In this paper, we investigate the optimization of non-uniform linear antenna arrays (NULAs) for millimeter wave (mmWave) line-of-sight (LoS) multiple-input multiple-output (MIMO) channels. Our focus is on the maximization of the system effective multiplexing gain (EMG), by optimizing the individual antenna positions in the transmit/receive NULAs. Here the EMG is defined as the number of signal streams that are practically supported by the channel at a finite SNR. We first derive analytical expressions for the asymptotic channel eigenvalues with arbitrarily deployed NULAs when, asymptotically, the end-to-end distance is sufficiently large compared to the aperture sizes of the transmit/receive NULAs. Based on the derived expressions, we prove that, the asymptotically optimal NULA deployment that maximizes the achievable EMG should follow the groupwise Fekete-point distribution. Specifically, the antennas should be physically grouped into K separate uniform linear antenna arrays (ULAs) with the minimum feasible antenna spacing within each ULA, where K is the target EMG to be achieved; in addition, the centers of these K ULAs follow the Fekete-point distribution. We numerically verify the asymptotic optimality of such an NULA deployment and extend it to a groupwise projected arch type (PAT) NULA deployment, which provides a more practical option for mmWave LoS MIMO systems with realistic non-asymptotic configurations. Numerical examples are provided to demonstrate a significant capacity gain of the optimized NULAs over traditional ULAs.
Omnidirectional path loss models are vital for radiosystem design in wireless communication systems, as they allow engineers to perform network simulations for systems with arbitrary antenna patterns. At millimeter-wave frequencies, channel measurements are frequently conducted using steerable highgain directional antennas at both the transmitter and receiver to make up for the significant increase in free space path loss at these frequencies compared to traditional cellular systems that operate at lower frequencies. The omnidirectional antenna pattern, and resulting omnidirectional received p…
In this paper, we present a low overhead beam management approach for near-field millimeter-wave multi-antenna communication systems enabled by Reconfigurable Intelligent Surfaces (RISs). We devise a novel variable-width hierarchical phaseshift codebook suitable for both the near- and far-field of the RIS, and present a fast alignment algorithm for the RIS phase shifts and the transceiver beamformers. Indicative performance evaluation results are shown, verifying the effectiveness of the proposed approach in comparison with various benchmark schemes.
This paper presents a 3-dimensional millimeter-wave statistical channel impulse response model from 28 GHz and 73 GHz ultrawideband propagation measurements. An accurate 3GPP-like channel model that supports arbitrary carrier frequency, RF bandwidth, and antenna beamwidth (for both omnidirectional and arbitrary directional antennas), is provided. Time cluster and spatial lobe model parameters are extracted from empirical distributions from field measurements. A step-by-step modeling procedure for generating channel coefficients is shown to agree with statistics from the field measurements, thu…
This article presents measurement guidelines and verification procedures for antenna cross-polarization discrimination (XPD) and penetration loss measurements for millimeter wave (mmWave) channel sounder systems. These techniques are needed to ensure accurate and consistent measurements by different researchers at different frequencies and bandwidths. Measurements at 73 GHz are used to demonstrate and verify the guidelines, and show the consistency of the antenna XPD factor and the penetration loss at different transmitter-receiver (T-R) separation distances, thus providing a systematic method…
The highly sparse nature of propagation channels and the restricted use of radio frequency (RF) chains at transceivers limit the performance of millimeter wave (mmWave) multiple-input multiple-output (MIMO) systems. Introducing reconfigurable antennas to mmWave can offer an additional degree of freedom on designing mmWave MIMO systems. This paper provides a theoretical framework for studying the mmWave MIMO with reconfigurable antennas. We present an architecture of reconfigurable mmWave MIMO with beamspace hybrid analog-digital beamformers and reconfigurable antennas at both the transmitter a…
The radiation pattern of an antenna array depends on the excitation weights and the geometry of the array. Due to wind and atmospheric conditions, outdoor millimeter wave antenna elements are subject to full or partial blockages from a plethora of particles like dirt, salt, ice, and water droplets. Handheld devices are also subject to blockages from random finger placement and/or finger prints. These blockages cause absorption and scattering to the signal incident on the array, and change the array geometry. This distorts the far-field radiation pattern of the array leading to an increase in t…
Millimeter wave (mmWave) vehicular communica tion systems have the potential to improve traffic efficiency and safety. Lack of secure communication links, however, may lead to a formidable set of abuses and attacks. To secure communication links, a physical layer precoding technique for mmWave vehicular communication systems is proposed in this paper. The proposed technique exploits the large dimensional antenna arrays available at mmWave systems to produce direction dependent transmission. This results in coherent transmission to the legitimate receiver and artificial noise that jams eavesdro…
Millimeter wave (mmWave) vehicular communication systems will provide an abundance of bandwidth for the exchange of raw sensor data and support driver-assisted and safety-related functionalities. Lack of secure communication links, however, may lead to abuses and attacks that jeopardize the efficiency of transportation systems and the physical safety of drivers. In this paper, we propose two physical layer (PHY) security techniques for vehicular mmWave communication systems. The first technique uses multiple antennas with a single RF chain to transmit information symbols to a target receiver a…
This paper proposes a new multiple access technique based on the millimeter wave lens-based reconfigurable antenna systems. In particular, to support a large number of groups of users with different angles of departures (AoDs), we integrate recently proposed reconfigurable antenna multiple access (RAMA) into non-orthogonal multiple access (NOMA). The proposed technique, named reconfigurable antenna NOMA (RA-NOMA), divides the users with respect to their AoDs and channel gains. Users with different AoDs and comparable channel gains are served via RAMA while users with the same AoDs but differen…
Millimeter wave (mmWave) communication is a promising technology for the fifth-generation (5G) wireless system. However, the large number of antennas used and the wide signal bandwidth in mmWave systems render the conventional multi-antenna techniques increasingly costly in terms of signal processing complexity, hardware implementation, and power consumption. In this article, we investigate cost-effective mmWave communications by first providing an overview of the main existing techniques that offer different trade-offs between performance and cost, and then focusing our discussion on a promis…
Millimeter wave (mm-wave) communications is considered a promising technology for 5G networks. Exploiting beamforming gains with large-scale antenna arrays to combat the increased path loss at mm-wave bands is one of its defining features. However, previous works on mm-wave network analysis usually adopted oversimplified antenna patterns for tractability, which can lead to significant deviation from the performance with actual antenna patterns. In this paper, using tools from stochastic geometry, we carry out a comprehensive investigation on the impact of directional antenna arrays in mm-wave …
The densely packed antennas of millimeter-Wave (mmWave) MIMO systems are often blocked by the rain, snow, dust and even by fingers, which will change the channel's characteristics and degrades the system's performance. In order to solve this problem, we propose a cross-entropy inspired antenna array diagnosis detection (CE-AAD) technique by exploiting the correlations of adjacent antennas, when blockages occur at the transmitter. Then, we extend the proposed CE-AAD algorithm to the case, where blockages occur at transmitter and receiver simultaneously. Our simulation results show that the prop…
Hybrid analog-digital architectures are considered as promising candidates for implementing millimeter wave (mmWave) massive multiple-input multiple-output (MIMO) systems since they enable a considerable reduction of the required number of costly radio frequency (RF) chains by moving some of the signal processing operations into the analog domain. However, the analog feed network, comprising RF dividers, combiners, phase shifters, and line connections, of hybrid MIMO architectures is not scalable due to its prohibitively high power consumption for large numbers of transmit antennas. Motivated …
The ongoing commercial deployment of millimeter wave systems brings into focus a number of practical issues in form factor user equipment (UE) design. With wavelengths becoming smaller, antenna gain patterns becoming directional, and link budgets critically dependent on beamforming, it becomes imperative to use a number of antenna modules at different locations of the UE for good performance. While more antennas/modules can enhance beamforming array gains, it comes with the tradeoff of higher component cost, power consumption of the associated radio frequency circuitry, and a beam management o…
The paper introduces a high gain end-fire printed antenna operating at 14 GHz with a bandwidth of 2 GHz. The 3x3 antenna sub-array formed of this element is used to present its beam steering and multi-beam-switching capabilities for millimeter wave Massive MIMO antenna arrays of 5G networks. The co-existence of these two techniques in a Massive MIMO sub-array, aided by the use of a simple two vector excitation matrix technique, is shown in this paper. The high gain and small form factor of the antenna is useful in applications, like 5G arrays, where space is premium and the inherent layered st…
This paper presents 73 GHz human blockage measurements for a point-to-point link with a 5 m transmitter-receiver separation distance in an indoor environment, with a human that walked at a speed of approximately 1 m/s at a perpendicular orientation to the line between the transmitter and receiver, at various distances between them. The experiment measures the shadowing effect of a moving human body when using directional antennas at the transmitter and receiver for millimeter-wave radio communications. The measurements were conducted using a 500 Megachips-per-second wideband correlator channel…
Millimeter wave (mmWave) communication is a promising technology for 5G cellular systems. To compensate for the severe path loss in mmWave systems, large antenna arrays are generally used to achieve significant beamforming gains. However, due to the high hardware and power consumption cost associated with radio frequency (RF) chains, it is desirable to achieve the large-antenna gains, but with only limited number of RF chains for mmWave communications. To this end, we study in this paper a new lens antenna array enabled mmWave MIMO communication system. We first show that the array response of…
This paper is concerned with asymptotic diversity analysis for millimeter-wave (mmWave) massive MIMO systems. First, for a single-user mmWave system employing distributed antenna subarray architecture in which the transmitter and receiver consist of Kt and Kr subarrays, respectively, a diversity gain theorem is established when the numbers of antennas at subarrays go to infinity. Specifically, assuming that all subchannels have the same number of propagation paths L, the theorem states that by employing such a distributed antenna-subarray architecture, a diversity gain of KrKtL-Ns+1 can be ach…
This paper presents small-scale fading measurements for 28 GHz outdoor millimeter-wave ultrawideband channels using directional horn antennas at the transmitter and receiver. Power delay profiles were measured at half-wavelength spatial increments over a local area (33 wavelengths) on a linear track in two orthogonal receiver directions in a typical base-to-mobile scenario with fixed transmitter and receiver antenna beam pointing directions. The voltage path amplitudes are shown to follow a Rician distribution, with K-factor ranging from 9 - 15 dB and 5 - 8 dB in line of sight (LOS) and non-li…
The availability of large bandwidth at millimeter wave (mmWave) frequencies is one of the major factors that rendered very high frequencies a promising candidate enabler for fifth generation (5G) mobile communication networks. To confront with the intrinsic characteristics of signal propagation at frequencies of tens of GHz and being able to achieve data rates of the order of gigabits per second, mmWave systems are expected to employ large antenna arrays that implement highly directional beamforming. In this paper, we consider mmWave wireless systems comprising of nodes equipped with large ant…
Characterization of the millimeter wave wireless channel is needed to facilitate fully connected vehicular communication in the future. To study the multipath-rich, rapidly varying nature of the vehicular propagation environment, fast millimeter wave channel sounders are required. We present a channel sounder design capable of covering 360 degrees in azimuth and 60 degrees in elevation with 200 individual beam directions in 6.25 ms by using four phased arrays simultaneously. The channel measurements are accompanied by high resolution positioning and video data, allowing channel sounding to be …
The performance of millimeter wave (mmWave) multiple-input multiple-output (MIMO) systems is limited by the sparse nature of propagation channels and the restricted number of radio frequency (RF) chains at transceivers. The introduction of reconfigurable antennas offers an additional degree of freedom on designing mmWave MIMO systems. This paper provides a theoretical framework for studying the mmWave MIMO with reconfigurable antennas. Based on the virtual channel model, we present an architecture of reconfigurable mmWave MIMO with beamspace hybrid analog-digital beamformers and reconfigurable…
This paper is concerned with spatial multiplexing analysis for millimeter-wave (mmWave) massive MIMO systems. For a single-user mmWave system employing distributed antenna subarray architecture in which the transmitter and receiver consist of Kt and Kr subarrays, respectively, an asymptotic multiplexing gain formula is firstly derived when the numbers of antennas at subarrays go to infinity. Specifically, assuming that all subchannels have the same average number of propagation paths L, the formula implies that by employing such a distributed antenna-subarray architecture, an exact average max…
This paper presents LuMaMi28, a real-time 28 GHz massive multiple-input multiple-output (MIMO) testbed. In this testbed, the base station has 16 transceiver chains with a fully-digital beamforming architecture (with different pre-coding algorithms) and simultaneously supports multiple user equipments (UEs) with spatial multiplexing. The UEs are equipped with a beam-switchable antenna array for real-time antenna selection where the one with the highest channel magnitude, out of four pre-defined beams, is selected. For the beam-switchable antenna array, we consider two kinds of UE antennas, with…
In this paper, we study two novel massive multiple-input multiple-output (MIMO) transmitter architectures for millimeter wave (mmWave) communications which comprise few active antennas, each equipped with a dedicated radio frequency (RF) chain, that illuminate a nearby large intelligent reflecting/transmitting surface (IRS/ITS). The IRS (ITS) consists of a large number of low-cost and energy-efficient passive antenna elements which are able to reflect (transmit) a phase-shifted version of the incident electromagnetic field. Similar to lens array (LA) antennas, IRS/ITS-aided antenna architectur…
Millimeter-wave (mmWave) communication and network densification hold great promise for achieving high-rate communication in next-generation wireless networks. Cloud radio access network (CRAN), in which low-complexity remote radio heads (RRHs) coordinated by a central unit (CU) are deployed to serve users in a distributed manner, is a cost-effective solution to achieve network densification. However, when operating over a large bandwidth in the mmWave frequencies, the digital fronthaul links in a CRAN would be easily saturated by the large amount of sampled and quantized signals to be transfe…
This paper presents a 3-D statistical channel model of the impulse response with small-scale spatially correlated random coefficients for multi-element transmitter and receiver antenna arrays, derived using the physically-based time cluster - spatial lobe (TCSL) clustering scheme. The small-scale properties of multipath amplitudes are modeled based on 28 GHz outdoor millimeter-wave small-scale local area channel measurements. The wideband channel capacity is evaluated by considering measurement-based Rician-distributed voltage amplitudes, and the spatial autocorrelation of multipath amplitudes…
Rapidly fading channels caused by pedestrians in dense urban environments will have a significant impact on millimeter-wave (mmWave) communications systems that employ electrically-steerable and narrow beamwidth antenna arrays. A peer-to-peer (P2P) measurement campaign was conducted with 7-degree, 15-degree, and 60-degree half-power beamwidth (HPBW) antenna pairs at 73.5 GHz and with 1 GHz of RF null-to-null bandwidth in a heavily populated open square scenario in Brooklyn, New York, to study blockage events caused by typical pedestrian traffic. Antenna beamwidths that range approximately an o…
In this paper we carry out the asymptotic diversity analysis for millimeter-wave (mmWave) massive multiple-input multiple-output (MIMO) systems by using bit interleaved coded multiple beamforming (BICMB). First, a single-user mmWave system which employs $M_t$ antenna subarrays at the transmitter and $M_r$ antenna subarrays at the receiver is studied. Each antenna subarray in the transmitter and the receiver has $N_r$ and $N_t$ antennas, respectively. We establish a theorem for the diversity gain when the number of antennas in each remote antenna unit (RAU) goes to infinity. Based on the theore…
We analyze the diversity gain for a distributed antenna subarray employing orthogonal frequency-division multiplexing (OFDM) in millimeter-wave (mm-Wave) massive multiple-input multiple-output (MIMO) systems. We show that the diversity gain depends on the number of transmitted data streams, the number of remote antenna units, and the number of propagation paths between RAUs. Furthermore, we show that by using bit-interleaved coded multiple beamforming (BICMB), one can achieve the maximum diversity gain in a distributed antenna subarray system. The assumption in both scenarios is that the numbe…
Millimeter-wave massive MIMO with lens antenna array can considerably reduce the number of required radio-frequency (RF) chains by beam selection. However, beam selection requires the base station to acquire the accurate information of beamspace channel. This is a challenging task, as the size of beamspace channel is large while the number of RF chains is limited. In this paper, we investigate the beamspace channel estimation problem in mmWave massive MIMO systems with lens antenna array. Specifically, we first design an adaptive selecting network for mmWave massive MIMO systems with lens ante…
Millimeter-wave links are of a line-of-sight nature. Hence, multiple-input multiple-output (MIMO) systems operating in the millimeter-wave band may not achieve full spatial diversity or multiplexing. In this paper, we utilize reconfigurable antennas and the high antenna directivity in the millimeter-wave band to propose a rate-two space coding design for 2x2 MIMO systems. The proposed scheme can be decoded with a low complexity maximum-likelihood detector at the receiver and yet it can enhance the bit-error-rate performance of millimeter-wave systems compared to traditional spatial multiplexin…
The use of the millimeter (mm) wave spectrum for next generation (5G) mobile communication has gained significant attention recently. The small carrier wavelengths at mmwave frequencies enable synthesis of compact antenna arrays, providing beamforming gains that compensate the increased propagation losses. In this work, we investigate the feasibility of employing multiple antenna arrays to obtain diversity/multiplexing gains in mmwave systems, where each of the arrays is capable of beamforming independently. Considering a codebook based beamforming system (e.g., to facilitate limited feedback)…
The millimeter wave (mmWave) band, which is a prime candidate for 5G cellular networks, seems attractive for wireless energy harvesting. This is because it will feature large antenna arrays as well as extremely dense base station (BS) deployments. The viability of mmWave for energy harvesting though is unclear, due to the differences in propagation characteristics such as extreme sensitivity to building blockages. This paper considers a scenario where low-power devices extract energy and/or information from the mmWave signals. Using stochastic geometry, analytical expressions are derived for t…
This paper presents 73 GHz wideband outdoor foliage and ground reflection measurements. Propagation measurements were made with a 400 Megachip-per-second sliding correlator channel sounder, with rotatable 27 dBi (7 degrees half- power beamwidth) horn antennas at both the transmitter and receiver, to study foliage-induced scattering and de-polarization effects, to assist in developing future wireless systems that will use adaptive array antennas. Signal attenuation through foliage was measured to be 0.4 dB/m for both co- and cross-polarized antenna configurations. Measured ground reflection coe…
Fifth generation (5G) wireless networks are expected to utilize wide bandwidths available at millimeter wave (mmWave) frequencies for enhancing system throughput. However, the unfavorable channel conditions of mmWave links, e.g., higher path loss and attenuation due to atmospheric gases or water vapor, hinder reliable communications. To compensate for these severe losses, it is essential to have a multitude of antennas to generate sharp and strong beams for directional transmission. In this paper, we consider mmWave systems using uniform planar array (UPA) antennas, which effectively place mor…
By employing the lens antenna array, beamspace MIMO can utilize beam selection to reduce the number of required RF chains in mmWave massive MIMO systems without obvious performance loss. However, to achieve the capacityapproaching performance, beam selection requires the accurate information of beamspace channel of large size, which is challenging, especially when the number of RF chains is limited. To solve this problem, in this paper we propose a reliable support detection (SD)-based channel estimation scheme. Specifically, we propose to decompose the total beamspace channel estimation probl…
This paper presents directional and omnidirectional RMS delay spread statistics obtained from 28 GHz and 73 GHz ultrawideband propagation measurements carried out in New York City using a 400 Megachips per second broadband sliding correlator channel sounder and highly directional steerable horn antennas. The 28 GHz measurements did not systematically seek the optimum antenna pointing angles and resulted in 33% outage for 39 T-R separation distances within 200 m. The 73 GHz measurements systematically found the best antenna pointing angles and resulted in 14.3% outage for 35 T-R separation dist…
Millimeter-wave (mmWave) communication systems rely on large-scale antenna arrays to combat large path-loss at mmWave band. Due to hardware characteristics and deployment environments, mmWave large-scale antenna systems are vulnerable to antenna element blockages and failures, which necessitate diagnostic techniques to locate faulty antenna elements for calibration purposes. Current diagnostic techniques require full or partial knowledge of channel state information (CSI), which can be challenging to acquire in the presence of antenna failures. In this letter, we propose a blind diagnostic tec…
Emerging applications involving device-to-device communication among wearable electronics require Gbps throughput, which can be achieved by utilizing millimeter wave (mmWave) frequency bands. When many such communicating devices are indoors in close proximity, like in a train car or airplane cabin, interference can be a serious impairment. This paper uses stochastic geometry to analyze the performance of mmWave networks with a finite number of interferers in a finite network region. Prior work considered either lower carrier frequencies with different antenna and channel assumptions, or a netw…
Millimeter wave (mmWave) communication by utilizing lens antenna arrays is a promising technique for realizing cost-effective 5G wireless systems with large MIMO (multiple-input multiple-output) but only limited radio frequency (RF) chains. This paper studies an uplink multi-user mmWave single-sided lens MIMO system, where only the base station (BS) is equipped with a full-dimensional (FD) lens antenna array with both elevation and azimuth angle resolution capabilities, and each mobile station (MS) employs the conventional uniform planar array (UPA) without the lens. By exploiting the angle-de…
Wireless networks with directional antennas, like millimeter wave (mmWave) networks, have enhanced security. For a large-scale mmWave ad hoc network in which eavesdroppers are randomly located, however, eavesdroppers can still intercept the confidential messages, since they may reside in the signal beam. This paper explores the potential of physical layer security in mmWave ad hoc networks. Specifically, we characterize the impact of mmWave channel characteristics, random blockages, and antenna gains on the secrecy performance. For the special case of uniform linear array (ULA), a tractable ap…
Millimeter wave signals and large antenna arrays are considered enabling technologies for future 5G networks. Despite their benefits for achieving high data rate communications, their potential advantages for tracking of the location of the user terminals are largely undiscovered. In this paper, we propose a novel support detection-based channel training method for frequency selective millimeter-wave (mm-wave) multiple-input-multiple-output system with lens antenna arrays. We show that accurate position and orientation estimation and tracking is possible using signals from a single transmitter…
The emerging millimeter-wave (mmWave) massive multiple-input multiple-output (MIMO) with lens antenna arrays, which is also known as "beamspace MIMO", can effectively reduce the required number of power-hungry radio frequency (RF) chains. Therefore, it has been considered as a promising technique for the upcoming 5G communications and beyond. However, most current studies on beamspace MIMO have not taken into account the important power leakage problem in beamspace channels, which possibly leads to a significant degradation in the signal-to-noise ratio (SNR) and the system sum-rate. To this en…
In millimeter-wave communications (MMWC), in order to compensate for high propagation attenuation, phased arrays are favored to achieve array gain by beamforming, where transmitting and receiving antenna arrays need to be jointly trained to obtain appropriate antenna weight vectors (AWVs). Since the amplitude of each element of the AWV is usually constraint constant to simplify the design of phased arrays in MMWC, the existing singular vector based beamforming training scheme cannot be used for such devices. Thus, in this letter, a steering vector based iterative beamforming training scheme, w…
Millimeter-wave (mmWave) systems use directional beams to support high-rate data communications. Small misalignment between the transmit and receive beams (e.g., due to the mobility) can result in significant drop of the received signal quality especially in line-of-sight communication channels. In this paper, we propose and evaluate high-resolution angle tracking strategies for wideband mmWave systems with mobility. We custom design pairs of auxiliary beams as the tracking beams, and use them to capture the angle variations, towards which the steering directions of the data beams are adjusted…
This work analyzes a mmWave single-cell network, which comprises a macro base station (BS) and an overlaid tier of small-cell BSs using a wireless backhaul for data traffic. We look for the optimal number of antennas at both BS and small-cell BSs that maximize the energy efficiency (EE) of the system when a hybrid transceiver architecture is employed. Closed-form expressions for the EE-optimal values of the number of antennas are derived that provide valuable insights into the interplay between the optimization variables and hardware characteristics. Numerical and analytical results show that …
The aim of antenna array synthesis is to achieve a desired radiation pattern with the minimum number of antenna elements. In this paper the antenna synthesis problem is studied from a totally new perspective. One of the key principles of compressive sensing is that the signal to be sensed should be sparse or compressible. This coincides with the requirement of minimum number of element in the antenna array synthesis problem. In this paper the antenna element of the array can be efficiently reduced via compressive sensing, which shows a great improvement to the existing antenna synthesis method…
This paper presents outdoor wideband small-scale spatial fading and autocorrelation measurements and results in the 73 GHz millimeter-wave (mmWave) band conducted in downtown Brooklyn, New York. Both directional and omnidirectional receiver (RX) antennas are studied. Two pairs of transmitter (TX) and RX locations were tested with one line-of-sight (LOS) and one non-line-of-sight (NLOS) environment, where a linear track was employed at each RX to move the antenna in half-wavelength increments. Measured data reveal that the small-scale spatial fading of the received signal voltage amplitude are …
In this paper, randomly-directional beamforming (RDB) is considered for millimeter-wave (mmwave) multi-user (MU) multiple-input single-output (MISO) downlink systems. By using asymptotic techniques, the performance of RDB and the MU gain in mm-wave MISO are analyzed based on the uniform random line-of-sight (UR-LoS) channel model suitable for highly directional mm-wave radio propagation channels. It is shown that there exists a transition point on the number of users relative to the number of antenna elements for non-trivial performance of the RDB scheme, and furthermore sum rate scaling arbit…
Millimeter wave (mmWave) communications which essentially employ directional antennas find applications spanning from indoor short range wireless personal area networks to outdoor cellular networks. A thorough understanding of mmWave signal propagation through the wireless channel provides valuable insights for the design of such networks which in turn dictates the achievable performance limits. High path loss, penetration loss, and negligible signal scattering are certain distinctive features of the mmWave channel which necessitates the development of new mathematical models. Importantly, the…
In this paper we study the maximum throughput achievable with optimal scheduling in multi-hop networks with highly directive antenna arrays capable of Space Division Multiplexing (SDM) at the transmitter and Space Division Multiple Access (SDMA) at the receiver. This network model is relevant for future millimeter wave (mmWave) systems, which are expected to implement self-backhauled cellular networks with very high data rates, relying on carrier frequencies between 10-300 GHz, channels with a very large bandwidth, and a large number of antenna elements, even in mobile devices. We adapt mmWave…
An intelligent reflecting surface (IRS)-assisted millimeter-wave (mmWave) massive multiple input multiple output (MIMO) system with transmit antenna selection (TAS) using orthogonal space-time block codes (OSTBC) scheme is proposed in this paper. This system combines TAS and IRS with hybrid analog-digital beamforming (HBF) for 60 GHz mmWave communications in order to exploit the benefits of TAS, OSTBC, analog beamforming (ABF), and transmit digital precoding techniques. The proposed system, however, benefits from the transmit diversity gain of OSTBC scheme as well as from the signal-to-noise r…
Massive MIMO systems with uniform circular and cylindrical antenna arrays are studied. Favorable propagation property is rigorously shown to hold asymptotically in LOS environment for a fixed antenna spacing and under some mild conditions. The analysis is based on a novel method using a Bessel function expansion, a new bounding technique and a simplified representation of inter-user interference for array geometries obeying Kronecker structure.
Beamforming is an indispensable feature for millimeter wave (mmWave) wireless communications in order to compensate for the severe path loss incurred due to high frequency operation. In this paper, we introduce a novel framework to evaluate the spectral efficiency (SE) of non-line-of-sight(NLOS) mmWave links with optimal analog beamforming. Optimality here implies the joint selection of antenna beams at the transmitter and receiver which simultaneously maximize the received power. We develop a mathematical framework based on the extended Saleh-Valenzuela channel model to embody the impact of o…
This paper investigates the hybrid precoding design for millimeter wave (mmWave) multiple-input multiple-output (MIMO) systems with finite-alphabet inputs. The mmWave MIMO system employs partially-connected hybrid precoding architecture with dynamic subarrays, where each radio frequency (RF) chain is connected to a dynamic subset of antennas. We consider the design of analog and digital precoders utilizing statistical and/or mixed channel state information (CSI), which involve solving an extremely difficult problem in theory: First, designing the optimal partition of antennas over RF chains is…
This paper describes wideband (1 GHz) base station diversity and coordinated multipoint (CoMP)-style large-scale measurements at 73 GHz in an urban microcell open square scenario in downtown Brooklyn, New York on the NYU campus. The measurements consisted of ten random receiver locations at pedestrian level (1.4 meters) and ten random transmitter locations at lamppost level (4.0 meters) that provided 36 individual transmitter-receiver (TX-RX) combinations. For each of the 36 radio links, extensive directional measurements were made to give insights into small-cell base station diversity at mil…
