In this paper, we investigate the optimization problem of joint source and relay beamforming matrices for a twoway amplify-and-forward (AF) multi-input multi-output (MIMO) relay system. The system consisting of two source nodes and two relay nodes is considered and the linear minimum meansquare- error (MMSE) is employed at both receivers. We assume individual relay power constraints and study an important design problem, a so-called determinant maximization (DM) problem. Since this DM problem is nonconvex, we consider an efficient iterative algorithm by using an MSE balancing result to obtain at least a locally optimal solution. The proposed algorithm is developed based on QL, QR and Choleskey decompositions which differ in the complexity and performance. Analytical and simulation results show that the proposed algorithm can significantly reduce computational complexity compared with their existing two-way relay systems and have equivalent bit-error-rate (BER) performance to the singular value decomposition (SVD) based on a regular block diagonal (RBD) scheme.
In this paper, collaborative use of relays to form a beamforming system and provide physical-layer security is investigated. In particular, amplify-and-forward (AF) relay beamforming designs under total and individual relay power constraints are studied with the goal of maximizing the secrecy rates when perfect channel state information (CSI) is available. In the AF scheme, not having analytical solutions for the optimal beamforming design under both total and individual power constraints, an iterative algorithm is proposed to numerically obtain the optimal beamforming structure and maximize t…
In this paper, we propose a full-duplex relay (FDR) based on a zero-forcing beamforming (ZFBF) for a multiuser MIMO relay system. The ZFBF is employed at the base station to suppress both the self-interference of the relay and the multiuser interference at the same time. Numerical results show that the proposed FDR can enhance the sum rate performance as compared to the half-duplex relay (HDR), if sufficient isolation between the transmit and receive antennas is ensured at the relay.
This paper deals with distributed beamforming techniques for wireless networks with half-duplex amplify-and-forward relays. Existing schemes optimize the beamforming weights based on the assumption that channel state information (CSI) is available at the relays. We propose to use adaptive beamforming based on deterministic perturbations and limited feedback (1-bit) from the destination to the relays in order to avoid CSI at the relays. Two scalable perturbation schemes are considered and practical implementation aspects are addressed. Simulation results confirm that the proposed techniques clo…
In this paper, a cognitive relay channel is considered, and amplify-and-forward (AF) relay beamforming designs in the presence of an eavesdropper and a primary user are studied. Our objective is to optimize the performance of the cognitive relay beamforming system while limiting the interference in the direction of the primary receiver and keeping the transmitted signal secret from the eavesdropper. We show that under both total and individual power constraints, the problem becomes a quasiconvex optimization problem which can be solved by interior point methods. We also propose two sub-optimal…
This paper presents joint maximum signal-to-interference-plus-noise ratio (MSINR) and relay selection algorithms for distributed beamforming. We propose a joint MSINR and restricted greedy search relay selection (RGSRS) algorithm with a total relay transmit power constraint that iteratively optimizes both the beamforming weights at the relays nodes, maximizing the SINR at the destination. Specifically, we devise a relay selection scheme that based on greedy search and compare it to other schemes like restricted random relay selection (RRRS) and restricted exhaustive search relay selection (RES…
A full-duplex two-way relay channel with multiple antennas is considered. For this three-node network, the beamforming design needs to suppress self-interference. While a traditional way is to apply zero-forcing for self-interference mitigation, it may harm the desired signals. In this paper, a design which reserves a fraction of self-interference is proposed by solving a quality-of-service constrained beamforming design problem. Since the problem is challenging due to the loop self-interference, a convergence-guaranteed alternating optimization algorithm is proposed to jointly design the rela…
In this paper, collaborative use of relays to form a beamforming system and provide physical-layer security is investigated. In particular, decode-and-forward (DF) and amplify-and-forward (AF) relay beamforming designs under total and individual relay power constraints are studied with the goal of maximizing the secrecy rates when perfect channel state information (CSI) is available. In the DF scheme, the total power constraint leads to a closed-form solution, and in this case, the optimal beamforming structure is identified in the low and high signal-to-noise ratio (SNR) regimes. The beamform…
We reduce the problem of optimal beamforming for two-way relay (TWR) systems with perfect channel state infomation (CSI) that use analog network coding (ANC) to a pair of algebraic equations in two variables that can be solved inexpensively using numerical methods. The solution has greatly reduced complexity compared to previous exact solutions via semidefinite programming (SDP). Together with the linearized robust solution described in (Aziz and Thron, 2014), it provides a high-performance, low-complexity robust beamforming solution for 2-way relays.
In this paper, collaborative use of relays to form a beamforming system with the aid of perfect channel state information (CSI) and to provide physical-layer security is investigated. In particular, a decode-and-forward-based relay beamforming design subject to total and individual relay power constraints is studied with the goal of maximizing the secrecy rate. It is shown that the total power constraint leads to a closed-form solution. The design under individual relay power constraints is formulated as an optimization problem which is shown to be easily solved using two different approaches,…
In this paper, collaborative use of relays to form a beamforming system with the aid of perfect channel state information (CSI) and to provide communication in physicallayer security between a transmitter and two receivers is investigated. In particular, we describe decode-and-forward based null space beamforming schemes and optimize the relay weights jointly to obtain the largest secrecy rate region. Furthermore, the optimality of the proposed schemes is investigated by comparing them with the outer bound secrecy rate region
We consider the full-duplex (FD) two-way amplify-and-forward relay system with imperfect cancelation of loopback self-interference (SI) and investigate joint design of relay and receive beamforming for minimizing the mean square error under a relay transmit power constraint. Due to loopback channel estimation error and limitation of analog-to-digital converter, the loopback SI cannot be completely canceled. Multiple antennas at the relay can help loopback SI suppression but beamforming is required to balance between the residual SI suppression and the desired signal transmission. Moreover, the…
In this paper, we consider the transceiver and relay design for multiple-input multiple-output (MIMO) cellular two-way relay channel (cTWRC), where a multi-antenna base station (BS) exchanges information with multiple multi-antenna mobile stations via a multi-antenna relay station (RS). We propose a novel two-way relaying scheme to approach the sum capacity of the MIMO cTWRC.
A two-phase beamforming solution for secure communication using untrusted relay nodes is presented. To thwart eavesdropping attempts of relay nodes, we deliberately introduce artificial noise in the source message. After pointing out the incongruity in evaluating secrecy rate in our model for certain scenarios, we provide an SNR based frame work for secure communication. We intend to bring down the SNR at each of the untrusted relay nodes below a certain predefined threshold, whereas, using beamforming we want to boost the SNR at the destination. With this motive optimal scaling vector is eval…
Consider a simple two-way relaying channel where two single-antenna sources exchange information via a multiple-antenna relay. To such a scenario, all the existing works which can achieve full diversity order are based on the antenna/relay selection, where the difficulty to design the beamforming lies in the fact that a single beamformer needs to serve two destinations. In this paper, we propose a new full-diversity beamforming scheme which ensures that the relay signals are coherently combined at both destinations. Both analytical and numerical results are provided to demonstrate that this pr…
In this paper, the filter-and-forward (FF) relay design for multiple-input multiple-output (MIMO) orthogonal frequency-division multiplexing (OFDM) systems is considered. Due to the considered MIMO structure, the problem of joint design of the linear MIMO transceiver at the source and the destination and the FF relay at the relay is considered. As the design criterion, the minimization of weighted sum mean-square-error (MSE) is considered first, and the joint design in this case is approached based on alternating optimization that iterates between optimal design of the FF relay for a given set…
We investigate a relay network where a multiantenna source can potentially utilize an unauthenticated (untrusted) relay to augment its direct transmission of a confidential message to the destination. Since the relay is untrusted, it is desirable to protect the confidential data from it while simultaneously making use of it to increase the reliability of the transmission. We present a low-complexity scheme denoted as imbalanced beamforming based on linear beamforming and constellation mapping that ensures perfect physical-layer security even while utilizing the untrusted relay. Furthermore, th…
This paper considers the multi-input multi-output (MIMO) relay channel where multiple antennas are employed by each terminal. Compared to single-input single-output (SISO) relay channels, MIMO relay channels introduce additional degrees of freedom, making the design and analysis of optimal cooperative strategies more complex. In this paper, a partial cooperation strategy that combines transmit-side message splitting and block-Markov encoding is presented. Lower bounds on capacity that improve on a previously proposed non-cooperative lower bound are derived for Gaussian MIMO relay channels.
We consider a two-way relay network, where two source nodes, S1 and S2, exchange information through a cluster of relay nodes. The relay nodes receive the sum signal from S1 and S2 in the first time slot. In the second time slot, each relay node multiplies its received signal by a complex coefficient and retransmits the signal to the two source nodes, which leads to a distributed two-way beamforming system. By applying the principle of analog network coding, each receiver at S1 and S2 cancels the ``self-interference'' in the received signal from the relay cluster and decodes the message. This …
In this correspondence, we consider an amplify-and-forward relay network in which relayed information is overheard by an eavesdropper. In order to confound the eavesdropper, a wireless-powered jammer is also considered which harvests energy from a multiple-antenna source. We proposed a new secure beamforming scheme in which beamforming vector is a linear combination of the energy beamforming (EB) and information beamforming (IB) vectors. We also present a new closed-form solution for the proposed beamforming vector which is shown to achieve a higher secrecy rate as compared to the trivial EB a…
We consider a two-way relay network, where two source nodes, S1 and S2, exchange information through a cluster of relay nodes. The relay nodes receive the sum signal from S1 and S2 in the first time slot. In the second time slot, each relay node multiplies its received signal by a complex coefficient and retransmits the signal to the two source nodes, which leads to a collaborative two-way beamforming system. By applying the principle of analog network coding, each receiver at S1 and S2 cancels the "self-interference" in the received signal from the relay cluster and decodes the message. This …
In this paper, we investigate the problem of two-way relay beamforming optimization to maximize the achievable sum-rate of a simultaneous wireless information and power transfer (SWIPT) system with a full-duplex (FD) multiple-input multiple-output (MIMO) amplify-and-forward (AF) relay. In particular, we address the optimal joint design of the receiver power splitting (PS) ratio and the beamforming matrix at the relay node given the channel state information (CSI). Our contribution is an iterative algorithm based on difference of convex (DC) programming and one-dimensional searching to achieve …
In this paper, link selection for half-duplex buffer-aided relay systems is revisited. A new fixed scheduling policy referred as alternate distributed beamforming (ADB) is proposed, in which the relays are divided into two groups, with one group receiving the same information broadcast from the source and the other group transmitting the common messages to the destination via distributed beamforming in each time slot. It is worth noting that the relays used for reception and transmission are determined without the need of instantaneous channel state information (CSI). Theoretical analysis of t…
A multiple input multiple output (MIMO) two-way relay channel is considered, where two sources want to exchange messages with each other using multiple relay nodes, and both the sources and relay nodes are equipped with multiple antennas. Both the sources are assumed to have equal number of antennas and have perfect channel state information (CSI) for all the channels of the MIMO two-way relay channel, whereas, each relay node is either assumed to have CSI for its transmit and receive channel (the coherent case) or no CSI for any of the channels (the non-coherent case). The main results in thi…
We consider a multi-pair two-way amplify-and-forward massive multi-input multi-output (MIMO) hybrid relay with MIMO user-pairs. A hybrid relay has lesser number of radio frequency (RF) chains than the antennas, which significantly reduces the implementation cost. We employ block-diagonalization-based baseband processing at the hybrid relay to cancel the inter user-pair interference and equal-gain-combining-based RF processing to maximize the beamforming gain. We also use an algebraic norm maximizing relay transmit strategy to maximize the spectral efficiency (SE) of each user-pair. We numerica…
This is a companion technical report of the main manuscript "Semidefinite Relaxation and Approximation Analysis of a Beamformed Alamouti Scheme for Relay Beamforming Networks". The report serves to give detailed derivations of Lemma 1-2 in the main manuscript, which are too long to be included in the latter. In addition, more simulation results are presented to verify the viability of the BF Alamouti AF schemes developed in the main manuscript.
We derive optimal SNR-based transmit antenna selection rules at the source and relay for the nonregenerative half duplex MIMO relay channel. While antenna selection is a suboptimal form of beamforming, it has the advantage that the optimization is tractable and can be implemented with only a few bits of feedback from the destination to the source and relay. We compare the bit error rate of optimal antenna selection at both the source and relay to other proposed beamforming techniques and propose methods for performing the necessary limited feedback.
In this paper, we study the energy efficiency (EE) maximization problem in multiple-input multiple-output (MIMO) two-way relay networks with simultaneous wireless information and power transfer (SWIPT). The network consists of a multiple-antenna amplify-and-forward relay node which provides bidirectional communications between two multiple-antenna transceiver nodes
In this paper we study and analyze coverage region for half-duplex multiple-input multiple-output (MIMO) relay channel with amplify-and-forward (AF) strategy at the relay station. By assuming mixed Rayleigh and Rician fading channels with two different relay station situations, we consider the objective of maximizing coverage region for a given transmission rate and find the optimal relay location in the sense of maximizing coverage region. using Monte Carlo simulations, the coverage region and capacity bounds are shown for different fading cases and different relay station locations. Finally,…
In this paper, linear beamforming design for amplify-and-forward relaying cellular networks is considered, in which base station, relay station and mobile terminals are all equipped with multiple antennas. The design is based on minimum mean-square-error criterion, and both uplink and downlink scenarios are considered. It is found that the downlink and uplink beamforming design problems are in the same form, and iterative algorithms with the same structure can be used to solve the design problems. For the specific cases of fully loaded or overloaded uplink systems, a novel algorithm is derived…
This paper studies simultaneous wireless information and power transfer (SWIPT) systems in two-way relaying (TWR) channels. Here, two source nodes receive information and energy simultaneously via power splitting (PS) from the signals sent by a multi-antenna relay node. Our objective is to maximize the weighted sum of the harvested energy at two source nodes subject to quality of service (QoS) constraints and the relay power constraints. Three well-known and practical two-way relay strategies are considered, i.e., amplify-and-forward (AF), bit level XOR based decode-and-forward (DF-XOR) and sy…
Relay selection enhances the performance of the cooperative networks by selecting the links with higher capacity. Meanwhile link adaptation improves the spectral efficiency of wireless data-centric networks through adapting the modulation and coding schemes (MCS) to the current link condition. In this paper, relay selection is combined with link adaptation for distributed beamforming in a two-hop regenerative cooperative system. A novel signaling mechanism and related optimal algorithms are proposed for joint relay selection and link adaptation. In the proposed scheme, there is no need to feed…
We study and analyze coverage region in MIMO communication systems for a multiple-relay network with decode-and-forward (DF) strategy at the relays. Assuming that there is a line-of-sight (LOS) propagation environment for source-relay channels and channel state information is available at receivers (CSIR), we consider the objective of maximizing coverage region for a given transmission rate and show numerically the significant effect of propagation environment on capacity bounds, optimal relay location and coverage region. Also, we study the situation in which two adjacent relays cooperate in …
In this work, we maximize the secrecy rate of the wireless-powered untrusted relay network by jointly designing power splitting (PS) ratio and relay beamforming with the proposed global optimal algorithm (GOA) and local optimal algorithm (LOA). Different from the literature, artificial noise (AN) sent by the destination not only degrades the channel condition of the eavesdropper to improve the secrecy rate, but also becomes a new source of energy powering the untrusted relay based on PS. Hence, it is of high economic benefits and efficiency to take advantage of AN compared with the literature.…
This paper studies the wireless two-way relay channel (TWRC), where two source nodes, S1 and S2, exchange information through an assisting relay node, R. It is assumed that R receives the sum signal from S1 and S2 in one time-slot, and then amplifies and forwards the received signal to both S1 and S2 in the next time-slot. By applying the principle of analogue network (ANC), each of S1 and S2 cancels the so-called "self-interference" in the received signal from R and then decodes the desired message. Assuming that S1 and S2 are each equipped with a single antenna and R with multi-antennas, thi…
This paper proposed new hybrid, analog-digital, beamforming for a multiuser millimeter wave (mm-wave) relay system. For this system, we consider a sum rate maximization problem. The proposed hybrid beamforming is designed indirectly by considering a sum mean square error (MSE) minimization problem while utilizing the solution of digital beamforming. To this end, we assume that the digital beamforming utilizes the well known block diagonalization (BD) approach. Under this assumption, we solve our problem as follows: First, we formulate the sum rate maximization problem as the minimization of th…
In this paper, the robust distributed relay beamforming problem is solved using the worst case approach, where the problem solution has been involved because of the effect of uncertainty of channel knowledge on the quality of service (QoS) constraints. It is shown that the original robust design, which is a non-convex semi-infinite problem (SIP), can be relaxed and reformed to a semi-definite problem (SDP). Monte-Carlo simulations are presented to verify the performance improvement of our proposed robust problem over existing robust and non-robust problems in terms of transmit power and symbol…
In this work, we study the problem of relay beamforming for an underlay cognitive radio relay network using amplify-and-forward (AF) relaying technique. We consider a cognitive radio network consisting of single primary and multiple secondary transmitters/receivers. In addition, there are several relay nodes that help both primary and secondary networks. We propose a new beamforming method for relays' transmission, in which the beamforming weights at the relays are the solution of an optimization problem. The objective of the optimization problem is maximizing the worst case signal to interfer…
In this paper, we study the performance of the downlink of a cellular network with automatic repeat-request (ARQ) and a half duplex decode-and-forward shared relay. In this system, two multiple-input-multiple-output (MIMO) base stations serve two single antenna users. A MIMO shared relay retransmits the lost packets to the target users. First, we study the system with direct retransmission from the base station and derive a closed form expression for the outage probability of the system.We show that the direct retransmission can overcome the fading, however, it cannot overcome the interference…
In this paper, we address the problem of optimal power allocation at the relay in two-hop secure communications under practical conditions. To guarantee secure communication during the long-distance transmission, the massive MIMO (M-MIMO) relaying techniques are explored to significantly enhance wireless security. The focus of this paper is on the analysis and design of optimal power assignment for a decode-and-forward (DF) M-MIMO relay, so as to maximize the secrecy outage capacity and minimize the interception probability, respectively. Our study reveals the condition for a nonnegative the s…
This paper studies the secure beamforming design in a multiple-antenna three-node system where two source nodes exchange messages with the help of an untrusted relay node. The relay acts as both an essential signal forwarder and a potential eavesdropper. Both two-phase and three-phase two-way relay strategies are considered. Our goal is to jointly optimize the source and relay beamformers for maximizing the secrecy sum rate of the two-way communications. We first derive the optimal relay beamformer structures. Then, iterative algorithms are proposed to find source and relay beamformers jointly…
This letter considers simultaneous wireless information and power transfer (SWIPT) for a multiple-input multiple-output (MIMO) relay system. The relay is powered by harvesting energy from the source via time switching (TS) and utilizes the harvested energy to forward the information signal. Our aim is to maximize the rate of the system subject to the power constraints at both the source and relay nodes. In the first scenario in which the source covariance matrix is an identity matrix, we present the joint-optimal solution for relaying and the TS ratio in closed form. An iterative scheme is the…
This paper considers the partial decode-and-forward (PDF) strategy for the Gaussian multiple-input multiple-output (MIMO) relay channel. Unlike for the decode-and-forward (DF) strategy or point-to-point (P2P) transmission, for which Gaussian channel inputs are known to be optimal, the input distribution that maximizes the achievable PDF rate for the Gaussian MIMO relay channel has remained unknown so far. For some special cases, e.g., for relay channels where the optimal PDF strategy reduces to DF or P2P transmission, it could be deduced that Gaussian inputs maximize the PDF rate. For the gene…
In this paper, link selection is investigated in half-duplex (HD) dual-hop cooperative systems with multiple antennas at the relays. Alternate distributed beamforming (ADB) scheme is revisited for buffer-aided multi-antenna relay systems, in which the relays are divided into two groups, with one group receiving the same information broadcast from the source and the other group transmitting the common messages to the destination via distributed beamforming in each time slot. It is worth noting that the relays used for reception and transmission are determined without the need of instantaneous c…
Unified performance analysis is carried out for amplify-and-forward (AF) multiple-input-multiple-output (MIMO) beamforming (BF) two-way relay networks in Rayleigh fading with five different relaying protocols including two novel protocols for better performance. As a result, a novel closed-form sum-bit error rate (BER) expression is presented in a unified expression for all protocols. A new closed-form high signal-to-noise-ratio (SNR) performance is also obtained in a single expression, and an analytical high-SNR gap expression between the five protocols is provided. We compare the performance…
The deterministic capacity of a relay network is the capacity of a network when relays are restricted to transmitting \emph{reliable} information, that is, (asymptotically) deterministic function of the source message. In this paper it is shown that the deterministic capacity of a number of MIMO relay networks can be found in the low power regime where $\SNR\to0$. This is accomplished through deriving single letter upper bounds and finding the limit of these as $\SNR\to0$. The advantage of this technique is that it overcomes the difficulty of finding optimum distributions for mutual informatio…
We address the problem of a multi-user relay network, where multiple single-antenna node pairs want to exchange information by using a multiple antenna relay node. Due to the half-duplex constraint of the relay, the exchange of information takes place in two steps. In the first step, the nodes transmit their data to the relay, while in the second step, the relay is broadcasting the data by using linear and non-linear precoding strategies. We focus on the second step in this paper. We first consider the problem of maximizing the overall rate achievable using linear and dirty-paper type precodin…
The physical-layer security issue in the multiple non-regenerative wireless-powered relay (WPR) networks is investigated in this letter, where the idle relay is treated as a potential eavesdropper. To guarantee secure communication, the destination-based artificial noise is sent to degrade the receptions of eavesdroppers, and it also becomes a new source of energy powering relays to forward the information with power splitting (PS) technique. We propose an efficient algorithm ground on block-wise penalty function method to jointly optimize PS ratio and beamforming to maximize the secrecy rate.…
Beamforming is indispensable in the operation of 60-GHz millimeter-wave directional multi-gigabit Wi-Fi. Simple power method and its extensions enable the transmitting and receiving antenna arrays to form a beam for single spatial stream. To further improve the spectral efficiency in future 60-GHz directional Wi-Fi, alternating least square (ALS) algorithm can form multiple beams between the transmitter and receiver for multi-input-multi-output (MIMO) operations. For both shared and split MIMO architecture, the ALS beamforming algorithm can be operated in both frequency-flat and frequency-sele…
We consider two-way amplify and forward relaying, where multiple full-duplex user pairs exchange information via a shared full-duplex massive multiple-input multiple-output (MIMO) relay. We derive closed-form lower bound for the spectral efficiency with zero-forcing processing at the relay, by using minimum mean squared error channel estimation. The zero-forcing lower bound for the system model considered herein, which is valid for arbitrary number of antennas, is not yet derived in the massive MIMO relaying literature. We numerically demonstrate the accuracy of the derived lower bound and the…
This paper studies the achievable degrees of freedom for multi-user MIMO two-way relay channels, where there are $K$ source nodes, each equipped with $M$ antennas, one relay node, equipped with $N$ antennas, and each source node exchanges independent messages with an arbitrary set of other source nodes via the relay. By allowing an arbitrary information exchange pattern, the considered channel model is a unified one. It includes several existing channel models as special cases: $K$-user MIMO Y channel, multi-pair MIMO two-way relay channel, generalized MIMO two-way X relay channel, and $L$-clu…
In this study, energy-efficient deterministic adaptive beamforming algorithms are proposed for distributed sensor/relay networks. Specifically, DBSA, D-QESA, D-QESA-E, and a hybrid algorithm, hybrid-QESA, that combines the benefits of both deterministic and random adaptive beamforming algorithms, are proposed. Rigorous convergence analyses are provided for all our proposed algorithms and convergence to the global optimal solution is shown for all our proposed algorithms. Through extensive numerical simulations, we demonstrate that superior performance is achieved by our proposed DBSA and D-QES…
This paper studies a system where a set of $N$ relay nodes harvest energy from the signal received from a source to later utilize it when forwarding the source's data to a destination node via distributed beamforming. To this end, we derive (approximate) analytical expressions for the mean SNR at destination node when relays employ: i) time-switching based energy harvesting policy, ii) power-splitting based energy harvesting policy. The obtained results facilitate the study of the interplay between the energy harvesting parameters and the synchronization error, and their combined impact on mea…
In this paper, we study beamforming in decode-and-forward (DF) relaying using multiple relays, where the source node sends a secret message as well as a non-secret message to the destination node in the presence of multiple non-colluding eavesdroppers. The non-secret message is transmitted at a fixed rate $R_{0}$ and requires no protection from the eavesdroppers, whereas the secret message needs to be protected from the eavesdroppers. The source and relays operate under a total power constraint. We find the optimum source powers and weights of the relays for both secret and non-secret messages…
In this paper, we derive the optimal transmitter/ receiver beamforming vectors and relay weighting matrix for the multiple-input multiple-output amplify-and-forward relay channel. The analysis is accomplished in two steps. In the first step, the direct link between the transmitter (Tx) and receiver (Rx) is ignored and we show that the transmitter and the relay should map their signals to the strongest right singular vectors of the Tx-relay and relay-Rx channels. Based on the distributions of these vectors for independent identically distributed (i.i.d.) Rayleigh channels, the Grassmannian code…
In this paper, we deal with the performance analysis of full-duplex relaying in decode-&-forward cooperative networks with multiple-antenna terminals. More specifically, by analyzing the end-to-end statistics, we derive the accurate closed-form expressions of the end-to-end outage probability for both transmit and receive ZFBF scheme over Rayleigh fading environments. Some selected results show some interesting observations useful for system designers. Specifically, we observe that the outage performance can be improved by adopting the joint ZF-based precoding with different antenna configurat…
This paper considers the setup of a parallel MIMO relay network in which $K$ relays, each equipped with $N$ antennas, assist the transmitter and the receiver, each equipped with $M$ antennas, in the half-duplex mode, under the assumption that $N\geq{M}$. This setup has been studied in the literature like in \cite{nabar}, \cite{nabar2}, and \cite{qr}. In this paper, a simple scheme, the so-called Incremental Cooperative Beamforming, is introduced and shown to achieve the capacity of the network in the asymptotic case of $K\to{\infty}$ with a gap no more than $O(\frac{1}{\log(K)})$. This result …
We consider efficient communications over the multiple-input multiple-output (MIMO) multiway distributed relay channel (MDRC) with full data exchange, where each user, equipped with multiple antennas, broadcasts its message to all the other users via the help of a number of distributive relays. We propose a physical-layer network coding (PNC) based scheme involving linear precoding for channel alignment nested lattice coding for PNC, and lattice-based precoding for interference mitigation, We show that, with the proposed scheme, distributed relaying achieves the same sum-rate as cooperative re…
