This paper deals with distributed beamforming techniques for wireless networks with half-duplex amplify-and-forward relays. Existing schemes optimize the beamforming weights based on the assumption that channel state information (CSI) is available at the relays. We propose to use adaptive beamforming based on deterministic perturbations and limited feedback (1-bit) from the destination to the relays in order to avoid CSI at the relays. Two scalable perturbation schemes are considered and practical implementation aspects are addressed. Simulation results confirm that the proposed techniques closely approach optimum performance and have satisfactory tracking properties in time-varying environments.
In this paper, collaborative use of relays to form a beamforming system and provide physical-layer security is investigated. In particular, amplify-and-forward (AF) relay beamforming designs under total and individual relay power constraints are studied with the goal of maximizing the secrecy rates when perfect channel state information (CSI) is available. In the AF scheme, not having analytical solutions for the optimal beamforming design under both total and individual power constraints, an iterative algorithm is proposed to numerically obtain the optimal beamforming structure and maximize t…
In this paper, we propose a full-duplex relay (FDR) based on a zero-forcing beamforming (ZFBF) for a multiuser MIMO relay system. The ZFBF is employed at the base station to suppress both the self-interference of the relay and the multiuser interference at the same time. Numerical results show that the proposed FDR can enhance the sum rate performance as compared to the half-duplex relay (HDR), if sufficient isolation between the transmit and receive antennas is ensured at the relay.
In this paper, a cognitive relay channel is considered, and amplify-and-forward (AF) relay beamforming designs in the presence of an eavesdropper and a primary user are studied. Our objective is to optimize the performance of the cognitive relay beamforming system while limiting the interference in the direction of the primary receiver and keeping the transmitted signal secret from the eavesdropper. We show that under both total and individual power constraints, the problem becomes a quasiconvex optimization problem which can be solved by interior point methods. We also propose two sub-optimal…
This paper presents joint maximum signal-to-interference-plus-noise ratio (MSINR) and relay selection algorithms for distributed beamforming. We propose a joint MSINR and restricted greedy search relay selection (RGSRS) algorithm with a total relay transmit power constraint that iteratively optimizes both the beamforming weights at the relays nodes, maximizing the SINR at the destination. Specifically, we devise a relay selection scheme that based on greedy search and compare it to other schemes like restricted random relay selection (RRRS) and restricted exhaustive search relay selection (RES…
A full-duplex two-way relay channel with multiple antennas is considered. For this three-node network, the beamforming design needs to suppress self-interference. While a traditional way is to apply zero-forcing for self-interference mitigation, it may harm the desired signals. In this paper, a design which reserves a fraction of self-interference is proposed by solving a quality-of-service constrained beamforming design problem. Since the problem is challenging due to the loop self-interference, a convergence-guaranteed alternating optimization algorithm is proposed to jointly design the rela…
In this paper, collaborative use of relays to form a beamforming system and provide physical-layer security is investigated. In particular, decode-and-forward (DF) and amplify-and-forward (AF) relay beamforming designs under total and individual relay power constraints are studied with the goal of maximizing the secrecy rates when perfect channel state information (CSI) is available. In the DF scheme, the total power constraint leads to a closed-form solution, and in this case, the optimal beamforming structure is identified in the low and high signal-to-noise ratio (SNR) regimes. The beamform…
We reduce the problem of optimal beamforming for two-way relay (TWR) systems with perfect channel state infomation (CSI) that use analog network coding (ANC) to a pair of algebraic equations in two variables that can be solved inexpensively using numerical methods. The solution has greatly reduced complexity compared to previous exact solutions via semidefinite programming (SDP). Together with the linearized robust solution described in (Aziz and Thron, 2014), it provides a high-performance, low-complexity robust beamforming solution for 2-way relays.
In this paper, collaborative use of relays to form a beamforming system with the aid of perfect channel state information (CSI) and to provide physical-layer security is investigated. In particular, a decode-and-forward-based relay beamforming design subject to total and individual relay power constraints is studied with the goal of maximizing the secrecy rate. It is shown that the total power constraint leads to a closed-form solution. The design under individual relay power constraints is formulated as an optimization problem which is shown to be easily solved using two different approaches,…
In this paper, collaborative use of relays to form a beamforming system with the aid of perfect channel state information (CSI) and to provide communication in physicallayer security between a transmitter and two receivers is investigated. In particular, we describe decode-and-forward based null space beamforming schemes and optimize the relay weights jointly to obtain the largest secrecy rate region. Furthermore, the optimality of the proposed schemes is investigated by comparing them with the outer bound secrecy rate region
We consider the full-duplex (FD) two-way amplify-and-forward relay system with imperfect cancelation of loopback self-interference (SI) and investigate joint design of relay and receive beamforming for minimizing the mean square error under a relay transmit power constraint. Due to loopback channel estimation error and limitation of analog-to-digital converter, the loopback SI cannot be completely canceled. Multiple antennas at the relay can help loopback SI suppression but beamforming is required to balance between the residual SI suppression and the desired signal transmission. Moreover, the…
A two-phase beamforming solution for secure communication using untrusted relay nodes is presented. To thwart eavesdropping attempts of relay nodes, we deliberately introduce artificial noise in the source message. After pointing out the incongruity in evaluating secrecy rate in our model for certain scenarios, we provide an SNR based frame work for secure communication. We intend to bring down the SNR at each of the untrusted relay nodes below a certain predefined threshold, whereas, using beamforming we want to boost the SNR at the destination. With this motive optimal scaling vector is eval…
Consider a simple two-way relaying channel where two single-antenna sources exchange information via a multiple-antenna relay. To such a scenario, all the existing works which can achieve full diversity order are based on the antenna/relay selection, where the difficulty to design the beamforming lies in the fact that a single beamformer needs to serve two destinations. In this paper, we propose a new full-diversity beamforming scheme which ensures that the relay signals are coherently combined at both destinations. Both analytical and numerical results are provided to demonstrate that this pr…
We investigate a relay network where a multiantenna source can potentially utilize an unauthenticated (untrusted) relay to augment its direct transmission of a confidential message to the destination. Since the relay is untrusted, it is desirable to protect the confidential data from it while simultaneously making use of it to increase the reliability of the transmission. We present a low-complexity scheme denoted as imbalanced beamforming based on linear beamforming and constellation mapping that ensures perfect physical-layer security even while utilizing the untrusted relay. Furthermore, th…
We consider a two-way relay network, where two source nodes, S1 and S2, exchange information through a cluster of relay nodes. The relay nodes receive the sum signal from S1 and S2 in the first time slot. In the second time slot, each relay node multiplies its received signal by a complex coefficient and retransmits the signal to the two source nodes, which leads to a distributed two-way beamforming system. By applying the principle of analog network coding, each receiver at S1 and S2 cancels the ``self-interference'' in the received signal from the relay cluster and decodes the message. This …
In this correspondence, we consider an amplify-and-forward relay network in which relayed information is overheard by an eavesdropper. In order to confound the eavesdropper, a wireless-powered jammer is also considered which harvests energy from a multiple-antenna source. We proposed a new secure beamforming scheme in which beamforming vector is a linear combination of the energy beamforming (EB) and information beamforming (IB) vectors. We also present a new closed-form solution for the proposed beamforming vector which is shown to achieve a higher secrecy rate as compared to the trivial EB a…
We consider a two-way relay network, where two source nodes, S1 and S2, exchange information through a cluster of relay nodes. The relay nodes receive the sum signal from S1 and S2 in the first time slot. In the second time slot, each relay node multiplies its received signal by a complex coefficient and retransmits the signal to the two source nodes, which leads to a collaborative two-way beamforming system. By applying the principle of analog network coding, each receiver at S1 and S2 cancels the "self-interference" in the received signal from the relay cluster and decodes the message. This …
In this paper, we investigate the problem of two-way relay beamforming optimization to maximize the achievable sum-rate of a simultaneous wireless information and power transfer (SWIPT) system with a full-duplex (FD) multiple-input multiple-output (MIMO) amplify-and-forward (AF) relay. In particular, we address the optimal joint design of the receiver power splitting (PS) ratio and the beamforming matrix at the relay node given the channel state information (CSI). Our contribution is an iterative algorithm based on difference of convex (DC) programming and one-dimensional searching to achieve …
In this paper, link selection for half-duplex buffer-aided relay systems is revisited. A new fixed scheduling policy referred as alternate distributed beamforming (ADB) is proposed, in which the relays are divided into two groups, with one group receiving the same information broadcast from the source and the other group transmitting the common messages to the destination via distributed beamforming in each time slot. It is worth noting that the relays used for reception and transmission are determined without the need of instantaneous channel state information (CSI). Theoretical analysis of t…
This is a companion technical report of the main manuscript "Semidefinite Relaxation and Approximation Analysis of a Beamformed Alamouti Scheme for Relay Beamforming Networks". The report serves to give detailed derivations of Lemma 1-2 in the main manuscript, which are too long to be included in the latter. In addition, more simulation results are presented to verify the viability of the BF Alamouti AF schemes developed in the main manuscript.
In this paper, linear beamforming design for amplify-and-forward relaying cellular networks is considered, in which base station, relay station and mobile terminals are all equipped with multiple antennas. The design is based on minimum mean-square-error criterion, and both uplink and downlink scenarios are considered. It is found that the downlink and uplink beamforming design problems are in the same form, and iterative algorithms with the same structure can be used to solve the design problems. For the specific cases of fully loaded or overloaded uplink systems, a novel algorithm is derived…
This paper studies simultaneous wireless information and power transfer (SWIPT) systems in two-way relaying (TWR) channels. Here, two source nodes receive information and energy simultaneously via power splitting (PS) from the signals sent by a multi-antenna relay node. Our objective is to maximize the weighted sum of the harvested energy at two source nodes subject to quality of service (QoS) constraints and the relay power constraints. Three well-known and practical two-way relay strategies are considered, i.e., amplify-and-forward (AF), bit level XOR based decode-and-forward (DF-XOR) and sy…
Relay selection enhances the performance of the cooperative networks by selecting the links with higher capacity. Meanwhile link adaptation improves the spectral efficiency of wireless data-centric networks through adapting the modulation and coding schemes (MCS) to the current link condition. In this paper, relay selection is combined with link adaptation for distributed beamforming in a two-hop regenerative cooperative system. A novel signaling mechanism and related optimal algorithms are proposed for joint relay selection and link adaptation. In the proposed scheme, there is no need to feed…
In this work, we maximize the secrecy rate of the wireless-powered untrusted relay network by jointly designing power splitting (PS) ratio and relay beamforming with the proposed global optimal algorithm (GOA) and local optimal algorithm (LOA). Different from the literature, artificial noise (AN) sent by the destination not only degrades the channel condition of the eavesdropper to improve the secrecy rate, but also becomes a new source of energy powering the untrusted relay based on PS. Hence, it is of high economic benefits and efficiency to take advantage of AN compared with the literature.…
This paper studies the wireless two-way relay channel (TWRC), where two source nodes, S1 and S2, exchange information through an assisting relay node, R. It is assumed that R receives the sum signal from S1 and S2 in one time-slot, and then amplifies and forwards the received signal to both S1 and S2 in the next time-slot. By applying the principle of analogue network (ANC), each of S1 and S2 cancels the so-called "self-interference" in the received signal from R and then decodes the desired message. Assuming that S1 and S2 are each equipped with a single antenna and R with multi-antennas, thi…
This paper proposed new hybrid, analog-digital, beamforming for a multiuser millimeter wave (mm-wave) relay system. For this system, we consider a sum rate maximization problem. The proposed hybrid beamforming is designed indirectly by considering a sum mean square error (MSE) minimization problem while utilizing the solution of digital beamforming. To this end, we assume that the digital beamforming utilizes the well known block diagonalization (BD) approach. Under this assumption, we solve our problem as follows: First, we formulate the sum rate maximization problem as the minimization of th…
In this paper, the robust distributed relay beamforming problem is solved using the worst case approach, where the problem solution has been involved because of the effect of uncertainty of channel knowledge on the quality of service (QoS) constraints. It is shown that the original robust design, which is a non-convex semi-infinite problem (SIP), can be relaxed and reformed to a semi-definite problem (SDP). Monte-Carlo simulations are presented to verify the performance improvement of our proposed robust problem over existing robust and non-robust problems in terms of transmit power and symbol…
In this work, we study the problem of relay beamforming for an underlay cognitive radio relay network using amplify-and-forward (AF) relaying technique. We consider a cognitive radio network consisting of single primary and multiple secondary transmitters/receivers. In addition, there are several relay nodes that help both primary and secondary networks. We propose a new beamforming method for relays' transmission, in which the beamforming weights at the relays are the solution of an optimization problem. The objective of the optimization problem is maximizing the worst case signal to interfer…
In this paper, we study the performance of the downlink of a cellular network with automatic repeat-request (ARQ) and a half duplex decode-and-forward shared relay. In this system, two multiple-input-multiple-output (MIMO) base stations serve two single antenna users. A MIMO shared relay retransmits the lost packets to the target users. First, we study the system with direct retransmission from the base station and derive a closed form expression for the outage probability of the system.We show that the direct retransmission can overcome the fading, however, it cannot overcome the interference…
This paper studies the secure beamforming design in a multiple-antenna three-node system where two source nodes exchange messages with the help of an untrusted relay node. The relay acts as both an essential signal forwarder and a potential eavesdropper. Both two-phase and three-phase two-way relay strategies are considered. Our goal is to jointly optimize the source and relay beamformers for maximizing the secrecy sum rate of the two-way communications. We first derive the optimal relay beamformer structures. Then, iterative algorithms are proposed to find source and relay beamformers jointly…
In this paper, link selection is investigated in half-duplex (HD) dual-hop cooperative systems with multiple antennas at the relays. Alternate distributed beamforming (ADB) scheme is revisited for buffer-aided multi-antenna relay systems, in which the relays are divided into two groups, with one group receiving the same information broadcast from the source and the other group transmitting the common messages to the destination via distributed beamforming in each time slot. It is worth noting that the relays used for reception and transmission are determined without the need of instantaneous c…
Unified performance analysis is carried out for amplify-and-forward (AF) multiple-input-multiple-output (MIMO) beamforming (BF) two-way relay networks in Rayleigh fading with five different relaying protocols including two novel protocols for better performance. As a result, a novel closed-form sum-bit error rate (BER) expression is presented in a unified expression for all protocols. A new closed-form high signal-to-noise-ratio (SNR) performance is also obtained in a single expression, and an analytical high-SNR gap expression between the five protocols is provided. We compare the performance…
We address the problem of a multi-user relay network, where multiple single-antenna node pairs want to exchange information by using a multiple antenna relay node. Due to the half-duplex constraint of the relay, the exchange of information takes place in two steps. In the first step, the nodes transmit their data to the relay, while in the second step, the relay is broadcasting the data by using linear and non-linear precoding strategies. We focus on the second step in this paper. We first consider the problem of maximizing the overall rate achievable using linear and dirty-paper type precodin…
The physical-layer security issue in the multiple non-regenerative wireless-powered relay (WPR) networks is investigated in this letter, where the idle relay is treated as a potential eavesdropper. To guarantee secure communication, the destination-based artificial noise is sent to degrade the receptions of eavesdroppers, and it also becomes a new source of energy powering relays to forward the information with power splitting (PS) technique. We propose an efficient algorithm ground on block-wise penalty function method to jointly optimize PS ratio and beamforming to maximize the secrecy rate.…
In this paper, we investigate the optimization problem of joint source and relay beamforming matrices for a twoway amplify-and-forward (AF) multi-input multi-output (MIMO) relay system. The system consisting of two source nodes and two relay nodes is considered and the linear minimum meansquare- error (MMSE) is employed at both receivers. We assume individual relay power constraints and study an important design problem, a so-called determinant maximization (DM) problem. Since this DM problem is nonconvex, we consider an efficient iterative algorithm by using an MSE balancing result to obtain …
In this study, energy-efficient deterministic adaptive beamforming algorithms are proposed for distributed sensor/relay networks. Specifically, DBSA, D-QESA, D-QESA-E, and a hybrid algorithm, hybrid-QESA, that combines the benefits of both deterministic and random adaptive beamforming algorithms, are proposed. Rigorous convergence analyses are provided for all our proposed algorithms and convergence to the global optimal solution is shown for all our proposed algorithms. Through extensive numerical simulations, we demonstrate that superior performance is achieved by our proposed DBSA and D-QES…
This paper studies a system where a set of $N$ relay nodes harvest energy from the signal received from a source to later utilize it when forwarding the source's data to a destination node via distributed beamforming. To this end, we derive (approximate) analytical expressions for the mean SNR at destination node when relays employ: i) time-switching based energy harvesting policy, ii) power-splitting based energy harvesting policy. The obtained results facilitate the study of the interplay between the energy harvesting parameters and the synchronization error, and their combined impact on mea…
In this paper, we study beamforming in decode-and-forward (DF) relaying using multiple relays, where the source node sends a secret message as well as a non-secret message to the destination node in the presence of multiple non-colluding eavesdroppers. The non-secret message is transmitted at a fixed rate $R_{0}$ and requires no protection from the eavesdroppers, whereas the secret message needs to be protected from the eavesdroppers. The source and relays operate under a total power constraint. We find the optimum source powers and weights of the relays for both secret and non-secret messages…
In this paper, we derive the optimal transmitter/ receiver beamforming vectors and relay weighting matrix for the multiple-input multiple-output amplify-and-forward relay channel. The analysis is accomplished in two steps. In the first step, the direct link between the transmitter (Tx) and receiver (Rx) is ignored and we show that the transmitter and the relay should map their signals to the strongest right singular vectors of the Tx-relay and relay-Rx channels. Based on the distributions of these vectors for independent identically distributed (i.i.d.) Rayleigh channels, the Grassmannian code…
In this paper, we deal with the performance analysis of full-duplex relaying in decode-&-forward cooperative networks with multiple-antenna terminals. More specifically, by analyzing the end-to-end statistics, we derive the accurate closed-form expressions of the end-to-end outage probability for both transmit and receive ZFBF scheme over Rayleigh fading environments. Some selected results show some interesting observations useful for system designers. Specifically, we observe that the outage performance can be improved by adopting the joint ZF-based precoding with different antenna configurat…
In this paper, robust transceiver design based on minimum-mean-square-error (MMSE) criterion for dual-hop amplify-and-forward MIMO relay systems is investigated. The channel estimation errors are modeled as Gaussian random variables, and then the effect are incorporated into the robust transceiver based on the Bayesian framework. An iterative algorithm is proposed to jointly design the precoder at the source, the forward matrix at the relay and the equalizer at the destination, and the joint design problem can be efficiently solved by quadratic matrix programming (QMP).
This paper considers the joint design of user power allocation and relay beamforming in relaying communications, in which multiple pairs of single-antenna users exchange information with each other via multiple-antenna relays in two time slots. All users transmit their signals to the relays in the first time slot while the relays broadcast the beamformed signals to all users in the second time slot. The aim is to maximize the system's energy efficiency (EE) subject to quality-of-service (QoS) constraints in terms of exchange throughput requirements. The QoS constraints are nonconvex with many …
In this paper we explore the use of full-duplex radio to improve the spectrum efficiency in a two-way relay channel where two sources exchange information through an multi-antenna relay, and all nodes work in the full-duplex mode. The full-duplex operation can reduce the overall communication to only one phase but suffers from the self-interference. Instead of purely suppressing the self-interference, we aim to maximize the end-to-end performance by jointly optimizing the beamforming matrix at the relay which uses the amplify-and-forward protocol as well as the power control at the sources. To…
In this paper, we consider a non-orthogonal multiple access cognitive radio network, where a full-duplex multi-antenna relay assists transmission from a base station (BS) to a cognitive far user, whereas, at the same time, the BS transmits to a cognitive near user. Our objective is to enlarge the far-near user rate region by maximizing the rate of the near user under a constraint that the rate of the far user is above a certain threshold. To this end, a non-convex joint optimization problem of relay beamforming and the transmit powers at the BS and cognitive relay is solved as a semi-definite …
We analyze the outage performance of a two-way fixed gain amplify-and-forward (AF) relay system with beamforming, arbitrary antenna correlation, and co-channel interference (CCI). Assuming CCI at the relay, we derive the exact individual user outage probability in closed-form. Additionally, while neglecting CCI, we also investigate the system outage probability of the considered network, which is declared if any of the two users is in transmission outage. Our results indicate that in this system, the position of the relay plays an important role in determining the user as well as the system ou…
In this paper, system design for the multi-input multi-output (MIMO) relay broadcast channel with individual signal-to-interference-plus-noise ratio (SINR) constraints at the mobile stations (MS) is considered. By exploring the structure of downlink (DL) uplink (UL) duality at either the base station (BS) or the relay station (RS), we propose two schemes of joint power allocation and beamforming design at the BS and the RS. The problem of existence of feasible solutions under practical power constraints at the BS and the RS with given SINR targets is considered first. Then the problem of sum p…
In this paper, we consider a dual-hop Multiple Input Multiple Output (MIMO) relay wireless network, in which a source-destination pair both equipped with multiple antennas communicates through a large number of half-duplex amplify-and-forward (AF) relay terminals. Two novel linear beamforming schemes based on the matched filter (MF) and regularized zero-forcing (RZF) precoding techniques are proposed for the MIMO relay system. We focus on the linear process at the relay nodes and design the new relay beamformers by utilizing the channel state information (CSI) of both backward channel and forw…
This paper is on beamforming in wireless relay networks with perfect channel information at relays, the receiver, and the transmitter if there is a direct link between the transmitter and receiver. It is assumed that every node in the network has its own power constraint. A two-step amplify-and-forward protocol is used, in which the transmitter and relays not only use match filters to form a beam at the receiver but also adaptively adjust their transmit powers according to the channel strength information. For a network with any number of relays and no direct link, the optimal power control is…
We consider a multiple-input multiple-output (MIMO) relaying boardcast channel in downlink cellular networks, where the base station and the relay stations are both equipped with multiple antennas, and each user terminal has only a single antenna. In practical scenarios, channel estimation is imperfect at the receivers. Aiming at maximizing the SINR at each user, we develop two robust linear beamforming schemes respectively for the single relay case and the multi-relay case. The two proposed schemes are based on sigular value decomposition (SVD), minimum mean square error (MMSE) and regularize…
In this paper, we consider a reconfigurable intelligent surface (RIS)-assisted two-way relay network, in which two users exchange information through the base station (BS) with the help of an RIS. By jointly designing the phase shifts at the RIS and beamforming matrix at the BS, our objective is to maximize the minimum signal-to-noise ratio (SNR) of the two users, under the transmit power constraint at the BS. We first consider the single-antenna BS case, and propose two algorithms to design the RIS phase shifts and the BS power amplification parameter, namely the SNR-upper-bound-maximization …
Reconfigurable intelligent surfaces (RIS) have drawn considerable attention recently due to their controllable scattering elements that are able to direct electromagnetic waves into desirable directions. Although RISs share some similarities with relays, the two have fundamental differences impacting their performance. To harness the benefits of both relaying and RISs, a multi-user communication system is proposed in this paper wherein a relay and an RIS cooperate to improve performance in terms of energy efficiency. Using singular value decomposition (SVD), semidefinite programming (SDP), and…
In this paper, a general cognitive radio system consisting of a set of users with different level of spectrum access including two primary transceivers and several types of secondary users is considered. It is assumed that two secondary users operate based on an underlay model at the same frequency bandwidth and at the same time as the primary users based on a multiple access broadcast channel (MABC) bidirectional beamforming scheme. Other secondary users provide a relaying service to the primary users in exchange for the opportunity to send their messages towards their own destinations for a …
In this paper, we consider a dual-hop Multiple Input Multiple Output (MIMO) wireless relay network in the presence of imperfect channel state information (CSI), in which a source-destination pair both equipped with multiple antennas communicates through a large number of half-duplex amplify-and-forward (AF) relay terminals. We investigate the performance of three linear beamforming schemes when the CSI of relay-to-destination (R-D) link is not perfect at the relay nodes. The three efficient linear beamforming schemes are based on the matched-filter (MF), zero-forcing (ZF) precoding and regular…
We study amplified-and-forward (AF)-based two-way relaying (TWR) with multiple source pairs, which are exchanging information through the relay. Each source has single antenna and the relay has multi-antenna. The optimal beamforming matrix structure that achieves maximum signal-to-interference-plus-noise ratio (SINR) for TWR with multiple source pairs is derived. We then present two new non-zero-forcing based beamforming schemes for TWR, which take into consideration the tradeoff between preserving the desired signals and suppressing inter-pair interference between different source pairs. Join…
A novel transmission protocol is conceived for a multi-user, multi-relay, multiple-input--multiple-output orthogonal frequency-division multiple-access (MIMO-OFDMA) cellular network based on joint transmit and receive beamforming. More specifically, the network's MIMO channels are mathematically decomposed into several effective multiple-input--single-output (MISO) channels, which are spatially multiplexed for transmission. For the sake of improving the attainable capacity, these MISO channels are grouped using a pair of novel grouping algorithms, which are then evaluated in terms of their per…
In this paper, multi-stream transmission in interference networks aided by multiple amplify-and-forward (AF) relays in the presence of direct links is considered. The objective is to minimize the sum power of transmitters and relays by beamforming optimization under the stream signal-to-interference-plus-noise-ratio (SINR) constraints. For transmit beamforming optimization, the problem is a well-known non-convex quadratically constrained quadratic program (QCQP) that is NP-hard to solve. After semi-definite relaxation (SDR), the problem can be optimally solved via alternating direction method …
In this paper, we propose a new distributed energy beamforming and information transfer (DEBIT) scheme for realizing simultaneous wireless information and power transfer (SWIPT) in multiway relay networks (MWRNs), where multiple single-antenna users exchange information via an energy-constrained single-antenna relay node. We investigate the optimal transceiver designs to maximize the achievable sum-rate or the harvested power. The resultant sum-rate maximization problem is non-convex and the global optimal solution can be obtained through a three-dimensional search in combination with conventi…
We derive optimal SNR-based transmit antenna selection rules at the source and relay for the nonregenerative half duplex MIMO relay channel. While antenna selection is a suboptimal form of beamforming, it has the advantage that the optimization is tractable and can be implemented with only a few bits of feedback from the destination to the source and relay. We compare the bit error rate of optimal antenna selection at both the source and relay to other proposed beamforming techniques and propose methods for performing the necessary limited feedback.
This paper deals with joint source and relay beamforming (BF) design for an amplify-and-forward (AF) multi-antenna multirelay network. Considering that the channel state information (CSI) from relays to destination is imperfect, we aim to maximize the worst case received signal-to-noise ratio (SNR). The associated optimization problem is then solved in two steps. In the first step, by fixing the source BF vector, a semi-closed form solution of the relay BF matrices is obtained, up to a power allocation factor. In the second step, the global optimal source BF vector is obtained based on the Pol…
