian distributed channel estimation errors. Aiming at maximizing the mutual information under imperfect channel state information (CSI), source precoder at source and forwarding matrix at the relay are jointly optimized. Using some elegant attributes of matrix-monotone functions, the structures of the optimal solutions are derived first. Then based on the derived structure an iterative waterfilling solution is proposed. Several existing algorithms are shown to be specia…
In this paper we investigate the optimal relay location in the sense of maximizing suitably defined coverage region for MIMO relay channel. We consider the general Rayleigh fading case and assume that the channel state information is only available at the receivers (CSIR), which is an important practical case in applications such as cooperative vehicular communications. In order to overcome the mathematical difficulty regarding determination of the optimal relay location, we provide two analytical solutions, and show that it is possible to determine the optimal relay location (for a desired tr…
The problem of resource allocation is studied for a two-user fading orthogonal multiaccess relay channel (MARC) where both users (sources) communicate with a destination in the presence of a relay. A half-duplex relay is considered that transmits on a channel orthogonal to that used by the sources. The instantaneous fading state between every transmit-receive pair in this network is assumed to be known at both the transmitter and receiver. Under an average power constraint at each source and the relay, the sum-rate for the achievable strategy of decode-and-forward (DF) is maximized over all po…
The cooperative automatic repeat request (C-ARQ) is a link layer relaying protocol which exploits the spatial diversity and allows the relay node to retransmit the source data packet to the destination, when the latter is unable to decode the source data correctly. This paper presents a cross-layer link adaptation design for C-ARQ based relay channels in which both source and relay nodes employ adaptive modulation coding and power adaptation at the physical layer. For this scenario, we first derive closed-form expressions for the system spectral efficiency and average power consumption. We the…
This paper considers the problem of selecting a subset of nodes in a two-hop wireless network to act as relays in aiding the communication between the source-destination pair. Optimal relay subset selection with the objective of maximizing the overall throughput is a difficult problem that depends on multiple factors including node locations, queue lengths and power consumption. A partial decode-and-forward strategy is applied in this paper to improve the tractability of the relay selection problem and performance of the overall network. Note that the number of relays selected ultimately deter…
This paper addresses robust communication on a fading relay channel in which the relay is connected to the decoder via an out-of-band digital link of limited capacity. Both the source-to-relay and the source-to-destination links are subject to fading gains, which are generally unknown to the encoder prior to transmission. To overcome this impairment, a hybrid automatic retransmission request (HARQ) protocol is combined with multi-layer broadcast transmission, thus allowing for variable-rate decoding. Moreover, motivated by cloud radio access network applications, the relay operation is limited…
The capacity of a relay channel with inter-symbol interference (ISI) and additive colored Gaussian noise is examined under an input power constraint. Prior results are used to show that the capacity of this channel can be computed by examining the circular degraded relay channel in the limit of infinite block length. The current work provides single letter expressions for the achievable rates with decodeand- forward (DF) and compress-and-forward (CF) processing employed at the relay. Additionally, the cut-set bound for the relay channel is generalized for the ISI/colored Gaussian noise scenari…
Two-way relaying can considerably improve spectral efficiency in relay-assisted bidirectional communications. However, the benefits and flexible structure of orthogonal frequency division multiplexing (OFDM)-based two-way decode-and-forward (DF) relay systems is much less exploited. Moreover, most of existing works have not considered quality-of-service (QoS) provisioning for two-way relaying. In this paper, we consider the OFDM-based bidirectional transmission where a pair of users exchange information with or without the assistance of a single DF relay. Each user can communicate with the oth…
In this paper we explore the use of full-duplex radio to improve the spectrum efficiency in a two-way relay channel where two sources exchange information through an multi-antenna relay, and all nodes work in the full-duplex mode. The full-duplex operation can reduce the overall communication to only one phase but suffers from the self-interference. Instead of purely suppressing the self-interference, we aim to maximize the end-to-end performance by jointly optimizing the beamforming matrix at the relay which uses the amplify-and-forward protocol as well as the power control at the sources. To…
In this paper, we consider a non-orthogonal multiple access cognitive radio network, where a full-duplex multi-antenna relay assists transmission from a base station (BS) to a cognitive far user, whereas, at the same time, the BS transmits to a cognitive near user. Our objective is to enlarge the far-near user rate region by maximizing the rate of the near user under a constraint that the rate of the far user is above a certain threshold. To this end, a non-convex joint optimization problem of relay beamforming and the transmit powers at the BS and cognitive relay is solved as a semi-definite …
We consider a multiple-input multiple-output (MIMO) relaying boardcast channel in downlink cellular networks, where the base station and the relay stations are both equipped with multiple antennas, and each user terminal has only a single antenna. In practical scenarios, channel estimation is imperfect at the receivers. Aiming at maximizing the SINR at each user, we develop two robust linear beamforming schemes respectively for the single relay case and the multi-relay case. The two proposed schemes are based on sigular value decomposition (SVD), minimum mean square error (MMSE) and regularize…
We analyze coding for energy efficiency in relay channels at a fixed source rate. We first propose a half-duplex decode-forward coding scheme for the Gaussian relay channel. We then derive three optimal sets of power allocation, which respectively minimize the network, the relay and the source energy consumption. These optimal power allocations are given in closed-form, which have so far remained implicit for maximum-rate schemes. Moreover, analysis shows that minimizing the network energy consumption at a given rate is not equivalent to maximizing the rate given energy, since it only covers p…
We provide a geometric solution to the problem of optimal relay positioning to maximize the multicast rate for low-SNR networks. The networks we consider, consist of a single source, multiple receivers and the only intermediate and locatable node as the relay. We construct network the hypergraph of the system nodes from the underlying information theoretic model of low-SNR regime that operates using superposition coding and FDMA in conjunction (which we call the "achievable hypergraph model"). We make the following contributions. 1) We show that the problem of optimal relay positioning maximiz…
We propose a secure transmission scheme for a relay wiretap channel, where a source communicates with a destination via a decode-and-forward relay in the presence of spatially random-distributed eavesdroppers. We assume that the source is equipped with multiple antennas, whereas the relay, the destination, and the eavesdroppers are equipped with a single antenna each. In the proposed scheme, in addition to information signals, the source transmits artificial noise signals in order to confuse the eavesdroppers. With the target of maximizing the secrecy throughput of the relay wiretap channel, w…
In this paper, we propose a novel algorithm to maximize the sum rate in interference-limited scenarios where each user decodes its own message with the presence of unknown interferences and noise considering the signal-to-interference-plus-noise-ratio. It is known that the problem of adapting the transmit and receive filters of the users to maximize the sum rate with a sum transmit power constraint is non-convex. Our novel approach is to formulate the sum rate maximization problem as an equivalent multi-convex optimization problem by adding two sets of auxiliary variables. An iterative algorit…
In this letter, we analyze the ergodic capacity of bidirectional amplify-and-forward relay selection (RS) with imperfect channel state information (CSI), i.e., outdated CSI and imperfect channel estimation. Practically, the optimal RS scheme in maximizing the ergodic capacity cannot be achieved, due to the imperfect CSI. Therefore, two suboptimal RS schemes are discussed and analyzed, in which the first RS scheme is based on the imperfect channel coefficients, and the second RS scheme is based on the predicted channel coefficients. The lower bound of the ergodic capacity with imperfect CSI is …
This paper presents a cross-layer approach to jointly design adaptive modulation and coding (AMC) at the physical layer and cooperative truncated automatic repeat request (ARQ) protocol at the data link layer. We first derive an exact closed form expression for the spectral efficiency of the proposed joint AMC-cooperative ARQ scheme. Aiming at maximizing this system performance measure, we then optimize an AMC scheme which directly satisfies a prescribed packet loss rate constraint at the data-link layer. The results indicate that utilizing cooperative ARQ as a retransmission strategy, noticea…
The problem of power allocation is studied for a multiple-input multiple-output (MIMO) decode-and-forward (DF) two-way relaying system consisting of two source nodes and one relay. It is shown that achieving maximum sum-rate in such a system does not necessarily demand the consumption of all available power at the relay. Instead, the maximum sum-rate can be achieved through efficient power allocation with minimum power consumption. Deriving such power allocation, however, is nontrivial due to the fact that it generally leads to a nonconvex problem. In Part I of this two-part paper, a sum-rate …
In this paper, we examine the physical layer security for cooperative wireless networks with multiple intermediate nodes, where the decode-and-forward (DF) protocol is considered. We propose a new joint relay and jammer selection (JRJS) scheme for protecting wireless communications against eavesdropping, where an intermediate node is selected as the relay for the sake of forwarding the source signal to the destination and meanwhile, the remaining intermediate nodes are employed to act as friendly jammers which broadcast the artificial noise for disturbing the eavesdropper. We further investiga…
In a cooperative relay network, a relay node (R) facilitates data transmission to the destination node (D), when the latter is unable to decode the source node (S) data correctly. This paper considers such a system model and presents a cross-layer approach to jointly design adaptive modulation and coding (AMC) at the physical layer and cooperative truncated automatic repeat request (ARQ) protocol at the data link layer. We first derive a closed form expression for the spectral efficiency of the joint cooperative ARQ-AMC scheme. Aiming at maximizing this performance measure, we then optimize tw…
To achieve the available performance gains in half-duplex wireless relay networks, several cooperative schemes have been earlier proposed using either distributed space-time coding or distributed beamforming for the transmitter without and with channel state information (CSI), respectively. However, these schemes typically have rather high implementation and/or decoding complexities, especially when the number of relays is high. In this paper, we propose a simple low-rate feedback-based approach to achieve maximum diversity with a low decoding and implementation complexity. To further improve …
In a two-way relay network, two terminals exchange information over a shared wireless half-duplex channel with the help of a relay. Due to its fundamental and practical importance, there has been an increasing interest in this channel. However, surprisingly, there has been little work that characterizes the fundamental tradeoff between the communication reliability and transmission rate across all signal-to-noise ratios. In this paper, we consider amplify-and-forward (AF) two-way relaying due to its simplicity. We first derive the random coding error exponent for the link in each direction. Fr…
Simultaneously information and power transfer in mobile relay networks have recently emerged, where the relay can harvest the radio frequency (RF) energy and then use this energy for data forwarding and system operation. Most of the previous works do not consider that the relay may have its own objectives, such as using the harvested energy for its own transmission instead of maximizing transmission of the network. Therefore, in this paper, we propose a Nash bargaining approach to balance the information transmission efficiency of source-destination pairs and the harvested energy of the relay …
This paper studies a cooperative cognitive radio network where two primary users (PUs) exchange information with the help of a secondary user (SU) that is equipped with multiple antennas and in return, the SU superimposes its own messages along with the primary transmission. The fundamental problem in the considered network is the design of transmission strategies at the secondary node. It involves three basic elements: first, how to split the power for relaying the primary signals and for transmitting the secondary signals; second, what two-way relay strategy should be used to assist the bidi…
As a low-cost and low-power-consumption passive reflector, intelligent reflecting surface (IRS) can make a significant rate improvement by building a programmable wireless environment. To improve the rate performance and coverage range of wireless networks, an IRS-aided decode-and-forward (DF) relay network is proposed with multiple antennas at relay station (RS). To achieve a high rate, an alternately iterative structure (AIS) of maximizing receive power (Max-RP) at RS is proposed to jointly optimize the beamforming vectors at RS and phase shifts at IRS. Considering its high-complexity, two l…
Maximizing the minimum rate for a full-duplex multiple-input multiple-output (MIMO) wireless network encompassing two sources and a two-way (TW) relay operating in a two hop manner is investigated. To improve the overall performance, using a zero-forcing approach at the relay to suppress the residual self-interference arising from full-duplex (FD) operation, the underlying max-min problem is cast as an optimization problem which is non-convex. To circumvent this issue, semidefinite relaxation technique is employed, leading to upper and lower bound solutions for the optimization problem. Numeri…
In this work, we present a novel robust distributed beamforming (RDB) approach to mitigate the effects of channel errors on wireless networks equipped with relays based on the exploitation of the cross-correlation between the received data from the relays at the destination and the system output. The proposed RDB method, denoted cross-correlation and subspace projection (CCSP) RDB, considers a total relay transmit power constraint in the system and the objective of maximizing the output signal-to-interference-plus-noise ratio (SINR). The relay nodes are equipped with an amplify-and-forward (AF…
The problem of security against timing based traffic analysis in wireless networks is considered in this work. An analytical measure of anonymity in eavesdropped networks is proposed using the information theoretic concept of equivocation. For a physical layer with orthogonal transmitter directed signaling, scheduling and relaying techniques are designed to maximize achievable network performance for any given level of anonymity. The network performance is measured by the achievable relay rates from the sources to destinations under latency and medium access constraints. In particular, analyti…
In this paper, we consider the Physical Layer Security(PLS) problem in orthogonal frequency division multiple access (OFDMA) based dual-hop system which consists of multiple users, multiple amplify and forward relays, and an eavesdropper. The aim is to enhance PLS of the entire system by maximizing sum secrecy rate of secret users through optimal resource allocation under various practical constraints. Specifically, the sub-carrier allocation to different users, the relay assignments, and the power loading over different sub-carriers at transmitting nodes are optimized. The joint optimization …
Cooperative Rate-Splitting (CRS) strategy, relying on linearly precoded rate-splitting at the transmitter and opportunistic transmission of the common message by the relaying user, has recently been shown to outperform typical Non-cooperative Rate-Splitting (NRS), Cooperative Non-Orthogonal Multiple Access (C-NOMA) and Space Division Multiple Access (SDMA) in a two-user Multiple Input Single Output (MISO) Broadcast Channel (BC) with user relaying. In this work, the existing two-user CRS transmission strategy is generalized to the K-user case. We study the problem of jointly optimizing the prec…
Since reconfigurable intelligent surface (RIS) is considered to be a passive reflector for rate performance enhancement, a RIS-aided amplify-and-forward (AF) relay network is presented. By jointly optimizing the beamforming matrix at AF relay and the phase shifts matrices at RIS, two schemes are put forward to address a maximizing signal-to-noise ratio (SNR) problem. Firstly, aiming at achieving a high rate, a high-performance alternating optimization (AO) method based on Charnes-Cooper transformation and semidefinite programming (CCT-SDP) is proposed, where the optimization problem is decompo…
This paper investigates power control and relay selection in Full Duplex Cognitive Relay Networks (FDCRNs), where the secondary-user (SU) relays can simultaneously receive data from the SU source and forward them to the SU destination. We study both non-coherent and coherent scenarios. In the non-coherent case, the SU relay forwards the signal from the SU source without regulating the phase; while in the coherent scenario, the SU relay regulates the phase when forwarding the signal to minimize the interference at the primary-user (PU) receiver. We consider the problem of maximizing the transmi…
