A 3D thermoelectric numerical model is used to investigate different internal heat loss mechanisms for a thermoelectric generator with bismuth telluride p- and n-legs. The model considers all thermoelectric effects, temperature dependent material parameters and simultaneous convective, conductive and radiative heat losses, including surface to surface radiation. For radiative heat losses it is shown that for the temperatures considered here, surface to ambient radiation is a good approximation of the heat loss. For conductive heat transfer the module efficiency is shown to be comparable to the case of radiative losses. Finally, heat losses due to internal natural convection in the module is shown to be negligible for the millimetre sized modules considered here. The combined case of radiative and conductive heat transfer resulted in the lowest efficiency. The optimized load resistance is found to decrease for increased heat loss. The leg dimensions are varied for all heat losses cases and it is shown that the ideal way to construct a TEG module with minimal heat losses and maximum efficiency is to either use a good insulating material between the legs or evacuate the module completely, and use small and wide legs closely spaced.
Studying the applicability of different thermoelectric materials for efficiency calculation in hybrid thermoelectric generator for waste heat recovery from automobile and steel industry
在这项工作中,我们研究了不同的热电材料,如$Bi_2Te_3$,$Sb_{2}Te_{3}$,$PbTe$,$TAGS$,$CeFe_{4}Sb_{12}$,$SiGe$和$TiO_{1.1}$的热电发电机(TEG)的效率估计的适用性。由${Be_{2}Te_{3}}$或$Sb_{2}Te_{3}$组成的TEG在310 K ~ 500 K温度范围内的效率为7%. $PbTe$或$TAGS$或$CeFe_{4}Sb_{12}$在500 K - 900 K温度范围内均能使$\sim$达到6%,而$SiGe$或$TiO_{1.1}$在较高温度范围($\sim$ 1200 K)也有显著的效率。在这里,我们报告的效率的提高,通过使用杂交技术的不同组合的上述材料。从相容性因素的角度对TEG组件的两种不同材料进行了混合。为此,在310 K ~ 900 K温度范围内,由${Be_{2}Te_{3}}$和$PbTe$、${Be_{2}Te_{3}}$和$TAGS$、$Bi_{2}Te_{3}$和$CeFe_{4}Sb_{12}$混合而成的TEG的总效率的建议值分别为12%、14%和11.88%,可以安装在汽车上。对于钢铁工业和航天器应用(直到1200 K),$Bi_{2}Te_{3}$、$PbTe$和$SiGe$的混合; ${Be_{2}Te_{3}}$和$TiO_{1.1}$分别产生$\sim$ …
Thickness optimization of the output power and effective thermoelectric figure of merit of thin thermoelectric generator
传统的热电品质因数和功率因数不足以作为热电材料的薄膜质量的量度,其中功率转换效率取决于薄膜尺寸。考虑薄膜尺寸的影响,引入有效热电优值和有效塞贝克系数,保证最大能量转换效率随有效热电优值的增大而增大。同样,定义了有效功率因数。通过介绍Bi $_2$ Te $_3$和PEDOT的典型材料特性,研究了有效优值和有效功率因数的厚度依赖性。
Calculation of Efficiency and Power Output by Considering Different Realistic Prospects for Recovering Heat from Automobile using Thermoelectric Generator
Thermoelastic Harvesting Outperforming Thermoelectric Generators Below 100 °C
Helmholtz-Zentrum Dresden–Rossendorf(德累斯顿-罗森多夫亥姆霍兹中心);TUD Dresden University of Technology(德累斯顿工业大学);Hochschule für Technik und Wirtschaft Dresden(德累斯顿应用技术大学)
本文介绍的工作描述了热电效应的空心块热废物收集的目的。该研究包括开发一个数值模型形成的热传递方程耦合到热电效应方程研究热电发电机(TEG)纳入黎巴嫩空心块通过两个模拟使用有限差分格式和使用有限元格式。结果表明,对于ΔT=30K,由碲化铋锑制成的单个8.6 x 0.4 x 0.4 cm 3热电腿产生的电压为5.85 mV。采用这两种方法对一个空心块内装有3个TEG的设计进行了测试和数值验证,在ΔT=30K时得到的主要结果表明,电压ΔV=0.72V,电流I= 0.06A,品质因数ZT=0.55。然后,出于经济目的对设计进行了优化。
Quantitative measurements of transverse thermoelectric generation and cooling performances in SmCo$_5$/Bi$_{0.2}$Sb$_{1.8}$Te$_3$-based artificially tilted multilayer module
High-entropy Fe$_2$VAl-based thermoelectric modules with improved conversion efficiency
TU Wien(维也纳工业大学);UCLouvain(天主教鲁汶大学);Los Alamos National Laboratory(洛斯阿拉莫斯国家实验室);German Aerospace Center (DLR)(德国航空航天中心);Institute of Solid State Physics, TU Wien(维也纳工业大学固体物理研究所);Institute of Mechanics, Materials, and Civil Engineering, IMAP, UCLouvain(天主教鲁汶大学IMAP力学、材料与土木工程研究所);Materials Physics Applications – Quantum, Los Alamos National Laboratory(洛斯阿拉莫斯国家实验室量子材料物理应用部门);German Aerospace Center (DLR) – Institute for Frontier Materials on Earth and in Space(德国航空航天中心地球与太空前沿材料研究所);Institute of Chemical Technologies and Analytics, TU Wien(维也纳工业大学化学技术与分析研究所)